Updated Nov 16, 2026· 14 min read

Key takeaways

  • Compare the best audio mixers for podcasting, from the PodTrak P8 and Mixcast 4 to the ProFX10v3, MG10XU, and Notepad-12FX, by mic inputs, pads, and formats.

Podcasting rewards clean voices and punishes fiddly gear, so the audio mixers for podcasting in this guide fall into two camps: dedicated podcast stations that record on their own, and compact analog mixers that feed a computer. Both camps were checked the same way, on the figures their product pages publish.

What podcasting asks from an audio mixer

A podcast mixer has one main job: capture several voices at matched, clean levels, with processing that keeps speech clear and monitoring that lets every guest hear themselves. Recording flexibility comes second, but it decides how much editing work waits for you after the session ends.

Mic inputs, gain, and headphone feeds

Count the people first. A solo show needs one microphone input; a four-person panel needs four, each with its own gain, processing, and headphone feed. Preamp gain matters because popular broadcast dynamic microphones are quiet designs, and the product pages here state gain figures from 60 dB up to 70 dB.

The Zoom PodTrak P8 leads on count, with six XLR mic inputs at up to 70 dB of gain and six independent headphone outputs, one per participant. The Tascam Mixcast 4 covers four people with four combo mic inputs, a 66.5 dB gain range, and four headphone outputs. The three analog mixers, the Mackie ProFX10v3, Yamaha MG10XU, and Soundcraft Notepad-12FX, each provide four mic preamps, so a host plus three guests is their natural panel size.

Phantom power decides whether condenser microphones can join the panel. The PodTrak P8 offers +48V phantom power on its XLR inputs, the Mixcast 4 switches each mic channel between condenser, with 48V, and dynamic, and the MG10XU and Notepad-12FX both provide +48V for their mic channels.

Processing that keeps speech clear

Speech processing is where podcast gear earns its keep. A compressor evens out a guest who leans in and out, a low-cut filter removes desk rumble and handling noise, and a de-esser tames harsh sibilance. The dedicated stations build these tools per channel; the analog mixers offer simpler, faster controls.

Every PodTrak P8 mic channel carries a limiter, a low cut filter, tone control, and a compressor/de-esser. The Mixcast 4 goes deeper, with easy sound settings named Deep, Mid, and Bright or a manual two-band semi-parametric EQ, easy or manual compression, a de-esser, and a noise suppressor, plus reverb on one mic channel. Tascam also adds an auto-mix function that adjusts levels automatically and sets mic priority, which helps when guests talk over each other.

The analog trio keeps dynamics simple: the ProFX10v3 and MG10XU both use single-knob compression, the ProFX10v3 adding a 100 Hz low cut filter at 18 dB per octave on its mic channels, while the MG10XU pairs its compressors with an 80 Hz high-pass filter and 26 dB pads for hot signals. The Notepad-12FX gives its mic channels 100 Hz high-pass filters and 3-band EQ, leaving compression to your recording software.

Remote guests and mix-minus

Most podcasts eventually host someone who is not in the room, sometimes on every episode. The caller must hear the panel without hearing their own voice echoed back, which is the mix-minus job, and the two podcast stations here were designed around exactly that requirement.

The Mixcast 4 includes mix-minus for call-ins arriving by Bluetooth, USB input, or a 4-pole TRRS phone cable. The PodTrak P8 gives its smartphone channel and its USB-mode channel mix-minus as well, and an optional Bluetooth receiver, sold separately, adds a wireless phone path. The analog mixers have no dedicated mix-minus; remote guests on those rigs are usually handled inside the recording software, with the mixer sending the local voices only.

Sound pads are the other live-production tool. The PodTrak P8 has nine assignable pads in four banks, 36 clips in total with 13 sounds preloaded, and the Mixcast 4 has eight pads in eight banks, up to 64 sounds, which can also trigger voice effects such as pitch transformation and reverb. The analog mixers leave intros and stingers to the computer.

The five audio mixers for podcasting in detail

Each product below was checked on its maker’s or a detailed product page, and the numbers quoted are the ones those pages state: mic input counts, gain ranges, recording formats, USB configurations, and the processing list for each mic channel, plus dimensions and weight.

