Updated Nov 16, 2026· 16 min read

Key takeaways

  • Compare six tapes for writing channel names on mixers, from flatback paper console tape to matte gaffer, with maker specs on adhesion, width and clean removal.

Channel strips get relabeled every time the lineup changes, and the wrong tape leaves glue on the fader panel or ink that smears at the first touch. This guide compares tape for writing channel name on mixers using maker data sheets only, covering flatback paper rolls and matte cloth gaffer rolls side by side.

Quick verdict

For a dedicated strip label, flatback paper is the cleaner tool: Pro Tapes Pro Console Tape is made for sound and lighting boards, takes pen and marker, and lifts off without staining or ghosting. If one roll must also hold cables and mark cases, a matte white gaffer such as the Gaffer Power roll is the flexible pick.

Product Type Best for Key spec Main limit
Pro Tapes Pro Console Tape Flatback paper Dedicated channel strip labels Adhesion to steel 57 oz per inch Maker sheet does not state roll width or length
Pro Tapes Pro Artist Tape Flatback paper Boards plus layout and masking work Repositionable clean removal adhesive Maker page does not publish numeric specs
3M Scotch Printable Flatback Paper Tape 256 Flatback paper Color coding in red, white and green Standard roll 1 inch by 60 yards Maker says keep it away from outdoor exposure
Gaffer Power Professional White Gaffer Tape Matte cloth gaffer Labels plus cable and case duty Roll 2 inches by 30 yards Wider than a typical channel strip
Pro Tapes Pro Gaff Matte cloth gaffer Crews that label cases and mark sets Adhesion to steel 75 oz per inch Firmer grip than a strip label needs
Shurtape P-665 Matte cloth gaffer Heavy holding with a writable white roll Adhesion to stainless steel 80 oz per inch Standard widths start at 48 mm

How we selected

Every roll here was read on an opened maker page or maker data sheet, and only facts printed there are used: backing, adhesive type, adhesion and tensile figures, thickness, colors and stated applications. Rolls the maker aims at board labeling come first; gaffer rolls qualify only when the maker describes a matte, writable surface or labeling use.

The split that matters is paper against cloth. Flatback paper gives a smooth writing face and a light, repositionable hold that suits a strip you peel off after the show. Cloth gaffer gives a stronger hold and a tougher roll that also tapes cables down, at the cost of a wider strip and a textured writing face. Neither family is wrong; the right pick depends on whether the roll lives on the console or in the workbox.

Sizes are quoted only where the maker states them. One maker sheet below gives full technical data but no roll dimensions, and that gap is flagged in its section instead of being filled in from a listing. Where two maker documents disagree on a number, the technical data sheet figure is the one used and the disagreement is noted in the product section.

Tape for writing channel name on mixers: the six rolls in detail

Six rolls follow: three flatback paper tapes built for labeling and three matte cloth gaffer tapes that can carry a channel name as a second job. Each section states who the roll suits, the maker figures behind it, and the limit that should rule it out for some buyers.

Pro Tapes Pro Console Tape

This is the one roll in the group the maker aims straight at the job: the data sheet calls it a premium flatback paper tape and lists sound and lighting boards as the ideal use. For engineers who relabel the same console every night, it is the default starting point of the six.

The backing is flatback paper with a synthetic rubber adhesive and no silicone present. The maker rates tensile strength at 30 pounds per inch, elongation at 2.5 percent, total thickness at 5.8 mils and adhesion to steel at 57 oz per inch, with a service temperature range of 40 to 150 degrees F. The sheet lists eleven colors: green, orange, blue, white, yellow, black and red, plus fluorescent pink, orange, green and yellow.

Writing is the strong point. The maker lists the tape as printable with pen or Sharpie and with flexo inks, markers, pens and pencils, so a fine marker line stays where you put it on the smooth paper face. The adhesive is repositionable, removes cleanly and, in the maker’s words, will not stain or ghost after removal; the white roll is pH neutral. The sheet also lists ASTM D6123 Type II and ASTM D-4236, with the fluorescent colors excepted from the second standard.

Pros: a board-specific product with a full published data sheet; a smooth paper face that takes fine marker lines; repositionable adhesive for strips that move between shows; eleven colors for section coding. Cons: the maker data sheet does not state roll width or length, so size has to be confirmed on the listing page before ordering; paper will not double as a cable hold-down roll the way cloth does. Buy if the roll lives on the console. Skip if you need one roll for floors and cables as well.

