Updated Nov 17, 2026· 16 min read

Key takeaways

  • Compare the best washers for low friction in PTFE, nylon, and UHMW. Check sizes, thicknesses, and materials to pick a washer that slides smoothly in your joint.

When a joint sticks, squeaks, or binds, the washer between the parts often decides how freely it moves. The best washers for low friction use slick materials such as PTFE, nylon, and UHMW polyethylene to let parts slide, turn, and release without grinding. This guide compares six real washer lines by material, size range, and fit.

Quick verdict

For most low friction joints, PTFE gives the slickest surface and the widest chemical resistance, while UHMW gives tough impact resistance at a lower material cost. Nylon sits in the middle with good strength and easy sizing. Pick the material first, then match the inside diameter, outside diameter, and thickness to your screw and your joint.

Product Type Best for Key spec Main limit
McMaster-Carr UHMW Polyethylene Washers UHMW flat washer Impact and vibration joints Max 180 degrees F Thinner sizes have narrow thickness ranges
WCL Nylon Standard Flat Washers Nylon flat washer General purpose screw joints Thickness 0.032 to 0.125 inch Standard range only, no stated temperature range
CDE Fasteners Nylon Flat Washers Type 6/6 nylon flat washer Bulk orders of common sizes Sold in lots of 5,000 Bulk pack size suits large orders only
Fastenal Flat Washer Type PTFE White PTFE flat washer Chemical and slick joints White PTFE, ID tolerance plus or minus 0.010 inch Thin PTFE can creep under sustained load
Bulte DIN 125A PTFE Plain Washers PTFE plain washer to DIN 125A Metric standard joints Sizes M1.6 to M90 Plastic dimensions may vary from metal standards
New Process Fibre Custom Washers Custom PTFE, UHMW, and nylon washers Odd sizes and special materials OD 0.093 to 12.000 inches Custom orders need exact dimensions up front

Start with PTFE when the joint must slide freely and face chemicals or moisture, and start with UHMW when the joint takes knocks, vibration, or repeated movement. Nylon earns its place when you need a strong, light washer in a common screw size with a wide choice of thicknesses.

How we selected

We selected washers from published maker and distributor pages that state the material, the dimensions, and the intended use in plain terms. Each product below comes from a page we opened and read, and every size, thickness, and temperature figure in this guide comes from that page.

The keyword here means hardware washers, not laundry machines, so every product below is a flat or plain washer made from PTFE, nylon, or UHMW polyethylene.

Best washers for low friction in detail

Each product below is a distinct washer line from a different maker or distributor, with its own material, size range, and strength. Read the size tables with care, because two washers for the same screw can differ in outside diameter and thickness. The notes on limits matter as much as the specs.

McMaster-Carr low friction UHMW polyethylene washers

These UHMW washers suit readers who want a tough, slick washer for joints that move, vibrate, or take knocks. The maker describes them as low friction and impact resistant, with a slippery surface that reduces friction between the washer, the fastener, and the mounting surface. They also resist bumps and vibration without cracking or denting.

The maker lists these washers as lightweight, nonconductive, and naturally rust resistant, and notes that they are commonly used in electronics and automation.

Size coverage runs from No. 2 screws up to 1-1/2 inch screws, and from M2 to M20 in metric sizes. A No. 10 example lists an inside diameter of 0.219 inch, an outside diameter of 0.500 inch, and a thickness of 0.036 inch to 0.065 inch, in a pack of 25 with part number 95649A129. A 1/4 inch example lists an inside diameter of 0.265 inch, an outside diameter of 0.500 inch, and a thickness of 0.026 inch to 0.036 inch, also in a pack of 25.

Most sizes list a maximum of 180 degrees F, and an M10 example lists a minimum of minus 30 degrees F with an inside diameter of 10.5 mm, an outside diameter of 20.0 mm, and a thickness of 1.8 mm to 2.2 mm, in a pack of 10. Pros include a slick surface, strong impact resistance, and a very wide size range. Cons include the 180 degree F ceiling and small pack counts on the largest sizes. Buy if your joint moves or takes bumps and stays below the stated limit. Skip if the joint runs hot or faces aggressive chemicals.

WCL nylon standard flat washers

These nylon washers suit readers who need a plain, dependable washer in a common screw size and want four thickness choices for the same screw. The maker lists a standard table by screw size, with outside diameter, inside diameter, and thickness for each code. That structure makes it easy to keep the screw size fixed and change only the thickness.

