Updated Nov 16, 2026· 14 min read

Key takeaways

  • Compare six hardware audio gates for mixers, from the Drawmer DS201 and dbx 1074 to the Klark Teknik SQ1D, with key filters, envelope controls and formats.

The best audio gates for mixers sit in the rack beside the console and keep quiet channels quiet: they hold back the bleed, hiss and spill that collect around a channel while it sits silent, then open in microseconds when the real signal arrives. These six hardware units cover two to eight channels at a time in a standard equipment rack.

What an audio gate does on a mixer channel

A gate is a switch that listens to one channel and opens only when the signal rises above a level you set. Below that threshold the channel is turned down or muted, and above it the signal passes at full level, which is why gates earn their keep on busy stages and drum kits.

Most consoles route an outboard gate through the channel insert point, so the gate hears the microphone signal before the fader and the channel EQ. Some engineers patch gates across subgroups instead, but one gate per problem channel is the usual layout, because each microphone picks up a different mix of the wanted sound and everything else in the room.

The classic jobs are easy to picture. A tom microphone hears the whole kit, yet it only needs to speak when its own drum is hit. A guitar amp channel carries hiss and hum between songs. A vocal microphone on a loud stage collects cymbals and monitor spill whenever the singer pauses. In each case the gate holds the channel down during the gaps and opens for the part that matters.

A gate is not a cure for a bad microphone position, and it cannot separate two sounds that arrive at the same moment. What it removes is the noise that lives between the notes: the ring, the spill and the hiss that stack up across sixteen open microphones and turn a mix muddy. Used with a sensible threshold, it cleans the spaces without touching the performance itself.

One behavior separates a good gate from a frustrating one: what it does at the threshold line itself. A signal that hovers right at the trigger level can make a simple gate open and close several times a second, a flutter engineers call chatter. Makers answer it with hold time, with hysteresis that moves the closing point below the opening point, or with both, and the units below use all three answers in different combinations.

What to look for in audio gates for mixers

Three groups of controls decide how a gate behaves: the threshold and how far the channel turns down, the key filters that decide what the gate listens to, and the envelope controls that shape how it opens and closes. The six units in this guide divide those jobs in different ways.

Threshold, depth and range

The threshold sets the level a signal must cross before the gate opens, and the range, depth or floor control sets how far the channel drops when the gate is closed. A full close suits a tom channel, while a partial drop of 20 dB often sounds more natural on a vocal that should never vanish completely.

Look at how wide the threshold range runs, because quiet sources such as acoustic instruments need a gate that still triggers reliably at low levels. The Drawmer DS201 sets its threshold from -50dB up to infinity, and the dbx 1074 gives each of its four channels its own threshold and depth controls, so a loud snare and a quiet floor tom can share one unit without sharing settings.

Key filters and key listen

A key filter tunes the gate’s detector to one band of frequencies, so the gate opens for the sound you want and ignores the spill you do not. A key listen switch sends that filtered detector signal to the output while you set up, which turns a guessing game into a thirty-second job of turning two knobs until only the wanted drum remains.

Drawmer built its name on this idea and calls it frequency conscious gating: the DS201 carries separate high-pass and low-pass key filters, the MX40 uses a single trigger frequency control with a one-octave band, and the DS101 module keeps the two-filter layout in a 500-series slot. The dbx 1074 takes a similar path with a key filter on each channel that sweeps from 80Hz to 8kHz.

Attack, hold and decay

Attack sets how fast the gate opens once the signal crosses the threshold, hold keeps it open for a set time after the signal drops, and decay or release shapes how it fades shut. Fast attacks in the microsecond range keep the front edge of a drum hit intact, while hold and decay stop the gate chattering on signals that hover near the threshold.

The envelope ranges differ more than the brochures suggest. The DS201 attacks in as little as 10 microseconds and holds for up to 2 seconds, the DS101 matches those figures in module form, and the dbx 1074 uses an accelerating release that starts slowly and speeds up, which helps long tom decays fade without an audible chop at the end.

The six gates compared side by side

The table below lines up the six units on the points that decide a purchase: how many channels each one gates, the format it occupies, and how its key filtering works. Full control ranges and the jobs each unit suits best follow in the product sections after the table.

Product Channels Format Key filtering Standout control
Drawmer DS201 Dual Noise Gate 2 1U rack High-pass and low-pass key filters Gate or duck modes, range to 90 dB
dbx 1074 QuadGate 4 1U rack Key filter 80Hz to 8kHz per channel Depth control and accelerating release
Klark Teknik Square ONE Dynamics SQ1D 8 3U rack Band-pass sidechain filter per channel Each channel gates or compresses
dbx 1066 Compressor/Limiter/Gate 2 1U rack External sidechain with monitor switch Expander/gate ratio to 30:1
Drawmer MX40 Punch Gate 4 1U rack Trigger frequency 50Hz to 8kHz Peak Punch transient lift, 3 knobs per channel
Drawmer DS101 Noise Gate 1 500-series module High-pass and low-pass key filters Infrared linking between modules

Channel count is the first filter for most buyers. A project studio that gates a kick and a snare needs two good channels, a live rack that handles a full drum kit needs four to eight, and a 500-series owner adds gates one slot at a time. The sections below take the units in order from the long-running dual gate to the modular single channel.

