Key takeaways
- Five gas cooktops with down vents are sold in 30 and 36 inch widths from KitchenAid, JennAir and GE. Compare burner maps, vent ratings and cutouts by layout.
The whole current category of gas cooktops with down vents holds five models: two at 36 inches with five burners and three at 30 inches with four, from KitchenAid, JennAir and GE Profile. This guide compares all five on burner output, vent ratings and cutout figures, organized by the kitchen each one fits.
Quick verdict
At 36 inches, the KitchenAid KCGD506GSS publishes a 300 CFM exhaust rating and the JennAir JGD3536GS brings sealed brass burners. At 30 inches, the KitchenAid KCGD500GSS keeps the same vent rating in a smaller cutout, the JennAir JGD3430GS prints the fullest figures, and the GE Profile PGP9830DRBB states a 400 CFM vent rating.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| KitchenAid 36 inch 5 Burner Gas Downdraft Cooktop KCGD506GSS | 36 inch gas downdraft | Wide islands and wall runs | 300 CFM exhaust rating, two burners above 15K BTU | Two burner outputs not stated on the maker page |
| JennAir Euro-Style 36 inch JX3 Gas Downdraft Cooktop JGD3536GS | 36 inch gas downdraft | Burner build and low heat | Sealed brass burners, melt cap, JX3 vent | Middle burner outputs not stated on the maker page |
| KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS | 30 inch gas downdraft | Small kitchens that cook hard | Same 300 CFM rating as the 36 inch model | Fourth burner output and dimensions not stated |
| JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS | 30 inch gas downdraft | Replacements planned from print | Full burner map, cutout 28.625 by 19.938 inches | Blower figure stated two ways in listings |
| GE Profile 30 inch Built-In Gas Downdraft Cooktop PGP9830DRBB | 30 inch gas downdraft, gas on glass | Vent strength and printed dimensions | 400 CFM at high speed, full cutout figures | Burner outputs top out at 11,500 BTU |
Five models, three makers, two widths: that is the complete field, and it has been stable across repeated checks of maker lineups. The choice inside it is mostly a layout choice first and a brand choice second, which is how the buying guide below is organized.
How we selected
A model belongs in this guide only if a maker or listing page shows it as a gas cooktop with the down vent built into the same unit, in current sale. Electric downdraft cooktops, induction models with vent pairings and standard gas cooktops that need an overhead hood were all excluded, however often roundups file them under this heading.
The surviving field is five distinct models. Finish variants were counted once: the JennAir 36 inch line also comes in black glass and the GE platform in stainless, and those are finishes of models already counted, not additions to the field. No sixth model from any maker stood up to a page-level check.
Each product section is written from the pages opened for that model across this project: maker pages first, then listings carrying full spec tables. Burner output, vent ratings, fan speeds, cutout figures, weights and conversion notes are quoted as published, and gaps are named as gaps.
Two pages in this set disagree with themselves or with their siblings, and both cases are printed where they occur: one JennAir listing carries two blower figures, and the GE platform’s pages carry different availability signals. Hardware figures are the guide’s subject; availability belongs to the listing on the day of purchase.
Gas cooktops with down vents: the full five-model field
The five sections below run wide to narrow: the two 36 inch models first, then the three 30 inch models. Each one covers the layout it suits, its published burner and vent figures, its conversion paths for propane and duct-free venting, and the limit a buyer should price into the decision.
KitchenAid 36 inch 5 Burner Gas Downdraft Cooktop KCGD506GSS
The maker lists this 36 inch model with five burners and downdraft ventilation that needs no separate hood, over full-width cast-iron grates. It is the wide anchor of the category: the unit an island bench or a long wall run gets planned around when the vent has to live inside the cooktop.
Named burners on the maker page are a 17K BTU Professional Burner, a 15K BTU Professional Burner and a 5K BTU Even-Heat Simmer Burner with a melt cap. Two positions above 15K BTU is the strongest published high end in this guide, and the simmer burner gives the same surface a genuine low end for sauces and melting.
The vent is a 300 CFM exhaust rating worked by a 3-speed fan control. The maker lists electronic ignition with automatic re-ignition, stainless steel knobs, an LP conversion kit, and conversion to duct-free venting with a kit that is not included in the box.
The page leaves two burner outputs unstated and prints no dimension table, so the wide buyer gets the strongest paper on heat and venting and the thinnest paper on fit. The install guide for the model has to close that gap before cabinetry is committed around a 36 inch cutout.
