Key takeaways
- Six outboard effects units that patch into an analogue mixer's aux sends, compared on key maker specs: operating level, inputs, engines, presets and format.
An analogue mixer with no built-in effects is not a dead end; it is an invitation to choose your own. This guide builds an external fx setup for analogue mixers from six outboard units whose maker pages print the figures that matter at the patch bay: operating level, input connectors, engine count and preset memory.
Quick verdict
For a rack beside the desk, take the Behringer FX2000: balanced XLR and jack connections with a switchable -10 dBV or +4 dBu operating level, so it matches any aux send ever made. For two effects from one box, the Lexicon MX200 and the Eventide H90 both run two independent engines; the MX200 does it in 1U of rack, the H90 on the floor.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Behringer Virtualizer 3D FX2000 | 1U rack processor | Level matching any desk | Operating level -10 dBV or +4 dBu, selectable | One stereo effect path at a time |
| Lexicon MX200 | 1U rack, dual processor | Two aux effects in one unit | Two 24-bit processors, four routing modes | Jack connections only, no XLR |
| Alesis NanoVerb 2 | Desktop processor | The simplest first outboard unit | 16 presets with 16 variations each, 256 effects | Unbalanced inputs and outputs |
| Eventide H90 Harmonizer | Pedal, dual path | Two stereo effects plus inserts | Line level input up to +14 dBu | Needs its 12V 1A supply |
| Strymon BigSky MX | Pedal, reverb only | A dedicated reverb send | Two reverbs at once, 300 preset locations | Maximum input +10 dBu; reverb only |
| Zoom MS-70CDR+ | Compact pedal | Smallest budget send effect | 149 effects, up to 6 at once | Rated input level -20 dBu; run the send low |
How we selected
The reading behind this guide is the aux send itself. An external unit earns its place beside a mixer when a post-fader aux can feed it at a level it accepts, and its output can return wet to an aux return or a spare channel. Every unit below was read on a maker page, maker document or full listing, and only printed figures are used.
Three printed figures decide fitness. Operating level and maximum input level decide whether the unit takes a +4 dBu send without clipping or a -10 dBV send without noise. Engine count decides whether one box covers one aux send or two. Connector type decides the cabling: balanced XLR or TRS for long runs to a rack, unbalanced jacks for a unit sitting on or beside the desk.
Format follows from those figures. Two of the six are 1U rack processors built for exactly this job. One is a desktop box whose maker manual documents the aux send hookup step by step. Three are pedals whose makers publish line level input specifications, which is what qualifies a pedal for send duty rather than guitar duty alone.
External fx setup for analogue mixers: the six units in detail
Six units follow, in the order a buyer usually meets them: the two rack processors first, then the desktop box, then the three pedals with printed line level specifications. Each section states who the unit suits, the maker figures behind it, and the limit to plan around. Prices are not stated anywhere in this guide.
Behringer Virtualizer 3D FX2000
The FX2000 is the rack default for this job because of one specification the others do not offer: a nominal operating level selectable between -10 dBV and +4 dBu. Analogue desks send at both levels depending on their class, and this 1U processor matches either at the flick of its design, with servo-balanced XLR and 1/4 inch TRS inputs and outputs.
The maker’s product document lists 71 algorithms built on its RSM (Real Sound Modeling) processing, including 12 reverb programs and 11 effect combinations with selectable serial or parallel configuration. Up to 7 parameters plus a 2-band EQ are adjustable per effect. Memory holds 100 factory presets and 100 user locations, and MIDI implementation is extensive, with 5-pin DIN in, out and thru sockets for program changes from a controller.
The spec table prints a bandwidth of 20 Hz to 20 kHz, a signal-to-noise ratio of 91 dB, maximum input and output levels of +15 dBu at the +4 dBu nominal setting, and 24-bit converters running at a 46.875 kHz sampling rate. The unit is light for a rack at about 4.18 pounds and draws 15 watts. Its limit is architecture: one stereo effect path at a time, so a second independent aux effect means a second unit.
Pros: switchable operating level fits any desk; balanced XLR and jack connections; large preset memory; LED level meters for setting send levels. Cons: single effect path; the 91 dB signal-to-noise figure is the lowest of the rack pair here. Buy if the desk’s aux level is fixed and unknown. Skip if two different effects must run at once from one box.