Audio gates for mixers, product by product

Each unit below earned its place from its maker’s own printed specifications, opened and checked for this guide. The order runs from dedicated gates to combined dynamics units and the modular option, and each entry notes the channels, the control ranges and the work the unit fits best.

Drawmer DS201 Dual Noise Gate

The DS201 is the reference dual gate: two channels in a 1U case, each with variable high-pass and low-pass filters in the key path, a full set of envelope controls and a key listen switch. It links for stereo work, switches between gate and duck modes, and has been the default insert on drum channels for decades.

Drawmer prints a threshold range from -50dB to infinity, attack from 10 microseconds to 1 second, hold from 2 milliseconds to 2 seconds and decay from 2 milliseconds to 4 seconds, with range adjustable up to 90 dB of reduction. An external key input on a quarter-inch jack lets another signal open the gate, and the balanced XLR connections run at an input impedance of 20k Ohms with a maximum input level of +17dBu.

The printed audio figures stay honest: bandwidth from under 23Hz to 31kHz at -1dB, noise at -95dB and distortion under 0.025 percent. The case measures 482 by 44 by 200 millimeters and weighs 3.4 kilograms, and the unit draws 9 watts. Pick the DS201 when two channels of precise, filter-led gating cover the job, which for most drum subgroups and stage racks they do.

dbx 1074 QuadGate

The 1074 puts four independent gate channels in a single rack space, and dbx arranges them as two stereo-couple pairs that can also run as two mono channels plus one stereo pair. Each channel carries its own key filter, threshold, depth and release controls, so four different drums keep four different setups inside one unit.

The key filter sweeps from 80Hz to 8kHz per channel, the release runs from 0.01 to 3 seconds on an accelerating curve, and a key input on a quarter-inch TRS jack accepts an external trigger per channel. Stereo Couple makes the odd-numbered channel the master for its pair, and dbx adds program-adaptive expansion circuitry with true RMS detection to keep the gate’s response tied to the signal rather than to stray peaks.

Connections are balanced XLR with an operating level switchable between +4dBu and -10dBV per the manual, input impedance above 50 kOhm and a maximum input above +22 dBu. The printed figures list noise under -96 dBu, dynamic range above 115 dB and THD+N of 0.008 percent at +4 dBu. The case measures 1.75 by 19 by 9 inches, weighs 6.9 pounds and draws 30 watts.

Klark Teknik Square ONE Dynamics SQ1D

The SQ1D is the channel-count answer: eight channels of dynamics in a 3U steel chassis, and every channel switches between compressor and gate duty. A rack that needs gates on the drum kit today and compression on a choir tomorrow can cover both from the same three rack spaces without a second unit.

In gate mode each channel offers threshold, attack, hold, release and range controls, and Klark Teknik adds its iTS Intelligent Threshold Shift hysteresis, which moves the trigger point once the gate opens so a signal hovering at the threshold does not make the channel chatter. A sidechain band-pass filter with wide and narrow settings sits on every channel, alongside an external sidechain input on a balanced quarter-inch TRS jack.

Two details suit live work in particular. Channels link flexibly for stereo sources, and a console-style Solo Bus lets the engineer listen to any channel’s sidechain while setting up, cascading between units over XLR. The compressor side runs RMS or Vintage peak sensing with soft or hard knee. Inputs and outputs are balanced on Neutrik XLR connectors, and an auto-ranging universal switch-mode power supply covers touring voltages without a selector switch.

Because each channel chooses its own job, a single SQ1D often replaces two smaller units in a house rack: four channels gating the drum kit while four more compress a set of wireless handhelds, for example, with the sidechain solo bus shared across all eight. That flexibility is the reason the unit takes 3U where a plain quad gate takes one, and for a fixed installation that trades rack space for fewer boxes and one power supply, the trade usually favors the SQ1D.

dbx 1066 Compressor/Limiter/Gate

The 1066 is a two-channel dynamics unit that combines a compressor, a PeakStopPlus limiter and an expander/gate section in each channel, so it suits owners who need gentle gating on channels that also need level control. Its gate section works as a ratio-based expander as well as a gate, which softens the on-off edge a gate can produce on speech.

dbx prints the expander/gate threshold from off to +15dBu, the ratio from 1:1 to 30:1, an attack under 100 microseconds and a program-dependent release. The sidechain gets two switches that matter in practice: SC Ext routes an external sidechain signal to the detector, and SC Mon routes the sidechain to the output so the engineer can hear exactly what will trigger the unit while an EQ shapes that trigger signal.

The compressor side offers threshold from -40dBu to +20dBu, ratio to infinity, OverEasy or hard knee and auto or manual attack and release, while the limiter threshold runs from +4dBu to +24dBu. Printed figures include noise under -95 dBu, dynamic range above 118 dB and THD+N of 0.008 percent at +4 dBu. The unit measures 1.75 by 19 by 9 inches, weighs 5.1 pounds, draws 20 watts and links its channels for stereo with the first channel as master.

