Key takeaways
- Compare six mixers for combining audio signals, from passive summing boxes to powered stereo line mixers, on inputs, outputs, gain, noise figures and size.
Running out of inputs is a common small-rig problem: two keyboards, a playback device and a drum machine all need to land on one channel. These six mixers for combining audio signals solve it at line level, summing stereo or mono sources down to one output without a full console anywhere in the chain.
Quick verdict
The six products split into two camps. The Behringer Micromix MX400, the ART SplitMix4 and the Radial MIX 2:1 handle balanced or mono summing jobs in tiny boxes, while the Rolls MX44 Pro, the ART PowerMix III and the Maker Hart Loop Mixer are stereo line mixers with gain, monitoring and several outputs for desktop rigs.
Passive models add no noise of their own and need no power, but they can only turn signals down. Powered models add gain, headphone monitoring and flexible outputs, at the cost of an adapter and a power outlet. The right pick depends on whether your sources are balanced or unbalanced, mono or stereo, and whether the combined feed goes to a console, an interface or a powered speaker.
| Product | Type | Inputs | Best for | Main limit |
|---|---|---|---|---|
| Behringer Micromix MX400 | Powered mono line mixer | 4 x 1/4 inch TS | Sub-mixing mono sources | Mono only, no headphone out |
| Rolls MX44 Pro | Powered stereo line mixer | 4 stereo RCA and 1/8 inch | Playback sources on a desk | Unbalanced inputs only |
| ART SplitMix4 | Passive mixer and splitter | 4 stereo 1/4 inch TRS | Mix or split with no power | Attenuation only, no gain |
| ART PowerMix III | Powered stereo mini mixer | 3 stereo 1/4 inch pairs | Three stereo devices with pan | Only three channels |
| Radial MIX 2:1 | Passive summing mixer | 2 balanced XLR and TRS | Summing two balanced signals | Two inputs, mono output |
| Maker Hart Loop Mixer | Powered stereo line mixer | 5 stereo 3.5 mm | Desktop and streaming setups | 3.5 mm connections only |
How we selected
The entry rule was narrow: the product page had to show a box whose main job is combining several audio signals into fewer outputs, at line level, with level control over each input. Full mixing consoles were left out, because a buyer with this keyword needs a combiner, not a channel strip with EQ and effects.
Each product below was read on its maker or listing page, and every figure quoted comes from that page: input and output counts, connector types, gain, impedance, frequency response, dimensions and weight where the page states them. Where a page does not state a figure, the review says so instead of filling the gap.
The six cover the realistic shapes of the job. There is a mono sub-mixer for keyboards and guitar rigs, two stereo desktop mixers for playback sources, a passive box that can mix or split depending on how it is cabled, a three-channel stereo mixer with pan controls, a balanced two-into-one summing box for studio and stage, and a 3.5 mm desktop mixer built for computers, phones and game consoles.
The six mixers for combining audio signals in detail
Each review starts with what the box combines and how, then covers the controls, the published figures that matter for level matching, and the limits that decide whether it fits a given rig. Prices are not compared here; the differences that matter are signal format, gain and connections.
Behringer Micromix MX400
The MX400 is the plainest tool in this group: a 4-in/1-out mono line mixer that takes four 1/4 inch TS inputs and sends the combined signal to a single 1/4 inch TS output. Each channel has its own input level control, and the maker builds the circuit around ultra low-noise 4580 op amps, with the power supply included in the box.
That simplicity is the point. Keyboard players use it to sub-mix several mono synth outputs before they reach the main console, and guitar rigs use it to fold multiple mono sources into one amp or one interface input. Because every input and the output are unbalanced TS connections, cable runs should stay short, and there is no headphone output for checking the mix in isolation.
The listing page does not state dimensions or weight, so neither is quoted here. What the page does make clear is the signal shape: mono in, mono out. A stereo source needs two channels of the four, one for each side, which halves the practical input count for stereo work.
- Pros: four level-controlled mono inputs in a very small box; power supply included; simple one-job design.
- Cons: mono only; unbalanced connections; no headphone monitoring.
- Buy if: you need to combine mono line sources into one feed. Skip if: your sources are stereo or balanced.