Zoom PodTrak P8

The PodTrak P8 is a portable multitrack podcast recorder built for panels: six XLR mic inputs with selectable +48V phantom power and up to 70 dB of gain each, which Zoom notes is enough for demanding microphones such as the SM7B. Each channel has its own volume slider, mute button, and ON AIR indicator.

Processing runs per channel, with a limiter, low cut filter, tone control, and compressor/de-esser on every mic input, and the controls are color-coded to match the inputs and outputs. Six 3.5mm headphone outputs give every participant an independent mix with its own level control, and balanced TRS speaker outputs feed studio monitors. A 4.3-inch full-color touchscreen handles settings, monitoring, and onboard editing, so a session can be trimmed without opening a computer.

Recording goes to an SD card in WAV format at 44.1 kHz and 16-bit, up to 13 tracks at once counting the mic channels, the smartphone input, the sound pads, and the stereo mix. Remote guests arrive through the TRRS smartphone channel or by switching channel 6 to USB mode, both with mix-minus, and the USB-C port also works as a 44.1 kHz, 16-bit, 2-in/2-out audio interface. Power comes from four AA batteries for about two hours of recording, the included AC adapter, or USB. The unit measures 295 x 248 x 61 mm and weighs 1.43 kg.

Tascam Mixcast 4

The Mixcast 4 is a podcast station for up to four people: four XLR/TRS combo mic inputs with a 66.5 dB gain range, an equivalent input noise of -125 dBu or better, a 101 dB signal-to-noise ratio, and distortion rated at 0.003 percent. Four headphone outputs with independent volume controls cover the panel.

Eight large channel faders mix the mics, USB, mobile, Bluetooth, and sound pad sources. Its auto-mix function adjusts mic levels automatically and sets mic priority, and each mic channel offers easy sound settings or manual EQ, compression in easy or manual form, a de-esser, and a noise suppressor. A talkback button lets the host speak to the participants off air, and a mark button flags moments during recording for later editing.

Recording runs to an SD card as WAV at 48 kHz and 24-bit, up to 14 tracks at once, twelve channels plus the stereo mix, and SDXC cards up to 512 GB are supported. As a USB interface it presents 14 inputs and two outputs to a computer. Mix-minus covers call-ins by Bluetooth, USB, or TRRS cable, Bluetooth audio also streams music from a phone, and the Tascam Podcast Editor software handles pad assignment, editing, and archiving. The unit measures 375 x 57 x 264 mm, weighs 2.55 kg, and runs from a 12 V adapter at 12.5 W maximum.

One producer-friendly setting deserves a mention: the USB output signal can be delayed by up to 2000 ms to compensate for the delay between the unit’s audio and video played from a computer, which helps when the podcast is also filmed and the two need to stay in sync. The touchscreen interface also offers nine language options, a small thing that matters for international panels and borrowed studios.

The Mixcast 4 also works with Tascam’s Podcast Editor software, and the multitrack SD recording is what makes that pairing useful: because the session lands as separate tracks in the 48 kHz, 24-bit WAV files, levels can be revisited after recording instead of being locked into a stereo mix. For shows that record first and polish later, that post-session freedom is the station’s main advantage over the analog mixers in this guide, which hand the computer a finished mix.

Mackie ProFX10v3

The ProFX10v3 is a 10-channel analog mixer that podcasters use as a front end for a computer. Four Onyx mic preamps provide up to 60 dB of gain, joined by stereo line channels for music players and other sources, and the channels carry 3-band EQ rated at plus or minus 15 dB at 80 Hz, 2.5 kHz, and 12 kHz.

For voices, the useful tools are the single-knob compression and the low cut filter, 18 dB per octave at 100 Hz, on the mic channels, which together keep levels steady and remove low rumble before recording. The GigFX engine adds 24 effects, including reverbs and delays, more often used for a music intro or a live segment than for speech itself.

The USB interface is a 2×4 design at 24-bit and up to 192 kHz: the stereo mix goes to the computer, and two stereo returns come back, which Mackie notes allows two custom mixes to be created on the computer and sent back into the mixer. Latency-free monitoring blends the direct mixer feed with the computer output on one knob. The mixer measures 84 x 272 x 302 mm, weighs 2.2 kg, and includes the Waveform OEM recording software with a plug-in collection.