The standard table covers screw sizes from 2 up to 1/2 inch, in four standard thicknesses. A 1/4 inch example, code FW500257062, lists an outside diameter of 0.5 inch, an inside diameter of 0.257 inch, and a thickness of 0.062 inch. A 1/2 inch example, code FW750505125, lists an outside diameter of 0.75 inch, an inside diameter of 0.505 inch, and a thickness of 0.125 inch.

The maker also lists a special flat washer table for sizes outside the standard pattern. Examples include code FW560379375, with an outside diameter of 0.56 inch, an inside diameter of 0.379 inch, and a thickness of 0.375 inch, and code FW1000350500, with an outside diameter of 1 inch, an inside diameter of 0.35 inch, and a thickness of 0.5 inch. The maker does not state a temperature range or a load rating on the page we opened.

Pros include a clear size table, four standard thicknesses per screw size, a special range for thick spacer duty. Cons include no stated temperature range on the page, no stated load rating, and no pack quantity stated on the page. Buy if you need a common nylon washer in a known screw size and want to pick the thickness precisely. Skip if your joint runs hot or carries a heavy load and you need a stated temperature or load figure before you order.

CDE Fasteners nylon flat washers, type 6/6 nylon

These washers suit readers who order in bulk and want a named nylon grade in a common size. The maker lists them as standard flat washers in Type 6/6 nylon, with sizes given as screw size by outside diameter by thickness. That naming matters, because Type 6/6 nylon is a specific grade, not a generic label.

The size list covers small machine screws up to 1/2 inch bolts. A 2 by 1/4 by 0.032 inch size fits a No. 2 screw with a 1/4 inch outside diameter and a 0.032 inch thickness. A 1/4 by 1/2 by 0.062 inch size fits a 1/4 inch screw with a 1/2 inch outside diameter and a 0.062 inch thickness. A 1/2 by 3/4 by 0.093 inch size fits a 1/2 inch screw with a 3/4 inch outside diameter and a 0.093 inch thickness.

Each size on the page lists a quantity of 5,000, which marks this line as a bulk buy rather than a small repair pack. The maker also states that it stocks over 40,000 fasteners online and offers same day shipping Monday through Friday. The maker does not state a temperature range, a thickness tolerance, or a load rating on the page we opened.

Pros include a named Type 6/6 nylon grade, a clear size list from small screws to 1/2 inch bolts, bulk quantities for repeat use, and same day shipping Monday through Friday. Cons include the 5,000 piece quantity per size, no stated temperature range, and no stated thickness tolerance on the page. Buy if you need a large quantity of one nylon washer size for repeated assemblies. Skip if you need only a few washers, or if you need a stated heat or load limit before you order.

Fastenal flat washer, type PTFE

This PTFE washer suits readers who want the slickest common washer material and a written dimensional standard behind it. The maker publishes product standard FW.PTFE, revision 05, dated December 2, 2025, for a flat washer of type PTFE. The standard states the material as white PTFE.

The table covers small washers up to large ones. A washer with an inside diameter of 0.250 inch, an outside diameter of 0.500 inch, and a thickness of 0.062 inch fits a 1/4 inch joint. A washer with an inside diameter of 0.281 inch, an outside diameter of 0.500 inch, and a thickness of 0.031 inch gives a thinner option for the same outside diameter. At the large end, a washer with an inside diameter of 0.812 inch, an outside diameter of 2.000 inches, and a thickness of 0.100 inch spreads load over a wide area.

Tolerances are stated in the standard, which helps when a joint needs a close fit. The inside diameter tolerance is plus or minus 0.010 inch. Thickness tolerances run from plus or minus 0.001 inch on a 0.010 inch thickness, to plus or minus 0.002 inch on a 0.031 inch thickness, to plus or minus 0.005 inch on a 0.062 inch thickness, to plus or minus 0.01 inch on a 0.100 inch thickness. PTFE is the slickest material in this guide, but thin PTFE can slowly deform under a sustained load, so use a thicker washer, or one with a larger outside diameter, when the load is steady.

Pros include white PTFE with a very slick surface, a written product standard with revision history, stated thickness tolerances, and a wide size table. Cons include no stated temperature range in the standard, no pack quantity stated, and the creep risk that comes with thin PTFE under sustained load. Buy if you need a slick, chemical resistant washer with a documented size and tolerance table. Skip if the joint carries a heavy steady load on a thin washer, or if you need a stated temperature limit before you order.

Bulte DIN 125A PTFE plain washers

These washers suit readers who build to metric standards and want a PTFE washer in a named DIN and ISO size. The maker lists plain washers to DIN 125A and ISO 7089, with PTFE listed among the materials for that standard. The same page lists matching standards for other shapes in the same family.