Lexicon MX200
The MX200 answers the two-effects problem inside one rack space: two independent 24-bit processors, each with its own control area and three parameter knobs, running two effects at once. In Dual Mono routing, the two processors behave as two separate mono-to-stereo units, which is precisely two aux sends served by a single 1U box.
Lexicon lists 32 reverbs and effects: 16 reverbs including hall, plate, room, chamber, gated, reverse and spring; six delays including tape and reverse; dbx dynamics in a compressor and a de-esser; and chorus, flanger, phaser, tremolo, rotary, vibrato, pitch shift and detune. Four routing modes cover Dual Mono, Cascade, Dual Stereo (Parallel) and Mono Split, and memory holds 99 factory programs plus 99 user programs.
Connections are two 1/4 inch TRS inputs and outputs, balanced or unbalanced, with an input level of +4 dBu nominal and +20 dBu maximum, a frequency response of 20 Hz to 20 kHz and a dynamic range above 107 dB. S/PDIF digital in and out, MIDI and a USB port that lets the unit work as a hardware plug-in round out the panel. The honest limits: no XLR sockets, and power comes from a 9V AC wall adapter rather than an internal supply.
Pros: two independent effects in 1U; +20 dBu maximum input swallows hot sends; named Lexicon reverb set; tap tempo per processor. Cons: jack-only connections; external power adapter. Buy if two aux sends need two different effects and rack space is tight. Skip if the rack standard is XLR throughout.
Alesis NanoVerb 2
The NanoVerb 2 is the beginner’s outboard unit, and its maker’s quickstart guide is the only document in this group that teaches the setup itself: it names aux sends on a mixer as the input source, aux returns as the destination, and prints a six-step procedure for setting mixer aux send and return levels against the unit’s input LED.
The box offers 16 factory presets, each with 16 variations, for 256 effects in total: three halls, two springs, two plates, a tape delay, a delay, chorus, flanger, tremolo, rotary, and combined reverb-plus-delay, reverb-plus-flanger and reverb-plus-chorus programs. Front panel controls are input, output and mix knobs plus the two selector knobs, with a signal LED that lights when the input runs too hot.
Connections are 1/4 inch unbalanced inputs and outputs, and the manual’s mono, mono-in-stereo-out and stereo hookup diagrams map directly onto one aux send with a mono or stereo return. A rear jack takes a momentary footswitch for bypass. The limits are the unbalanced connections and the fixed preset architecture: parameters beyond the variation knob are not exposed, and there is no user memory to store a setting.
Pros: maker documentation teaches the aux setup directly; tiny learning curve; stereo return from a mono send; footswitch bypass. Cons: unbalanced connections only; no user presets; limited parameter editing. Buy as a first external effect for a small desk. Skip if the mixer lives in a rack across the room from the unit.
Eventide H90 Harmonizer
The H90 is the pedal that behaves like a small rack. It runs two algorithms at once per program from a library of 74, and its Dual Mode processes two independent stereo signals at the same time, which maps onto two aux sends: a reverb on one path, a delay or modulation on the other, each recalled as part of one program.
Eventide publishes the line level figures that qualify it for send duty: four 1/4 inch TS inputs and four outputs, instrument or line level operation with full gain controls, a maximum input level of +14 dBu at line level, input impedance above 80k ohms at line level and an output impedance of 220 ohms. Two mono inserts, or one stereo insert, can be positioned anywhere in the signal chain, so another outboard box can sit inside the H90’s routing.
The library covers the full H9 Max set plus 22 newer algorithms, including the SP2016 Reverb and four vocal algorithms, VocalTune, VocalShift, VocalShiftMIDI and Quadravox+, that suit a lead vocal send. Control runs through the Eventide Control app over Bluetooth or USB-C, and MIDI in and out handle program changes. Power is a 12V DC 1A center-positive supply, included in the box; standard pedalboard taps will not run it.
Pros: two independent stereo paths; published line level headroom; inserts for further outboard gear; deep library with vocal tools. Cons: the dedicated 12V 1A supply is one more brick to manage; TS connections are unbalanced. Buy if one floor unit must cover two sends and studio-style editing appeals. Skip if the rig must run from a standard 9V pedal supply.