Rolls MX44 Pro
The MX44 Pro mixes up to four stereo line-level signals, such as CD players, DVD players, MP3 players, laptops and smartphones, down to a single stereo output. Every channel offers both a pair of RCA jacks and a stereo 1/8 inch input, and the output side mirrors that with stereo RCA and a stereo 1/8 inch jack that also works as a headphone output.
Each channel’s level knob provides up to 30 dB of gain, so quiet phone and laptop outputs can be lifted to match louder players. The maker lists a frequency response of 20 Hz to 30 kHz and a signal-to-noise ratio of 85 dB, with input impedance of 10 kOhms and output impedance of 100 Ohms. The steel chassis measures 4.5 x 1.5 x 4.0 inches and the unit weighs 1.0 lb.
Power is flexible: the mixer runs from a 9V battery or from DC power, and an adapter is included. All inputs are unbalanced, so this is a desktop and playback box rather than a stage box for long cable runs. For a media corner, a classroom or a small studio playback chain, that trade is usually the right one.
- Pros: four stereo channels with real gain; battery or DC power; headphone-capable output.
- Cons: unbalanced RCA and 1/8 inch connections only; no balanced output for long runs.
- Buy if: your sources are players, laptops and phones. Skip if: you need balanced lines or mic inputs.
ART SplitMix4
The SplitMix4 is a four-channel line mixer, splitter and level attenuator in one passive box. The maker describes three ways to cable it: mix four inputs down to one output, split one input to four outputs, or run four stereo sources through independent level attenuators to their own stereo outputs, or any combination of those layouts.
All connections are 1/4 inch stereo TRS with intelligent switching: plugging into a mix input removes that channel from the splitter bus, and plugging into a splitter output removes it from the mix bus. Mono or stereo operation is decided by the cable you connect. Independent stereo level controls are provided on each channel, with over 90 dB of attenuation available.
Because the design is fully passive, there is no active circuitry to add noise or distortion and no power supply to carry. The maker lists input impedance of 25 k to 100 k ohms, output impedance of 1 k to 4 k ohms, frequency response of 20 Hz to 20 kHz within +/-1 dB, and THD under 0.005 percent at 1 kHz as a typical figure. The box measures 1.85 x 4.6 x 4.1 inches and weighs 0.84 lb. The limit is built into the concept: a passive mixer can only turn signals down, never up.
- Pros: mixes, splits or attenuates with no power at all; balanced TRS connections; very small and light.
- Cons: no gain on any channel; combined output level depends on source levels.
- Buy if: your sources are strong line-level signals. Skip if: any source needs boosting to be heard.
ART PowerMix III
The PowerMix III answers a narrower question: how to connect a CD player, a synthesizer and the line output from a bass amp to one destination. It has three input channels, each with its own pan and level controls, and it accepts either mono or stereo signals, mixing them down to stereo or to identical left and right mono signals.
Inputs are three sets of 1/4 inch left and right unbalanced jacks. The published figures list maximum gain of +27 dB, input impedance of 10k ohms, maximum input level of +30 dB and maximum output level of +13 dB, with output impedance of 100 ohms. A headphone output with its own level control lets you check the combined feed before it goes anywhere else.
The unit runs on 12V DC with the adapter included, measures 5.625 x 3.75 x 1.75 inches and weighs 1.3 lb. Three channels is the ceiling, and the connections are unbalanced, so it suits short desktop and keyboard-rig runs. Within that shape, the pan controls are the feature the other small boxes here do not offer: each source can be placed in the stereo field, not just leveled.
- Pros: pan and level on every channel; headphone output with its own control; healthy +27 dB maximum gain.
- Cons: only three channels; unbalanced inputs and outputs.
- Buy if: three stereo sources need combining with placement control. Skip if: you need four or more sources.
Radial MIX 2:1
The MIX 2:1 does one job: it passively sums two audio channels down to one mono output on a single XLR connector. The maker lists the standard uses: summing the stereo outputs of a console, a recording interface or a playback device to mono, or mixing any two signals together while balancing their relative input levels.
Both inputs accept balanced 1/4 inch TRS and XLR connectors, and the box works with mic-level signals as well as line level, so two dynamic microphones can be mixed into a single preamp input when channels run short. Ground lift switches on the inputs address buzz and hum from ground loops, and a 180-degree phase flip helps keep two inputs phase coherent, for example two microphones on one guitar amplifier.
