Key takeaways
- Five DJ mixers for vinyl compared: Xone:96, DJM-V10, DJM-A9, Xone:43, and RMX-60 Digital, checked by phono inputs, EQ style, filters, DVS support and faders.
Playing records makes demands a digital setup never does, and the dj mixers for vinyl gathered here all answer the first one: proper phono inputs with RIAA equalization for turntables. Beyond that, they split into analog and digital designs with very different ideas about EQ, filters, and effects, both in clubs and at home.
What vinyl asks from a DJ mixer
A turntable’s cartridge puts out a tiny signal that needs a dedicated phono stage to raise it to line level and apply RIAA equalization. A mixer built for vinyl provides that stage on the channels you will use for decks, plus the grounding, EQ, and cueing tools that record mixing relies on.
Phono inputs, RIAA stages, and ground terminals
Count the phono inputs before anything else. Two turntables need two phono inputs; a four-deck setup or a pair of decks plus DVS control vinyl needs four. Every mixer in this guide states its phono count on its product page, and the spread runs from two phono inputs on the Reloop RMX-60 Digital to four on the Xone:96, DJM-A9, and DJM-V10.
Grounding is the quiet detail that decides whether a vinyl set hums. Turntables connect a ground wire to the mixer, and the Xone:96 provides two earth ground terminals on its rear panel for exactly that job. Signal quality on the phono path matters too: both Pioneer flagships here rate their phono inputs at an 88 dB signal-to-noise ratio, a figure the makers publish for the phono stage specifically.
Switchable inputs add flexibility. The Xone:96’s channels carry an LN/PH switch marked for DVS, so the same channel can take a turntable or a line source, and the RMX-60’s two phono inputs sit among eleven total inputs, letting CDJs or media players fill the remaining channels while the turntables stay patched in.
EQ and filters for blending records
Vinyl mixing is long-blend mixing, and the EQ decides how much control you have while two records run together. Three-band EQ with full cut, often called total kill or isolator EQ, lets you remove a record’s bass completely before swapping it for the incoming track’s low end, which is the core move of house and techno mixing.
Four-band EQ goes further. The Xone:96 gives its four main channels a 4-band EQ, and the DJM-V10’s 4-band channel EQ splits the mids into two ranges, rated at -26 dB to +6 dB each, with the high and low bands cutting all the way down. Filters are the second blending tool: the Xone family’s VCF filters sweep a channel’s frequency range with resonance, the Xone:96 offering two of them with high-pass, band-pass, and low-pass modes, while the RMX-60 puts a bipolar filter pot under each channel’s EQ.
Isolator-style master sections appear on the digital flagships. The DJM-V10 adds a 3-band master isolator with boost and cut up to +9 dB per band for whole-mix moves, and the DJM-A9’s channel isolators are paired with Sound Color FX that include a center lock function, which stops the effect at its middle position so a sweep cannot run past the point you intended.
Soundcards and DVS for control vinyl
Many vinyl DJs also play control vinyl, using timecode records to steer digital files. That needs a USB soundcard in the mixer and software support, and the five models here split sharply: some carry large soundcards, and two carry none at all, which is a deliberate analog choice rather than a missing feature.
The Xone:96 carries dual 32-bit/96kHz USB soundcards, each with six stereo inputs and outputs, and supports Traktor Scratch DVS from the box. The DJM-V10’s integrated soundcard handles up to six stereo channels of 32-bit/96 kHz audio with 64-bit internal processing, with DVS support listed for rekordbox, Serato DJ Pro, and Traktor. The DJM-A9 works with rekordbox and Serato DJ Pro over its dual USB connections, which mix USB Type-B and USB Type-C ports, so a laptop changeover does not depend on one cable type.
At the other end, the Xone:43’s listed features include no USB soundcard, and the RMX-60 Digital’s spec sheet states plainly that it has no USB audio interface; its USB port is a service port for firmware updates. Vinyl purists lose nothing with either, but DVS players must add an external interface to those two mixers.
The five dj mixers for vinyl in detail
Each mixer below was checked on its maker’s or a detailed product page, and the figures quoted are the ones those pages publish: phono and line input counts, EQ ranges where stated, soundcard formats, fader types, and the dimensions and weight of the unit itself.
