Updated Nov 15, 2026· 17 min read

Key takeaways

  • Compare compact cooktops for sprinter conversion galleys: two-burner gas, propane and induction models with listed dimensions, burner output and power needs.

A van galley gives a cooktop very little room, a limited power supply and a counter that doubles as prep space, so household units rarely fit. This guide compares compact cooktops for sprinter conversion projects, using the dimensions, burner output and fuel or voltage figures each maker publishes for two-burner models.

Quick verdict

Short on time? The six models below split into three clear camps: propane drop-ins built for vehicle galleys, a natural gas domino that converts to LP, and two induction units that trade fuel plumbing for a serious electrical allowance. Start with the fuel decision, then match the cutout.

Product Type Best for Key spec Main limit
Kenyon Bridge Induction 2 Burner Portrait Induction, built-in Electric-only builds with strong inverter capacity Two 6.25 inch burners, 120 volt boost up to 1500 watts Maker page does not render overall dimensions
Empava IDC12B2 Induction, drop-in Plug-in simplicity on a 120 volt system 1800 watt and 1300 watt burners, plug pre-installed Needs a 20 amp circuit and shares 1800 watts total
Suburban SDN2U Gas drop-in Traditional RV-style propane galleys Two burners at 6,500 BTU per hour each Match ignition, no spark starter
Furrion FGH12D2-BL Gas slide-in Narrow counters that need a folding cover 8,000 BTU front and 6,500 BTU rear burners Long 22 3/4 inch depth eats counter run
Dometic PI8022 Gas hob with lid Lightweight builds watching every kilogram 3.58 kg net weight, 1.1 and 1.8 kilowatt burners Spec sheet is a non-US market document
Summit GC2BGL Gas-on-glass domino Household-style fit and finish in a 12 inch width 8,350 BTU and 3,400 BTU sealed burners Preset for natural gas, conversion needed for LP

How we selected

Selection started with footprint: every model here is a two-burner unit in a compact width or a vehicle galley format, because a Sprinter counter run cannot spare the depth of a household four-burner top. Published dimensions, burner output and fuel or voltage data then decided the places.

Priority went to makers that publish a full specification sheet: exact width, depth and height, a cutout size where one is offered, burner output in BTU, watts or kilowatts, and the fuel or electrical input in plain terms. Models with thin or missing data were left out, because a conversion is planned on paper long before the counter is cut.

Fuel mix was deliberate. Propane remains the default in van galleys, so three of the six picks burn gas and one more converts to LP with an included kit. The two induction models represent the all-electric build, with voltage and wattage stated plainly enough to size an inverter against them. No model here is described as approved for a specific vehicle, because no maker page read for this guide makes that claim for the Sprinter.

Six cooktops for sprinter conversion galleys

The six picks below are ordered by fuel and format rather than by a single winner, because the right answer in a van depends on the systems already in the build. Each entry gives the listed size, output and input first, then the trade-offs that matter once the unit is living in a small galley full time.

Kenyon Bridge Induction 2 Burner Portrait

Kenyon builds this two-burner induction unit in a portrait layout, with the burners stacked front to back instead of side by side, which suits narrow van counters. It is the pick for an all-electric conversion that already carries a large battery bank and inverter for other loads.

The maker lists two 6.25 inch burners under a smooth black glass top, with slide touch controls and a bridge function that links both burners into one larger zone for a griddle or an oversized pan. Boost output is listed at up to 1500 watts on the 120 volt models, up to 2000 watts on the 240 volt P2 models and up to 2100 watts on the 240 volt P3 and P4 models, with boost lasting up to 10 minutes.

Power sharing is the feature that matters most in a van: the maker says the cooktop distributes power across the active zones so the unit maximum rated wattage is not exceeded, which makes the load easier to plan against an inverter rating. The included SilKEN mat covers the cooking area, and the maker says it helps keep pots in place, protects the glass and can be rinsed in the sink or put in the dishwasher.

Limits are real. The maker page read for this guide does not render the overall dimensions or weight in its specifications table, so a builder must get the exact footprint from the maker before cutting a counter. Induction also needs magnetic cookware, and even the 120 volt version draws boost power a small inverter will not sustain. Buy it for a portrait counter run and a strong electrical system; skip it if the build runs on propane alone.

  • Pros: portrait layout fits narrow counters; bridge zone handles griddles; power sharing caps the electrical load
  • Cons: dimensions not stated on the page read; needs magnetic pans; boost draw is heavy for small inverters
  • Buy if: the conversion is all-electric with a generously sized inverter
  • Skip if: the galley plan is propane only

Empava IDC12B2 12 inch compact induction cooktop

The Empava IDC12B2 is the simpler induction route: a 12 inch class drop-in with a pre-installed 120 volt plug, so it can run from shore power or a suitable inverter without hardwiring. It suits converters who want induction without planning a 240 volt circuit.