Each input has a trim control that can be attenuated to match levels, and the level controls can be bypassed entirely to sum both channels at unity gain. The circuit is completely passive, so no power is required. The opened page does not state dimensions or weight. The maker notes that phantom power must be disengaged when the MIX 2:1 feeds a microphone preamp, a working detail worth knowing before it is cabled into a live rig.
- Pros: balanced inputs for mic or line signals; ground lift and phase flip on board; no power needed.
- Cons: only two inputs and a mono output; trim only, no gain.
- Buy if: two balanced signals must become one. Skip if: you need stereo output or more inputs.
Maker Hart Loop Mixer
The Loop Mixer is the desktop entry: five stereo inputs and three outputs, all on 3.5 mm jacks, so headphones, speakers and a REC OUT can all be fed at the same time. The listing describes it as a way to mix different sounds into one for musicians, gamers, podcasters and live streamers working with smartphones, music players and game consoles.
An included DM2S adapter combines two mono 6.35 mm inputs into one stereo 3.5 mm plug, so the five stereo inputs can take up to ten mono devices between them. Each input has balance, gain and volume controls, plus a master volume control. The maker rates the gain boost at up to 50 dB per input across the line-to-mic range, and a built-in signal overload indicator shows when an input is driven too hard.
Up to five Loop Mixers can be chained with a LOOP BUS cable, sold separately, so several people can hear the same mix and adjust their own volume. The box measures 5.12 x 6.89 x 1.18 inches and weighs 15.84 ounces, and it runs from a 9V adapter. Every connection is 3.5 mm, which is exactly right for phones and consoles and exactly wrong for balanced stage gear.
- Pros: five stereo inputs with three simultaneous outputs; per-input gain up to 50 dB; chainable design.
- Cons: 3.5 mm unbalanced connections only; adapter cables needed for 1/4 inch gear.
- Buy if: your sources live on a desk with 3.5 mm outputs. Skip if: your rig uses XLR or balanced lines.
Buying guide
Combining signals is simple in concept and specific in practice. The five checks below cover the decisions that separate a box that solves the problem from one that almost does: signal format, gain, connector type, output count and where the combined feed goes next in the chain after the mixer.
Decide between passive and powered designs
A passive combiner has no active circuitry and no power supply; it can only attenuate. That is enough when every source is a strong line-level output, and it keeps the noise floor at whatever the sources produce. A powered mixer adds gain, which quiet sources such as phones and laptops often need before they can match louder players in the mix.
The SplitMix4 and the MIX 2:1 in this guide are passive; the other four are powered. If one of your sources is clearly quieter than the rest, a passive box forces you to turn everything else down to match it, and the whole mix arrives at the next device at a lower level. If all sources are healthy line-level signals, passive is simpler and needs no outlet.
What to check before choosing mixers for combining audio signals
Start with a count and a format. Count the sources you combine today and likely additions, then note whether each is mono or stereo and balanced or unbalanced. A stereo source eats two channels on a mono mixer, and an unbalanced source on a long cable run invites hum, so the format answers matter as much as the channel count on the panel.
Then look at the destination. A console input, an audio interface, a powered speaker and a recorder all accept the combined feed happily, but they differ in the level they expect. Published figures such as maximum output level and output impedance, quoted in the reviews above where the maker states them, tell you whether the pairing is sensible before you buy.
Match connectors to your sources
The six products here use four connector families: 1/4 inch TS on the MX400, RCA and 1/8 inch on the MX44 Pro, 1/4 inch TRS on the SplitMix4, XLR and TRS on the MIX 2:1, and 3.5 mm throughout the Loop Mixer. Every adapter between a source and the mixer is another joint in the chain, so the best connector set is the one your sources already use.
Balanced connections, on the SplitMix4 and the MIX 2:1, reject interference picked up along the cable, which matters on stage and in larger rooms. Unbalanced connections are fine across a desk. If your sources are a phone, a laptop and a game console, the Loop Mixer’s 3.5 mm jacks need no adapters at all; if they are synths with 1/4 inch outputs, the MX400 or PowerMix III is the direct fit.
Check gain and headroom figures
Gain decides whether quiet sources can sit level with loud ones. In this group the published numbers run from no gain at all on the passive boxes, through up to 30 dB per channel on the MX44 Pro and +27 dB maximum on the PowerMix III, up to 50 dB per input on the Loop Mixer, which is built to lift mic-level signals as well as line sources.
