Updated Nov 15, 2026· 15 min read

Key takeaways

  • Compare downdraft fans for cooktops by blower type, CFM, rise height and ducting: telescopic and cooktop-level models from six makers, with all listed specs.

An island or peninsula cooktop often has no wall for a hood and no appetite for a canopy over the room, which is the gap a downdraft fills: it hides in the counter and pulls steam and grease down at the cooking surface. This guide compares downdraft fans for cooktops on maker figures: blower type, airflow, rise height and ducting.

Quick verdict

Five of the six picks are telescopic units that rise behind the cooktop, and one works at cooktop level beside the burners. The real split is the blower: some models include an internal blower, others are sold without one and pair with internal, inline or remote blowers chosen for the duct run and the noise target.

Product Type Best for Key spec Main limit
Thermador UCVM30XS Telescopic downdraft, blower separate Flexible duct routing in a 30 inch install 15 inch rise, blower options from 600 to 1000 CFM Blower is a required separate purchase
Fisher & Paykel HD36 Telescopic downdraft, blower separate Wide 36 inch cooktops, slim profile Rises to 14 inches, depth only 2 1/8 inches Internal blower sold separately
Elica Rise ERS636S1 Telescopic downdraft, internal blower All-in-one 36 inch install 600 CFM internal blower included, rises 14 inches Ducted installation only
Faber Scirocco Plus SCIR3014SSNB-B Telescopic downdraft, blower separate Remote blower power up to 1200 CFM Three blower options, reversible motor box Sold with no blower fitted
Broan Eclipse 273003 Telescopic downdraft, internal blower Simple dial control and sliding blower position 600 CFM interior blower, discharge in 3 directions Ducted only, no recirculation option
Gaggenau VL 414 712 Cooktop-level downdraft, motorless Modular Vario cooktop layouts Sensor-controlled automatic mode, 10 watt load Needs a separate blower per unit

How we selected

Selection required a current maker document or a current sales listing for every model, with the blower arrangement stated in plain terms: included internal blower, or a named list of separate blowers with their CFM ratings. Models whose maker pages report them as discontinued were excluded, however good their old figures looked.

The set was also kept distinct from earlier ventilation roundups on this site on purpose. Every model here is different from the pop-up vents covered before, so a reader comparing across guides meets new options rather than the same six names reshuffled, and each entry below stands on its own opened page.

Within the set, variety was deliberate: widths of 30 and 36 inches, rise heights of 14 and 15 inches, one unit with a fully included blower package, and one cooktop-level design that does not rise at all. Downdraft buyers are really choosing a duct plan and a blower plan, so the entries focus on those two decisions.

Six downdraft fans for cooktops, compared

The entries below give the published airflow, rise and duct figures first, then the practical trade-offs. Where a blower is sold separately, that fact is stated in the entry rather than buried, because it changes both the parts list and the installed total for the project.

Thermador UCVM30XS 30 inch downdraft ventilation

The Thermador UCVM30XS is a 30 inch Masterpiece Series downdraft with the tallest rise in this guide: the maker lists a 15 inch telescopic rise, so the intake stands well above pot rims on a standard cooktop. It is the pick where duct routing is awkward and blower choice needs to stay open.

The unit is sold without a blower, and the maker lists the options plainly: remote blowers at 600 CFM and 1000 CFM, inline blowers at 600 CFM and 1000 CFM, and a flexible blower at 600 CFM that mounts with the unit. Speed settings are 3-stage, the grease filter is a washable synthetic multilayer cassette, and the electrical listing is 120 volts at 10 amps with a 30 inch power cord.

Features listed by the maker include an automatic mode, a delay shut-off and a check filter light. The operating mode is convertible between ducted and recirculating, with the recirculation kit listed for induction and electric cooktops only. Net weight is listed at 37 lbs, and the maker lists a limited warranty of 2 years for parts and labor.

The trade-off for the flexibility is planning: a blower, and for some layouts a transition, must be specified and bought separately, and a gas cooktop install needs the maker seal trim kit. Buy it for routing freedom and the tall rise; skip it if a single-box purchase with the blower inside is the goal.