Drawmer MX40 Punch Gate

The MX40 takes the opposite path from the deep-control units: four gate channels in 1U with only three rotary controls per channel. Frequency Trigger sets the band the gate listens to, Threshold sets the level where it opens, and Release sets how long it takes to close, which makes the MX40 quick to set during a soundcheck with the band waiting.

The trigger frequency filter sweeps from 50Hz to 8kHz across a one-octave band, the threshold runs from -60dB to +20dB and the release from 10 milliseconds to 4 seconds, with built-in envelope hold logic that varies with the release setting to hold off chatter. A range button chooses between -20dB and -90dB of reduction when the gate is closed, and the traffic light LED display shows the gate state at a glance.

Peak Punch is the MX40’s signature: Drawmer’s circuit adds a very short burst of dynamic expansion to the leading edge of a percussive signal as the gate opens, with a near-zero attack time, so a gated kick or tom keeps its hit. A shared external key input can trigger any channel, Channel One can trigger all four, and Slave Link pairs channels for stereo. The technical sheet lists 20k Ohm balanced inputs, a maximum input of +21dBu, bandwidth under 10Hz to 22kHz and a 482 by 44 by 175 millimeter case.

Drawmer DS101 500-Series Noise Gate

The DS101 carries a single channel of the DS201 into a 500-series slot, for owners who already run a modular rack and want to add gates one channel at a time. It keeps the two-filter key path and the full envelope set of the rack unit, and it needs a 500-series frame to supply power and connections, which the maker states plainly.

The printed control ranges mirror the DS201 closely: threshold from infinity down to -62dB, attack from 10 microseconds to 1 second, hold from 2 milliseconds to 2 seconds, decay from 2 milliseconds to 4 seconds and range from -80 to 0 dB. The key filters sweep the low control from 22Hz to 3kHz and the high control from 25Hz to 30kHz, and a hysteresis circuit stabilizes the trigger point to hold off chatter around the threshold.

Linking is the clever part. Modules sitting side by side pass an infrared trigger pulse from one to the next, so up to ten units can follow one trigger while each keeps its own envelope settings. A key listen facility, an external key input and a switch between gating and ducking round out the panel, and a three-color traffic light meter shows the gate state. For a studio that gates the same two or three channels every session, a pair of DS101 modules takes less space than any rack unit here.

Matching a gate to the job

The right choice depends less on brand than on the material running through the mixer. Percussion rewards fast attacks and tuned key filters, speech rewards a gentle ratio and a partial range, and a touring rack rewards channel count per rack space above almost everything else.

Drum kits and percussion

Drums are the gate’s home ground, because each microphone hears the full kit while only one drum should open its channel. Key filters matter most here: tune the detector to the drum’s own band and the hi-hat spill that fools a plain threshold gate stops opening the snare channel at the wrong moments.

Four channels cover kick, snare and two toms, which makes the dbx 1074 and the Drawmer MX40 the natural kit units, while the DS201 handles a kick and snare pair with the deepest filter control of the group. The MX40’s Peak Punch adds leading-edge weight to dull toms, and the 1074’s accelerating release keeps long tom decays from ending with a visible cut.

Vocals, speech and broadcast

Speech punishes a hard gate, because a channel that slams shut between words sounds broken on air. The fix is a partial range or an expansion ratio, so the channel drops by a set amount instead of muting, and background noise falls back without ever disappearing in a way the ear notices between sentences.

That is where the dbx 1066 earns its place, since its expander/gate ratio runs from a gentle 1:1 to 30:1 and its release follows the program material. Ducking covers the other broadcast job, dropping music under a voice, and both Drawmer rack units plus the DS101 offer a duck mode. For a row of podium microphones, the SQ1D’s eight channels and anti-chatter hysteresis keep the setup in one chassis.

Channel counts and rack space

Count the channels that truly need gates before choosing a format, because gates multiply fast on a live input list. Two channels suit a project studio, four cover a standard kit, and eight match a festival stage where the same rack serves band after band with no time to re-patch between sets.

The SQ1D gates eight channels in 3U and doubles as eight compressors, the 1074 and MX40 each gate four in 1U, and the DS201 and 1066 gate two in 1U with deeper control per channel. The DS101 breaks the pattern entirely: one channel per 500-series slot, added as the rack grows, with infrared linking that keeps a row of modules acting as one system.

Power and patching deserve a thought as well. Every rack unit here runs on mains power with standard balanced connections, and the printed draws run from 9 watts for the DS201 to 30 watts for the 1074, so a shared rack supply handles several units without strain. The DS101 draws its power from the 500-series frame instead, which keeps the cabling inside the rack and the front panel within arm’s reach of the other modules.

For most mixer owners the short list writes itself: the Drawmer DS201 for two channels of filter-led precision, the dbx 1074 or MX40 for a full drum kit in one rack space, the SQ1D when eight channels must gate or compress, the dbx 1066 for gentle expansion on speech, and the DS101 when a 500-series rack grows one gate at a time.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.