- Pros: strongest published burner pair; 300 CFM exhaust rating; full-width cast-iron grates; melt cap
- Cons: two burner outputs unstated; no dimensions on the maker page; duct-free kit not included
Buy if your layout is a wide island or run and your cooking uses two strong burners at once. Skip if your counter work is already ordered and you need printed cutout figures today; the 30 inch JennAir and GE below publish theirs.
JennAir Euro-Style 36 inch JX3 Gas Downdraft Cooktop JGD3536GS
The maker lists five sealed burners on this 36 inch Euro-Style model, with the JX3 Downdraft Ventilation System handling the vent work. The burners are brass with a removable base, a construction detail that speaks to cleaning and to the long service expected at this end of the market.
Published output names a 17,000 BTU Ultra-High Output Burner and a 5,000 BTU Ultra-Low Output Burner with a Melt Cap. Between those anchors the maker page does not print a full per-burner map for this model, so the middle of the range is described by the platform’s layout rather than by figures a buyer can quote.
The JX3 vent runs three speeds on a 297 CFM Motor Class blower, the maker’s own measure of blower strength. The maker lists DuraFinish Protection on the stainless steel models and lists the cooktop as convertible to duct-free ventilation with an optional kit, with LP conversion covered for propane households.
The same platform is sold in a black glass finish under a sibling model number, and that finish’s printed page adds per-burner figures and dimensions for the black unit. This guide keeps the stainless model’s section to its own page, and counts the two finishes as one model in the field of five.
- Pros: sealed brass burners; melt cap on the low burner; DuraFinish Protection on stainless; black glass finish offered
- Cons: middle burner outputs not stated on the maker page; duct-free kit optional
Buy if burner build and finish choice lead your decision at 36 inches. Skip if you plan the whole purchase from printed figures, because this model’s own page is the thinnest of the five on mid-range data.
KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS
The maker lists this 30 inch model with four burners and the same downdraft approach as its 36 inch sibling, in a stainless unit sized for compact kitchens, galley runs and smaller islands. It is the model that keeps the category open to homes whose cutout stops at 30 inches.
Its named burners match the bigger model’s: a 17K BTU Professional Burner, a 15K BTU Professional Burner and a 5K BTU Even-Heat Simmer Burner with a melt cap. That is an unusual amount of published heat for a 30 inch surface, and it is the reason this model anchors the small end of the guide.
The vent rating also matches the larger unit: a 300 CFM exhaust rating with a 3-speed fan control. Full-width cast-iron grates, stainless steel knobs, electronic ignition with automatic re-ignition, an LP conversion kit and duct-free conversion with a separately sold kit complete the maker page’s list.
As with its sibling, the fourth burner’s output is not stated and no dimension table appears on the opened maker page. Four burners also crowd sooner than five when a stockpot, a skillet and a saucepan all need heat at once, which is the honest size trade a 30 inch buyer accepts.
- Pros: full-size burner names and vent rating at 30 inches; full-width grates; melt cap
- Cons: four burners crowd with large pans; fourth output and dimensions unstated
Buy if your cutout is 30 inches and you cook like it is 36. Skip if three large pans at once is your normal weeknight, because no burner figure fixes a crowded surface.
JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS
Listings for this 30 inch JennAir print the most complete data set in the guide. Four sealed burners are mapped by position: left front 17,000 BTU, right rear 15,000 BTU, right front 10,000 BTU and left rear 5,000 BTU, the last an ultra-low burner with a melt cap.
The hardware list runs long: brass burners with a removable base, DuraFinish Protection, continuous cast iron grates in three sections, metal knobs on the right side, Flame-Sensing re-ignition, and a listing note that the unit stays usable through a power outage. The spec table also marks the model ADA compliant and UL listed.
The JX3 vent runs three speeds. Its blower figure is the one disputed number in this guide: feature text describes a vertically mounted 297 CFM Motor Class blower, while the spec table reads 310. Both are printed here, the table treated as the formal record, because a buyer deserves the disagreement in the open.
Planning figures are complete: width 30 inches, depth 21.5 inches, height 4 inches at the surface, a cutout of 28.625 by 19.938 inches and a net weight of 46 pounds. LP conversion is listed with the kit included, and the maker lists the grates for dishwasher cleaning.
- Pros: full burner map and cutout figures; LP kit included; brass burners; detailed spec table
- Cons: blower figure printed two ways; four burners only
Buy if this is a replacement and the old cutout rules the purchase. Skip if you want the single clean vent figure; the KitchenAid pages state theirs once, in one place, without a rival number beside it.