Pro Tapes Pro Artist Tape

Pro Artist is the maker’s broader flatback line, described as a premium flatback paper tape used for marking and masking boards, color coding and labeling. It suits buyers who label a mixer at the weekend and tape down layouts, artwork or set plans during the week with the same roll.

The maker describes a repositionable, clean removal adhesive system that does not leave residue, removes cleanly from sound and lighting boards and will not stain or ghost after removal. The tape is printable with flexo inks, markers, pens and pencils, and the maker credits it with good tensile strength, high edge tear resistance and easy unwind. The adhesive is the maker’s synthetic rubber adhesive technology, and the white roll is pH or acid neutral.

That edge tear resistance matters on a strip label: a strip that frays at the corners starts to lift, and lifted corners catch sleeves and cloths during a show. Easy unwind matters too, because strip labels are usually torn and written in a hurry between soundcheck and doors. The maker’s copy positions Artist and Console as close relatives, and in practice the Artist line is the one sold for general marking work beyond the board.

Pros: the same clean removal behavior as the console line; a smooth, printable paper face; strong edges for a thin paper tape. Cons: the opened maker copy does not publish numeric adhesion, tensile or thickness figures, so there is no printed number to compare against the console sheet; the line is aimed at art and layout buyers as much as at audio crews. Buy if one paper roll covers boards and layout work. Skip if you want the fully documented board-specific sheet.

3M Scotch Printable Flatback Paper Tape 256

The 256 is the industrial entry: a colored flatback paper tape from 3M that the maker describes as easily marked and written on, and ideal for labeling and coding applications. It suits a venue or install team that already orders industrial tape and wants one documented roll for mixer strips and rack labels alike.

3M’s technical data sheet lists a colored flatback paper backing with a rubber adhesive, in red, white and green. Total thickness is 4.8 mils, peel adhesion is 35 oz per inch, tensile strength is 32 pounds per inch and elongation at break is 3.5 percent, with short term temperature resistance up to 200 degrees F and a standard roll length of 60 yards; the product page lists a 1 inch width. One note: the 3M product page headline gives a 6.7 mil figure, while the current data sheet gives 4.8 mils; the data sheet value is the one used here.

The maker lists marking with ballpoint pens, felt-tip pens, pencils and rubber stamps, plus printing with standard flexographic inks, and says the tape detaches easily and provides clean removal from a variety of substrates. The backing tears by hand while minimizing slivering. Adhesion at 35 oz per inch is the lightest printed figure in this group, which is a plus for strips on painted or screened panels that get relabeled often.

Pros: fully documented by the maker, including test methods; the lightest adhesion here for frequent relabeling; three colors for coding; a long 60 yard standard roll. Cons: 3M states the tape should not be subjected to outdoor exposure and labels it for industrial and occupational use; the color range is narrower than the Pro Tapes paper rolls. Buy if documented specs and gentle adhesion matter most. Skip if you need fluorescent colors or a board-specific product.

Gaffer Power Professional White Gaffer Tape

This woven cotton cloth roll is the gaffer entry the maker itself points at consoles: the product page names labeling channel strips on mixing consoles as a use, and calls the matte white surface the pro’s choice for that job. It suits a small crew whose single white roll labels the board, the wireless transmitters and the cases.

The roll is 2 inches wide and 30 yards long. The backing is woven cotton cloth with a matte, non-reflective finish, and the adhesive is a specialized rubber adhesive that the maker describes as peeling off clean with no residue left behind. The maker states the surface is designed to take ink from permanent markers and pens without smudging, and that the high thread count cloth tears by hand in both directions for fast strips. The maker also states the tape is made in the USA.

Width is the trade. Two inches is far wider than a channel strip, so in practice the roll gets torn lengthwise or used for wide scribble areas on larger desks, case labels and transmitter tags where the space exists. The matte cloth face will never be as smooth as paper under a fine marker, but the maker designed the surface for ink, and the same roll can seam a floor or hold a cable run when the show is over.

Pros: the maker explicitly designs and markets the surface for console labeling; cloth toughness for case and floor duty; clean removal claims from the maker; tears straight by hand. Cons: no tensile, thickness or adhesion figures are published on the opened maker page; the 2 inch width needs managing on narrow strips. Buy if one white roll must cover labeling and general production work. Skip if the roll is only for channel strips, where paper is neater.

