Key takeaways
- Only three 30 inch gas cooktops with downdraft are made, by KitchenAid, JennAir and GE Profile. Compare burners, JX3 and downdraft vents, cutouts and finishes.
Three models are the entire market for 30 inch gas cooktops with downdraft: the KitchenAid KCGD500GSS, the JennAir JGD3430GS and the GE Profile PGP9830SRSS in stainless. This guide compares the three on the figures their pages publish, from burner output and vent systems to cutout sizes and finishes.
Quick verdict
KitchenAid brings the strongest named burners to the size, a 17K BTU and a 15K BTU Professional Burner on one 30 inch surface. JennAir publishes the deepest spec sheet, with every burner mapped and cutout figures printed. GE Profile builds its entry on a gas-on-glass surface in stainless, with an 11,500 BTU all-purpose burner stated.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS | 30 inch gas downdraft | High-heat cooking at 30 inches | 17K BTU Professional Burner, 300 CFM exhaust rating | Cutout figures not published on the maker page |
| JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS | 30 inch gas downdraft | Planning a replacement from printed figures | Full burner map, cutout 28-5/8 by 19-15/16 inches | Listing gives two different blower figures |
| GE Profile 30 inch Built-In Gas Downdraft Cooktop PGP9830SRSS | 30 inch gas downdraft, stainless | A stainless glass surface at this size | 11,500 BTU all-purpose burner, gas on glass | Full burner map not stated on the listing |
The shared ground is exact: 30 inch class, four burners, gas fuel, a vent built into the cooktop and no hood above the surface. The differences are in how much heat the top burner makes, how much of the spec sheet each maker prints, and whether the surface under the grates is steel or glass.
How we selected
This keyword’s field was built from maker and listing pages only, one model at a time. A model had to be a built-in 30 inch gas cooktop with the downdraft vent inside the unit. Ranges with downdraft styling, electric downdraft cooktops and induction models with a vent pairing were all excluded by that rule.
Three platforms qualify. Everything else that search results attach to this keyword is a finish of one of those three, an older discontinued line, or a different fuel wearing the wrong label. The black finish of the GE platform and the black finish of the JennAir are the clearest examples of the first kind.
Specs below are quoted from the page opened for each model, in that page’s own terms. KitchenAid names burners in K BTU and states an exhaust rating. JennAir’s listing prints a per-burner map in full BTU and a Motor Class blower figure. The GE listing states one headline burner and the product dimensions, and leaves the rest of the map unstated.
Sale status is deliberately not argued in this guide. Listings change, and one platform in this group carries conflicting signals between its own pages, so availability is a question for the listing page on the day of purchase. What the guide does settle is the hardware: burners, vents, dimensions and finishes, as published.
30 inch gas cooktops with downdraft, one model at a time
The three sections below take the models in order of published burner strength. Each one sets out who the cooktop suits, the figures on its page, the conversion story for propane, and the point where the page stops publishing and a buyer has to ask for more.
KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS
The maker page presents a 30 inch, four-burner cooktop in stainless steel with downdraft ventilation built in. It is the compact half of KitchenAid’s gas downdraft pair, and its page leads with the same burner names and the same vent rating as the maker’s wider 36 inch model.
Three burners are named with figures: a 17K BTU Professional Burner, a 15K BTU Professional Burner and a 5K BTU Even-Heat Simmer Burner. On a 30 inch surface, two burners of that strength is the headline fact of this whole group; most cooking that needs real heat, a pasta pot at a rolling boil or a skillet at a hard sear, has a home here.
The vent is stated as a 300 CFM Exhaust Rating with a 3-Speed Fan Control. The maker lists the cooktop as convertible to duct-free ventilation, lists an LP Conversion Kit for propane households, and describes the downdraft as removing the need for a separate hood over the surface.
The page’s limits are about paper, not hardware. The fourth burner’s output is not stated in the wording the maker publishes, and the opened page carries no dimension table, so cutout width and depth have to come from the install guide for the model before a counter is cut around it.
- Pros: strongest named burner pair at this size; 300 CFM exhaust rating; duct-free conversion listed; LP kit listed
- Cons: fourth burner output not stated; no dimension table on the maker page
Buy if heat is the reason you are shopping and your cutout is already known to fit the KitchenAid install figures. Skip if you want to plan the whole replacement from one listing page, because the JennAir below prints the figures this page leaves out.
JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS
The listing for this JennAir model is the most paper-rich page in the group. It names the cooktop as a 30 inch JX3 gas downdraft unit, prints a width of 30 inches and a depth of 21-1/2 inches, and then does what the other pages do not: it maps every burner on the surface.
The map reads left front 17,000 BTU, right rear 15,000 BTU, right front 10,000 BTU and left rear 5,000 BTU. That spread matches the KitchenAid at the top and adds a stated mid-range, so a cook can assign the stockpot, the skillet and the saucepan their positions before the unit is out of its box.
