Key takeaways
- Compare faucets for kitchen with d shaped sinks by stated spout reach and swivel range, so the stream lands mid-basin along the curved front of a D-shaped bowl.
A D-shaped sink pairs a straight back edge with a curved front, so the faucet sits on a narrow rear deck while the basin bulges toward the cook. The right faucets for kitchen with d shaped sinks carry the stream forward into that curve with a measured reach, then swing along it with a wide swivel range.
Quick verdict
Reach and swivel decide this category, and the Kraus Allyn states the longest reach in the group at 9 in, which places its stream deepest into the curved front of a D-shaped basin. The Kraus Oletto is close behind at 8 7/8 in and adds a full 360 degree swivel, so it can follow the curve from one side of the bowl to the other.
The remaining picks trade in the other direction: the Bolden states a slightly shorter reach with a 180 degree swing, while the Delta Essa and the Kraus Sellette lean on full 360 degree swivel and hose travel rather than a long fixed throw. Every reach and swivel figure below comes from the maker page for that model, and where a maker does not publish a reach, the article says the pick rests on swivel instead. None of the five needs a special deck or a nonstandard hole pattern to mount.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Kraus Allyn KPF-4103SFS | Pull-out | Deepest stream placement | 9 in reach, 120 degree swivel | Narrowest swivel in the group |
| Kraus Oletto KPF-2820CH | Pull-down | Reach plus full rotation | 8 7/8 in reach, 360 degree swivel | Single-hole mounting only |
| Kraus Bolden KPF-1610SS | Pull-down | Low outlet over the curve | 8 5/8 in reach, 180 degree swivel | Tallest body in this group |
| Delta Essa 9113-AR-DST | Pull-down | Following the curve by hose | 360 degree swivel, 20 in hose | Maker does not state a spout reach |
| Kraus Sellette KPF-1680SFS-KSD-80SFS | Pull-down with dispenser | Full swivel plus soap dispenser | 360 degree swivel, dispenser included | Dispenser needs its own deck hole |
How we selected
The geometry of a D-shaped sink set the entry rule. A model had to publish either a spout reach or a swivel range on its maker page, because those are the two numbers that decide where the stream lands in a basin that is shallow at the back and deep at the front. Models with neither figure published were left out.
Ranking then followed the shape of the bowl. Stated reach was weighed first, since the mounting hole sits on the straight rear deck and the basin center lies well forward of it. Swivel range came second, because a D-shaped bowl is wider along its curve than a rectangular bowl of the same deck width, and a spout that cannot swing cannot serve the corners of the curve. Pull-out and pull-down hoses were treated as a third way to place water, useful where the fixed reach runs short.
Two further checks kept the list honest. Every model had to be a current product on its maker page, presented for sale rather than as a legacy design, and every model had to offer a spray function, since rinsing the curve is the daily task this sink shape makes awkward. Finish and styling were not scored at all: over a D-shaped bowl, geometry decides satisfaction long before color does.
Faucets for kitchen with d shaped sinks: the shortlist
Five faucets publish the reach or swivel evidence this sink shape demands. Three state a measured reach between 8 5/8 in and 9 in, and two state a full 360 degree swivel with a hose that extends the working range well past the fixed spout, which suits the wide front curve of the D shape.
Kraus Allyn KPF-4103SFS
The Allyn states the longest reach in this group, 9 in, from a body only 10 in tall with a spout height of 6 1/4 in. On a D-shaped sink that pairing is valuable: the stream lands far forward in the curved part of the bowl, while the low outlet keeps the drop short over a shallow basin.
Because the Allyn is a pull-out, the sprayer also travels to the work. Kraus lists a flow rate of 1.8 gpm, a ceramic cartridge the maker states is tested over 500,000 cycles, a metal body, easy-clean nozzles, and a low-profile design the maker describes as helping reduce splashing, especially in smaller sinks. A D-shaped bowl’s curved front holds more water area than its deck suggests, and a sprayer that comes to the dish rather than forcing the dish under the arch suits that shape.
The limit is the swivel: at 120 degrees the Allyn has the narrowest swing here, so serving both ends of a wide D-shaped bowl relies on the hose more than on spout rotation. It also mounts through a single hole. Buy the Allyn if reach matters most and your deck has one hole. Skip it if you want the spout itself to sweep the full width of the bowl.
- Pros: longest stated reach here; low body and low outlet; pull-out sprayer travels to the work
- Cons: 120 degree swivel is the narrowest here; single-hole mounting only
Kraus Oletto KPF-2820CH
The Oletto states a reach of 8 7/8 in and a swivel of 360 degrees, the strongest combination of the two key numbers in this group. The reach puts the stream near the middle of a D-shaped bowl, and the full swivel lets the spout track the curved front from corner to corner without moving the item being rinsed.
Kraus lists an overall height of 16 5/8 in and a spout height of 8 3/4 in, the tallest outlet here, which clears a stockpot set in the deep front of the bowl. The body is brass, the cartridge is ceramic with a maker-stated test life of 500,000 cycles, the flow rate is 1.8 gpm, and the spray face has easy-clean nozzles. The single handle rotates 90 degrees forward, which suits the narrow rear deck of a D-shaped sink where a backward-swinging handle would meet the backsplash.