Pro Tapes Pro Gaff

Pro Gaff is the maker’s long-running matte cloth gaffer, and its data sheet lists marking and labeling equipment cases among its applications. For a touring engineer, that makes it the roll that names the console strip tonight and the road case tomorrow, with twenty colors to code a whole system.

The sheet lists a cotton cloth backing with a synthetic rubber based adhesive, total thickness of 11 mils, tensile strength of 50 pounds per inch, adhesion to steel of 75 oz per inch, elongation of 4 percent and a service temperature range of 50 to 180 degrees F. Features the maker lists include high thread count, hand tearable, abrasion resistant, weather resistant and clean removability from most surfaces, with fluorescent colors described as UV light friendly for high visibility.

On a mixer, the white roll is the labeling candidate: a matte cloth face that takes marker, on a strip that will also survive being used as a hold-down. The twenty colors, which run from black, white and gray to chroma green and four fluorescent shades, are aimed at stage marking and case coding rather than at channel names, where white under a dark marker reads best. Adhesion of 75 oz per inch is a firm grip for a strip you plan to peel nightly, so paper stays the gentler choice for delicate panel finishes.

Pros: the strongest documented all-round cloth roll here; twenty colors; weather resistance for outdoor shows; a full maker data sheet. Cons: adhesion is high for a temporary strip label; the maker sheet does not state roll width or length; cloth texture is coarser to write on than flatback paper. Buy if the labeling roll also works as your main gaffer. Skip if strips go on a finished panel you worry about.

Shurtape P-665

The P-665 is the gaffer standard from Shurtape, listed for demanding applications that require clean removal in the audio and visual, television, photography, theatrical and motion picture industries. It suits a production sound department that already stocks it for wiring and props and wants the white roll to double for board labels.

The maker’s data sheet lists a matte finish coated cloth backing with a synthetic rubber adhesive. Tensile strength is 50 pounds per inch width, adhesion to stainless steel is 80 oz per inch width, thickness is 11.5 mils, elongation is 4 percent and the service temperature range is 50 to 180 degrees F. Standard widths are 48 mm and 72 mm on a 55 m roll with a 3 inch core, the sheet lists white and gray, and the tape meets CID A-A-1586A.

The maker lists high adhesion and tack, a conformable build, hand tearing in both the machine and cross directions, and clean removal from most surfaces. That is a holding specification first and a labeling specification second: nothing on the sheet speaks to printability, so names go on the matte white cloth with a marker as a working practice rather than a maker promise. The narrowest standard width, 48 mm, is about twice a typical strip, so strips get split or the tape serves on wider surfaces.

Pros: the highest adhesion figure in this group for strips that must not move; a documented professional standard; clean removal from most surfaces per the maker. Cons: built for holding wiring, lighting and props, not for labeling; standard widths start wide for channel work; no writing or printing claim on the maker sheet. Buy if your department already trusts this roll and wants one tape for everything. Skip if labeling is the main job.

Buying guide

Choosing between these rolls comes down to four questions: paper or cloth, how strong the adhesive is, what width the strip space allows, and how the writing surface behaves under your marker. The sections below take each question in turn, using the maker figures from the product sections as the reference points.

Paper or cloth: the first call for tape for writing channel name on mixers

Flatback paper is the purpose-built answer: a face that takes a fine marker line, a light repositionable hold, and a strip that peels away after the show. Cloth gaffer is the generalist: tougher, weather resistant and strong enough to hold cables, with a textured face that writes less neatly. Most engineers who label every night end up on paper.

The working pattern that suits many crews is one of each. A paper roll lives at the console for strips, and a white cloth roll lives in the workbox for cases, cables and the wide labels on outboard racks. That pairing avoids the two failure modes: paper torn apart on floor duty, and strong cloth adhesive sitting on a channel strip for a month because the strip was never swapped.

Adhesion, tack and clean removal

The adhesion figures in this group run from 35 oz per inch on the 3M paper tape to 80 oz per inch on the Shurtape cloth roll, and that spread is the whole story. Low figures suit strips that change nightly and panels with printed legends you want to protect. High figures suit a strip that must survive a tour leg without lifting at the corners.

