Key takeaways
- Six noise gate pedals for mixer channels compared, from the Boss NS-2 and MXR Smart Gate to the Fortin Zuul+, with loops, key inputs, modes and power needs.
A noisy guitar rig hands the mixer a problem it cannot fix at the fader, so the best noise gate for mixers is the pedal that silences the rig itself: it mutes hiss, hum and pedal noise between notes, then opens again the instant playing starts. These six pedals cover every common board layout and price point.
Why the gate belongs before the mixer
A mixer channel can only work with what arrives at its input. When a high-gain guitar rig sends hiss, hum and pedal noise down the cable along with the music, the fader raises and lowers both together, and every pause in the song fills with noise that the whole audience hears through the main speakers.
A gate pedal fixes the problem at the source. It sits in the instrument’s own chain, watches the signal, and closes when playing stops, so the channel feeding the mixer carries silence between songs and between phrases. The sound engineer gets a clean input to work with, and the player keeps the gain and sustain the rig was built for.
Placement decides how well any gate works. A pedal at the end of a board hears the summed noise of everything before it, a pedal with a loop or a key input can listen to the clean instrument while it gates the noisy part of the chain, and a pedal inside an amplifier’s effects loop can quiet the preamp as well. The six pedals below cover all three layouts, which is why the loop and key columns in the comparison table matter.
On stage the gated signal reaches the mixer two ways: from a DI box after the pedalboard, or from a microphone on the amplifier. The gate helps both. The DI feed arrives clean because the board went quiet between songs, and the microphone hears an amp whose idle hiss has stopped, so the engineer is not forced to ride the fader down during every pause or mute the channel and risk missing the first note back in.
What to look for in a noise gate for mixers
Three things separate a gate that disappears into the music from one that fights the player: how its threshold and decay are shaped, whether it can listen to a clean signal through a loop or key input, and how it behaves on a working pedalboard in bypass and on the power supply.
Threshold, decay and reduction depth
The threshold sets the level where the gate opens, and decay or release sets how the sound fades as it closes. A gate for a mixer channel has to open on quiet picking as reliably as on full chords, because the channel records or broadcasts whatever the pedal passes, including a note whose front edge the gate clipped off.
Depth matters too. Electro-Harmonix prints a reduction range for The Silencer from -70dB at full clockwise to +4dB at the other end, so the same pedal can mute a channel outright or merely drop its noise floor by a few decibels. TC Electronic gives the Sentry a Damp knob for the same job, while the Boss NS-2 and Behringer NR300 keep the simpler threshold-and-decay pairing that most players learn first.
Loops and key inputs
A loop or key input lets the gate listen to the clean instrument while it gates the noisy signal, and that split is the difference between a gate that tracks playing dynamics and one that guesses. Put the noisy drive pedals inside the loop, and the detector still hears the dry guitar, so a soft note opens the gate even while the loop hisses.
Boss builds the loop into the NS-2 as send and return jacks, Electro-Harmonix gates a whole effects loop with The Silencer, and TC Electronic adds a send and return to the Sentry. Fortin takes the idea furthest on the Zuul+: a Key In jack takes the clean signal, and a Key Thru passes it on with a ground lift switch, so no separate splitter pedal is needed on the board.
Bypass and power on a working board
A gate sits in the chain all night, so bypass decides what the mixer hears when the gate is off. The MXR Smart Gate and the Fortin Zuul+ use hardwire or true bypass switching, the Boss NS-2 and The Silencer use buffered bypass, and the Sentry offers true or buffered bypass on an internal switch, which suits long cable runs.
Power draw decides whether a board supply has a spare outlet with enough current. The Silencer draws 22 mA and the NS-2 draws 25 mA, both easy loads, the Zuul+ draws 40 mA and runs on a supply only with no battery option, and the NS-2 answers back with battery life figures of about 24.5 hours on an alkaline battery plus a DC output that can feed other pedals.
The six pedals compared side by side
The table lines the six pedals up on the points that decide a purchase: the controls on the top panel, whether the gate can listen through a loop or a key input, the bypass type, and what it draws from the power supply. The sections after the table take each pedal in turn.
| Pedal | Controls | Loop or key input | Bypass | Power |
|---|---|---|---|---|
| Boss NS-2 Noise Suppressor | Threshold, Decay, Mode | Send/return loop | Buffered | 25 mA, battery or adaptor |
| MXR Smart Gate M135 | Threshold, mode selector | None printed | Hardwire (true) | 9V battery or supply |
| Electro-Harmonix The Silencer | Threshold, Reduction, Release | Send/return loop | Buffered | 22 mA, battery or supply |
| TC Electronic Sentry | Threshold, Damp, Decay | Send/return loop | True or buffered, selectable | 9V DC supply or battery |
| Behringer Noise Reducer NR300 | Threshold, Decay, Mode | None printed | Not printed | 9V battery or supply |
| Fortin Zuul+ | Threshold, Hold, Release | Key In and Key Thru | True (3PDT) | 40 mA, supply only |
Read the loop column first if the rig runs several drive pedals, because a gate that can isolate them will always track better than one listening to their combined hiss. Read the controls column first if the player changes styles mid-set, because a pedal with a mode switch or a reduction knob adapts faster between songs.