The limit is mounting: the Oletto is a single-hole faucet, and the page opened presents it in chrome with spot free finishes also offered. Buy the Oletto if your deck has one hole and you want reach and rotation together. Skip it if your D-shaped sink has a three-hole deck that needs a plate.
- Pros: near-longest reach with full 360 degree swivel; tallest spout outlet here; brass body
- Cons: single-hole mounting only; taller body than the Allyn
Kraus Bolden KPF-1610SS
The Bolden states a reach of 8 5/8 in, a spout height of 6 1/4 in, and a swivel of 180 degrees. The 180 degree swing is the natural match for a D-shaped bowl mounted at the center of the rear deck: the spout sweeps a half circle that follows the front curve from one side to the other, which is where the basin actually is.
The maker lists a flow rate of 1.8 gpm, a ceramic cartridge, a metal body, and soft rubber easy-clean nozzles described as wiping away mineral build-up. The overall height is 18 3/4 in, the tallest here, yet the outlet sits low at 6 1/4 in, so the stream drops into the bowl rather than arcing across it. Mounting covers one or three holes, the most flexible pattern among the reach-led picks, and a soap dispenser is not included.
The limit is that tall body: over a D-shaped sink set under a low window or shelf, 18 3/4 in may not clear. Buy the Bolden if the space above the deck is open and you want a half-circle sweep with a low outlet. Skip it if clearance above the sink is tight or you need a full 360 degree swing.
- Pros: 180 degree sweep matches the D curve; low outlet; one or three hole mounting
- Cons: tallest body in the group; no soap dispenser included
Delta Essa 9113-AR-DST
The Essa’s case rests on movement rather than a published reach: Delta lists a 360 degree swivel and a 20-inch retractable hose, so the wand can be drawn out and aimed anywhere along the curved front of a D-shaped bowl. For rinsing the far corners of the curve, that hose travel does the work a fixed reach figure would otherwise have to promise.
The maker lists an overall height of 15-1/4 in, a flow rate of 1.8 gpm at 60 psi, MagnaTite docking that seats the wand with a magnet, and Touch-Clean spray holes that wipe clear of calcium and lime build-up with a finger. The valve package is the Euromotion DIAMOND valve with DIAMOND Seal Technology, and mounting is one or three holes on an 8 in pattern.
The limit is transparency on fit: the maker page does not state a spout reach, so a buyer measuring a specific deck-to-drain distance has to judge this model on swivel and hose instead. Buy the Essa if you rinse large items that sit in the curve and want the wand to come to them. Skip it if a published reach number is essential to your layout.
- Pros: full swivel plus hose travel covers the whole curve; magnetic docking; wipe-clean spray holes
- Cons: no spout reach stated on the maker page; mid-height body
Kraus Sellette KPF-1680SFS-KSD-80SFS
The Sellette states a 360 degree swivel and includes a soap dispenser in the same Spot Free Stainless Steel finish, which makes it the convenience pick for a D-shaped sink: the spout can sweep the full curve, and the dispenser takes the spare hole that many D-shaped decks carry at the rear corner.
Kraus lists a faucet height of 17 5/8 in, a flow rate of 1.8 gpm, a ceramic cartridge, metal construction, and easy-clean silicone nozzles on the spray face. Installation covers one, two, or three holes, the widest range in this group, which helps because D-shaped sinks are sold with several deck patterns. The pull-down wand handles the deep front of the bowl, where fixed spouts leave the corners of the curve unrinsed.
The limits are deck planning and height: the dispenser needs its own hole, and the 17 5/8 in body is tall. Buy the Sellette if you want full swivel, the widest mounting range, and the dispenser settled in one purchase. Skip it if your deck has no hole to spare for the dispenser.
- Pros: 360 degree swivel; dispenser included in a matching finish; one, two, or three hole mounting
- Cons: dispenser needs a deck hole; tall body for low clearances
Buying guide
A D-shaped sink rewards a buyer who measures the bowl, not just the deck. The checks below run from the tape work that decides stream placement, through swivel and hose questions, to the deck and clearance details that settle which of the shortlisted faucets can actually be installed over this sink shape.
Measure from the deck hole to the drain
On a D-shaped sink the mounting holes sit on the straight rear deck, and the drain sits forward of them, near the center of the curved bowl. Measure that distance and compare it with each model’s stated reach. A reach close to the measurement drops the stream near the drain, which is where rinsing water should land.
A reach well short of the drain leaves the stream against the shallow back of the bowl, where it splashes and runs forward anyway. A reach well beyond it strikes the curved front wall. The stated reaches in this group, from 8 5/8 in to 9 in, bracket the typical deck-to-drain span for this sink shape, which is why reach led the selection.
Swivel range follows the curve
The front of a D-shaped bowl is a curve, and covering it from a center mount takes swing. A 120 degree swivel covers the middle of the curve and leaves the corners to the hose. A 180 degree swivel sweeps the full front. A 360 degree swivel lets the spout point anywhere, even back over the deck.
