Key takeaways
- Compare six mixers for podcasting 5 preamp setups and above, with six to eight mic preamps, gain and noise figures, multitrack recording and phantom power.
The mixers for podcasting 5 preamp shoppers are really asking for one thing: enough microphone inputs for a whole panel, each with its own preamp. Every mixer in this guide states six, seven or eight mic preamps on its product page, so five or more voices can record together in one room, at one table.
Quick verdict
Short on time? The Soundcraft Signature 12 MTK and Zoom LiveTrak L-12 tie at the top with eight mic preamps each. The Mackie ProFX12v3 offers seven, and the Zoom PodTrak P8 is the only dedicated podcast station here, with six mic inputs and six headphone outputs.
A five-preamp floor changes the shape of a podcast mixer. Below it sit the two-, three- and four-mic units built for solo hosts and pairs; at six preamps and above, the mixer can seat a full panel with a spare channel for a phone guest, a playback device or a producer’s microphone. The six models here reach that count in different ways: two are digital mixer-recorders that capture every channel to an SD card, one is a podcast station built around six seats, and three are analog consoles that send a stereo mix, or in the Soundcraft’s case full multitrack, to a computer over USB.
Preamp count is only the entry ticket. Gain range decides whether quiet dynamic microphones reach healthy levels, equivalent input noise decides how clean that gain is, and phantom power decides whether condenser microphones can join the panel. The sections below keep the stated counts front and center, then compare those supporting figures as published, because a panel of five voices exposes weak preamps faster than any solo recording.
| Product | Mic preamps as stated | Preamp gain | Recording path |
|---|---|---|---|
| Soundcraft Signature 12 MTK | 8 Ghost preamps | Not stated on opened pages | 14-in/12-out USB multitrack |
| Zoom LiveTrak L-12 | 8 preamps | Up to +60 dB | 14 tracks to SD card; 14-in/4-out USB |
| Mackie ProFX12v3 | 7 Onyx preamps | Up to 60 dB | USB stereo mix, 24-bit/192 kHz |
| Zoom PodTrak P8 | 6 mic inputs | Up to 70 dB | 13 tracks to SD card |
| Yamaha MG12XU | 6 D-PRE preamps | Not stated on opened page | USB stereo mix, 24-bit/192 kHz |
| Zoom LiveTrak L-8 | 6 preamps | Not stated on opened page | 12 tracks to SD card; 12-in/4-out USB |
How we selected
The rule for this guide was strict: a mixer qualified only if its opened product page states five or more mic preamps, or the same number of microphone inputs with preamp gain. Channel totals were never converted into preamp counts, and models whose pages state four or fewer preamps were excluded, however good they are.
That rule produces a particular mix of products. Dedicated podcast stations mostly stop at four mic inputs, so only the six-input PodTrak P8 represents that category here. The rest are panel-capable consoles and mixer-recorders that podcasters adopt when a show outgrows four seats: they bring more preamps, more EQ and more routing, at the cost of more setup. Each entry below leads with the stated preamp count and the page’s own gain and noise figures where published, then covers the recording path, because a six-voice show needs either multitrack files or a well-managed stereo mix.
Six mixers for podcasting 5 preamp panels
The six mixers below state between six and eight mic preamps. Each entry starts with the count and where it sits in the channel layout, then covers gain, noise, phantom power, per-channel processing and how the show gets recorded, so panels can compare like for like across analog and digital designs.
Soundcraft Signature 12 MTK
The Signature 12 MTK states the joint-highest count in this guide: its maker’s specification table lists 12 channels with 8 Soundcraft Ghost Preamps, drawn from the company’s top-of-the-line professional consoles, with high headroom, a wide dynamic range and a superb signal to noise ratio.
Each of the eight mic channels carries the Sapphyre EQ, a three-band design with one band of swept mids, and the board adds dbx limiters on two inputs to catch loud guests before they clip. A single Lexicon effects engine provides reverbs, delays, choruses and modulations, and the GB Series routing offers three auxes and subgroups (two mono, one stereo) with pre and post switching, on 60 mm faders. For podcasting, the deciding feature is the USB interface: 14-in/12-out with multitrack recording and playback at 24-bit/48 kHz, so every panel member lands on a separate track in the DAW rather than a summed stereo file. Switchable Hi-Z inputs take instruments directly, high-pass filters and 48 V phantom power cover all mic channels, and the tour-grade metal housing with an internal universal power supply suits a desk that travels. Ableton Live Lite and the Lexicon MPX-L plug-in are included as downloads.