The listing gives full dimensions: 20.5 inches long, 14.12 inches deep and 2.12 inches high, with a cutout of 19.5 by 13.5 inches. The left burner offers 8 power levels from 300 watts to 1800 watts, the right burner 6 levels from 300 watts to 1300 watts, and the two share power when both run. Nine temperature settings run from 120 degrees F to 460 degrees F, and a timer runs from 1 to 179 minutes with automatic shutoff.

Everyday details are listed plainly: a hot surface indicator shows the letter H, a sensor turns an element off when no pan is present, and a child control lock keeps the controls from being switched on by accident. The listing states ETL certification and a 2 year manufacturer warranty. The electrical requirement is printed as 120 volts and 20 amps, the number to check against the van system first.

The limit is arithmetic: 1800 watts is the whole allowance, shared between burners, so a fast boil and a simmering pot divide that output between them. The 20 amp requirement also rules out smaller inverters. Buy it for plug-in induction on a healthy 120 volt system; skip it if two full-power burners at once are a daily need.

  • Pros: plug pre-installed; full dimensions and cutout published; temperature and timer control
  • Cons: 1800 watt total shared across both burners; needs a 20 amp supply
  • Buy if: the build has shore power or a strong inverter and cooks one main dish at a time
  • Skip if: parallel high-heat cooking is the norm

Suburban SDN2U 2 burner drop-in cooktop

Suburban is a long-standing RV appliance maker, and the SDN2U is its straightforward two-burner drop-in: porcelain top, match ignition and optional covers. It fits conversions that follow the classic propane galley pattern used in travel trailers and motor homes.

The maker spec sheet lists two burners at 6,500 BTU per hour each, a maximum inlet pressure of 13 inches W.C. and a manifold pressure of 10 inches W.C. Clearances are printed in full: 18 inches vertical, 8 inches at the back and 6.0 inches on each side as the minimum distance to combustibles, which gives a builder real numbers for the cabinet design around the unit.

Finish choices are black or stainless steel porcelain, and the accessory list is practical for a van: covers with or without side shields, plus flush mount clear or black glass covers that turn the cooktop back into counter space when the burners are cold. The maker lists a 2 year limited warranty.

The trade-off is convenience. Ignition is by match, so there is no spark starter, and the spec sheet text references the cutout drawing without printing an overall width and depth in numbers, so the cutout must be taken from the maker drawing during the build. Buy it for a proven RV pattern and printed clearances; skip it if push-button ignition is a must.

  • Pros: clearances and pressures published; cover options restore counter space; 2 year limited warranty
  • Cons: match ignition only; overall size not printed in the sheet text
  • Buy if: the conversion follows a standard propane RV galley layout
  • Skip if: spark ignition and a big boil burner are priorities

Furrion FGH12D2-BL 2 burner gas cooktop

Furrion designs for vehicle kitchens, and this stacked two-burner model is listed for specialty vehicle and food truck applications, the closest use case to a Sprinter galley on this list. A two-piece hinged glass cover folds over the burners, so the closed unit gives back a flat surface in a tight counter run.

The maker spec sheet gives a product size of 11 3/4 inches wide, 4 1/8 inches high and 22 3/4 inches deep, with a net weight of 15.4 lbs. The front burner is listed at 8,000 BTU and the rear burner at 6,500 BTU, burning propane. Electrical input is 12 volt DC, which matches a van house system directly, and ignition is automatic electric spark, lit from the vehicle battery side rather than a household circuit.

Details suit life on the move: the grate is die-cast, and the control knob carries an LED light that shows blue for decoration and turns red to indicate a burner is on with gas flowing, a clear signal in a small cabin. The maker lists compatibility as solo use or paired with a 13 inch range hood.

The depth is the catch: at 22 3/4 inches the unit runs front to back in a stacked layout, so it wants a counter with real depth even though the width is slim. The sheet does not print cutout dimensions, which must come from the maker install documents. Buy it for a deep, narrow counter and 12 volt ignition; skip it if the counter is shallow.

  • Pros: 12 volt DC ignition suits van electrics; hinged glass cover; vehicle applications listed by the maker
  • Cons: 22 3/4 inch depth; cutout size not in the spec sheet
  • Buy if: the galley counter is narrow but deep
  • Skip if: counter depth is limited

Dometic PI8022 two burner cooktop

Dometic supplies much of the vehicle kitchen market, and the PI8022 is its compact two-burner gas hob with a glass lid that doubles as workspace when closed. At a listed net weight of 3.58 kg it is by far the lightest unit in this guide, which matters in a conversion where payload is counted carefully.

