Key takeaways
- Find the best washers for folding knives, from phosphor bronze washers to Nylatron and stainless steel sets, with sizes, fits, and care tips for smooth pivots.
A gritty pivot, side-to-side blade play, and a blade that drags on the liner often trace back to one small part. The best washers for folding knives match your pivot size, suit your carry conditions, and keep the blade turning on a clean, flat surface. This guide compares seven real washer sets, from phosphor bronze to Nylatron.
Quick verdict
If you want one short answer, start with phosphor bronze for hard use, Nylatron for a quiet low-cost pivot, and hardened steel races for loose bearings. The sets below cover those three jobs, plus a model-specific set for three popular Benchmade folders.
Phosphor bronze is the safe default for most folding knife pivots. The maker guidance we read describes it as a material that holds a polished surface well, resists wear, and works smoothly with a thin film of oil. New washers can feel stiff at first, then burnish into a controlled action, and the simple sliding surface is easier to clean than a caged bearing.
Nylatron and other polymer washers suit a different job. They run quiet, feel smooth right away, and cost little, which makes them a sound pick for light-duty folders. The trade-off is wear: polymer washers give up service life sooner than bronze. Stainless steel washers fill the gap where a maker needs a thin, hard spacer or a race for loose bearings.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| KnivesPlus oversized pivot washers | Phosphor bronze | Bugout, Mini Bugout, Bailout owners | 2 oversized washers | Fits only the three listed models |
| USAKnifeMaker phos bronze washer | Phosphor bronze | Folder builds, bronze bushings | 0.193 in ID, 0.320 in OD, 0.020 in thick | Pair, one pair per pivot |
| USAKnifeMaker Nylatron washer | Nylatron polymer | Quiet, low-cost pivots | 0.020 in thick, 1/8 in ID, 3/8 in OD | Lower wear resistance than bronze |
| USAKnifeMaker stainless steel washer, thin | Stainless steel | Fine pivot spacing | 0.0118 in thick, 0.205 in ID, 0.355 in OD | Very thin, easy to bend or lose |
| USAKnifeMaker stainless steel washer, thick | Stainless steel | Small pivots, thicker spacer | 0.020 in thick, 0.245 in OD | Listed inside diameter needs checking |
| USAKnifeMaker race washers 1 | Hardened stainless steel | Loose-bearing pivots | 0.052 in thick, hardened to 61 HRC | For bearing races, not plain pivots |
| USAKnifeMaker race washers 2 | Hardened stainless steel | Loose-bearing pivots | 0.055 in thick, hardened to 61 HRC | Built for bearing races, not plain pivots |
How we selected
We selected these seven washer sets from published product pages and maker descriptions, not from memory or guesswork. Each product below is a real washer set sold for folding knife pivots, with its material, dimensions, and fit stated on a page we opened and read before writing.
The list favors parts that fit the keyword exactly: washers that sit in a folding knife pivot, between the blade tang and the handle liners or frame. That ruled out general hardware washers and whole knives that merely contain washers, since this guide is about the washer part itself. Every product below is sold as a washer set you can fit to a pivot you already own or a folder you are building.
We looked for a spread of materials and sizes: phosphor bronze for hard use, Nylatron for quiet pivots, stainless steel for thin spacers, and hardened race washers for loose-bearing builds. Where a listing gave a dimension that looked wrong, we flagged the number instead of printing it as certain.
The best washers for folding knives
These seven sets cover the main ways a folding knife pivot is built: a model-specific bronze upgrade, general bronze and polymer washers, thin steel spacers, and hardened races. Read the fit notes, since a washer that is close in size is not the same as a washer that fits.
Replacement oversized pivot washers for Benchmade Bugout, Mini Bugout, Bailout
This KnivesPlus set is the direct pick in this guide for owners of three specific Benchmade folders. The washers are phosphor bronze, made in the United States, and the set includes 2 oversized washers for the Bugout 535, the Mini-Bugout 533, and the Bailout 537.
