Key takeaways
- Only two 36 inch gas cooktops with downdrafts are sold. Compare the KitchenAid KCGD506GSS and JennAir JGD3536GS on burners, vent ratings and fuel conversion.
Shoppers looking for 36 inch gas cooktops with downdrafts face a short shelf: only two distinct models are on sale today, one from KitchenAid and one from JennAir, and no third model holds up when its own maker page is read. This guide compares both on burner output, vent ratings, grates and fuel conversion.
Quick verdict
The whole category fits in one short paragraph. The KitchenAid KCGD506GSS pairs five burners with a 300 CFM exhaust rating and full-width cast-iron grates, while the JennAir JGD3536GS answers with sealed brass burners, a melt cap on its low burner and a 297 CFM Motor Class blower in the JX3 system.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| KitchenAid 36 inch 5 Burner Gas Downdraft Cooktop KCGD506GSS | 36 inch gas downdraft | Published vent rating and grate coverage | 300 CFM exhaust rating, 3-speed fan control | Duct-free conversion kit not included |
| JennAir Euro-Style 36 inch JX3 Gas Downdraft Cooktop JGD3536GS | 36 inch gas downdraft | Low heat control and burner build | 5,000 BTU ultra-low burner with melt cap | Full per-burner map not stated on the maker page |
Because the field holds exactly two models, the decision is less about ranking and more about fit. Both are 36 inch, five-burner, gas units with the vent built into the surface and three fan speeds. They part company on how the vent strength is stated, how the burners are built and what the low end of the heat range does.
How we selected
The selection rule for this keyword was strict: a model counts only if it is a 36 inch gas cooktop with the downdraft vent built into the cooking surface, sold as one unit. Models that pair a standard cooktop with a separate pop-up vent, and 36 inch downdraft models that run on electricity, were left out.
That rule leaves two models standing. Roundups elsewhere list longer sets of 36 inch gas cooktops under a downdraft heading, but page by page those extra names turn out to be ordinary gas cooktops with no vent built in, or electric downdraft units wearing a gas label. Neither kind belongs in a gas downdraft comparison.
Finish variants were not counted as separate models. The JennAir line also appears in a black finish under a second model number, but the burner set and vent hardware are the same JX3 platform, so it is treated here as one model with two finishes rather than as a third entry in a two-model field.
Every figure below comes from a maker or listing page for the exact model: burner output in BTU, the vent rating as the maker states it, fan speeds, grate material and conversion notes. Where a page does not state a figure, the article says so instead of filling the gap, because a missing number is itself useful information at this end of the market.
The two makers also publish in different dialects, and the comparison keeps their terms separate on purpose. KitchenAid states an exhaust rating and names its burners by role, Professional and Even-Heat. JennAir states a Motor Class blower figure and names its burners by output position, Ultra-High and Ultra-Low. Merging those vocabularies into one scale would invent a precision the pages do not offer.
The two 36 inch gas cooktops with downdrafts in detail
Two product sections follow, one per model. Each covers who the cooktop suits, the burner and vent figures its maker publishes, the conversion path for liquid propane and duct-free venting, and the limits a buyer should weigh before ordering a unit that has to match an existing 36 inch cutout.
KitchenAid 36 inch 5 Burner Gas Downdraft Cooktop KCGD506GSS
The maker lists this 36 inch cooktop with five burners and a downdraft ventilation system that needs no separate hood, which is the layout that lets a wide cooktop sit in an island or under a cabinet run with no vent hardware above it. The surface is covered by full-width cast-iron grates.
On output, the maker names three burners directly: a 17K BTU Professional Burner, a 15K BTU Professional Burner and a 5K BTU Even-Heat Simmer Burner. Two strong burners at the top of the range and a dedicated simmer burner at the bottom give the published set a wide spread, from a rolling boil down to a low, steady heat for sauces.
The simmer burner carries a melt cap, a small cover that spreads low heat under a small pan, and the maker lists electronic ignition with automatic re-ignition across the surface. Stainless steel knobs control the burners. The maker page states output for three of the five burners; the output of the remaining two burners is not stated on that page.
The vent side is published as a 300 CFM exhaust rating with a 3-speed fan control, the highest vent figure stated by either maker in this pair, and it is stated as an exhaust rating rather than a motor class. For fuel, the maker lists an LP conversion kit, while conversion to duct-free ventilation needs a kit that is not included with the cooktop.
- Pros: 300 CFM exhaust rating published; two high-output burners named; full-width cast-iron grates; melt cap on the simmer burner
- Cons: duct-free conversion kit not included; two burner outputs not stated on the maker page
Buy if you want the stronger published vent figure and a grate layout that lets heavy pots slide across the whole surface. Skip if your venting plan is duct-free from the start, since that conversion kit is an extra purchase on this model.