The construction suits a desk that also hosts live work: a solid steel chassis with ABS side protection, and covers and carry bags available from the maker for moving it between rooms or venues.

Yamaha MG10XU

The MG10XU is Yamaha’s 10-channel analog console: four mono mic/line channels with D-PRE discrete class-A preamps, three stereo line channels, and a 2-in/2-out USB interface at 24-bit and up to 192 kHz. The mic channels carry +48V phantom power, a 26 dB pad, and an 80 Hz high-pass filter at 12 dB per octave.

Yamaha publishes the quiet numbers: an equivalent input noise of -128 dBu, total harmonic distortion of 0.003 percent at high output, and crosstalk of -83 dB. The 1-knob compressors work across a threshold range of +22 dBu to -8 dBu with ratios up to 4:1, and the 3-band EQ gives plus or minus 15 dB at 10 kHz, 2.5 kHz, and 100 Hz.

The SPX effects processor holds 24 programs for reverb and delay touches, and there is one aux send, a monitor output, and a phones output. Metering is a two-by-seven-segment LED ladder, and a peak LED on each mono channel lights when the post-EQ signal comes within 3 dB of clipping, which makes gain setting for speech straightforward.

For podcasting, the workflow is record-the-mix: the stereo bus goes to the computer or a recorder, and the bundled Cubase AI download covers editing. The metal chassis measures 244 x 294 mm across the desk, stands 71 mm tall, weighs 2.1 kg, and draws 22.9 W.

Soundcraft Notepad-12FX

The Notepad-12FX is a compact 12-channel analog mixer with four Soundcraft mic preamps, the most channels in this guide at the analog end. The mic channels include phantom power, 100 Hz high-pass filters, and 3-band EQs, and channels 1 and 3 add Hi-Z instrument inputs, handy when a podcast doubles as a music session.

Four more channels take line-level sources such as keyboards and playback devices, and the Lexicon effects engine provides delay, chorus, and reverb with a parameter knob and tap tempo, so a touch of reverb on a voice or an intro is available without plug-ins. Outputs include balanced XLR mains, a 1/4-inch aux output, and a headphone jack that switches between main and aux feeds.

Its USB connection is a 4-in/4-out interface, the widest USB path among the analog mixers here, which lets a recording program capture more than a plain stereo mix and return audio for monitoring or playback. For a podcaster who records into a DAW and wants separate tracks to edit, that is the Notepad’s main advantage over its two analog rivals in this guide. The aux output can also feed a separate recorder, which gives a podcast a simple backup recording path.

Comparing audio mixers for podcasting side by side

The table gathers the figures that shape a podcast setup: how many microphones and headphone feeds each unit supports, how much gain the preamps offer, and how the recording is captured. Use it to shortlist, then confirm the workflow details in the notes above.

Model Mic inputs Gain Headphone outputs Recording
Zoom PodTrak P8 6 XLR Up to 70 dB 6 SD card, 13 tracks, 44.1 kHz/16-bit
Tascam Mixcast 4 4 combo 66.5 dB range 4 SD card, 14 tracks, 48 kHz/24-bit
Mackie ProFX10v3 4 Onyx Up to 60 dB 1 USB 2×4, 24-bit/192 kHz
Yamaha MG10XU 4 D-PRE Not stated on page 1 USB 2×2, 24-bit/192 kHz
Soundcraft Notepad-12FX 4 Not stated on page 1 USB 4×4

Stations that record alone versus mixers that feed a computer

The PodTrak P8 and Mixcast 4 record multitrack to SD cards with no computer in the room, and both add onboard editing support, the P8 through its touchscreen and the Mixcast 4 through its companion editor software. That independence suits panels recorded in living rooms, offices, or on location.

The P8’s battery option extends it to places without a spare outlet, and its AC adapter and USB power options cover the desk-bound days in between.

The analog mixers assume a computer is present and put their value in the preamps, EQ, and hands-on control. The trade is editing depth: a stereo mix from the ProFX10v3 or MG10XU is finished when you stop recording, while the Notepad-12FX’s 4-in/4-out USB and the stations’ multitrack files let you rebalance voices afterward.