The maker describes these washers as larger than stock, and states that the extra surface area helps create a smooth action while reducing blade play. A wider washer spreads the load across more of the blade tang, which steadies the blade side to side and keeps centering easier to hold.
The main limit is fit. The maker lists only the Bugout 535, Mini-Bugout 533, and Bailout 537, so owners of other models should not assume the set will work. Some owners report other Benchmade fits, but the maker does not state that, so treat any other fit as unconfirmed.
- Phosphor bronze construction suits hard-use pivots
- Oversized face gives more contact area than stock washers
- Listed fit covers only three models
- No thickness is stated on the product page
Buy if you own a Bugout 535, Mini-Bugout 533, or Bailout 537 and want less blade play.
Skip if your knife is a different model, or if you need a stated thickness for your pivot stack.
Washer phos bronze 0.193 inch ID x 0.320 inch OD x 0.020 inch thick
This USAKnifeMaker washer is a general phosphor bronze pivot washer sold by the pair for folder builds. The maker lists an inside diameter of 0.193 inch, an outside diameter of 0.320 inch, and a thickness of 0.020 inch, with a stock keeping unit of FKP-Wash-PB-020-193-320.
The maker describes these washers as the perfect size for use with its bronze pivot bushings, and states that they will provide a smooth action while taking up minimum space. The washer rides on the pivot bushing, the blade tang rides on the washer, and the 0.020 inch thickness adds real spacing.
This washer is for knife makers and owners who build or service folding knives and know their pivot size. It suits balisong builds too: the maker notes that balisongs need one pair of washers per pivot, and that the pivot and bronze bushing shown are not included. One pair covers only one pivot, so check your bushing diameter against the 0.193 inch inside diameter before ordering.
- Phosphor bronze suits long service in a folder pivot
- Stated dimensions cover ID, OD, and thickness
- Pairs with bronze pivot bushings from the same maker
- One pair covers only one pivot
- Needs a matching bushing size to work as intended
Buy if you are building a folder and your pivot bushing matches the 0.193 inch inside diameter.
Skip if you need a washer for a named production knife, or a larger outside diameter.
Washer Nylatron 1/8 inch inside hole diameter
This USAKnifeMaker Nylatron washer is the polymer pick in this guide, sold by the pair for folding knife pivots. The listing centers on a 1/8 inch inside hole diameter, and the variant shown lists 0.020 inch thickness, 1/8 inch inside diameter, and 3/8 inch outside diameter.
Nylatron is a nylon-based polymer, and the maker describes these washers simply as washers for your folding knife. The material brings a quiet, slightly damped action that feels smooth from the first opening, with no break-in period like new phosphor bronze.
This washer is for builders who want a low-cost pivot surface and do not need the wear resistance of bronze. It suits slip joints, simple liner locks, and utility folders. The main limit is wear life: polymer washers give up service life sooner than bronze in a knife that is opened often, and they can compress under load.
- Polymer action feels smooth from the first use
- Quiet, slightly damped pivot feel
- Low cost per pair for builders
- Lower long-term wear resistance than phosphor bronze
- Can compress under heavy pivot load
Buy if you want a quiet, low-cost washer for a light-duty folder or a first build.
Skip if your knife gets hard daily use, or if you want the longest service life.
Stainless steel washer, pair, 0.0118 inch thick x 0.205 inch ID and 0.355 inch OD
This USAKnifeMaker stainless steel washer pair is the thinnest spacer in this guide, made for fine pivot tuning. The maker lists an inside diameter of 0.205 inch, or 5.2 mm, an outside diameter of 0.355 inch, or 9 mm, and a thickness of 0.0118 inch, or 0.3 mm.
A washer this thin is a tuning part, not a structural upgrade. It lets a maker add a hair of spacing to a pivot stack without changing the feel of the knife, which is useful when a blade sits slightly off center or rubs a liner. Stainless steel holds its shape well at this thickness and resists corrosion.