JennAir Euro-Style 36 inch JX3 Gas Downdraft Cooktop JGD3536GS
The maker lists five sealed burners on this 36 inch Euro-Style model, with ventilation handled by the JX3 Downdraft Ventilation System. Sealed burners keep spills on the surface instead of letting them run under the cooktop, and the burners themselves are brass with a removable base.
The published output figures name the ends of the range: a 17,000 BTU Ultra-High Output Burner at the top and a 5,000 BTU Ultra-Low Output Burner with a Melt Cap at the bottom. That melt cap is the detail cooks reach for when butter or chocolate has to hold at a low, even heat without scorching in a thin pan.
The JX3 vent runs at three speeds, and the maker publishes a 297 CFM Motor Class figure for its blower. Motor Class is JennAir’s own way of stating blower strength, so the number sits close to the KitchenAid exhaust rating without being the same measurement, a point the buying guide below returns to.
The maker lists DuraFinish Protection on the stainless steel models, and lists the cooktop as convertible to duct-free ventilation with an optional kit. The opened maker page states the high and low burner figures but does not publish a full per-burner map for all five burners, so cooks who plan around exact mid-range outputs will find less detail here than the headline numbers suggest.
- Pros: sealed brass burners with removable base; melt cap on the ultra-low burner; DuraFinish Protection on stainless models
- Cons: duct-free conversion needs an optional kit; per-burner output for the middle burners not stated on the maker page
Buy if burner build and low-heat control lead your list, and if a stainless finish with the listed surface protection fits your kitchen. Skip if you want every burner’s output published before you buy, or if the black finish is the one you want, since that is the same platform in a second finish.
Buying guide
With only two models in the category, the buying guide does the heavy lifting: it walks through the points where the pair genuinely differ, the figures each maker chooses to publish, and the installation questions that matter more than brand once a 36 inch cutout and a downward vent path are fixed parts of the plan.
What 36 inch gas cooktops with downdrafts share under the surface
Start with the shared ground, because it is wide. Both models are 36 inch gas cooktops with five burners, a vent built into the surface, three fan speeds and a published path to duct-free venting and to liquid propane. A kitchen planned around either unit starts from the same basic shape.
The vent sits in the cooking surface itself, drawing steam and cooking vapor down through the unit instead of up into a hood. That is what frees the layout: an island bench, a run under windows, or a counter where an overhead hood would block sight lines all stay possible with the vent built into the cooktop.
Shared ground also means shared limits. Neither maker publishes a complete dimension and cutout table on the pages read for this guide, and neither includes the duct-free conversion kit in the box. Those two gaps shape the installation planning for whichever model you pick, so they are covered in their own sections below.
Burner output, and reading figures a maker leaves unstated
Both makers headline the same top figure, 17,000 BTU on the JennAir page and 17K BTU on the KitchenAid page, and both publish a 5,000 BTU low burner with a melt cap. On the headline numbers alone the pair look even, which is why the unstated figures matter as much as the stated ones.
KitchenAid names a second strong burner at 15K BTU, which gives its published set two high-output positions. JennAir’s opened page names only the highest and lowest burners for this model. A cook who runs two large pots at full heat at once can plan around the KitchenAid figures today; on the JennAir, the middle burners are a question to put to the listing page before ordering.
Treat an unstated figure as a prompt, not a verdict. Makers publish different slices of the same kind of data, and a missing per-burner map does not mean weak burners. It does mean the comparison has to be honest about which numbers are on the page and which are not, rather than spreading one model’s figures across both.
Vent ratings are not stated in the same terms
The KitchenAid page states a 300 CFM exhaust rating. The JennAir page states a 297 CFM Motor Class blower figure. The numbers sit three points apart, but they are not the same measurement: an exhaust rating and a motor class figure come from different ways of describing blower strength.
Read them as a band rather than a photo finish. Both makers are describing a three-speed vent in the same strength neighborhood, built into the surface of a five-burner cooktop. The practical difference between the two vents will come from duct length, turns in the duct run and how the vent is installed, not from a three-point gap on paper.
Fan speeds match at three on both models, so control is not the separator either. Low speed suits a simmering pan, the top speed suits a full boil or a searing skillet, and the middle setting covers most weeknight cooking. What differs is only the vocabulary on the page, and keeping each maker’s own term is the honest way to compare them.
Ducted or duct-free: plan the vent path early
A downdraft vent has to send the air somewhere. Ducted venting carries it outside through ductwork under the floor or through the cabinet run. Duct-free venting filters the air and returns it to the room, which suits homes where an outside duct run cannot be built at all.
Both models here can convert to duct-free venting, and on both models that conversion kit is a separate purchase, listed as not included by KitchenAid and as an optional kit by JennAir. Price the kit and confirm its part number for the exact model before the cooktop order is placed, not after the unit is already sitting in the cutout.