- Mic preamps: 8 Ghost preamps across 12 channels
- EQ: Sapphyre 3-band with swept mid on the mic channels
- Dynamics: dbx limiters on 2 inputs; Lexicon effects, single engine
- USB: 14-in/12-out multitrack, 24-bit/48 kHz
- Routing: 3 auxes, subgroups 2 mono/1 stereo, 60 mm faders
- Phantom power: 48 V on all mic channels; switchable Hi-Z inputs
- Dimensions 380 x 113 x 388 mm; weight 5.86 kg
Pick the Signature 12 MTK for the largest panels that record to a computer: eight preamps with multitrack USB is the strongest combination here for post-production. It has no onboard recording, so the computer is part of every session, and there are no headphone outs beyond the standard monitoring for the operator.
Zoom LiveTrak L-12
The LiveTrak L-12 also states eight mic preamps, this time on eight mono XLR and TRS combo channels in a 12-channel digital mixer that records while it mixes, with gain from +16 to +60 dB and an equivalent input noise of -128 dBu at full gain on every mic channel.
Every mono channel has a one-knob compressor, a three-band EQ with a sweepable mid (100 Hz to 8 kHz), a low-cut filter at 75 Hz and a channel fader, with Hi-Z switching on channels 1 and 2 and a 26 dB pad on channels 3 to 8. Phantom power at +48 V switches in two groups, channels 1 to 4 and 5 to 8, which suits panels mixing condenser and dynamic microphones. The L-12 records 14 tracks at 44.1 or 48 kHz, or 12 at 96 kHz, as WAV files to SD cards up to 1 TB, with tracks captured before EQ and effects so they can be remixed later; it also works as a 14-in/4-out USB audio interface and can record to a computer and the card at the same time. Five powered headphone outputs each carry a custom mix, a podcast-friendly feature the analog boards cannot match, and nine scene memories store full setups for recurring shows. Sixteen send effects cover delay and reverb duties, and a built-in slate mic and metronome support session work.
- Mic preamps: 8 on combo channels; gain +16 to +60 dB; EIN -128 dBu
- Per channel: one-knob compressor, 3-band EQ with swept mid, low cut
- Phantom power: +48 V in two groups (channels 1-4, 5-8)
- Recording: 14 tracks to SD card; 14-in/4-out USB interface
- Headphone outputs: 5 powered, each with a custom mix
- Effects: 16 send effects; 9 scene memories; slate mic built in
- Dimensions 445 x 282 x 70.5 mm; weight 2.53 kg
Choose the L-12 when the panel records away from a computer or when every participant needs their own headphone mix. Its two stereo line channels and effects are live-sound inheritances, but the preamp count, multitrack card recording and five mixes make it a natural panel desk.
Mackie ProFX12v3
The ProFX12v3 states seven Onyx mic preamps in a 12-channel analog mixer: four mono mic channels plus mic inputs on the three stereo channels (5/6, 7/8, 9/10), each preamp offering up to 60 dB of gain with a mic gain range of 0 to +60 dB across the board.
Channels 1 and 2 use combo XLR and TRS jacks with a Hi-Z switch for instruments, channels 3 and 4 take XLR and 1/4-inch inputs, and the stereo channels pair an XLR mic input with stereo line inputs. All mic channels share +48 V phantom power from a single switch, a 100 Hz low-cut filter at 18 dB per octave, and three-band EQ at 80 Hz, 2.5 kHz and 12 kHz. One-knob compressors on channels 1 to 4 (a fixed 6:1 ratio) tame the loudest voices, and insert jacks on the same channels accept outboard processing. The GigFX engine holds 24 effects, two aux sends feed a monitor mix and the effects bus, and two subgroups with direct outputs help route a panel. Recording is the compromise: the USB interface sends a two-channel mix out and returns four channels at 24-bit/192 kHz, so the podcast is recorded as a stereo mix rather than separate tracks. Waveform OEM software and a plug-in collection are included, and the steel chassis with 60 mm faders suits desks that get moved often.
- Mic preamps: 7 Onyx preamps; up to 60 dB gain each
- Layout: 4 mono mic channels plus mic inputs on 3 stereo channels
- Phantom power: +48 V for all mic inputs, single switch
- Processing: 3-band EQ and 100 Hz low cut on mic channels; compressors on channels 1-4
- Effects: GigFX engine, 24 effects; 2 aux sends; 2 subgroups
- USB: 2-out/4-in at 24-bit/192 kHz (stereo mix recording)
- Dimensions 13 x 3.5 x 17.75 inches; weight 7.9 lb
The ProFX12v3 fits panels that record a finished stereo mix live, with the host balancing voices in real time. Shows that edit each voice separately should take the multitrack Soundcraft or one of the Zoom recorders instead, because a summed mix cannot be unmixed later.
Zoom PodTrak P8
The PodTrak P8 is the only dedicated podcast station in this guide, and it states six mic inputs with XLR connectors and optional phantom power, with up to 70 dB of gain on board for quiet microphones, the highest gain figure published among these six mixers.
