Updated Nov 17, 2026· 16 min read

Key takeaways

  • Find filters that fit a WaterFurnace geothermal system, with the right size, depth, and MERV rating for steady airflow and cleaner indoor air in your home.

A WaterFurnace geothermal system needs a filter that matches its slot size, depth, and airflow needs, so the best filters for water furnace owners start with the size printed on the old filter and the guidance in the unit manual, then choose a MERV rating the blower can handle without strain in every season.

Quick verdict

If the slot takes a 1-inch filter and the manual allows a high rating, a MERV 13 pleated filter in the exact nominal size is a strong starting point, while a MERV 11 filter is a calmer choice for older blowers, pets, and homes where airflow has been a concern in the past.

Product Type Best for Key spec Main limit
Filtrete 20x20x1 MPR 2200 MERV 13 Pleated 1-inch High capture in a 20×20 slot MERV 13, MPR 2200, 2-pack High rating needs a blower that can handle it
Filterbuy 16x25x1 MERV 13 Pleated 1-inch A 16×25 slot with pets and dust MERV 13, 6-pack Actual size is smaller than nominal size
BNX TruFilter 20x20x1 MERV 13 Pleated 1-inch A 20×20 slot with fine particle capture MERV 13, 6-pack High rating needs a blower that can handle it
Filtrete 16x25x1 MPR 1900 MERV 13 Pleated 1-inch A 16×25 slot with fine particle capture MERV 13, MPR 1900, 2-pack Only two filters in the pack
Filterbuy 20x20x5 MERV 11 Pleated deep media Deep media cabinets and longer service MERV 11, 3-pack, 4.38-inch depth Fits only a deep media cabinet
Simply 20x20x1 MERV 11 Pleated 1-inch A 20×20 slot with a mid-level rating MERV 11, MPR 1000, 6-pack Lower capture than the MERV 13 picks

How we selected

Selection started from published specifications and product pages that could be opened and read, with maker pages first and listing pages next, and every size, rating, pack count, and material in this guide comes from one of those pages rather than from memory or from a search snippet.

Each pick had to state a MERV rating, a nominal size, and an actual size on the page that was opened. Products were left out when a page could not be opened, when a rating was in conflict between listings, or when a rate limit stopped the page from loading. No product here is presented as fitting every WaterFurnace model. The list keeps a spread of ratings, with MERV 13 picks where the manual allows it and MERV 11 picks for airflow and deep media cabinets.

Best filters for WaterFurnace geothermal systems

The six filters below are grouped by the slot they fit and the rating they carry, so a reader can start with the nominal size on the old filter, then choose between MERV 13 and MERV 11, and then choose between a 1-inch pleated filter and a deep media filter for a cabinet built for that depth.

Filtrete 20x20x1 MPR 2200 MERV 13 air filter, 2-pack

This Filtrete filter is the high capture pick for a 20x20x1 slot, with a MERV 13 rating and an MPR 2200 rating from 3M, and it is aimed at a home where the manual allows a high rating and where fine particles are the main concern, for homes that want strong capture without a deep media cabinet.

The maker lists this as a 3-month pleated 1-inch electrostatic air cleaning filter, with an actual size of 19.719 by 19.719 by 0.78 inches, a pack of 2 filters, polypropylene material, pleated construction, and an item weight of 1.67 pounds. The maker lists capture of up to 69 percent of small particles and 78 percent of airborne virus particles, given here as the maker lists them. The maker directs the user to change the furnace filter at least every 90 days. It fits a home with a 20x20x1 slot and a blower that can handle MERV 13, but the 2-pack covers fewer changes than a 6-pack, and the high rating can add resistance where airflow is already weak.

  • Pros: MERV 13 and MPR 2200 ratings from the maker, pleated electrostatic media, and a clear 90-day change direction.
  • Cons: Only two filters in the pack, and a high rating that is not right for every blower.

Buy if the slot is 20x20x1, the manual allows MERV 13, and fine particle capture is the aim. Skip if the manual calls for a lower rating or airflow has been weak.

Filterbuy 16x25x1 MERV 13 air filter, 6-pack

This Filterbuy filter is the high capture pick for a 16x25x1 slot, with a MERV 13 rating, a 6-pack, and an actual size that is clearly smaller than the nominal size, so it suits a home that wants a full set of spares on hand, for homes that want strong capture with spares ready.