GE Profile 30 inch Built-In Gas Downdraft Cooktop PGP9830DRBB
The maker page for this GE Profile model describes a 30 inch built-in cooktop with four sealed burners on a gas-on-glass ceramic surface, factory set for natural gas, with front center knob controls and electronic ignition. It is the glass-topped entry in a field of metal surfaces.
Its burner map is printed in full and runs moderate: left front 9,100 BTU, left rear 9,100 BTU, right front 11,500 BTU and right rear 5,500 BTU. Everyday cooking sits comfortably inside those figures; hard searing at the top of the range is where the two rival brands publish more.
The vent is the counterweight: a downdraft exhaust rated 400 CFM and 7.0 sones at high speed, on a variable speed fan with three settings. That is the largest vent figure published in this guide, and the only one paired with a noise rating, which makes this the vent-first choice at 30 inches.
Dimensions are printed in full: 29.75 inches wide, 21.875 deep and 23.875 high including the downdraft housing, with a cutout of 28.75 by 20.5 inches and a net weight of 60 lb. The maker lists medium cast grates and knobs for dishwasher cleaning, an included LP conversion kit under part WB28X45706, ADA compliance and a limited 1-year parts and labor warranty.
- Pros: highest published vent rating; complete dimensions and cutout; LP kit included; warranty stated
- Cons: lowest burner outputs in the group; heaviest at 60 lb
Buy if venting leads and your cooking lives in the everyday range. Skip if a 17,000 BTU class burner is a requirement, because this platform does not publish one in any finish.
Buying guide
With the whole field at five models, the buying work is matching, not narrowing. The sections below match models to kitchen layouts first, then work through burner maps, vent figures, ducting and fuel, the checks that confirm the layout match before money moves.
Matching gas cooktops with down vents to a kitchen layout
Islands are the classic downdraft layout, because a hood over an island interrupts the room and a vent in the surface does not. Both 36 inch models suit a wide island; the 30 inch trio suits a peninsula or a small island where the counter run is shorter and the cook still faces the room.
Wall runs use downdraft when the wall above the cooktop carries windows, tile work or cabinets that a hood would displace. Small kitchens use it to keep one appliance doing two jobs in a 30 inch cutout. Replacement buyers use it when the existing cutout and duct path are already downdraft-shaped, which is the cheapest layout of all.
Every layout shares one condition: room below the counter for the vent housing and its duct. An island with a sink opposite and storage under the cooktop has to give that space to the blower instead. Decide the layout with the cabinet plan open, not after it is built.
Width first: what 30 and 36 inches really change
The width step in this category is also a burner step: 30 inch models carry four burners and 36 inch models carry five. The fifth burner is elbow room more than power, a place to park a pan off the boil or hold a kettle while three positions do the cooking.
Vent strength does not follow width here. The 30 inch KitchenAid publishes the same 300 CFM exhaust rating as its 36 inch sibling, and the 30 inch GE publishes the largest vent figure of the five. A small kitchen gives up a burner, not vent performance, which is the happiest fact in this category.
Cutouts do not scale neatly with nominal width, so measure the hole, not the label. The two 30 inch models that publish cutouts differ from each other: 28.625 by 19.938 inches for the JennAir, 28.75 by 20.5 inches for the GE. Fractions like those decide whether a replacement drops in or the counter gets cut.
Burner maps across the five models
Read across the field and the heat story splits in two. KitchenAid and JennAir publish 17,000 BTU class burners at both widths, with named or mapped 15,000 BTU second positions. GE publishes a full map that tops out at 11,500 BTU. The first group cooks harder; the second vents harder, and the guide does not pretend otherwise.
The low end is uniform and good: every model publishes a burner between 5,000 and 5,500 BTU, and the KitchenAid and JennAir models add a melt cap at that position. Sauces, melting and holding are covered everywhere in this field, so the low end should not drive the choice.
Unstated figures cluster in the KitchenAid pages and the JennAir 36 inch page, which name their anchor burners and leave middle positions unprinted. Where a full map matters to your cooking, the JennAir 30 inch and the GE print one; where it does not, the named anchors are enough to plan around.
Vent figures in three dialects
Three kinds of vent number appear in this guide. KitchenAid states an exhaust rating, 300 CFM at both widths. JennAir states a Motor Class blower figure, 297 on the 36 inch page and either 297 or 310 on the 30 inch listing. GE states an exhaust figure of 400 CFM at high speed, with 7.0 sones of noise beside it.