Pads, effects, and live production

Shows that play intros, ads, and stingers live need pads, and only the two stations have them: nine pads in four banks on the P8, eight pads in eight banks on the Mixcast 4. The Mixcast’s pads can also fire voice effects, and its talkback and mark buttons serve a producer running the session while others talk.

The analog mixers answer with effects engines meant for music: 24 GigFX presets on the ProFX10v3 and 24 SPX programs on the MG10XU, plus Lexicon reverb, chorus, and delay on the Notepad-12FX. For speech, these are garnish rather than the meal, but for a show with live music segments they are genuinely useful.

The P8 adds one live-production trick of its own: a channel whose ON AIR switch is off can still be heard in the headphones without being recorded or sent to the speakers or USB, which Zoom suggests for sidebar conversations and for preparing guests during breaks.

Choosing among audio mixers for podcasting

Decide first whether the mixer must record by itself, then count microphones and remote guests. Those three answers narrow this list quickly: the stations split by panel size and recording format, and the analog mixers split by USB width and the preamp numbers their makers publish.

Solo and two-person shows

A solo host or a pair can use any model here, so the choice turns on workflow. The analog mixers keep the budget of desk space small and the controls immediate, and the MG10XU’s published noise figures, -128 dBu equivalent input noise, are the strongest of the three for a single quiet voice in a quiet room.

If the show is recorded away from the desk, the PodTrak P8’s battery power and touchscreen editing travel better, and its spare inputs mean a guest microphone can stay connected. The Mixcast 4’s auto-mix helps a two-person show where neither host wants to ride faders.

Panels of three or more

Panels are where headphone feeds decide the shortlist. Only the PodTrak P8 and Mixcast 4 give every guest a headphone output; the analog mixers provide a single phones output, so a panel on those rigs needs a separate headphone amplifier, which is a normal and inexpensive addition but one more box to plan for.

For five or six voices, the P8 is the only fit here, with six mic inputs and six headphone outputs. For four voices with multitrack files at 48 kHz and 24-bit, the Mixcast 4 is the match, and its mic priority auto-mix keeps cross-talk from swamping the recording.

Interview shows with remote guests

Interview podcasts live on call quality. The Mixcast 4 takes call-ins by Bluetooth, USB, or phone cable with mix-minus on each path, and the PodTrak P8 covers phone and USB guests with mix-minus, adding Bluetooth through an optional receiver. Both record the caller as part of the session rather than as a separate file to sync later.

On an analog mixer, the standard approach is to run the call inside the computer’s recording software and send the caller a feed of the local mix. It works, but the mixer itself contributes only its preamps and monitoring, so interview-heavy shows get more from the stations.

Setup checks before your first episode

Record a ten-minute rehearsal with every microphone, guest feed, and sound pad you plan to use, then listen to it on earbuds and on a speaker. Levels that look right on meters can still hide a humming cable, a caller set too low, or a compressor pumping on one voice, and rehearsal is the cheap place to find all three.

Gain, processing, and headphone levels

Set each mic channel’s gain with the speaker talking at show volume and distance, then switch on that channel’s processing one piece at a time: low cut first, then compression, then de-esser where fitted. On the analog mixers, the single-knob compressors make this quick.

On the stations, the easy sound settings give a starting point before you open manual controls.

Give every guest their own headphone level check, because people ask for very different volumes. On the P8 and Mixcast 4 each feed has its own control; on a shared phones output, agree the level before recording and leave it alone during the show.

Recording format and file checks

Confirm the recorder’s format before the session, not after: the P8 writes 44.1 kHz, 16-bit WAV files and the Mixcast 4 writes 48 kHz, 24-bit WAV files, and your editing software and any co-host’s files should match the session rate. Check that the SD card is formatted in the unit and that a test file plays back from the card itself.

For the analog mixers, record a test through USB and confirm the computer received the mix at the level the meters suggested, and that the return path plays back without doubling or echo. Then label the session files while the setup is still fresh in your mind. Keep a spare card in the bag as well; a formatted card ready in the unit beats a full one discovered mid-session.

Conclusion

For panels and location work, the PodTrak P8 and Mixcast 4 record complete shows on their own; for computer-based setups, the ProFX10v3, MG10XU, and Notepad-12FX trade multitrack recording for analog control, published preamp quality, and wider or simpler USB paths. Let the panel size and the guest list make the final call.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.