Strymon BigSky MX
The BigSky MX is the specialist: a reverb-only unit for the buyer whose analogue desk needs one excellent reverb send above all else. It runs two of its 12 reverb machines at once, routed in series, parallel or split, with each engine panned individually, and holds 300 preset locations for scenes and songs.
Strymon publishes selectable input level for instrument and line level signals in the global settings, a maximum input level of +10 dBu, stereo inputs and outputs on discrete Class A JFET preamps, an input impedance of 1 Meg Ohm and an output impedance of 100 ohms. Conversion is 24-bit at 96 kHz with a signal-to-noise figure of 116 dB typical, and an analog dry path keeps the dry signal unconverted when the unit is used as an insert.
The machine list runs Impulse, Room, Hall, Plate, Spring, Chamber, Cloud, Shimmer, Bloom, Chorale, Magneto and Nonlinear. The Impulse machine loads stereo impulse responses up to 10 seconds long, with 22 preloaded, so a captured plate or a real room can become the house reverb. Plan around two figures: the +10 dBu input ceiling asks for a measured aux send level, and the 9V DC supply at 500 mA minimum is sold separately.
Pros: two reverbs at once with per-engine pan; impulse response loading for real spaces; high conversion spec; 300 presets. Cons: reverb only, no delays or dynamics; lowest input ceiling of the group apart from the Zoom; power supply not included. Buy if reverb quality is the whole point of the send. Skip if the same box must also cover delay.
Zoom MS-70CDR+
The Zoom is the smallest and simplest way to give an analogue desk a stereo send effect: a single stompbox holding 149 effects, with up to 6 running at once in a chain, 80 factory presets and 100 user patch memories. For a rehearsal room desk or a small live rig, that chain can be the whole effects department.
The maker lists 33 reverbs, 29 delays with times up to 4 seconds, 43 chorus and modulation effects and 44 dynamics and filter effects, 58 of them stereo. Stereo inputs accept line level devices and the dual outputs are line level, with USB MIDI for remote patch changes and an iOS app for patch management. Sampling runs at 44.1 kHz with 24-bit conversion, and the input signal-to-noise figure is a strong 122 dB.
The limit is printed in Zoom’s own specification: the rated input level is -20 dBu, an instrument-level figure, and the maximum output level is +7.2 dBu. A mixer aux send must therefore be run well below its usual level to keep this pedal clean, which costs some noise margin on the return. It runs on a 9V DC adapter, two AA batteries or USB bus power, a flexibility the rack units do not offer.
Pros: huge effect count in the smallest box here; chains up to 6 effects; battery or USB power for odd locations; USB MIDI patch recall. Cons: -20 dBu rated input level demands a gentle send; no balanced connections; adapter not included. Buy for a compact or portable desk where levels can be managed. Skip for a fixed install with hot +4 dBu sends.
Buying guide
Four decisions build the setup: matching the unit’s level figures to the desk’s aux output, deciding how many independent effects must run at once, choosing the format that fits the room, and setting the blend at the desk rather than in the unit. Each is taken in turn below.
Match the operating level first in an external fx setup for analogue mixers
Level mismatch is the failure mode of outboard effects: too hot and the unit clips, too low and the return hisses. Nominal operating level tells you the unit’s home territory, +4 dBu for the MX200 and a switchable -10 dBV or +4 dBu for the FX2000. Maximum input level is the ceiling: +20 dBu on the MX200, +10 dBu on the BigSky MX.
Pedals need the most care. The H90 publishes a line level mode with a +14 dBu ceiling, the BigSky MX selects line level in its settings, and the Zoom rates its input at -20 dBu, which means turning the aux send down and accepting a quieter return. None of this is guesswork: every figure above is printed by the maker, and the right unit is the one whose figures bracket your desk’s aux output.
One effect at a time, or two engines
Count the aux sends you actually use. A single vocal reverb send needs one stereo path, and any unit here covers it. Two sends, typically a reverb and a tempo delay, need either two units or one dual-engine box: the MX200 runs two processors in Dual Mono, and the H90 processes two independent stereo signals in Dual Mode.