The six also split by philosophy. Three of them, the NS-2, the NR300 and the Smart Gate, ask the player to set a threshold and a fade and then leave the pedal alone. The other three, The Silencer, the Sentry and the Zuul+, hand over deeper control of depth, bands or key routing for rigs whose noise changes with every song.
A noise gate for mixers, pedal by pedal
Every figure below comes from the maker’s own page or manual, opened and checked for this guide. The order runs from the long-running workhorse pedals to the specialist high-gain tool, and each entry covers the controls, the routing and the rig the pedal suits best.
Boss NS-2 Noise Suppressor
The NS-2 is the pedal most boards know: a compact noise suppressor for guitar and bass with Threshold and Decay knobs and a mode switch. Boss builds it around a VCA with high-speed envelope detection, and prints a nominal level of -20 dBu with a 1 M ohm input impedance, figures that sit happily in front of an amp or a mixer channel’s DI feed.
Its send and return loop is the reason it stays on professional boards. Drive and gain pedals sit inside the loop, the detector keeps reading the clean input, and the loop’s noise is suppressed without the gate losing track of quiet playing. Reduction mode switches the suppression with the footswitch, while Mute mode toggles between suppression and full silence for tuning and guitar changes mid-set.
The details suit working players: buffered bypass, a current draw of 25 mA, about 24.5 hours of playing on an alkaline battery, and a DC output jack that can pass power on to other pedals with the maker’s parallel cable. The case measures 73 by 129 by 59 millimeters and weighs 415 grams with the battery. For a mixer channel fed by a changing cast of guitar rigs, the NS-2 is the default answer.
MXR Smart Gate M135
The Smart Gate takes a different route to the same silence: instead of a loop, MXR gives it three selectable types of noise reduction named Hiss, Mid and Full, so the gate can concentrate on the band where the rig’s noise lives. A single threshold trigger control sets the opening level, and the circuit judges both when and how fast to engage.
That speed judgement is the pedal’s point. MXR’s copy stresses that the gate senses the playing and stays out of the way of sustain, so a held chord rings out and decays on its own terms instead of being chopped at the tail. For a mixer channel carrying a lead player who leans on long notes, that behavior keeps the gate inaudible in the mix.
The M135 uses hardwire bypass, so the signal passes untouched when the pedal is off, and it powers from a 9-volt battery or from MXR’s own ECB003 adapter and Brick-series supplies. It is the simplest pedal in this group to set: choose the noise type that matches the rig, turn the threshold until the noise stops, and play. Small boards and players who dislike menus get the most from it.
The three modes earn their keep across a night. Hiss suits the high, thin noise of an amplifier idling under gain, Mid suits the hash a chain of pedals builds in the middle of the spectrum, and Full takes on broadband noise from a whole rig. Switching modes at soundcheck takes a second, and the mixer downstream hears the difference as a channel that simply goes quiet when the song ends.
Electro-Harmonix The Silencer
The Silencer is the thinker’s pedal in a small box: three knobs for Threshold, Reduction and Release, and a gated loop that swallows a whole pedal chain. The manual prints the Reduction range from -70dB at full clockwise to +4dB at full counter-clockwise, so it can also work as a gentle downward expander that only lowers the noise floor.
Release runs from a quick 8 milliseconds to a slow 4 seconds, the widest printed span in this group, so the same pedal snaps shut behind a metal riff and drifts closed behind a ballad. Used inline it gates the instrument alone; used with its loop it gates everything inside the loop while the detector reads the input, and the loop stays in the signal path even in bypass.
The printed electrical figures are tidy: 2 M ohm input impedance, 300 ohm output impedance, a 1 M ohm return input, and a draw of 22 mA at 9 volts from a battery or the maker’s supply. Buffered bypass keeps long cable runs to the mixer from dulling the top end. For a player who wants one pedal to tame a whole board and likes turning knobs until the gate vanishes, The Silencer is the pick.
TC Electronic Sentry Noise Gate
The Sentry is the digital entry in the group, a multiband gate built on the algorithms from TC’s System 6000 processor. It gates three independent frequency ranges, so low hum, midrange hash and high hiss each get their own threshold behavior, and a note’s decay sounds natural because the bands close at different rates rather than all at once.
Three modes sit on a toggle: the multiband mode for general rig noise, a classic hard gate mode that cuts in the abrupt style modern metal players use for tight stops, and a TonePrint mode that loads settings from the TonePrint Editor on Mac, Windows or iPad, including artist presets and deep parameter edits that the three knobs cannot reach.