The Dometic document lists output of 1.1 kilowatts for one burner and 1.8 kilowatts for the other, a combined heat output of 10.5 MJ per hour split as 4 MJ per hour from the small left burner and 6.5 MJ per hour from the large right burner. Overall size is printed as 480 mm wide, 80 mm high and 370 mm deep, a shallow footprint that leaves room in the cabinet below for storage or a small oven box.

Ignition is push-button piezo, so no electrical supply is needed at all, and the duo-coloured knobs give a clear read of each burner setting. Detachable trivets lift off for cleaning, and the stainless steel finish matches the sink and tapware used in many European-style van builds, the market this model line is documented for.

That market point is the limit: the specification document read for this guide is written for a non-US market, in metric figures, and US availability was not confirmed from the page opened, so a US builder should confirm supply and gas fittings with the maker before planning around it. Buy it for minimum weight and a shallow cabinet; skip it if US-market documentation is required.

  • Pros: lightest model listed at 3.58 kg; piezo ignition needs no power; shallow 370 mm depth
  • Cons: non-US market documentation; US supply not confirmed; modest output
  • Buy if: payload and cabinet depth are the tightest constraints
  • Skip if: the build needs US-market paperwork

Summit GC2BGL 2 burner gas-on-glass cooktop

The Summit GC2BGL is a household domino cooktop that earns its place here on size alone: at 12.25 inches wide it drops into the kind of narrow counter slot a van galley can offer, while bringing sealed burners and a ceramic glass surface that look and clean like a home kitchen unit.

The maker brochure lists dimensions of 12.25 inches wide, 20.38 inches deep and 2 inches high, a weight of 15.0 lbs and a cutout of 11 inches wide, 18.88 inches deep and 2.5 inches high. The two sealed burners are rated at 8,350 BTU and 3,400 BTU, under continuous cast iron grates on a black EuroKera ceramic glass surface, with dial controls and spark ignition on a 115 volt AC supply.

Two listings matter for a gas install in a small cabin. The maker states the thermocouple flame failure protection turns the gas off after 12 seconds if the flame is extinguished, and the unit is preset for natural gas but converts to LP with an included conversion kit, the configuration a propane van system needs. The brochure lists a 1 year parts and labor warranty.

As a household appliance it is documented for built-in kitchen installation, not for a vehicle, so mounting and gas work must be planned with the maker guidance and local rules rather than assumed. The small burner at 3,400 BTU is a true simmer burner. Buy it for a 12 inch slot and a glass top finish; skip it if vehicle documentation is required.

  • Pros: published cutout; LP conversion kit included; flame failure protection with a stated shutoff time
  • Cons: household documentation only; small burner is simmer strength
  • Buy if: a narrow glass-top domino fits the counter plan
  • Skip if: vehicle-specific documentation is a requirement

Buying guide

A van cooktop choice is really three decisions stacked together: which fuel the build carries, how much counter and cabinet the unit can take, and how the cooking load fits the systems already installed. The points below follow that order, using the figures the makers of the six models above actually publish.

Sizing cooktops for sprinter conversion counters

Start with the counter, not the catalog. Measure the run length, the depth from wall to edge and the cabinet depth below, then compare those numbers with the published overall size and cutout of each candidate, such as the Empava cutout of 19.5 by 13.5 inches or the Summit cutout of 11 by 18.88 inches.

Layout shape matters as much as raw size. Portrait and stacked models like the Kenyon and the Furrion put their length front to back, which suits a short run with a deep counter, while side-by-side domino models like the Summit and the Empava spread along the run. Sketch both orientations at full scale before committing.

Leave the maker clearances in the sketch as well. Suburban, for example, prints minimum distances to combustibles of 18 inches vertical, 8 inches at the back and 6.0 inches at each side for the SDN2U. A cooktop that fits the cutout but breaks the listed clearances does not fit the build.

Choosing between propane and induction in a van

Propane carries its energy in a tank and asks little of the electrical system: the Furrion lights from a 12 volt DC input, the Dometic piezo needs no power at all, and the Suburban lights by match. For conversions that cook daily off grid with a modest battery bank, gas keeps the cooking load off the batteries entirely.

Induction moves the load onto the electrical system, where it is large and easy to underestimate. The Empava needs a 120 volt, 20 amp supply for its shared 1800 watts, and the Kenyon lists boost figures up to 1500 watts even on its 120 volt models. Size the inverter, wiring and battery bank for those printed numbers.

Fuel choice also changes the rest of the build. Gas needs a tank, a regulator, listed clearances and ventilation planning, while induction needs magnetic cookware and removes the open flame. Neither is universally better; the right answer is the one the rest of the conversion already supports.

Reading burner output figures honestly

Makers publish output in different units, and the figures are not interchangeable at a glance. This guide alone contains BTU per hour for the US gas models, kilowatts and MJ per hour for the Dometic, and watts for the induction units, so compare within a fuel type first and treat cross-fuel comparisons as rough at best.