Match the swivel to the bowl width. A compact D-shaped sink is well served by 120 to 180 degrees. A wide D-shaped bowl, or one set in a corner, rewards the full rotation of the Oletto, Essa, and Sellette. Remember that swivel figures describe the spout; the sprayer hose extends the working range on every pull-down and pull-out model here.
Spout height over a curved bowl
Spout height is the clearance between the deck and the outlet, and it decides what slides under the stream. D-shaped bowls are often deeper at the front, so a tall item placed in the curve sits lower than it would in a flat-bottomed sink, and a moderate spout height goes further than the number suggests.
The outlets here run from 6 1/4 in on the Allyn and Bolden to 8 3/4 in on the Oletto. For anything taller, every pick has a sprayer that pulls to the item. Choose spout height for your everyday items, and let the hose handle the exceptions, rather than buying the tallest arch by default.
Deck pattern and the rear strip
The rear deck of a D-shaped sink is a narrow straight strip, and it fills up fast: faucet body, handle swing, dispenser, and sometimes a separate sprayer all compete for it. Check handle movement against the backsplash. A forward-rotating handle, like the Oletto’s 90 degree forward rotation, needs no room behind the faucet at all.
Count the holes in the strip and match them to the faucet’s mounting pattern, including the hole a dispenser will take. The Sellette’s one, two, or three hole range and the Bolden’s one or three hole pattern cover most D-shaped decks; the single-hole Allyn and Oletto suit the cleanest modern decks.
Clearance above the sink
D-shaped sinks often sit in front of a window, and the arch has to clear the sill and any shelf above the deck. Overall heights here run from 10 in for the Allyn to 18 3/4 in for the Bolden, a wide spread that makes the overhead measurement decisive rather than optional.
Measure from the deck to the lowest obstruction, then keep a margin for the sprayer docked in the spout. If the margin is thin, the Allyn’s low profile solves the problem outright, and its 9 in reach means the shorter body gives up nothing in stream placement over this sink shape.
FAQ
Most D-shaped sink questions are really geometry questions: where the stream lands, how far the spout swings, and whether the deck strip can hold everything planned for it. The answers below use only the stated reach, swivel, and mounting figures from the shortlist.
What reach do faucets for kitchen with d shaped sinks need?
Enough to carry the stream from the rear deck to the drain area at the center of the curved bowl. In this group the stated reaches run from 8 5/8 in to 9 in, and those figures suit the deck-to-drain span of typical D-shaped sinks. Measure your own sink before ordering, because bowl sizes vary.
If your measurement falls beyond 9 in, favor a model with a long hose and full swivel, such as the Essa, so the sprayer covers the remaining distance. If it falls well short, a shorter reach keeps the stream off the curved front wall, and the pull-out Allyn can be drawn back toward the user as needed.
Does swivel range matter more than reach for this sink shape?
They do different jobs. Reach places the stream front to back, which the D shape makes critical because the bowl extends forward from the deck. Swivel places it side to side along the curve. A faucet strong in only one can still work, but the Oletto pairs both, which is the more complete answer.
For a narrow D-shaped bowl, reach is the priority. For a wide one, swivel joins it. Judge your bowl width honestly, and remember the sprayer hose adds working range in both directions on every model in this shortlist.
Can a pull-down faucet work on a D-shaped sink?
Yes. Four of the five picks here are pull-down models, and their wands are arguably better suited to the D shape than a fixed spout, because the wand can be drawn into the curved front corners that a fixed stream angle cannot reach. Docking systems, magnetic on the Essa and standard on the Kraus models, keep the wand seated when not in use.
The pull-out alternative, the Allyn, keeps the body lower and pulls the sprayer toward the user. Choose between them on the space above your deck: open space favors the taller pull-down arches, tight space favors the pull-out.
Where does a soap dispenser go on a D-shaped deck?
Usually in the spare hole at one end of the rear deck strip. The Sellette includes its dispenser in the box, in the same finish as the faucet, and its one, two, or three hole mounting range leaves room in the plan for that extra hole. Measure the strip first, because narrow decks sometimes carry only the faucet holes.
If no spare hole exists, a dispenser can be drilled into many deck materials, but that is a job to price and plan before ordering, not after. The other picks here leave the layout open by not bundling a dispenser at all.
Is a tall arch a problem over a D-shaped sink?
Only where something hangs above the deck. The Bolden stands 18 3/4 in tall over this sink shape, which clears most window sills but not every shelf or cabinet run. Its outlet, though, sits at 6 1/4 in, so its stream behavior is gentle despite the tall body.
Measure the overhead space first. If it is open, a tall arch adds pot clearance and a strong look. If it is not, the Allyn delivers the longest reach in this group from a 10 in body, which is the neater solution for a low window over a D-shaped bowl.
Conclusion
For a D-shaped sink, start with the Kraus Allyn for the longest stated reach from the lowest body, or the Kraus Oletto where reach and full swivel matter equally. The Delta Essa covers the curve by hose, and the Sellette adds the dispenser. Measure the deck-to-drain span first; the right pick is the one whose stated numbers match it.