The ducted route needs its own planning. The vent housing sits below the cooking surface, so cabinet depth, drawer runs and floor joists all share space with the duct path. Neither maker page read for this guide publishes the full housing dimensions, which makes the install guide for the exact model a required read before cabinetry is ordered.
Liquid propane conversion and ignition
Households off the natural gas grid run cooktops on liquid propane, and a gas cooktop needs a conversion to burn it correctly. KitchenAid lists an LP conversion kit for the KCGD506GSS. JennAir’s listing for this model family covers LP conversion as well, and the conversion work itself belongs to a qualified installer in either case.
Ignition is electronic on the KitchenAid, with automatic re-ignition listed as well: if a burner flame goes out, the system works to relight it. That matters on a downdraft surface, where the vent draw sits close to the flame and a gust through an open window can disturb a low burner at the wrong moment.
Confirm the fuel question before anything else, because it shapes the order. A cooktop that arrives set for natural gas in a propane household waits on parts and an installer visit, while the same check done at ordering time turns conversion into a single planned step in the install.
Grates, knobs and day-to-day cleaning
KitchenAid covers its surface with full-width cast-iron grates, so a heavy stockpot can slide from a strong burner to the simmer burner without being lifted. Cast iron is heavy and holds heat, and full-width coverage means fewer gaps for a small pan to tip into when it is moved mid-recipe.
JennAir takes a different route to the same daily problems: sealed burners keep spills on the surface where they can be wiped up, the brass burners lift off their base for cleaning, and DuraFinish Protection is listed on the stainless models. The two designs answer the same cleaning questions with different hardware, and neither approach needs specialty products to maintain.
Knobs and controls are the third daily touchpoint. KitchenAid lists stainless steel knobs on this model. On either cooktop, the routine is the same: grates off, surface wiped once it has cooled, burner caps and bases back in their exact seats so the flame pattern stays even across the surface.
FAQ
Five questions cover the ground shoppers ask about most in this small category: whether other models exist, what the black JennAir finish means, how the fuel conversion works, whether a hood is still needed, and which figures the makers leave unpublished for these two units.
Are there other 36 inch gas cooktops with downdrafts?
Not that maker and listing pages support. Longer lists in roundups add ordinary gas cooktops with no built-in vent, or electric downdraft models, under a gas downdraft heading. Checked page by page, the 36 inch gas downdraft category sold today is the KitchenAid KCGD506GSS and the JennAir JGD3536GS.
That small field is worth knowing before you shop, because it changes the task. Instead of narrowing a long list, you are choosing between two known platforms, and the effort goes into cutout fit, vent path and fuel setup rather than into hunting for a third or fourth model that pages do not back up.
Is the black JennAir a separate third model?
The JennAir 36 inch JX3 line is sold in a black finish under its own model number, JGD3536GB, alongside the stainless Euro-Style JGD3536GS covered above. The burner set, the JX3 vent system and the published figures are the same platform in both finishes, so this guide counts it as one model with two finishes.
One caution travels with the black finish: the listing page read during research showed that finish on a pre-order status rather than in stock. Availability belongs to the listing page at the moment of ordering, and the article makes no claim about it either way; check the current listing before planning a kitchen around the black unit.
Can either cooktop run on liquid propane?
Yes, with conversion. KitchenAid lists an LP conversion kit for the KCGD506GSS, and the JennAir model family is listed as LP convertible as well. Conversion changes the burner orifices and settings for propane, and it is installer work, not a knob setting, so plan it as part of the installation rather than as an afterthought.
Ask about the kit when you order. On some listings the kit ships with the cooktop and on others it is a separate line item, and the only reliable answer is the one on the page for the exact model number you are buying, read on the day you buy it.
Does a downdraft cooktop still need a hood?
The makers design these units to work without one. KitchenAid states plainly that its downdraft ventilation needs no separate hood, and the JennAir JX3 system is likewise the whole vent plan for the cooktop. The vent in the surface is the appliance; a hood above it is not part of either maker’s setup for these models.
What the built-in vent does need is its own path for the air, ducted outside or converted to duct-free operation with the kit described in the buying guide. Local building rules can still speak to venting in a given home, so the installer who fits the unit is the right check for your address.
Which figures do the makers not publish for these models?
Two gaps stand out. KitchenAid states output for three of its five burners and leaves the other two unstated on the maker page, and JennAir states the highest and lowest burners without a full per-burner map. Neither page read for this guide publishes a complete cutout and dimension table for its model.
Those gaps do not block a decision, but they do set the homework. Pull the install guide for the exact model before cabinetry is ordered, and put any missing burner figure to the listing page in writing. A figure that arrives after the cooktop is a surprise; the same figure asked for before ordering is just planning.
Conclusion
Two models are the whole market here, and both are credible: the KitchenAid KCGD506GSS on its published 300 CFM exhaust rating and full-width grates, the JennAir JGD3536GS on sealed brass burners and low-heat control. Pick by vent path, fuel setup and which published figures matter most in your kitchen.