  • Pros: 15 inch rise; five listed blower options; ducted or recirculating
  • Cons: blower sold separately; gas installs need an extra trim kit
  • Buy if: the duct run is long or turns through tight cabinet space
  • Skip if: you want the blower included in the box

Fisher & Paykel HD36 downdraft range hood

The Fisher & Paykel HD36 is a 36 inch Series 7 telescopic downdraft with an unusually slim profile: the maker lists the depth at just 2 1/8 inches, so the unit takes very little of the cabinet behind the cooktop. It rises to 14 inches while cooking and slides away into the countertop when the meal is done.

The maker pairs it with an internal blower rated at 600 CFM, listed as an accessory sold separately under the model HBD600I. Overall height is given as a range, 28 1/4 to 42 1/4 inches, covering the lowered and raised positions, and extraction is ducted at the front or the side. Power requirements are printed as 120 volts, 60 Hz and a rated current of 15 amps.

Controls are kept simple: a single on and off button plus a slider that adjusts fan speed up or down. The stainless steel mesh filters trap grease during extraction, and the maker says they are easy to remove and lists dishwasher cleaning or a hand wash in hot soapy water.

The limits follow the design: one blower pairing is documented on the product page, so there is less room to scale airflow than with multi-blower systems, and the blower is a separate line item. Buy it for a wide cooktop and a thin cabinet footprint; skip it if a remote blower plan is already drawn.

  • Pros: very slim 2 1/8 inch depth; 14 inch rise; simple slider control
  • Cons: blower sold separately; one documented blower pairing
  • Buy if: cabinet depth behind the cooktop is tight
  • Skip if: the design calls for a remote blower

Elica Rise ERS636S1 downdraft hood

The Elica Rise in the 36 inch ERS636S1 version is the all-in-one entry in this guide: the 600 CFM blower is internal and included, so the parts list stays short. The maker lists dimensions of 36 inches wide, 12 1/2 inches deep and 14 inches high, and the unit rises a full 14 inches above the countertop.

Blower speeds are 3 plus a boost setting, with noise listed at 6.8 sones. Control is by an external electronic rotating disk with an LCD, mounted into the countertop or the cabinet face rather than on the unit itself, which keeps the counter line clean. The grease filter is an anodized aluminum mesh filter behind the perimeter aspiration panel, and the maker lists it for dishwasher cleaning.

Installation is ducted only, through a round 6 inch discharge that can point in more than one direction, and the maker notes the blower can be rotated to the opposite side to make room in the cabinet. Electrical figures are 120 volts, 60 Hz and 550 watts. The warranty is listed as 2 years parts and in-home labor, with an added year of both when the product is registered with the maker within 3 months.

The trade-off is the mirror of the Thermador: nothing to scale. The internal blower is the blower, so a long or difficult duct run has no remote option to fall back on. Buy it for a straightforward ducted install; skip it if the duct path is long.

  • Pros: blower included; perimeter aspiration; control sits in the counter or cabinet face
  • Cons: ducted only; no remote blower option
  • Buy if: the duct run is short and direct
  • Skip if: the blower needs to live outside the cabinet

Faber Scirocco Plus SCIR3014SSNB-B downdraft hood

The Faber Scirocco Plus in 30 inch stainless form is sold with no blower fitted, and the maker offers three: an internal blower at 600 CFM, and remote blowers at 900 CFM and 1200 CFM. That top figure is the highest blower rating in this guide, aimed at high-output cooktops in island installs.

Ducting is flexible on paper: ducted or ductless with the maker conversion kit, a 6 inch round duct for the internal blower or a 10 inch round duct for a remote blower, and a reversible motor box that lets the hood sit behind a rangetop, a cooktop or a cooktop and oven combination. The maker positions the model for islands where an overhead canopy would block the room.

Controls are a variable speed slider with an on and off button, and the maker lists an auto-off function. Grease filters are stainless mesh and are listed for dishwasher cleaning. There is no lighting on the unit, which keeps the raised panel plain.

As with the Thermador, the separate blower is both the strength and the homework: the blower choice sets the airflow, the duct size and part of the install labor. Buy it for high-output cooking and blower choice; skip it if the project needs a fixed, simple specification.

  • Pros: remote blower options to 1200 CFM; reversible motor box; ducted or ductless
  • Cons: no blower included; no lighting
  • Buy if: the cooktop output is high and the island is the room centerpiece
  • Skip if: a mid-power, single-box unit fits the cooking style

Broan Eclipse 273003 downdraft system

The Broan 273003, from the Eclipse series, is the traditional entry: a 30 inch telescopic downdraft with its interior blower included, rated up to 600 CFM in the listing. An exterior blower version at 900 CFM is also listed for installs that want the motor outside the house envelope.