Allen & Heath Xone:96
The Xone:96 is an analog mixer with digital connectivity layered on top: six plus two channels, four of them main stereo channels with phono inputs on RCA, an LN/PH switch for DVS, and the 4-band Xone EQ. Two further stereo channels carry 3-band parametric EQ for external sources and effects returns.
For vinyl, the details line up well. Four phono inputs take four turntables, two earth ground terminals handle their ground wires, and the published headroom is 20 dB. The dual Xone:VCF filters offer high-pass, band-pass, and low-pass modes with adjustable frequency and resonance, assignable across the channels, and a CRUNCH circuit adds controlled harmonic distortion before filtering for a rougher edge on a blend.
The dual USB soundcards are the bridge to digital: two independent 32-bit/96kHz interfaces, each 12 in and 12 out, allow dual-laptop sets and DVS with Traktor Scratch Pro. Hardware includes 60mm VCA channel faders, a replaceable InnoFADER crossfader with three curve types, two sends and four returns plus a master insert for outboard gear, and two independent headphone cue systems for back-to-back sets. The mixer measures 336 x 410 x 109 mm and weighs 7 kg (15.4 lb).
Two smaller details suit hybrid rigs: X-Link connectivity supports Xone:K-series controllers without taking another computer USB port, MIDI runs over USB and a five-pin DIN output, and a 3.5mm sync output connects compatible compact synthesisers, so a record set can grow drum machines and live electronics around the turntables.
Pioneer DJ DJM-V10
The DJM-V10 is Pioneer’s six-channel creative flagship, and its input list is the longest here: four phono inputs for turntables, six line inputs, and six digital coaxial inputs across six channels, plus two microphone inputs. A vinyl DJ can run four decks and still have channels left for samplers, synths, or drum machines.
Each channel carries a 4-band EQ whose high and low bands cut fully and boost to +6 dB, while the two mid bands run from -26 dB to +6 dB, and each channel also gets a compressor knob, intended to help older or unmastered tracks sit alongside modern productions. A dedicated high-pass or low-pass filter with resonance sits on every channel, and a 3-band master isolator shapes the whole mix.
The send section offers four built-in effects, Short Delay, Long Delay, Dub Echo, and Reverb, plus two external send-and-return loops for pedals and studio processors, while the Beat FX section works from a touchscreen and adds a Shimmer effect. Conversion is 32-bit at a 96 kHz sample rate with 64-bit internal processing, the phono signal-to-noise ratio is rated at 88 dB, and DVS support covers rekordbox, Serato, and Traktor. Two independent headphone outputs, booth EQ, and an AES/EBU master output complete a unit measuring 43.8 x 46.7 x 10.8 cm and weighing 11.9 kg (26.2 lb). A locking power cord is included, which helps prevent accidental disconnection in a crowded booth.
Pioneer DJ DJM-A9
The DJM-A9 is the four-channel club standard in this group: four phono inputs on RCA, four line inputs, four digital coaxial inputs, and two microphone inputs, one of them now with phantom power for condenser microphones, a two-band mic EQ, and mic effects.
Sound runs through ESS Technology 32-bit A/D and D/A converters, with a phono signal-to-noise ratio of 88 dB, line at 105 dB, and total harmonic distortion of 0.005 percent on the line path. The third-generation MAGVEL FADER crossfader handles the cuts, and the channel section’s isolators have an adjusted frequency response for more precise control.
The performance tools are Pioneer’s current set: six Sound Color FX, including Space, Dub Echo, Crush, Sweep, Noise, and Filter, with the center lock function that stops the effect at its middle detent, and a Beat FX section with its own color display and X-Pad. Dual independent headphone outputs, each with its own cue and level controls, suit back-to-back sets, and Bluetooth input plus Wi-Fi for the Stagehand app cover the wireless side. It measures 407.4 x 458.3 x 107.9 mm and weighs 10.2 kg (22.5 lb), and it works with rekordbox and Serato DJ Pro.
The wireless side has a practical side for vinyl DJs: the Bluetooth input accepts audio from a phone for requests or reference tracks without repatching a channel, and the Wi-Fi link lets the Stagehand app check the status of connected gear and run its built-in Sound Check function before the room fills.
Allen & Heath Xone:43
The Xone:43 is the purist’s option: a 4+1 channel analog mixer with four channels of phono/line input and a separate mic/aux channel, so a microphone never has to steal a deck channel. There is no soundcard and no onboard effect engine; the sound-shaping tools are the filter and the EQ, and both are strong.