The page lists the model as AFB16x25x1M13pk6, the actual size as 15.5 by 24.5 by 0.75 inches, and the item weight as 3.1 pounds. The material type is listed as aluminum, plastic, and polypropylene, and the compatible devices are listed as air cleaner, air conditioner, furnace, HVAC system, and heat pump. It fits a home with a 16x25x1 slot and a blower that can handle MERV 13, but the actual size is a half inch smaller than the nominal size on each long side, which is normal for a slide-in filter and still needs a check against the old filter. The opened page did not state a pleat count or a change interval for this listing, so this guide does not give one for it.

  • Pros: MERV 13 rating, a 6-pack for several changes, and a stated model number for reordering.
  • Cons: Actual size is smaller than nominal size, and a high rating that is not right for every blower.

Buy if the slot is 16x25x1, the manual allows MERV 13, and a 6-pack is wanted. Skip if the manual calls for a lower rating or the slot needs a different size.

BNX TruFilter 20x20x1 MERV 13 air filter, 6-pack

This BNX filter is a second high capture pick for a 20x20x1 slot, with a MERV 13 rating and a 6-pack, and it suits a home that wants the same size and rating as the first pick with a different maker and a larger pack, for homes that want a larger pack from a different maker.

The page lists the manufacturer as BNX Converting LLC, the brand as BNX, the model as BN-M13S-20x20x1-6PP, the product dimensions as 19.68 by 19.68 by 0.75 inches, and the item weight as 2.5 pounds. The title states that the filter is made in the USA. It fits a home with a 20x20x1 slot and a blower that can handle MERV 13, but the high rating can add resistance where airflow is already weak, and the opened page did not state a change interval or a pleat count for this listing.

  • Pros: MERV 13 rating, a 6-pack for several changes, and electrostatic pleated media.
  • Cons: A high rating that is not right for every blower, and no change interval stated on the opened page.

Buy if the slot is 20x20x1, the manual allows MERV 13, and a 6-pack is wanted. Skip if the manual calls for a lower rating or airflow has been weak.

Filtrete 16x25x1 MPR 1900 MERV 13 air filter, 2-pack

This Filtrete filter is the high capture pick for a 16x25x1 slot from 3M, with a MERV 13 rating and an MPR 1900 rating, and it suits a home that wants the same rating as the Filterbuy 16x25x1 pick with a different maker and a smaller pack, for homes that want a 3M filter in that size.

The page lists the manufacturer as 3M, the part number as UT01-2PK-6E, the size as 16x25x1, the MERV rating as 13, and the included components as 2 filters. The title states an actual size of 15.719 by 24.72 by 0.78 inches, and the page lists the item weight as 1.19 pounds, the material as electrostatic material, and the color as white. The maker describes this filter as having the highest airflow among MERV 13 filters, and the maker directs the user to change the furnace filter at least every 90 days. It fits a home with a 16x25x1 slot and a blower that can handle MERV 13, but the 2-pack covers fewer changes than a 6-pack.

  • Pros: MERV 13 and MPR 1900 ratings from the maker, a clear 90-day change direction, and a stated part number for reordering.
  • Cons: Only two filters in the pack, and a high rating that is not right for every blower.

Buy if the slot is 16x25x1, the manual allows MERV 13, and a 2-pack is wanted. Skip if the manual calls for a lower rating or a larger pack is wanted.

Filterbuy 20x20x5 MERV 11 air filter, 3-pack

This Filterbuy filter is the deep media pick in this guide, with a MERV 11 rating and a depth of 4.38 inches in actual size, and it is aimed at a home with a media cabinet built for a deep filter rather than a 1-inch rack, for homes with a media cabinet built for deep filters.

The page lists the model as HRF20x20x5M11pk3, the actual size as 19.63 by 19.88 by 4.38 inches, and the number of units per package as 3. The maker describes the media as MERV 11 synthetic media, comparable with Micro Allergen Defense MPR 1200 and FPR 7, and the maker lists capture of 95 percent of dust particles. The maker lists 8 pleats per foot, a frame that can endure temperatures up to 200 degrees Fahrenheit, and a direction to replace every 90 days for best results. The page lists compatible models that include Honeywell F100 and F150 units with the part number FC100A1011. It fits only a deep media cabinet, so the depth must be measured before ordering.

  • Pros: MERV 11 rating for a deep media cabinet, 8 pleats per foot, and a clear 90-day change direction.
  • Cons: Fits only a deep media cabinet, and a lower rating than the MERV 13 picks.

Buy if the cabinet takes a 20x20x5 nominal filter and the manual allows MERV 11. Skip if the slot is only 1 inch deep or the cabinet size is different.