Control is an infinitely adjustable rotary dial recessed into the side of the unit, so speed is a twist rather than a set of steps. The listing gives dimensions of 30 inches wide, 29.5 inches high and 7 inches deep, electrical figures of 120 volts, 4 amps and a 480 watt motor, and a typical sound level of 3 sones at normal working speed. The listing also states HVI certified performance.

Duct planning is the strong point: the blower can discharge to the right, to the left or straight down, and it slides side to side under the counter to work around joists and cabinet frames. Duct sizes are listed as 6 inch round or 3 1/4 by 10 inch depending on configuration. The aluminum filter is reached from the front for cleaning.

Ventilation is ducted only, with no recirculation route, and the maker listing is clear that the space behind and below the cooktop belongs to the blower housing, so it cannot share that space with an oven. The listed warranty is 1 year. Buy it for duct routing freedom with the blower in the box; skip it if ductless operation is required.

  • Pros: blower included; discharge in three directions; blower slides side to side
  • Cons: ducted only; cannot install with an oven below the cooktop
  • Buy if: joists or framing dictate where the duct can go
  • Skip if: the kitchen cannot be ducted outside

Gaggenau VL 414 712 Vario downdraft ventilation

The Gaggenau VL 414 712 is the different idea in this guide: a cooktop-level downdraft that does not rise at all. It sits in the counter beside the cooktop as part of the Vario 400 series, built from 3 mm stainless steel, and pulls vapors sideways at surface level into a metal grease filter.

The unit is motorless. The maker lists air extraction with three separate blower models and a dedicated recirculation blower, and recommends one blower for each VL unit. Airflow therefore depends on the blower chosen, and the maker document read for this guide prints no single CFM figure for the unit itself, so none is claimed here.

What is printed: 3 electronically controlled power levels plus an intensive mode, automatic sensor-controlled adjustment as cooking vapors build up, a run-on function, and interval ventilation of 6 minutes. The control knob has an illuminated ring. Total connected load is just 10 watts, on a 68 inch connecting cable with a standard three-prong plug, and the unit supports the maker home network integration.

Planning rules are specific: the maker sets the maximum cooktop width between two VL units at 24 inches, and recommends an air deflector when a unit sits next to a gas appliance. The overflow capacity is listed at 8.5 oz. Buy it for a modular Vario layout planned as one system; skip it for a standard cooktop that needs a self-contained vent behind it.

  • Pros: no moving chimney; sensor-controlled automatic mode; tiny 10 watt connected load
  • Cons: blower is a separate system decision; built around the Vario series
  • Buy if: the kitchen is already planned around modular Vario cooktops
  • Skip if: a conventional cooktop needs a standalone downdraft

Buying guide

Choosing between these six is mostly a matter of matching the blower plan to the duct run and the cooktop output, then checking the cabinet can give up the space the unit and its blower need. The points below follow the order an installer will ask about them.

Matching downdraft fans for cooktops to the duct run

Start under the counter, not at the cooktop. A downdraft needs a path from the cabinet to the outside wall or roof, and that path decides the blower style: internal blowers suit short runs like the Elica at 600 CFM, while remote and inline blowers, offered up to 1000 CFM by Thermador and 1200 CFM by Faber, suit longer paths.

Discharge direction is the second half of the same question. The Broan blower discharges right, left or down and slides side to side; the Thermador lists 6 discharge configurations; the Fisher & Paykel extracts at the front or the side. Sketch the joists and cabinet frames first, then pick the unit whose listed discharge options fit the sketch.

Duct size follows the blower. Figures in this guide run from the Elica round 6 inch discharge to the Faber 10 inch round duct for remote blowers, with the Broan also listing a 3 1/4 by 10 inch rectangular option. A duct smaller than the maker lists will not deliver the rated airflow, whatever the blower is called.

Included blower or separate blower

An included internal blower, as on the Elica Rise and the Broan Eclipse, makes the purchase and the specification simple: one product, one airflow figure, one install. It is the right default for a standard 30 or 36 inch cooktop with a short duct run to an outside wall.

A separate blower, as on the Thermador, Faber and Fisher & Paykel, adds a decision and a second product to the order, but it buys two things: airflow that can be sized up for a high-output cooktop, and a motor that can sit inline in the duct or outside the room, away from the cooking conversation.