That gain matters for podcast panels built on low-output dynamic broadcast microphones. Each mic channel adds a limiter, a low cut filter, tone control and a compressor with a de-esser, plus its own volume slider, mute button and ON AIR indicator; a channel with ON AIR off stays in the headphones but leaves the recording, which suits side conversations during breaks. Six headphone outputs match the six mic inputs one for one, and the unit records up to 13 tracks simultaneously to an SD card in WAV at 44.1 kHz and 16-bit. Nine assignable sound pads with four banks hold 36 clips for intros and ad reads. Remote guests join through a dedicated phone channel or by switching channel 6 to USB mode, both with mix-minus, and an optional Bluetooth adapter adds wireless callers. A 4.3-inch color touchscreen runs the station, which also serves as a 2-in/2-out USB audio interface, and power comes from four AA batteries, the included adapter or USB.
- Mic inputs: 6 XLR with +48 V phantom power; up to 70 dB gain
- Headphone outputs: 6, matching the mic inputs one for one
- Per channel: limiter, low cut, tone control, compressor/de-esser, ON AIR button
- Recording: up to 13 tracks to SD card, WAV 44.1 kHz, 16-bit
- Sound pads: 9 pads, 4 banks, 13 preloaded sounds
- Call-ins: phone channel and USB guest channel, both with mix-minus
- Dimensions 295 x 248 x 61 mm; weight 1.43 kg
Pick the P8 when the show is a podcast first and music never enters the picture: six seats, six headphone feeds and podcast-specific channel tools in the lightest body here. Its 16-bit recording and two-channel USB interface are the limits against the 24-bit multitrack machines.
Yamaha MG12XU
The MG12XU states six D-PRE microphone preamps in a 12-channel console from Yamaha: four mono mic and line channels plus two mono/stereo mic and line channels reach the maker’s stated maximum of 6 mic and 12 line inputs for a full panel of speakers recording at once.
The D-PRE preamps are discrete Class A designs using an inverted Darlington circuit, and the maker’s published figures list an equivalent input noise of -128 dBu and total harmonic distortion of 0.03% at +14 dBu. Mic channels carry +48 V phantom power, a 26 dB pad on the mono inputs and an 80 Hz high-pass filter. One-knob compressors (threshold from +22 dBu to -8 dBu, ratios from 1:1 to 4:1) sit on the input channels, and the three-band EQ works at 10 kHz, 2.5 kHz and 100 Hz with 15 dB of boost or cut. The SPX processor holds 24 effect programs with an optional foot switch for muting effects. Buses run to one stereo bus, two group buses and two aux sends including the effects send, with balanced XLR stereo outputs, monitor and group outputs and a single phones output. Like the Mackie, recording is a stereo affair: the USB interface moves two channels each way at up to 24-bit/192 kHz, and Cubase AI is included as a download. An internal universal power supply and a metal chassis finish a console built for installed and portable PA work as much as podcasting.
- Mic preamps: 6 D-PRE Class A preamps; max 6 mic / 12 line inputs
- Figures: EIN -128 dBu; THD 0.03% at +14 dBu
- Per channel: 1-knob compressor, 3-band EQ, 80 Hz high-pass filter
- Phantom power: +48 V; 26 dB pad on mono inputs
- Effects: SPX processor, 24 programs
- USB: 2-in/2-out at up to 24-bit/192 kHz (stereo mix recording)
- Dimensions 308 x 118 x 422 mm; weight 4.2 kg
The MG12XU suits panels that also need a general-purpose console for events, rehearsals or a small venue, and record a live stereo mix. Podcast-only desks should note the single headphone output: a panel of six needs a separate headphone amplifier that this guide’s Zoom models build in.
Zoom LiveTrak L-8
The LiveTrak L-8 states six independent Zoom preamps in an 8-channel mixer: six combo mic and line inputs plus two line inputs, in a portable body that records every channel while it mixes, with phantom power on the preamps, for location work and live shows.
It records 12 tracks simultaneously and saves a separate file for each input, at up to 24-bit/96 kHz to an SD card, and it can work as a 12-in/4-out USB audio interface at the same time as it records to the card. Four headphone outputs carry three custom monitor mixes plus the main mix, so a host, a producer and guests can hear different balances. Six assignable sound pads with 13 preset sounds handle intros and beds, seven scene memories store mixes for recurring panels, and each channel has three-band EQ and a low-cut function. Remote guests join by phone through the TRRS connection with an included cable, the mix-minus function preventing echo and feedback, or over USB from call applications. Power comes from four AA batteries for up to 2.5 hours, a USB power supply (with automatic switch-over to the AAs if it fails) or the included AC adapter, which makes the L-8 the most location-friendly of the six-preamp models here.