Look at the spread between burners, not just the biggest number. The Summit pairs an 8,350 BTU burner with a 3,400 BTU simmer burner, the Furrion pairs 8,000 with 6,500 BTU, and the Suburban runs two equal 6,500 BTU per hour burners. A wide spread suits varied cooking; equal burners suit two similar pots. On induction, check whether the headline wattage is shared, as the Empava shares its 1800 watts.

Boost figures need the same care. Kenyon lists boost as a temporary mode lasting up to 10 minutes: plan around the continuous figures and treat boost as a head start for bringing a pot to the boil.

Covers, lids and getting counter space back

In a van, the cooktop sits in the middle of the only work surface, so a cover is not a cosmetic extra. The Furrion folds a two-piece hinged glass cover over its burners, the Dometic glass lid doubles as workspace when closed, and Suburban offers flush mount glass covers for the SDN2U as accessories.

A cover also changes the daily routine: burners must be cold before the lid closes, and the closed surface is a prep area, not a storage shelf for heavy items. Check whether the cover is included or an accessory before comparing two models, because an accessory cover adds a second purchase to the build.

Where no cover exists, plan a separate board or fold-down surface in the galley design instead.

Installation points to confirm with the maker

Before ordering, confirm four things from the maker or the install documents: the exact cutout, the fuel connection and pressure, the electrical input, and the clearances. The models here show why: pressures are printed in inches W.C. for the Suburban, and the Summit ships preset for natural gas with an LP kit in the box.

Ask also what the maker says about the setting. Furrion lists specialty vehicle and food truck applications, Suburban documents vehicle counter tops, and Summit documents a household built-in. Finally, confirm ventilation for the galley as a whole: cooking in a small enclosed cabin adds moisture and combustion products to a tiny air volume with gas, and heat and steam with any fuel.

FAQ

Converters tend to ask the same handful of questions once the counter is measured and the fuel decision is close. The answers below stick to the figures and listings published for the six models in this guide, plus general planning points that apply to any small galley build.

How many burners do cooktops for sprinter conversion galleys need?

Two burners cover the large majority of van cooking: one pot or pan in active use and one holding, reheating or boiling alongside. Every model in this guide is a two-burner unit, in line with the counter space a Sprinter galley can give up, and a bridge zone, like the one Kenyon lists, stretches two burners under one long pan when needed.

Three-burner vehicle cooktops exist in the wider RV market, but they take a longer counter run and a bigger cutout, which usually takes the sink size or the only prep area.

Can an induction cooktop run from a van battery system?

It can, through an inverter, but the printed figures decide whether it should. The Empava lists a 120 volt, 20 amp requirement and 1800 watts shared across its burners, and the Kenyon lists boost up to 1500 watts on 120 volt models, so the inverter must be rated for those loads continuously, not just at a brief surge figure.

Run time is the second half of the question. High wattage draws drain a battery bank quickly, so all-electric cooking suits builds with large banks, strong charging or regular shore power.

Does a propane cooktop need an electrical connection in a van?

Some do and some do not, and the listings here show the full range. The Furrion uses a 12 volt DC input for its automatic spark ignition, the Summit uses a 115 volt AC supply for spark ignition, the Dometic piezo lights with a push button and no supply, and the Suburban is match lit.

That detail matters during the build because the ignition supply has to be wired or deliberately omitted before the counter goes in. Check the ignition line in the maker spec sheet for the exact model, since makers sell several ignition types side by side.

What size cutout should be planned before the counter is made?

Plan from the published cutout of the chosen model and nothing else. In this guide the Empava cutout is listed at 19.5 by 13.5 inches and the Summit cutout at 11 inches wide by 18.88 inches deep by 2.5 inches high, while the Suburban and Furrion sheets reference their install documents for the opening, which must be read before cutting.

Overall size and cutout size are different numbers on every model, and the gap between them is where the flange sits and the seal lands. Ordering the counter work from the overall dimensions alone is the most common way a conversion build ends up with a hole the cooktop falls through or will not enter.

Are these cooktops approved for use in a Sprinter?

No maker page read for this guide claims approval for a specific vehicle model, and this guide does not claim it either. What the pages do state is the intended setting: Furrion lists specialty vehicle and food truck applications, Suburban documents its drop-in for RV and camper counter tops, and Summit documents a household built-in installation.

Treat those listings as the starting point, then confirm the complete installation, including gas work, clearances and ventilation, with the maker and a qualified installer working to the rules where the van is registered and used.

Conclusion

For most Sprinter galleys the short list is honest: propane drop-ins from Suburban and Furrion fit the classic vehicle pattern, the Dometic wins on weight, the Summit brings a household glass finish, and the Kenyon and Empava serve all-electric builds with the inverter capacity to feed them. Match fuel first, cutout second.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.