Maximum input level matters at the other end of the scale: the PowerMix III lists +30 dB, which is room for hot synth and player outputs. An overload indicator, fitted to the Loop Mixer, is the practical version of the same information while you work. Where a maker does not publish a figure, the reviews above say so rather than guessing at it.
Plan the outputs, not just the inputs
Combining is only half the job; the combined feed often needs to reach more than one place. The Loop Mixer feeds headphones, speakers and a record output. The MX44 Pro’s 1/8 inch output doubles as a headphone jack. The PowerMix III has a headphone output with a level control. The mono boxes send one feed to one destination, all a sub-mix needs.
Think about monitoring while you decide. If the combined feed goes straight to a recorder or a stream, a headphone output on the mixer is how you hear problems before the audience does. If it goes to a console with its own monitoring, a single output is enough and the simpler box is the better buy.
FAQ
Most questions about combining signals come down to format and level: what happens to stereo, what happens to volume, and what a passive box can and cannot do. The answers below stick to what the makers of the six products above publish about their own boxes and to general signal practice.
Do passive mixers for combining audio signals lose volume?
Yes. Level loss is part of how a passive mixer works: with no active circuitry, the box can only turn signals down, and summing itself costs level. The SplitMix4 offers over 90 dB of attenuation range on its level controls, and the MIX 2:1 lets you bypass its trims to sum at unity gain when both sources are already matched.
In practice the loss is manageable when sources are strong line-level outputs feeding a console or interface input with gain of its own. It becomes a problem when a source is already quiet, such as a phone at low volume. In that case a powered mixer with per-channel gain, like the MX44 Pro or the Loop Mixer, is the better tool for the same job.
Can I combine two microphones with one of these boxes?
One product here is built for it: the Radial MIX 2:1 takes balanced mic-level signals on XLR and TRS inputs and can mix two dynamic microphones into one preamp input. Its maker notes phantom power must be off when it feeds a microphone preamp, and its ground lift and phase flip switches address the problems that come with pairing microphones.
The Loop Mixer also lifts low-level signals, with gain rated up to 50 dB per input across its line-to-mic range, but its inputs are 3.5 mm, so microphones need adapters. The other four products are line-level boxes; a microphone plugged into them without a preamp will be far too quiet to use.
Why not just use a Y cable to combine signals?
A Y cable joins two outputs directly, so each output drives the other as well as the destination. That can distort, drop levels unevenly and stress output stages. A mixer, even a passive one, puts resistance or active circuitry between the sources so each one sees a proper load and the levels can be balanced against each other with a control.
The difference shows up in control as much as in protection. Every product in this guide gives each input its own level control, which a cable cannot do. When two sources differ in loudness, and they almost always do, the level controls are what turn a combined feed into a listenable mix.
Does combining stereo sources into mono cause problems?
It can change the sound. Sounds out of phase between the left and right channels partly cancel when summed to mono, which is why the MIX 2:1 carries a 180-degree phase flip for its two inputs. Material mixed for stereo playback usually survives well; heavily widened or chorused sources are the ones that can thin out when folded together.
If the destination is a single powered speaker or a mono PA, summing is unavoidable and a dedicated box does it in a controlled way. The MX400 sums to mono by design. If the destination can take stereo, a stereo combiner such as the MX44 Pro or the SplitMix4 keeps the image intact and avoids the question entirely.
How many inputs do I need for a small keyboard rig?
Count stereo pairs, not devices. One stereo keyboard uses two mono channels or one stereo channel. Two keyboards plus a playback device need six mono channels or three stereo ones, which is the PowerMix III’s three stereo channels or two MX400s, one for each side. The Loop Mixer covers five stereo sources on 3.5 mm for module and groovebox rigs.
Leave one input spare if you can. Rigs grow, and a combiner bought exactly at today’s count is the one that gets replaced first. The exception is a fixed two-source job, such as summing a stereo source to mono for one speaker, where the two-input MIX 2:1 is the complete answer.
Conclusion
For balanced two-signal summing, the Radial MIX 2:1 is the firm pick; for stereo desktop sources, the Rolls MX44 Pro; for keyboard sub-mixing, the Behringer Micromix MX400. The ART pair and the Maker Hart Loop Mixer cover passive splitting and 3.5 mm rigs. Match format and gain first, and the combined feed will behave.