Updated Nov 17, 2026· 13 min read

Key takeaways

  • Three 30 inch gas cooktops with downdraft venting are sold, from KitchenAid, JennAir and GE. Compare burner maps, vent ratings, cutouts and conversion kits.

A 30 inch cutout rules out most downdraft cooktops before the shopping starts, which is why 30 gas cooktops with downdraft venting form such a short list: three models, from KitchenAid, JennAir and GE Profile. This guide compares their burner maps, vent ratings and cutout figures on published specs.

Quick verdict

Three makers split the category by personality. The KitchenAid KCGD500GSS leads on named burner strength, with 17K and 15K BTU burners published. The JennAir JGD3430GS publishes the fullest burner map and cutout figures. The GE Profile PGP9830DRBB states the strongest vent figure, a 400 CFM rating at high speed.

Product Type Best for Key spec Main limit
KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS 30 inch gas downdraft Named high-output burners 17K BTU and 15K BTU Professional Burners Fourth burner output and dimensions not stated on the maker page
JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS 30 inch gas downdraft Published cutout figures and burner map Cutout 28.625 by 19.938 inches, four burners mapped Listing pages disagree on the blower figure
GE Profile 30 inch Built-In Gas Downdraft Cooktop PGP9830DRBB 30 inch gas downdraft, gas on glass Strongest published vent rating 400 CFM at high speed, variable speed fan Lower burner outputs than the other two

All three are 30 inch, four-burner, gas units with the vent built into the surface and three fan speeds. The real spread sits in how much each maker publishes: full burner maps here, headline burners there, and vent figures stated in three different dialects that the buying guide untangles below.

How we selected

The filter for this keyword had four parts: 30 inch class, gas fuel, four burners in a built-in cooktop, and a downdraft vent built into the unit rather than a separate pop-up accessory. Electric 30 inch downdraft models from the same makers were set aside, because the keyword asks for gas.

Three distinct models pass that filter. The rest of the apparent field dissolves on inspection: the JennAir also appears in a black finish and the GE in a stainless finish, and those are finish variants of the same platforms, not extra models. Older GE downdraft lines surface in used listings, but no current sale page supports them as models you can order new.

Each model below is written from an opened maker or listing page, with the figures that page actually publishes: burner output by position where stated, the vent rating in the maker’s own terms, fan speeds, cutout dimensions where given, and the conversion notes for propane and duct-free venting.

Where pages disagree, the disagreement is printed rather than smoothed over. One listing in this guide carries two different blower figures for the same JennAir model on the same page, and the product section says which figure comes from the spec table and which from the feature text.

The three 30 gas cooktops with downdraft venting in detail

Three product sections follow, one per model. Each covers the burner set as published, the vent system and its rating, the grate and control layout, the conversion path for liquid propane, and the published cutout figures a replacement buyer needs before ordering anything.

KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS

The maker lists this 30 inch cooktop with four burners and downdraft ventilation integrated into the unit, with no separate hood needed. It is the smaller sibling of the 36 inch KitchenAid downdraft model, and it keeps the same published vent strength in the smaller cutout, which is its main claim on a buyer.

The burner names carry the story: a 17K BTU Professional Burner, a 15K BTU Professional Burner and a 5K BTU Even-Heat Simmer Burner are all stated on the maker page. Two burners at the top of the output range give this 30 inch surface more high-heat room than its size suggests, and the simmer burner carries a melt cap for low, gentle heat.

The vent is published as a 300 CFM exhaust rating with a 3-speed fan control, matching the figure on the maker’s 36 inch model. Full-width cast-iron grates cover the surface, stainless steel knobs run the burners, and the maker lists electronic ignition with automatic re-ignition across the cooktop.

For fuel and venting conversions, the maker lists an LP conversion kit, and lists the cooktop as convertible to duct-free ventilation with a kit sold separately. The gaps on this page are the fourth burner’s output, which is not stated, and a full dimension table, which the opened maker page does not publish.

  • Pros: two named high-output burners; full 300 CFM exhaust rating at 30 inches; full-width cast-iron grates; melt cap
  • Cons: fourth burner output not stated; dimensions not published on the maker page; duct-free kit sold separately

Buy if burner strength leads your list and your vent plan is ducted. Skip if you need every figure, cutout included, published before you order, since the JennAir below prints more of its numbers on the listing page.

JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS

The listing for this 30 inch model publishes the most complete paper trail in the group: four sealed burners with a figure for each position. Left front is 17,000 BTU, right rear 15,000 BTU, right front 10,000 BTU and left rear 5,000 BTU, so the whole surface can be planned before the unit arrives.

The 5,000 BTU position is an ultra-low output burner with a melt cap, and the burners are brass with a removable base. Continuous cast iron grates, three of them, run across the surface, the controls sit on the right side with metal knobs, and the maker lists DuraFinish Protection on the surface.

Ventilation is the JX3 downdraft system with three speeds. Here the page argues with itself: the feature text describes a vertically mounted 297 CFM Motor Class blower, while the spec table on the same page reads 310 for CFM Motor Class. This guide reports both figures and counts the spec table as the formal record.