Clean removal is a separate claim from adhesion, and every maker here makes it in some form: repositionable paper adhesives that will not stain or ghost, and cloth adhesives the makers describe as removing cleanly from most surfaces. Long dwell time is the enemy of both, so the practical rule is to date strips mentally and swap them at each production change rather than leaving any tape on a panel for a season.

Width and roll length

Strip space sets the width. The 3M roll is listed at 1 inch wide on a 60 yard roll, the Gaffer Power roll is 2 inches by 30 yards, and the Shurtape standard widths start at 48 mm. A wide roll is not wasted on narrow strips: it can be torn lengthwise, and the remaining width covers case labels and rack tags that a narrow roll handles badly.

Length decides how often the spare roll matters. A 60 yard paper roll covers a lot of soundchecks, while a 30 yard cloth roll that also seams floors disappears quickly. Where a maker sheet does not state roll size, as with the two other Pro Tapes rolls here, confirm the size on the listing page before ordering rather than assuming the family standard.

Color coding a full board

Color earns its place when board sections need to read at a glance: drums in one color, guitars in another, vocals in a third. Pro Console lists eleven colors with four fluorescent shades, Pro Gaff lists twenty, and the 3M 256 keeps red, white and green. For the names themselves, white under a dark marker still reads best.

Two cautions from the maker sheets: the white rolls are the ones listed as pH neutral on the paper tapes, and the fluorescent Pro Console colors are the ones excepted from the ASTM D-4236 listing. If a strip will sit on a panel for weeks, white paper is the conservative choice; save the bright colors for show-day strips and case coding that comes off sooner.

Markers, pencils and the writing surface

The paper makers list their writing tools outright: markers, pens and pencils on the Pro Tapes sheets, and ballpoint pens, felt-tip pens, pencils and rubber stamps on the 3M documents. A fine permanent marker is the standard choice because the ink dries fast and resists the smear of a sleeve brushing the strip mid-show.

On cloth, only the Gaffer Power page makes a writing claim, describing a surface designed to take marker and pen ink without smudging. The other cloth makers are silent on writing, so treat cloth as a surface that accepts a bold marker line rather than fine print. Small handwriting belongs on paper; big block letters for case and rack labels are where cloth earns its keep.

FAQ

Five questions come up whenever engineers compare these rolls: width against strip space, paper against cloth, how long a strip can stay on a panel, which colors to use, and what to do when only gaffer is in the box. Each answer below stays with the maker figures and general practice, with no hands-on claims.

How wide should tape for writing channel name on mixers be?

Match the strip to the scribble space above or below the faders, which on most desks takes a strip around an inch tall or less. The 1 inch 3M roll fits that space as sold. Wider cloth rolls, 2 inch and 48 mm here, can be torn lengthwise into two strips, and the spare width is useful for case labels where more writing room helps.

Is paper tape or gaffer tape better for channel labels?

For the label itself, paper: flatback makers list board labeling as the application, use repositionable adhesives for the job, and offer smooth faces that take fine marker lines. Gaffer wins when one roll must also hold cables, survive weather and take rough handling, and matte white gaffer works as a label surface when paper is not at hand.

How long can a strip stay on the mixer?

No maker here prints a maximum dwell time for a channel strip, so treat figures heard elsewhere with care. The sheets say these adhesives are built for clean removal, and two paper makers add storage guidance of use within 12 months. The habit is simple: replace strips at every production change, and never let one bake through a long residency.

Which color should channel names be written on?

White, in almost every case: the paper makers single out the white roll as pH neutral, and dark marker on white reads under both house light and stage wash. Use the colored and fluorescent rolls for section coding, case coding and marks that need to shout, and keep the names on white so a substitute engineer can read the board at a glance.

Can I write on gaffer tape with a normal marker?

Yes, within limits. The Gaffer Power page states its matte white surface is designed to take permanent marker and pen ink without smudging, and matte cloth accepts a bold marker line. Fine print is where cloth loses out: the woven texture spreads a fine line, so keep cloth labels to short names in larger letters and put detailed strips on paper.

Conclusion

For channel names, buy the paper first: Pro Console Tape is the board-specific roll with the fullest maker data behind it, and Pro Artist covers the same ground for general marking. Keep a matte white gaffer in the workbox for cases and cables, and let each roll do the job its maker built it for, night after night.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.