The panel keeps Threshold, Damp and Decay knobs, where Damp sets how far the signal drops when the gate closes, and a send and return loop isolates the noisy pedals or accepts an external trigger. Bypass is selectable between true and buffered on an internal switch. For a mixer channel that must handle several different rigs in one show, the Sentry’s presets and multiband behavior adapt the fastest.
Behringer Noise Reducer NR300
The NR300 is the budget pedal of the group, built around the familiar control layout: Threshold and Decay dials plus a mode switch. In Reduction mode the dials set where the gate opens and how it closes, and Behringer’s own copy leads with the single-coil player, the guitarist who loves single-coil snap and hates the 60-cycle hum that rides along.
Mute mode turns the pedal into a quiet on/off switch for the instrument, which covers silent tuning and guitar swaps without a separate mute box on the board. Two LEDs show when the pedal is active and when it is actively suppressing noise, a small detail that helps on a dark stage when the engineer asks whether the gate is the reason a channel went quiet.
Power comes from a 9-volt battery or the maker’s PSU-SB supply. Nothing about the NR300 reaches for the specialist features of the Zuul+ or the Sentry, and that is its place in the list: a first gate for a home board, a spare for the gig bag, or the pedal that quiets a rehearsal-room rig feeding a small mixer, at the lowest cost of the six.
Fortin Zuul+
The Zuul+ is the high-gain specialist, built around one idea executed thoroughly: the gate itself sits after the gain stages, where the noise is, but it takes its orders from the clean guitar signal through a Key In jack. A Key Thru output with a ground lift switch passes that clean signal onward, so no external splitter is needed.
The Zuul+ adds Hold and Release controls over the original Zuul, alongside the threshold control, so the player shapes how long the gate waits and how it lets go. It supports two-, three- and four-cable methods, which covers a pedal in front of the amp, a pedal in the loop keyed from the guitar, and full rigs that do both at once, and the ground lift answers the loops that hum in three- and four-cable setups.
Switching is a 3PDT true bypass stomp, power is a 9 to 12 volt DC supply at 40 mA with no battery option, and the case measures 112 by 60 by 27 millimeters before knobs and switches. It is built in the USA. For the mixer, a Zuul+ on the heaviest rig on stage means the loudest channel also becomes the quietest one between riffs.
Matching the pedal to the rig
The best choice follows the noise, not the brand. High-gain rigs need keyed or looped detection, single-coil and bass rigs need a gate that respects quiet dynamics, and a board that travels needs power and bypass choices that survive a different backline every night.
High-gain guitar rigs
Gain multiplies everything, including the noise floor, so a high-gain channel reaches the mixer carrying hiss that a plain end-of-chain gate struggles to judge. The detector hears the hiss as signal, the threshold has to rise, and quiet playing starts to disappear along with the noise it was meant to keep.
Keyed and looped pedals break that trade. The Zuul+ listens to the clean guitar through its Key In while gating after the gain, the NS-2 and The Silencer put the gain pedals inside a loop under the same logic, and the Sentry’s hard gate mode answers with the abrupt cut that tight rhythm playing uses as an effect in its own right.
Setting any of them follows the same soundcheck routine. Play the quietest part of the set, turn the threshold up from its lowest point until the noise stops, then play the loudest part and check that nothing at the front of the notes went missing. A gate set in an empty room at full volume will behave differently once the band is playing, so the final check belongs in the last song of the soundcheck, with the mixer channel open at show level.
Bass and single-coil noise
Bass rigs and single-coil guitars make a different kind of noise: hum and buzz at a steady level under notes that are themselves quiet and long. A gate set for a loud guitar rig will eat the tail of a bass note, so the decay control and a partial reduction setting matter more than raw closing speed here.
The Silencer’s reduction range, which can stop well short of a full mute, and the Sentry’s Damp knob both let the player lower the hum without silencing the instrument between phrases. The NR300 speaks directly to the single-coil player in its maker’s copy, and the NS-2’s decay knob, turned toward longer times, keeps bass notes sounding natural into the mixer.
Boards that travel
A touring board meets a different mixer, a different power circuit and a different stage every night, so the gate has to adapt quickly and fail gracefully. Battery figures matter when a supply outlet dies: the NS-2 prints about 24.5 hours on alkaline, and the Silencer and NR300 both run on a plain 9-volt battery as a fallback.
Bypass choice matters for the same reason. Buffered pedals such as the NS-2 and The Silencer protect the top end across long cable runs to a distant desk, while the Sentry’s switchable bypass lets the player match the pedal to the venue’s cabling. The Zuul+ asks for a supply and gives back the ground lift, which solves the hum that appears only in certain buildings.
For most boards the short list is short: the Boss NS-2 for the loop and the track record, The Silencer for the widest control ranges, the Sentry for multiband gating and presets, the Smart Gate for three-knob simplicity, the NR300 for the lowest cost, and the Zuul+ when a high-gain rig needs keyed gating done properly.