The DIN 125A and ISO 7089 range runs from M1.6 to M90, which covers tiny instrument screws up to very large bolts. For socket head screws, the DIN 433 and ISO 7092 range runs from M2 to M36, with a smaller outside diameter that suits a socket head. For wide load spreading, the DIN 9021 and ISO 7093-1 fender range runs from M2 to M20, with a large outside diameter that suits soft materials and oversize holes.

The maker describes PTFE as a material with excellent resistance to aggressive media. The maker also notes that plastic washers are often described as ISO-like or DIN-like, because dimensions and tolerances may vary due to material properties, with slight deviations from shrinkage. That note matters: do not assume a plastic DIN washer matches a steel DIN washer to the last fraction of a millimeter.

Pros include a named DIN 125A and ISO 7089 standard, a very wide M1.6 to M90 size range, PTFE with strong resistance to aggressive media, and matching fender and socket head ranges in the same family. Cons include no thickness or temperature figure on the overview page, plastic dimensions that may vary from metal standards, and no pack quantity stated. Buy if your drawing calls out a metric DIN size and you want that size in PTFE. Skip if you need a stated thickness or temperature figure from the overview page alone, or if your joint uses inch screws rather than metric.

New Process Fibre custom plastic washers

These washers suit readers whose joint needs a size, a material, or a shape that no standard table covers. The maker is an ISO 9001:2015 non-metallic stamping company that makes flat and specialty washers from a large range of materials, including nylon, PTFE, UHMW, and acetal.

Size coverage is the widest in this guide. The maker states that it fabricates washers with outside diameters from 0.093 inch to a maximum of 12.000 inches, thicknesses from 0.005 inch to 0.187 inch, and quantities ranging from just 1 into the millions per order. It also states that it holds over 10,000 washer dies in stock and can meet requirements in as little as 1 week or less.

For low friction duty, the maker states that PTFE washers offer low surface energy, friction resistance, and resistance to aggressive media, while nylon, Nylon MDS, and Delrin washers provide strength for mechanical assemblies and high wear resistance. That contrast helps a reader choose: pick PTFE when slipperiness and chemical resistance lead, and pick nylon or acetal when strength and wear lead. The page does not state a temperature range or a load rating for a specific custom washer.

Pros include the widest size range in this guide, orders from 1 piece into the millions, over 10,000 dies in stock, lead times as short as 1 week or less. Cons include no fixed size table for custom parts, no stated temperature range for a specific washer, and the need to supply exact dimensions before ordering. Buy if your joint needs an odd size, a special material, or a small prototype run. Skip if you want an off the shelf washer in a standard size with a published thickness table.

Buying guide

Buying a low friction washer is a sizing job first and a material job second. A slick material cannot fix a washer that is too small, too thin, or drilled for the wrong screw. Work through the points below in order before you order. A few minutes with a caliper and the size table saves a return and a stalled assembly.

Match the material to the joint in the best washers for low friction

Start with what the joint must do, not with what looks cheapest in the catalog. PTFE gives the slickest surface and the strongest resistance to chemicals and moisture, so it leads when parts must slide freely and face harsh fluids. UHMW gives tough impact resistance and a slick surface, so it leads when joints take knocks and vibration.

PTFE can creep under a steady load, especially in thin sizes. UHMW has a stated ceiling of 180 degrees F in the McMaster line, which rules out hot joints. Nylon is strong for its weight but absorbs moisture over time, which can change its fit in damp joints.

Measure inside diameter, outside diameter, and thickness

Measure the screw shank, not the thread crest, and pick an inside diameter that clears the shank with a small, even gap. A hole that is too tight will bind on the screw, while a hole that is too loose will let the washer sit off center and rub on one edge.

Pick the outside diameter by the surface under the washer. A larger outside diameter spreads the load over more area and protects soft surfaces, which is why fender washers exist, but it can also overhang a narrow part or foul a nearby feature.

Check temperature and chemical exposure

Write down the hottest temperature the joint will see in normal use, not just at room temperature on a bench. Then compare that figure with the stated maximum for the material you picked. The McMaster UHMW line states a maximum of 180 degrees F, and that figure is a hard stop for that line.

PTFE and nylon lines in this guide do not state a temperature range on the pages we opened, so do not guess a limit for them; ask the maker for the figure that covers your joint. List every fluid the washer will touch, including cleaners, oils, solvents, and washdown chemicals. PTFE resists a wide range of aggressive media, as the Bulte page states, and that makes it the first choice for chemical joints.