This pair is for builders who measure their pivots and adjust in small steps. It suits a folder that is almost right, where one thin washer on a side brings the blade into center or stops a faint rub. The main limit is handling: a 0.0118 inch washer is easy to bend or lose during assembly, and it will not fix a pivot that is far out of alignment.
- Very thin profile for fine spacing adjustments
- Stainless steel resists corrosion in daily carry
- Both inch and metric dimensions are stated
- Thin washers bend and crease easily
- Adds only a small amount of spacing
Buy if you need a fine spacing correction and your pivot matches the 0.205 inch inside diameter.
Skip if your pivot needs a large spacing change, or a washer that forgives rough handling.
Stainless steel washer, pair, 0.020 inch thick x 0.007 inch ID and 0.245 inch OD
This USAKnifeMaker stainless steel washer pair is the thicker steel spacer in this guide, and it needs a careful read before ordering. The maker lists an inside diameter of 0.007 inch, or 0.178 mm, an outside diameter of 0.245 inch, or 6.22 mm, and a thickness of 0.020 inch, or 0.508 mm.
The 0.020 inch thickness and 0.245 inch outside diameter are clear and useful: this is a compact steel washer that adds a firm spacer to a small pivot stack. Stainless steel gives a hard, flat bearing face that holds its shape under pivot tension.
The problem is the listed inside diameter. A hole of 0.007 inch is far too small to fit any normal knife pivot, so the number as printed looks like a listing error rather than a real dimension. Confirm the true inside diameter with the maker before ordering, and measure the washer on arrival. This pair is for a buyer who is willing to verify one dimension first.
- Thicker 0.020 inch steel profile for real spacing
- Compact 0.245 inch outside diameter suits small pivots
- Stainless steel holds its shape under pivot tension
- Set of 2 covers both sides of one pivot
- Listed inside diameter of 0.007 inch looks like a listing error
- True fit must be confirmed before ordering
Buy if you need a 0.020 inch steel spacer with a 0.245 inch outside diameter and have confirmed the inside diameter.
Skip if you want a washer with a fully stated fit, or if you are ordering for a named knife model.
Race washers 1
These USAKnifeMaker race washers are a hardened steel race for a loose-bearing pivot, sold as a set of 2. The maker lists a thickness of 0.052 inch, an outside diameter of 0.229 inch, and an inside diameter of 0.115 inch, with the race hardened to 61 HRC.
A race washer gives loose ball bearings a hard, grooved track to roll in. The maker states that these races fit a typical 1/8 inch barrel pivot, and that the groove will perfectly fit the roller balls. In a loose-bearing setup, the balls would otherwise have to break in their own groove, which takes time. The maker says these races remove that step.
This set is for makers who build folding knives on loose bearings and want a clean, repeatable bearing track. The hardened 61 HRC surface resists the wear that hard bearing balls can cause in softer handle material. The main limit is that race washers are not plain pivot washers: they belong in a bearing pivot with a milled pocket, and the maker notes that the outside diameter is the main concern when milling.
- Hardened to 61 HRC for a durable bearing track
- Groove fits the roller balls in a loose-bearing setup
- Removes the need to break in a ball groove
- Built for bearing pivots, not plain washer pivots
- Needs a milled pocket sized to the outside diameter
Buy if you are building a loose-bearing folder with a milled race pocket and a 1/8 inch pivot.
Skip if your knife runs on plain washers, or if you do not want to mill a pocket.
Race washers 2
These USAKnifeMaker race washers are the close sibling of the set above, with slightly larger dimensions. The maker lists a thickness of 0.055 inch, an outside diameter of 0.236 inch, and an inside diameter of 0.127 inch, with the race hardened to 61 HRC.
Like the first race washer set, this one is made for a loose-bearing pivot on a typical 1/8 inch barrel pivot. The maker states that the races are hardened and have a groove that will perfectly fit the roller balls, and that using the races removes the step of breaking in a ball groove.