The analogue VCF filter system offers low-pass and high-pass filters with a frequency sweep and resonance that runs, in the maker’s words, from mild to wild, and an external effects loop routes through the filter system with per-channel dry/wet blend controls. The 3-band total kill EQ on all four channels can eliminate a frequency band completely and bring it back with a twist, which is the classic Xone approach to long blends.
Supporting details include 20 dB of headroom, 9-segment signal level metering, 3.5mm and 1/4-inch headphone outputs, and an X:Link port for Xone:K series controllers. The crossfader can be swapped for a custom Innofader, a common upgrade among scratch and blend DJs alike. For a two-turntable setup that will never touch a laptop, this is the most direct signal path in the guide.
Reloop RMX-60 Digital
The RMX-60 Digital is a 4+1 channel digital club mixer with eleven inputs and six outputs. For vinyl its input list is the shortest here, two phono inputs alongside seven line inputs and a combo microphone input, so it suits the classic two-turntable setup with media players or CDJs filling the other channels.
Its EQ section is switchable per the maker’s two characteristics: Classic mode runs +12 dB to -8 dB, and Isolator mode runs +12 dB to -26 dB with total kill behavior, and a bipolar filter pot sits under the three-band EQ on each channel. Eight performance effects, including delay, echo, reverb, gate, pitch shift, and bit crusher, can be routed to individual channels, the microphone, or the master output, with an LCD display and a double BPM counter for beat and effect parameters.
Fader curves for line faders and the crossfader are adjustable, the crossfader is freely assignable and InnoFader compatible, and the mic channel adds a 2-band EQ with Active Ducking talkover. Two headphone outputs and balanced XLR plus RCA outputs round out the panel. It measures 320 x 107.5 x 386.7 mm and weighs 6.8 kg, and its USB port serves firmware updates rather than audio, so DVS players need an external interface.
Two smaller features round out the RMX-60 for working DJs. Fader start can trigger a connected player as a channel fader opens, and the crossfader start works the same way from the crossfader, which suits quick cue drops without a free hand. The headphone section uses an intelligent one-knob equalizer with a mono/stereo switch, so a cue feed can be checked in mono for phase problems or opened up in stereo for detail. Together with the switchable EQ curves, these are the touches that make the mixer feel like a club tool rather than a home unit, even though its two phono inputs keep it aimed at two-deck vinyl rigs.
Comparing dj mixers for vinyl side by side
The table collects the figures that decide a vinyl setup: how many turntables each mixer takes, whether the signal path is analog or digital, what EQ it offers, and whether a soundcard is built in. Everything in it comes from the product pages behind the notes above.
| Model | Phono inputs | Channels | Design | EQ | USB soundcard |
|---|---|---|---|---|---|
| Allen & Heath Xone:96 | 4 | 6 + 2 | Analog | 4-band + 3-band parametric | Dual, 32-bit/96kHz |
| Pioneer DJ DJM-V10 | 4 | 6 | Digital | 4-band + master isolator | Yes, 96 kHz |
| Pioneer DJ DJM-A9 | 4 | 4 | Digital | Isolator EQ | Yes, dual USB |
| Allen & Heath Xone:43 | 4 | 4 + 1 | Analog | 3-band total kill | None |
| Reloop RMX-60 Digital | 2 | 4 + 1 | Digital | 3-band, Classic/Isolator | None |
Analog purity versus digital features
The two Allen & Heath mixers keep the audio path analog end to end, which vinyl traditionalists prefer: the record’s signal is never converted, and the VCF filters work as analog circuits. The Xone:96 then adds digital only at the edges, with its dual soundcards for recording and DVS, so the mix itself stays analog.
The Pioneer and Reloop models convert the phono signal and mix digitally, which buys the effects, compressors, and displays. The published phono signal-to-noise figures show the cost is small on paper: 88 dB on both Pioneer flagships. The RMX-60’s maker does not publish a phono noise figure on the pages checked, so its digital path is judged by its 20 Hz to 20 kHz frequency range and its feature set instead.
Faders, crossfaders, and cue systems
Blend DJs live on the channel faders, and the Xone:96’s 60mm VCA faders are the longest travel here, while the DJM-V10 uses newly developed channel faders the maker describes as precise and durable, and the DJM-A9 relies on its third-generation MAGVEL FADER crossfader for cuts.