Think about load, creep, and wear

A washer under a bolt carries the full clamp load of that bolt across a small ring of plastic, so load matters even when the washer looks simple. A thin washer under a high load can deform, and PTFE in particular can creep under a steady load over weeks and months.

When the load is steady rather than brief, pick a thicker washer, a larger outside diameter, or a stronger material such as nylon or acetal, and check the joint again after it has been in service. Wear comes from movement, not just from load. A washer in a sliding joint rubs on every cycle, so a soft material will wear faster than a hard one, and a washer that is too thin will wear through sooner.

Order the right quantity and keep spares

Count the washers you need per assembly, then add spares for drops, misfits, and future repairs. Small washers are easy to lose on a bench, and a single missing washer can stall a job. Pack sizes in this guide range from 1 piece to lots of 5,000, so order a few extra of the size you use most.

The McMaster UHMW line lists packs of 25, 10, 5, and 1 depending on size, so the pack size changes with the size you pick. The CDE nylon line lists lots of 5,000, which suits a shop but not a single repair. The New Process Fibre line takes orders from 1 piece into the millions, which suits both a prototype and a production run. Store washers flat, dry, and out of sunlight, and keep different materials in separate bags so they do not get mixed.

FAQ

These questions cover the points readers ask most about low friction washers, from the difference between PTFE and nylon to the right way to measure a washer. Each answer stays with the facts on the maker pages in this guide. Use the answers as a starting point, then check the size table for your own joint.

What is a washer of this kind

A low friction washer is a flat ring of slick plastic, such as PTFE, nylon, or UHMW polyethylene, that sits between a fastener and a surface, or between two moving parts, so they slide past each other with less drag. The washer spreads the load of the screw head and protects the surface under it.

In this guide, every product is a hardware washer of that kind, not a laundry machine part. The low friction effect comes from the material itself, not from oil or grease on the surface.

Is PTFE better than nylon for low friction joints

PTFE gives a slicker surface than nylon and stronger resistance to chemicals and moisture, so it leads when the joint must slide freely in a harsh setting. Nylon gives more strength for its size and a wider choice of standard thicknesses. Neither material wins in every joint.

The right pick depends on heat, load, and fluids as much as on friction. PTFE has a weak point to weigh: thin PTFE can creep under a sustained load, which means it slowly deforms and the joint can lose clamp over time. Nylon has a different weak point: it can absorb moisture, which can change its fit in a damp joint.

How do I measure a washer before ordering

Measure three figures with a caliper: the inside diameter across the hole, the outside diameter across the full ring, and the thickness at the edge. Write each figure down with its unit, inches or millimeters, and do not mix units in one order. Then measure the screw shank that will pass through the hole.

Measure the space the washer must fit into, including any nearby step, slot, or wall that could foul a wide washer. Compare your figures with the maker size table row by row. The inside diameter must clear the screw shank with a small even gap, the outside diameter must sit fully on the bearing surface without overhang, and the thickness must leave enough thread engaged after the washer is in place.

Can a low friction washer replace a bearing

A low friction washer can act as a simple thrust face or spacer in a light, slow joint, but it does not replace a bearing in a fast, heavy, or precise assembly. A washer spreads load and gives a slick face, yet it has no rolling elements or stated speed rating.

A bearing is built for rotation under load at speed, with clearances and ratings that a flat washer does not carry. Use a washer as a thrust face when the movement is slow, the load is light, and the alignment is simple, such as a pivot, a hinge, or a knob that turns by hand. Move to a proper thrust bearing when the joint spins fast, carries a heavy axial load, or needs precise end play over a long service life.

Why does my PTFE washer feel loose after a few months

A PTFE washer can feel loose after months in service because thin PTFE can creep under a sustained clamp load, slowly deforming and letting the joint lose some of its grip. The washer may look intact, yet its thickness has changed enough to slacken the assembly.

Heat, a high initial load, and a small outside diameter all make creep more likely, because they raise the stress on a small ring of soft plastic. Check the joint by measuring the washer thickness and comparing it with the figure on the maker table, and look for a groove or a shiny worn ring on the washer face. If the washer has thinned, replace it with a thicker PTFE washer, a washer with a larger outside diameter, or a stronger material such as nylon or acetal, and recheck the clamp after the joint has settled.

Conclusion

Pick PTFE for the slickest slide and strongest chemical resistance, UHMW for tough impact duty below 180 degrees F, and nylon for strong everyday joints in common sizes. Measure the screw, match all three dimensions, and keep a few spares on hand. A washer that fits on all three measures will slide smoothly and stay put.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.