Simply 20x20x1 MERV 11 air filter, 6-pack

This Simply filter is the mid-level pick for a 20x20x1 slot, with a MERV 11 rating and an MPR 1000 rating, and it suits a home that wants a calmer rating than MERV 13 with a full 6-pack on hand, for homes that want a calmer rating with spares ready to use.

The page lists the brand as Simply, the manufacturer as MervFilters, the model as MERV 11, 20x20x1, 6 Pack, the MERV rating as 11.00, and the number of items as 6. The title states an actual size of 19.75 by 19.75 by 0.75 inches, and the page lists the item weight as 3 pounds, the material type as cardboard and paper, and the construction as 24-point beverage board, hot-rolled steel wire mesh, and pleated. The maker lists a comparable rating of MPR 1000 to 1200 and FPR 7, a particle size of 1.0 to 3.0 microns, and a performance span of up to 3 months. The page lists compatible devices as air conditioner, furnace, and heat pump. Its capture level is lower than the MERV 13 picks, and the frame is cardboard and paper rather than a heavier board.

  • Pros: MERV 11 rating for easier airflow, a 6-pack for several changes, and a stated particle size range from the maker.
  • Cons: Lower capture than the MERV 13 picks, and a cardboard and paper frame.

Buy if the slot is 20x20x1, the manual allows MERV 11, and a mid-level rating is wanted. Skip if the manual calls for MERV 13 or a deep media filter is required.

Buying guide: best filters for WaterFurnace units

A good choice starts with the unit in the home rather than with a rating on a box, so read the old filter, read the manual, and check the depth of the rack before ordering, because a filter that is the wrong size will not do its job even if the rating looks right.

Measure the size and depth before ordering in the best filters for water furnace

Read the nominal size printed on the edge of the old filter, then measure the old filter itself and the slot it came from, because the actual size of a pleated filter is smaller than the nominal size and the two numbers are easy to mix up, so check the depth of the rack before you order.

Every pick in this guide shows that gap. The Filtrete 20x20x1 MPR 2200 filter has an actual size of 19.719 by 19.719 by 0.78 inches, the BNX 20x20x1 filter has an actual size of 19.68 by 19.68 by 0.75 inches, and the Simply 20x20x1 filter has an actual size of 19.75 by 19.75 by 0.75 inches. A filter that is too small leaves a gap where air can pass around it, and a filter that is too large will bend or fail to seat. Depth matters too: a 1-inch filter belongs in a 1-inch rack, and a deep media filter belongs only in a cabinet built for that depth.

Choose between MERV 11 and MERV 13 for a geothermal unit in the best filters for water furnace

MERV 11 and MERV 13 are both in the range the brand describes in its AlpinePure literature, so the choice is about the blower, the ductwork, and the home, not about chasing the highest number on the shelf, and the right rating keeps airflow steady over time.

The literature describes MERV as a rating of the ability of a filter to trap particles from 0.3 to 10.0 microns. A MERV 13 filter is aimed at finer particle capture, while a MERV 11 filter is aimed at a mid-level capture with less resistance. In a home with an older blower or weak airflow, MERV 11 is the calmer choice. If the manual names a maximum rating, follow it, and if the manual is silent, a heating and cooling professional can advise on the rating for that model.

Match the filter to the cabinet, not just the size

A home may have a simple 1-inch rack, a 2-inch rack, a 4-inch media cabinet, or an AlpinePure cleaner, and each of those takes a different filter, so the cabinet type should be checked as well as the length and width, and the cabinet type decides which depth will fit.

The AlpinePure literature describes MERV 11 filters in 2-inch and 4-inch sizes and MERV 13 filters in a 2-inch size. The deep media pick in this guide, the Filterbuy 20x20x5 MERV 11 filter, has an actual depth of 4.38 inches and is listed for Honeywell media cabinets, so it belongs only where a deep cabinet is present. A 1-inch pleated filter should never be forced into a deep cabinet with a gap around it, and a deep filter should never be squeezed into a 1-inch rack.

Change the filter on a schedule that fits the home

A filter that stays in place too long loads up with dust, and a loaded filter can cut airflow and let dust reach the coil, so a regular change date matters more than the brand on the frame, and a regular change date keeps airflow steady through the season.

Several makers in this guide give the same direction. The Filtrete 20x20x1 MPR 2200 filter and the Filtrete 16x25x1 MPR 1900 filter are both described as 3-month filters, and the makers direct the user to change the furnace filter at least every 90 days. The Filterbuy 20x20x5 MERV 11 filter carries a direction to replace every 90 days for best results. Write the change date on the frame, set a reminder for the next change, and look at the old filter when it comes out.