Exhaust ratings and motor class figures are different descriptions, so the field reads as a band: all five vents are three-speed systems of comparable class, with GE publishing the largest headline number. The installed duct run, its length and its turns, will separate real kitchens more than these labels do.
The sones figure deserves its place. It is the only noise number published in the group, stated at high speed, and it lets a vent-first buyer weigh sound alongside strength for the GE. The other makers publish no noise figure on the pages read here, so quietness beyond that one number cannot be compared from print.
Ducting, duct-free conversion and propane
All five models vent downward into a duct run, and the KitchenAid and JennAir pages list conversion to duct-free venting, with the kit separate in each case. Duct-free operation filters and returns the air, for kitchens where an outside run cannot be built; ducted operation remains the stronger plan where the building allows it.
Propane is covered across the field. KitchenAid lists an LP conversion kit on both of its pages, JennAir lists its 30 inch model as LP convertible with the kit included, and GE includes its kit under a printed part number. Conversion is installer work on orifices and settings, booked with the install.
Both conversions share a timing rule: settle them at ordering. A cooktop delivered before its duct-free kit or its LP kit is arranged is a unit waiting in its box, and the listing page for the exact model suffix is where kit inclusion is confirmed, in print, on the day.
FAQ
Five questions close the guide: whether the field could grow, how the finishes count, which model fits a tall-pot cook, what the disputed JennAir figure means in practice, and which of the five suits a first downdraft purchase, answered from the same published pages as the product sections.
Are there really only five models in this category?
On current maker and listing pages, yes. KitchenAid sells two, JennAir sells two and GE Profile sells one platform at 30 inches. Searches surface other names constantly, and they resolve, page by page, into electric downdraft models, induction units, ordinary gas cooktops with no vent, or discontinued lines in used listings.
The stability of the field is itself a finding of this project: the same five models stood behind this keyword across repeated research passes, and no maker has added a sixth. A buyer can treat the five sections above as the market, not as a sample of it.
Do the black and stainless finishes add more models?
No. The JennAir 36 inch platform comes in stainless and black glass, and the GE 30 inch platform comes in black and stainless. Finishes change the model suffix and the look of the surface; the burner sets and vent systems stay with the platform, so the field stays at five however the finishes are counted.
Finishes still matter at ordering time, because the suffix on the order is the finish that arrives. Choose the platform on layout, burners and vent first, then the finish, then read the listing for that exact suffix before paying, since kit contents and figures are printed per suffix.
Which model suits a cook who uses tall stockpots?
Any of the five carries the same layout fact: a downdraft draws air across the surface, and steam from a tall pot rises higher before it curls toward the vent. That is a trait of the category rather than of one model, and it is worth weighing before choosing downdraft at all for a stockpot-heavy kitchen.
Within the category, published vent strength is the lever you have: the GE’s 400 CFM rating at high speed and the KitchenAid pair’s 300 CFM exhaust rating are the strongest printed figures. Pair either with the high fan setting for tall-pot work, and expect the vent to work harder than it does under a low skillet.
What should a buyer do with the two JennAir blower figures?
Note them and move on. The 30 inch JennAir’s listings print 297 CFM Motor Class in feature text and 310 in the spec table. The gap is small, the spec table is the formal record, and no decision in this guide turns on thirteen points of blower figure either way.
The larger lesson is about listings generally: figures are copied between pages and between sibling models, and a number that appears twice in different forms is a prompt to check the maker’s own spec table. That habit protects every appliance purchase, not just this one.
Which of the five is the simplest first downdraft buy?
The one whose figures you can verify most completely for your layout. For a 30 inch replacement, that is the JennAir JGD3430GS or the GE PGP9830DRBB, both of which print cutouts and full data. For a new 36 inch island, the KitchenAid KCGD506GSS leads on published heat and vent rating, with its install guide supplying the dimensions.
Simple, in this category, means fewest unknowns at install time: cutout confirmed, duct path planned, fuel kit in hand. Rank the five by those three checks for your kitchen and the shortlist orders itself, whichever brand ends up on top.
Conclusion
Five models are the whole of this category, and they divide cleanly: KitchenAid for published heat at both widths, JennAir for burner build and printed detail, GE Profile for the strongest vent figure. Start from your layout and cutout, and the right one of the five names itself quickly for most kitchens.