Ventilation is the JX3 Downdraft Ventilation System with 3 Speeds. The page states the blower two ways: the feature text says 297 CFM Motor Class, and the spec table lists CFM Motor Class as 310. Both figures are reported here, with the spec table treated as the formal entry and the gap flagged rather than hidden.
Planning figures continue with a cutout width of 28-5/8 inches, a cutout depth of 19-15/16 inches and a net weight of 46 lb. The listing marks the cooktop LP Convertible with the kit included, which settles the propane question in print for this model in a way the other two pages do not quite match.
- Pros: every burner output published; cutout and weight figures published; LP kit listed as included
- Cons: blower figure stated two ways on one page; duct-free conversion details thinner than the burner data
Buy if printed figures drive your decision, especially for a replacement where the old cutout is fixed. Skip if the two blower numbers on one page bother you more than the fuller data pleases you; the KitchenAid page is cleaner, if thinner.
GE Profile 30 inch Built-In Gas Downdraft Cooktop PGP9830SRSS
The listing for this GE Profile model, in its stainless finish, describes a 30 inch built-in gas cooktop with four burners and downdraft exhaust. Its surface is gas on glass: burners mounted over a glass ceramic panel, a construction the other two models in this group do not use.
The burner figure the listing states is an 11,500 BTU all-purpose burner. A full per-burner map is not stated on the opened listing, so the honest summary is that this model’s published top figure sits below the 17,000 BTU class burners of its rivals, and the rest of its map is a question for the maker’s full spec sheet.
Dimensions are stated in full: product width 29 3/4 inches, depth 21 7/8 inches and height 23 7/8 inches. That height figure is the one to study, because it includes the downdraft housing below the surface, the part of the unit that shares space with the cabinet and drawer run underneath.
The stainless finish is this entry’s reason to exist beside its black sibling. The platform is the same, the downdraft exhaust is the same idea, and the choice between the two finishes is a kitchen-design decision. What this listing adds is a glass surface that wipes down in one pass once it has cooled.
- Pros: stainless finish on a glass surface; full product dimensions stated; downdraft exhaust built in
- Cons: only one burner figure stated on the listing; top output below both rivals
Buy if the stainless glass look is the one your kitchen needs and your cooking sits in the everyday range. Skip if you sear hard and often, or if you want the complete burner map in print before money moves; both rivals publish more heat on paper.
Buying guide
Three models make for a short shortlist and a long checklist. The guide below covers the cutout and cabinet questions first, then the burner and vent figures, then the fuel conversion and finish decisions, in the order a real purchase tends to raise them.
Cutout, depth and the cabinet below
Start under the counter, not on top of it. A downdraft cooktop is a cooktop plus a vent housing, and the housing hangs where a drawer stack usually lives. The GE listing’s height of 23 7/8 inches shows the scale of that claim; the JennAir prints a cutout of 28-5/8 by 19-15/16 inches for the hole in the counter itself.
For a replacement, measure the hole you have. Cooktops in the same nominal class do not share one cutout, and the difference between a drop-in fit and a counter modification is a fraction of an inch in the wrong place. The KitchenAid install guide has to supply its figures, since the maker page read here prints no dimension table.
Weight plays into the install as well. The JennAir listing states a net weight of 46 lb, light enough for a two-person lift without drama. The point is not the number itself but the planning: a built-in unit is carried, leveled and connected in a tight cabinet opening, and the printed figures are what the installer works from.
Heat at the top, control at the bottom
The top of the range separates these models cleanly. KitchenAid and JennAir both publish a 17,000 BTU class burner, KitchenAid adding a named 15K BTU second burner and JennAir a mapped 15,000 BTU right rear. GE’s stated figure is 11,500 BTU for its all-purpose burner, a clear step down in published heat.
The bottom of the range is closer. KitchenAid names a 5K BTU Even-Heat Simmer Burner, JennAir maps its left rear at 5,000 BTU, and low figures like those are the ones that hold a sauce or melt butter without constant stirring. A buyer choosing on heat should weight the top of the range, because the bottom is well covered by all three.
Maps beat headlines when both exist. JennAir’s full map lets you see the whole surface at once, including the 10,000 BTU right front that does most weeknight work. KitchenAid’s named burners cover three of four positions. GE’s single stated figure leaves the most to the full spec sheet, and that difference in published detail is itself a buying fact.
Vent systems and the figures behind them
Each model vents through its own surface, and each maker describes that vent differently. KitchenAid states a 300 CFM Exhaust Rating with a 3-Speed Fan Control. JennAir names its system JX3, gives it three speeds, and states a Motor Class blower figure that its own listing prints as both 297 and 310.
GE’s listing simply states downdraft exhaust without a CFM figure on the page opened here. That absence matters for comparison method: a model with no published vent number cannot be ranked on vent strength from its listing, and this guide does not borrow a figure from the platform’s other finish or from roundups to fill the space.