Chains are a different tool. The Zoom stacks up to 6 effects in series, and the FX2000 offers 11 preset combinations with serial or parallel configuration, which suits a single send carrying a combined sound. Decide whether your desk time is spent blending two separate effects or shaping one combined effect, and the architecture chooses itself.
Rack, desktop or floor
Rack processors suit a fixed install: the FX2000 and MX200 mount in 1U each, present their controls at the rack, and take MIDI program changes for set lists. The FX2000 adds balanced XLR connections for long cable runs; the MX200’s jacks and wall adapter suit a short patch bay beside the desk instead.
Desktop and floor units suit desks that move. The NanoVerb 2 sits beside a small mixer with its two-knob control scheme in reach, and the pedals travel in the same case as the cables. Remember the power figures when planning: the H90 needs its own 12V 1A supply, the BigSky MX needs a 9V supply at 500 mA that is not in the box, and the Zoom can run on batteries when no spare outlet exists.
Run the unit fully wet, blend at the desk
On an aux send, the desk already controls how much dry signal reaches the mix, so the unit should return effect only. Set the unit’s mix control to fully wet: the NanoVerb 2 manual describes exactly this behavior, with the far right of its mix knob passing only the processed signal, and its level procedure sets the aux return as the blend control.
The exception is insert use, where the whole channel passes through the unit and the mix knob becomes the blend; the BigSky MX’s analog dry path is built for that case. Whichever route you patch, set the unit’s input level by its meter or signal LED first, as the Alesis procedure lays out, then balance the effect from the desk’s return control.
Presets, MIDI and recall
Live work rewards recall. The FX2000 stores 100 user presets under full MIDI control, the MX200 stores 99 user programs, the BigSky MX holds 300 preset locations and the Zoom takes patch changes over USB MIDI. A desk with no memory of its own gains a memory through the outboard unit’s preset list.
Match the recall system to the show. A single house setting needs only a handful of user slots and front panel knobs. A set list with a different reverb per song needs program change control from a foot controller or a playback rig, which the rack units and the H90 accept over standard 5-pin MIDI. The NanoVerb 2, with no user memory, belongs to the set-and-stay world.
FAQ
Five questions cover most first setups: whether pedals can take a mixer send at all, how an aux send differs from an insert, why the unit runs fully wet, whether balanced cables are required, and how many sends a typical rig needs. The answers stay with the maker figures used in this guide.
Can a guitar pedal really work as an external fx setup for analogue mixers?
Yes, when the maker publishes line level figures for it. The H90 specifies line level operation with a +14 dBu maximum input, the BigSky MX offers a selectable line level input, and the Zoom accepts line level devices at its inputs. The check is the same: find the maximum input level in the maker’s specification and keep the aux send under it.
What is the difference between an aux send and an insert?
An aux send takes a copy of the channel signal, and the effect returns to the mix through a return control; several channels can share one effect. An insert routes one channel’s whole signal through the unit and back. Sends suit shared reverbs and delays; inserts suit one channel’s dedicated processing, such as the MX200’s dbx compressor.
Why should the unit be set to 100 percent wet?
Because the desk is already mixing the dry signal from the channels. If the returned signal also carries dry sound, the blend doubles the dry path and the aux return control stops acting as a simple level. Setting the unit fully wet, as the NanoVerb 2 manual describes, keeps one dry path and one wet path, each under its own control.
Do I need balanced cables between the desk and the unit?
Only the FX2000 offers balanced connections on both XLR and jack sockets, and the MX200’s TRS sockets accept balanced or unbalanced plugs. The other four units use unbalanced TS connections. Unbalanced runs are fine across a desk or a short rack distance; for a long run across a stage, the balanced rack units are the printed-spec answer.
How many aux sends does a typical setup need?
One post-fader send per independent effect. Most small analogue rigs run one reverb send, or a reverb and a delay on two sends. A dual-engine unit such as the MX200 or the H90 covers the two-send case in one box; a single-path unit covers one send each. Count your sends before counting effects, and buy engines to match.
Conclusion
Build the setup around the FX2000 if levels are uncertain, the MX200 if two sends need two effects in one rack space, and the H90 or BigSky MX if the rig lives on the floor. Add the NanoVerb 2 for the simplest desk in the building, keep every unit fully wet, and let the desk itself do the blending it was built for.