The listing also publishes the planning figures the KitchenAid page leaves out: a cutout width of 28.625 inches, a cutout depth of 19.938 inches and a net weight of 46 pounds. The cooktop is listed as LP convertible with the kit included, with Flame-Sensing re-ignition, and as convertible to duct-free ventilation with an optional kit.

  • Pros: full per-burner map published; cutout dimensions and weight published; LP kit listed as included; brass burners
  • Cons: two different blower figures on the same listing page; duct-free kit optional

Buy if you are replacing an older 30 inch unit and want the cutout and burner figures in writing first. Skip if a single undisputed vent figure matters more to you than the fuller spec sheet, because this listing carries both numbers at once.

GE Profile 30 inch Built-In Gas Downdraft Cooktop PGP9830DRBB

The listing for this GE Profile model describes a 30 inch class cooktop, 29.75 inches wide overall, with four sealed burners on a gas-on-glass ceramic surface. Front center knob controls and electronic ignition run the unit, and the burners are factory set for natural gas.

The burner map is published in full and runs lower than the other two models: left front 9,100 BTU, left rear 9,100 BTU, right front 11,500 BTU and right rear 5,500 BTU. No position here reaches the 15,000 to 17,000 BTU band the KitchenAid and JennAir headline, which shapes this model toward ordinary weeknight cooking rather than hard searing.

The vent is where this model answers back. The listing states a downdraft exhaust rated at 400 CFM and 7.0 sones at high speed, with a variable speed fan at three speeds. That 400 CFM figure is the highest vent number published in this group, stated plainly as an exhaust rating at the top fan setting.

Planning figures are published too: overall dimensions of 29.75 inches wide by 21.875 inches deep by 23.875 inches high, and a net weight of 60 lb. The grates are medium cast, the maker lists them for dishwasher cleaning, and an LP conversion kit is included, listed under part number WB28X45706.

  • Pros: strongest published vent rating at 400 CFM; full dimensions published; LP conversion kit included; glass surface wipes down easily
  • Cons: burner outputs top out at 11,500 BTU; heaviest unit in the group at 60 lb

Buy if vent strength is your first concern and your cooking rarely asks for a very hot burner. Skip if high-heat searing is a weekly habit, since both other models publish burners half again as strong at the top of the range.

Buying guide

The buying guide works through the decisions a 30 inch downdraft buyer actually faces: reading three makers’ vent figures in three dialects, matching a burner map to real cooking, fitting the unit to an existing cutout, and settling the ducting and fuel questions before the order is placed.

Sizing 30 gas cooktops with downdraft venting to a real cutout

Nominal width is the start, not the answer. A 30 inch class cooktop can measure 29.75 inches across, as the GE does, and the hole it drops into is smaller than either figure. The JennAir listing publishes a cutout of 28.625 by 19.938 inches; the GE’s overall depth of 21.875 inches includes the vent housing below the surface.

Replacement buyers should measure the existing cutout in the counter, not the old cooktop’s top. Two of the three listings here publish enough figures to plan from; the KitchenAid maker page does not publish a dimension table, so its install guide has to be pulled before a counter is cut or a cabinet order is placed around it.

Depth below the counter matters as much as the hole in it. The downdraft housing hangs under the surface where drawers and cabinet boxes usually live, and the GE’s published height of 23.875 inches shows how much vertical room the vent hardware can claim. Check the cabinet plan against the install guide for the exact model.

Burner maps: headline figures versus full layouts

The three makers publish burner data at three levels of detail. JennAir and GE print a figure for every position. KitchenAid names three burners with figures and leaves the fourth unstated. A full map lets you plan which pot goes where; a partial map asks you to trust that the unnamed burner is ordinary.

Read the top of the range first. KitchenAid and JennAir both put a 17,000 BTU class burner on a 30 inch surface, which is strong for the size. GE tops out at 11,500 BTU. If your cooking leans on fast boils and hard sears, that gap is the largest single difference between these three cooktops.

Then read the bottom. Every model here publishes a low burner between 5,000 and 5,500 BTU, and the KitchenAid and JennAir add a melt cap at that position. The low end is where sauces, melting and holding happen daily, and all three makers cover it; the separation in this group is at the top, not the bottom.

Three vent figures, three different dialects

The vent numbers in this group cannot be lined up naively. KitchenAid states a 300 CFM exhaust rating. GE states 400 CFM at high speed, with a noise figure of 7.0 sones beside it. JennAir’s listing states a Motor Class figure, and states it two ways on one page: 297 in the feature text and 310 in the spec table.

An exhaust rating and a motor class figure are different descriptions of blower strength, so the honest comparison is a band: all three vents are three-speed systems in the same general strength class, with GE publishing the largest headline number. Duct length and turns in the run will move real performance more than the gaps between these figures.

The sones figure on the GE listing deserves a word, because it is the only noise number in the group. It is stated at high speed, the setting used for a full boil or a sear. The other two makers do not publish a noise figure on the pages read here, so quietness cannot be compared across the three from published data.