In installed life, all three vents live or die by the duct run beneath them. A short, straight duct to an outside wall serves any of these systems better than a long run full of turns serves a nominally stronger one, so the vent path in your floor or cabinet run deserves as much attention as the figure on the page.
Propane, ignition and daily controls
Propane households are covered by all three platforms, at three levels of clarity. JennAir’s listing says LP Convertible with the kit included. KitchenAid lists an LP Conversion Kit on its maker page. GE’s conversion story sits in the platform documentation rather than this listing, so confirm it on the maker’s page for the exact finish.
Conversion is a fitting job, not a setting: burner orifices and adjustments change for propane, and an installer does the work as part of putting the unit in. The buying task is simpler, which is to have the kit question answered and priced before the cooktop is ordered, in writing, for the exact model suffix.
Daily controls are knobs on all three, placed by each maker’s habit. The choice that will register every day is not knob style but burner layout: which corner holds the strong burner, and whether the low burner sits where your sauce hand expects it. The published maps in the product sections are the tool for that decision.
Steel or glass: the surface decision
Two of these cooktops present a metal surface around their burners, and the GE presents glass. A gas-on-glass surface wipes down in a single pass and shows spills plainly, which some cooks read as easy care and others as a surface that asks to be wiped after every pan.
Metal surfaces hide the ordinary marks of cooking better and match the stainless fronts most kitchens already have. The JennAir in this group is stainless, the KitchenAid is stainless, and the GE offers the choice in reverse: its platform comes in black and in the stainless finish covered here, over the same glass construction.
Neither surface changes the cooking. Burners, grates and vent do that. The surface decision is about cleaning habits and the look of the run of cabinets the cooktop sits in, and it is the one decision in this guide that can be made on sight alone.
FAQ
The questions below collect what shoppers most often ask once the shortlist is down to three: how many models truly exist, which figures are missing from which page, how the finishes relate, and what has to be settled before any of the three is ordered for a kitchen.
How many 30 inch gas cooktops with downdraft are sold?
Three platforms: one each from KitchenAid, JennAir and GE Profile. Each also appears in a second finish, which makes shop shelves look fuller than the category is. Counted by platform rather than by finish, the field is the three models in this guide, and no fourth maker sells into it on current pages.
That is a change from older years, when more downdraft lines were current. Discontinued models still circulate in used listings and old roundups, and they inflate the apparent field. A model counts for a buyer only when a current page stands behind it, which is the standard applied throughout this guide.
Which model publishes the most complete figures?
The JennAir JGD3430GS, on its listing: a figure for every burner, a cutout width and depth, a product width and depth, and a net weight. Its one blemish is the blower figure printed two ways, 297 in the feature text and 310 in the spec table, and even that is visible rather than hidden.
KitchenAid publishes the strongest burner names but no dimensions on its maker page, and the GE listing publishes full dimensions but only one burner figure. Completeness depends on which figures you need: heat shoppers are best served by KitchenAid and JennAir, cabinet planners by JennAir and GE.
Is the stainless GE the same cooktop as the black one?
Same platform, different finish and model suffix. The PGP9830SRSS covered here is the stainless form of the GE Profile 30 inch gas downdraft platform; the black form carries the DRBB suffix. Burner layout and the downdraft exhaust belong to the platform, so the comparison in this guide is about the platform, with the finish as its visible variable.
One caution applies to finishes generally: confirm the exact suffix on the order. A cooktop ordered by platform name alone can arrive in the other finish, and the time to catch that is on the listing page before payment, not at the door with the installer booked.
Do any of these cooktops need a separate hood?
No. The downdraft vent is built into each unit, and KitchenAid states the point directly: its downdraft ventilation removes the need for a separate hood. The JennAir JX3 system and the GE downdraft exhaust are likewise complete vent plans inside the cooktop, which is the reason this category exists at 30 inches.
The vent still has to move air somewhere, through ductwork to the outside or through a duct-free conversion where a model lists one. KitchenAid lists its cooktop as convertible to duct-free ventilation. Your installer confirms which route your home takes and whether local rules have anything to add.
What should be settled before ordering one of the three?
Four things: the cutout your counter actually has, the cabinet space below it for the vent housing, the duct route or duct-free plan, and the fuel, natural gas or propane with its conversion kit. Every one of those is cheaper to settle on paper than after a built-in unit has been delivered.
Then confirm the finish suffix and read the current listing for the exact model on the day you buy. Pages change, kits move in and out of boxes, and the figure that matters is the one standing behind the model number at the moment of the order, not the one in any guide, this one included.
Conclusion
The field is three models deep and honestly counted: KitchenAid KCGD500GSS for named burner strength, JennAir JGD3430GS for the fullest printed figures, and GE Profile PGP9830SRSS for a stainless glass surface. Measure the cutout, plan the vent path, and let your cooking weight the burner maps in the end.