The Gaggenau sits further along the same line: the ventilation unit and its blower are planned as parts of a modular cooktop system. That approach rewards a full kitchen plan drawn at once and punishes a one-piece replacement purchase.

Rise height and capture at the pan

A downdraft fights the natural rise of steam, so the height of the intake matters. The telescopic models here rise to 14 inches for the Fisher & Paykel and the Elica, and to 15 inches for the Thermador, which puts the intake closer to the top of a tall stockpot than a low vent slot can reach.

Back burners are the weak point of every downdraft, because the intake sits behind the cooktop and front burner steam has further to travel. Makers answer this differently: Elica lists perimeter aspiration around the panel, and Gaggenau removes the travel entirely by placing the intake at cooktop level beside the burners.

Match the width as well. Every telescopic model here is built to sit behind a cooktop of its own width class, 30 inches against 30 and 36 against 36, and a vent narrower than the cooktop leaves the outer burners at the edge of the capture zone.

Controls, filters and daily upkeep

Control styles in this set range from the Broan rotary dial and the Fisher & Paykel slider to the Elica rotating disk set into the countertop and the Thermador automatic mode with a check filter light. In a working kitchen the best control is the one that can be found and set with wet hands without looking down for long.

Filters decide the weekly routine. The makers here list mesh or cassette grease filters that can be removed for cleaning, several of them listed for dishwasher cleaning, and the Gaggenau adds a saturation indicator for its grease and charcoal filters. A filter that is easy to reach, like the Broan front access design, gets cleaned more often in real life.

Recirculation deserves a last check. Only some models offer it: the Thermador with a kit listed for induction and electric cooktops only, and the Faber with a ductless conversion kit. The Elica and the Broan are ducted only, so a kitchen with no outside path rules them out at the first sketch.

FAQ

Most downdraft questions come down to whether the format can handle a given cooktop and a given house. The answers below use the figures published for the six models above, plus general planning points that apply to any downdraft install in any kitchen layout.

Are downdraft fans for cooktops strong enough for a gas cooktop?

They can be, when the blower is sized to the cooktop. The separate-blower models here scale highest: Faber lists remote blowers at 900 and 1200 CFM and Thermador lists remote and inline options at 1000 CFM, while the included-blower Elica and Broan units are rated at 600 CFM for standard cooktop loads.

Two maker notes apply to gas installs in this set: Thermador requires a seal trim kit when its downdraft is installed with a gas cooktop, and Gaggenau recommends an air deflector when a VL unit sits next to a gas appliance. Treat those accessories as part of the specification, not as optional extras.

Can a downdraft work without ducting to the outside?

Sometimes, yes. The Thermador converts to recirculating with a kit the maker lists for induction and electric cooktops only, the Faber offers a ductless conversion kit, and the Gaggenau has a dedicated recirculation blower among its listed options for exactly this case.

The Elica Rise and the Broan Eclipse are ducted only, so they need a real path outside. Recirculating setups filter grease and odors but return heat and moisture to the room, which is why several makers restrict their kits by cooktop type.

How much cabinet space does a downdraft take?

More than the slim counter slot suggests. The Fisher & Paykel lists a depth of only 2 1/8 inches for the unit itself, but every model also needs room below for its housing and blower: the Thermador lists overall dimensions of 44 3/8 inches high, 31 inches wide and 2 3/4 inches deep, and the Broan listing gives 29.5 inches of height.

The practical consequence shows up in the Broan listing note: the blower housing and ducting occupy the space behind and below the cooktop, so that space cannot be shared with an oven. Plan the cabinet as ventilation space first and storage second.

Why do some downdrafts need a second purchase for the blower?

Because the blower is treated as a system part rather than a fixed component. Thermador lists five blower options for the UCVM30XS across remote, inline and flexible types, and Faber lists three for the Scirocco Plus, so one vent body can serve a short duct run or a long one without being redesigned.

The separate blower also moves the noise source. An inline or remote blower puts the motor in the duct run or outside the room, which is the main reason open-plan kitchens choose this format. The trade is a longer parts list and more install planning.

Conclusion

For a simple install, the Elica Rise and the Broan Eclipse bring their blowers with them; for power and quiet, the Thermador and the Faber pair their vents with separate blowers up to 1000 and 1200 CFM; the Fisher & Paykel wins on slim depth, and the Gaggenau suits a modular plan. Decide the duct path first, and the model follows.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.