- Mic preamps: 6 independent preamps with phantom power
- Channels: 8 (6 combo mic/line, 2 line)
- Recording: 12 tracks to SD card, up to 24-bit/96 kHz; separate file per input
- USB audio interface: 12-in/4-out, works while recording to SD
- Headphone outputs: 4, with 3 custom monitor mixes plus the main mix
- Sound pads: 6 assignable, 13 preset sounds; 7 scene memories
- Power: 4 AA batteries up to 2.5 hours, USB power or included adapter
Choose the L-8 for six-voice panels that record in varied locations and edit afterward. It gives up the L-12’s extra two preamps, fifth headphone mix and per-channel compressors, so bigger or louder panels should weigh the step up.
Buying guide
Start with the stated preamp count and your real headcount, including the producer or the regular remote guest who sometimes visits in person. Then check the three figures that decide how those preamps behave with your microphones: gain, noise and phantom power arrangement.
Reading mixers for podcasting 5 preamp counts correctly
Count preamps, not channels. A 12-channel mixer may carry only four mic preamps, with the rest of its channels line-only; the models here were admitted only because their pages state the preamp or mic input count directly. Stereo channels can hide extra mic inputs, as on the ProFX12v3, so read the input list rather than the headline channel number.
Gain and noise for quiet microphones
Dynamic microphones need gain, and panels use more of it than solo hosts because guests sit further from their mics. The PodTrak P8 states up to 70 dB, the LiveTrak L-12 and ProFX12v3 up to 60 dB. Noise matters at those settings: the L-12 and MG12XU both publish an equivalent input noise of -128 dBu, the figure to compare when pages provide it.
Phantom power grouping
Panels often mix condenser and dynamic microphones, and the phantom power arrangement decides how flexible that mix is. The LiveTrak L-12 switches +48 V in two groups of four channels, while the ProFX12v3 and MG12XU apply it across the mic inputs. Check your microphone list against the grouping before buying.
Multitrack or stereo mix recording
This is the deepest split in the guide. The Signature 12 MTK, LiveTrak L-12, LiveTrak L-8 and PodTrak P8 record a separate track per voice, which lets an editor fix one panel member at a time. The ProFX12v3 and MG12XU record the stereo mix only, which is faster to publish but locks in every balance decision made during the show.
Headphone feeds for the panel
A six-preamp panel needs six headphone feeds, and only the PodTrak P8 builds in six outputs. The LiveTrak L-12 provides five custom mixes and the L-8 four outputs with three custom mixes. The three analog consoles provide a single phones output each, so budget for a headphone distribution amplifier if your panel records on one of them.
FAQ
Five-preamp shopping raises questions about what counts as a preamp, how much gain a panel needs and whether a stereo mix is enough. The answers below rest on the counts and figures stated on each maker’s product page, the same basis used for the comparison table at the top.
Does a 12-channel mixer always have 12 mic preamps?
No. Channel counts include line-only stereo channels. The mixers here state their preamp counts directly: eight on the Signature 12 MTK and LiveTrak L-12, seven on the ProFX12v3 and six on the PodTrak P8, MG12XU and LiveTrak L-8. Always read the mic input or preamp line in the specifications rather than the channel headline.
Why would a podcast need more than five preamps?
Headcount plus spares. Five preamps seat five voices; the sixth and beyond cover a visiting guest, a producer’s talkback microphone, or a channel kept ready for a phone or playback source. Panels also grow: a show that starts with four hosts and adds a regular fifth voice outgrows a four-preamp unit in one step.
Which mixers for podcasting 5 preamp setups record each voice separately?
Four of the six: the Signature 12 MTK records multitrack over USB, the LiveTrak L-12 and L-8 record multitrack to SD cards, and the PodTrak P8 records up to 13 tracks to a card. The ProFX12v3 and MG12XU record the stereo mix over USB, so voices cannot be separated afterward on those two.
How much preamp gain does a panel of dynamic microphones need?
Look at the stated maximums: up to 70 dB on the PodTrak P8, up to 60 dB on the LiveTrak L-12 and the ProFX12v3’s Onyx preamps. Higher stated gain gives more room for quiet speakers and low-output microphones, and the published noise figure (EIN) tells you how clean that gain is; the L-12 publishes -128 dBu at full gain.
Can these mixers also run live sound or music?
Several are general consoles first: the Signature 12 MTK, ProFX12v3 and MG12XU are live-sound mixers with subgroups, aux sends and effects that podcasters adopt for their preamp counts. The LiveTrak pair mix live while recording. Only the PodTrak P8 is podcast-specific, which shows in its ON AIR buttons and sound pads.
Conclusion
Count preamps on the page, not channels on the box: the Signature 12 MTK and LiveTrak L-12 lead at eight, the ProFX12v3 follows at seven, and the PodTrak P8, MG12XU and LiveTrak L-8 state six each. Match that count to your panel, choose multitrack if you edit, and every voice gets its own clean channel.