The RMX-60 and Xone:43 both accept replacement Innofader crossfaders, the Xone:43 as a custom upgrade and the RMX-60 by design.
Cue systems decide how well two DJs share a mixer. The Xone:96 and DJM-V10 both provide two independent headphone cue systems, and the DJM-A9 provides dual headphone outputs with separate controls, so back-to-back partners can each prepare a record without disturbing the other’s monitoring. The Xone:43 and RMX-60 offer the standard single cue system with both headphone jack sizes.
Choosing among dj mixers for vinyl
Start with the deck count and the role of the laptop. Four turntables, or two decks plus control vinyl and a sampler, point to the six-channel models. A strict two-deck analog rig points the other way. Then weigh the EQ style you actually mix with, because you will touch it on every transition.
Two turntables at home
A home two-deck setup is where the Xone:43 and RMX-60 Digital make their case. The Xone:43 gives the analog filter-and-kill-EQ experience with a mic channel to spare and nothing digital in the path, while the RMX-60 trades two of the phono inputs for built-in effects, a BPM counter display, and switchable EQ curves at a similar footprint.
Both leave room to grow in different directions: the Xone:43 through its effects loop and X:Link controllers, the RMX-60 through its extra line inputs for media players. Neither records to a computer by itself, so home DJs who archive every set should budget for an interface or step up to a soundcard model.
Four-deck and hybrid club setups
Four-deck and hybrid setups belong to the Xone:96, DJM-V10, and DJM-A9. All three take four phono inputs; the Xone:96 adds its parametric-EQ return channels and master insert for hardware-heavy rigs, and the DJM-A9 keeps the familiar four-channel club layout with the newest Pioneer effects.
The V10 adds two more channels beyond that, plus per-channel compression for mixing records with unmastered digital files.
Changeovers matter in clubs, and all three handle them: dual soundcards or dual USB connections let two laptops stay connected, and dual headphone systems let the incoming DJ cue up while the outgoing DJ finishes. The V10’s AES/EBU master output suits large venues with long cable runs to the house system.
Recording and streaming a vinyl set
Recording a set is easiest on the soundcard models. The Xone:96’s dual 12-in/12-out interfaces can send the mix or individual channels to a computer, and the DJM-V10 routes channel, send, and master signals over USB and can record to its maker’s phone app through the MULTI I/O terminal.
The DJM-A9’s USB connections serve the same purpose through its software partners.
On the Xone:43 and RMX-60, use the analog record outputs instead: both provide record outs (the Xone:43’s is a pre-level mix output on RCA), which feed any small USB interface or portable recorder. The quality ceiling is set by that external device, but the workflow is simple and keeps the analog chain untouched.
Setup checks for turntables and mixers
Most vinyl problems blamed on mixers are setup problems: a missing ground wire, a channel switched to line instead of phono, or gain staged so hot that the phono stage clips. A ten-minute check with one familiar record, played on each deck in turn, catches nearly all of them before a set starts.
Grounding, hum, and gain staging
Connect each turntable’s ground wire to the mixer’s ground terminal; the Xone:96 provides two for its four phono channels. If a hum remains, check that the cartridge headshell contacts are clean and that the RCA plugs seat fully, then confirm the channel selector actually points at the phono input rather than the line input sharing the channel.
Set gains with the loudest record you own. The phono stage’s job is to bring the cartridge up to the same working level as a line source, and the mixers here publish generous headroom figures, 20 dB on both Allen & Heath models, so aim for peaks in the upper part of the channel meter without holding the top segment lit.
Needle, cartridge, and input level checks
A worn stylus sounds like a bad phono stage: dull highs, distortion on loud passages, and mistracking on heavy bass. Swap the stylus or the deck before blaming the mixer, and compare the same record on a second phono input if the mixer has one, since a fault that follows the deck is in the deck.
Finally, match the two decks’ levels. Play the same record on both turntables and set the channel gains so the meters agree; after that, your EQ and fader moves behave the same on either side, which is what makes a long blend predictable.
Conclusion
For analog sound with modern routing, the Xone:96 leads; for channel count and processing, the DJM-V10; for the current club standard, the DJM-A9. The Xone:43 keeps vinyl purely analog, and the RMX-60 Digital covers two decks with effects built in. Count the phono inputs first, then choose the signal path that matches how you actually play.