Ducted or duct-free in a 30 inch cabinet run

Every model here can vent downward into a duct run, and every model can also convert to duct-free venting, which filters the air and returns it to the room. KitchenAid sells that conversion kit separately, JennAir lists it as an optional kit, and the conversion question belongs in the order, not in the install week.

Ducted venting is the stronger plan where the house allows it, since the air leaves the kitchen entirely. Duct-free is the plan for cabinets on an inside wall or a floor that cannot take a duct. Either way, the vent path is decided by the building first and the cooktop second, and all three models here keep both doors open.

Leave room in the plan for the housing. A downdraft unit is deeper below the counter than a standard cooktop, and a 30 inch cabinet run often holds a drawer stack exactly where the blower wants to sit. The install guide for the chosen model, read before cabinetry is touched, is what keeps that collision theoretical.

Propane conversion, ignition and controls

All three models cover liquid propane. KitchenAid lists an LP conversion kit, JennAir lists LP convertible with the kit included, and GE includes its kit under a published part number, WB28X45706. Conversion is installer work on orifices and settings, so it is booked with the install rather than attempted as a home adjustment.

Ignition is electronic across the group. KitchenAid adds automatic re-ignition, and JennAir lists Flame-Sensing re-ignition, two names for systems that work to relight a burner whose flame goes out. On a surface where the vent draws air past the flames, that feature earns its place on the spec sheet.

Controls differ in placement, which is a daily ergonomic choice. GE puts its knobs at the front center of the surface, JennAir puts metal knobs on the right side, and KitchenAid lists stainless steel knobs. None is better in the abstract; the right answer is the layout your hand already expects from your current cooktop.

FAQ

Five questions round out the picture: whether a fourth model exists anywhere, why the GE burners run lower, which vent figure to trust on the JennAir listing, whether a hood is still needed, and how the finishes of these same platforms should be counted.

Is there a fourth 30 inch gas downdraft cooktop?

No current one that maker or listing pages support. The 30 inch gas downdraft category is the KitchenAid KCGD500GSS, the JennAir JGD3430GS and the GE Profile PGP9830 platform. Other makers sell 30 inch gas cooktops and 30 inch downdraft cooktops, but the overlap of gas and built-in downdraft at this width stops at three.

Older GE downdraft models appear in used listings and old spec sheets, and they are sometimes counted in roundups as if they were current. A model with no current sale page behind it is not a buying option, so this guide leaves those names out of the comparison entirely.

Why do the GE burners run lower than the others?

The published map is what it is: 11,500 BTU at the strongest position, against 17,000 BTU class burners on both rivals. GE pairs that burner set with the strongest published vent figure in the group, 400 CFM, and a glass surface, which reads as a deliberate balance toward venting and everyday cooking rather than peak heat.

Whether that balance suits you depends on your pans. A household whose largest job is a pasta pot and a skillet will not miss the missing output. A household that sears steaks weekly on the cooktop will feel the gap every time, and should weight the KitchenAid or JennAir burner maps accordingly.

Which JennAir blower figure is right, 297 or 310?

The listing page for the JGD3430GS carries both: the feature text describes a 297 CFM Motor Class blower, and the spec table lists CFM Motor Class as 310. This guide counts the spec table as the record and reports the feature-text figure alongside it, because a buyer comparing pages deserves to see the disagreement rather than a tidied number.

Practically, the gap changes nothing in the comparison. Either figure places the JennAir vent in the same band as the KitchenAid 300 CFM exhaust rating, below the GE headline figure, and the installed duct run will matter more than thirteen points either way.

Does a 30 inch downdraft cooktop still need a hood?

The makers build these units to run without one. KitchenAid states its downdraft ventilation needs no separate hood, and the JennAir and GE systems are likewise the whole vent plan for their cooktops. That is the point of the category at this width: a full vent in a 30 inch cutout, with nothing mounted above the surface.

The vent still needs its air path settled, ducted outside or converted to duct-free operation as the buying guide describes. Local building rules can speak to kitchen venting in a given home, so the installer who fits the unit is the right confirmation for your address and your duct plan.

Are the black and stainless finishes separate models?

They are finishes of the same platforms. The JennAir JGD3430GS also appears in black, and the GE Profile PGP9830 appears in stainless as the PGP9830SRSS beside the black PGP9830DRBB covered here. Burner sets and vent hardware stay with the platform; the finish changes the look and the model suffix, not the comparison.

Counted honestly, finishes give a buyer choice without giving the category depth it does not have. Pick the platform on burners, vent and cutout first, then pick the finish that matches the kitchen, and confirm on the listing page that the exact finish suffix is the one being ordered.

Conclusion

Three models are the whole 30 inch gas downdraft field: the KitchenAid KCGD500GSS for named burner strength, the JennAir JGD3430GS for the fullest published figures, and the GE Profile PGP9830DRBB for the strongest vent rating. Measure the cutout, settle the vent path, and choose on the figures that match your cooking.

M
Modern Line Home Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.