Watch airflow and dust after a change

After a new filter goes in, the home itself gives the best feedback, so listen for a change in fan sound, feel the airflow at a vent, and look at how dust settles in the rooms over the next few weeks, and a quick check after each change catches problems early.

A filter that is too restrictive for the blower can show up as weaker airflow, longer run times, or a fan that sounds strained, and a filter that is too small for the slot can show up as dust around the rack or a filter that moves in its frame. If airflow drops sharply after a move to a higher rating, the right step is to go back to the rating the manual allows and to ask a heating and cooling professional about the ductwork and the blower for that model.

FAQ

These questions cover the points that come up most often when a geothermal owner orders a filter for the first time, and the answers point back to the size on the old filter, the manual for the model, and the rating the blower can handle. Read the size first, then the manual, then the rating.

What size filter does a geothermal system take?

There is no single size for every geothermal system, because more than one cabinet and rack is in use, so the size must be read from the old filter and the manual for the model in the home rather than guessed from the brand name, and the depth of the slot matters as much as the length.

The picks in this guide cover 20x20x1, 16x25x1, and 20x20x5 nominal sizes, and each one lists an actual size that is smaller than the nominal size.

Can I use a MERV 13 filter in a geothermal system?

A MERV 13 filter can be a good fit when the manual allows that rating and the blower can handle it, and the brand itself describes MERV 13 filters in a 2-inch depth in its AlpinePure literature, so the rating is within the range the brand discusses, before ordering a higher rating.

The MERV 13 picks in this guide are the Filtrete 20x20x1 MPR 2200 filter, the Filterbuy 16x25x1 filter, the BNX TruFilter 20x20x1 filter, and the Filtrete 16x25x1 MPR 1900 filter. If the manual names a maximum rating, follow it. If airflow has been weak, or if the system has struggled with a high rating before, a MERV 11 filter is the calmer choice.

How often should I change a filter in a geothermal system?

Follow the direction on the filter box and in the manual, and use the maker directions in this guide as a starting point, because several makers give the same interval for their 1-inch and deep media filters, and the same interval fits most 1-inch and deep media filters.

The Filtrete 20x20x1 MPR 2200 filter and the Filtrete 16x25x1 MPR 1900 filter are both described as 3-month filters, and the makers direct the user to change the furnace filter at least every 90 days. The Filterbuy 20x20x5 MERV 11 filter carries a direction to replace every 90 days for best results, and the Simply 20x20x1 MERV 11 filter is described by the maker as giving performance for up to 3 months. Write the change date on the frame and look at the old filter when it comes out.

Does a geothermal system need a special brand of filter?

No special brand is required for a standard 1-inch rack or a deep media cabinet, and the filter that fits is the one with the right nominal size, the right depth, and a rating the manual allows, whatever brand makes it, and the size, depth, and rating matter more than the brand.

The brand does sell its own AlpinePure filters, and the literature describes a HEPA filter, an electronic air cleaner, an electrostatic filter, MERV 11 filters, MERV 13 filters, and a carbon filter for the AlpinePure 411 housing. Those are options for a home with an AlpinePure unit. For a standard rack, the picks in this guide from Filtrete, Filterbuy, BNX, and Simply all state a nominal size, an actual size, and a MERV rating on the page that was opened, and any of them can fit when the size and rating match the unit.

What is the difference between a 1-inch filter and a deep media filter?

A 1-inch filter is a thin pleated filter that slides into a 1-inch rack, while a deep media filter is a thick pleated filter that sits in a media cabinet built for that depth, and the two cannot be swapped without a gap or a forced fit, and the cabinet depth decides which type will fit.

The 1-inch picks in this guide have an actual depth of 0.75 inches or 0.78 inches, and they are made to slide into a 1-inch slot. The deep media pick, the Filterbuy 20x20x5 MERV 11 filter, has an actual size of 19.63 by 19.88 by 4.38 inches, and it is made for a media cabinet that takes a 20x20x5 nominal filter. The brand describes MERV 11 filters in a 4-inch depth in its AlpinePure literature, which shows that deep media is a normal option for some of its homes.

Conclusion

Start with the size and depth printed on the old filter, match the MERV rating to the manual, and choose a 1-inch pleated filter for a standard rack or a deep media filter for a media cabinet, so the system keeps steady airflow with a filter that fits well and is changed on time, and check the fit again at the next change.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.