The difference between the two race washer sets is small but real: this set is 0.055 inch thick against 0.052 inch, with an outside diameter of 0.236 inch against 0.229 inch, and an inside diameter of 0.127 inch against 0.115 inch. That makes it the pick when your milled pocket is cut to the larger size. Measure the pocket first.
- Hardened to 61 HRC for a durable bearing track
- Slightly larger size suits a larger milled pocket
- Groove fits the roller balls in a loose-bearing setup
- Built for bearing pivots, not plain washer pivots
- Needs a milled pocket sized to the outside diameter
Buy if your loose-bearing folder has a pocket milled to a 0.236 inch outside diameter.
Skip if your pocket matches the smaller race washer set, or your knife runs on plain washers.
Buying guide for folding knife washers
Buying a pivot washer is a measuring job before it is a shopping job. The washer has to match your pivot in three dimensions at once, suit the way you carry the knife, and survive the conditions you use it in. Get those points right and the pivot takes care of itself.
Match the inside diameter to your pivot in the best washers for folding knives
The inside diameter is the first number to check, because the washer has to pass over the pivot pin or bushing and turn freely around it. Look for a close sliding fit, not a tight press fit or a loose rattle, since a binding washer drags and a loose one lets the blade wander.
Common pivot sizes cluster around 1/8 inch and 3/16 inch, but custom folders and older knives vary widely, so never guess from the knife model alone. Measure the old washer and the pivot together before ordering. For a model-specific set like the oversized Bugout washers above, the maker has done that measuring for you.
Match washer thickness to your pivot stack
Washer thickness sets the spacing between the blade tang and the liners, and small changes here have a large effect on feel. A washer that is too thick adds drag, while one that is too thin leaves a gap that invites blade play. The sets here range from 0.0118 inch to 0.055 inch.
When you are tuning a pivot, change one thing at a time. Fit one thickness, assemble the knife, and check centering and play before trying another size. Keep the old washers until the new ones prove themselves. A small offset often needs only a thin washer on one side, while a large offset points to a bent liner or a worn pivot.
Choose the washer material for your use
Phosphor bronze is the default for hard-use folders because it holds a polished surface, resists wear, and works smoothly with a thin film of oil. It can feel stiff when new, then burnishes into a controlled action with use, which many owners prefer in a work knife.
Teflon and other polymer washers feel slick from the start and run quietly, but they compress more easily and give up service life sooner under hard use. Nylatron sits in the same family: soft, quiet, and slightly damped, with lower wear resistance than bronze. Stainless steel suits thin spacers and bearing races.
Keep a spare pair on hand
Pivot washers are small, cheap, and easy to lose, and a knife with a missing washer is a knife that should not be carried. Keep one spare pair for each folder you service often, stored flat in a labeled bag with the knife model and dimensions written on it.
Spares also let you experiment without risk. If you want to try a thicker washer to tighten up blade play, or a polymer washer to quiet a pivot, you can fit the spare and go back to the original set if the change does not suit you. Washers are wear parts, so a spare set is the part you will reach for most often.
Clean and oil the pivot the right way
Most pivot problems are cleaning problems, not washer problems. Lint, dust, and dried oil collect around the washers and turn a smooth pivot gritty, and the fix is a careful cleaning rather than a new part. Work over a clean surface and keep the small parts in order.
When you reassemble, use only a very small amount of light lubricant on the washer faces. A thin film is enough: too much oil attracts grit and turns into paste, while a dry washer drags and wears faster. Tighten the pivot screw in small steps, and stop when the blade is centered with no side play.
FAQ
These are the questions buyers ask most often when they shop for folding knife washers, answered from the product pages and maker guidance used here. If your question is not here, measure your pivot and read the fit notes on the product page before ordering.
What size washer does my folding knife need?
The size you need comes from your own knife, not from a chart. Measure the pivot pin or bushing diameter for the inside diameter, measure the space the washer has to cover for the outside diameter, and measure the old washer or the gap in the stack for thickness.
If you cannot measure the pivot, a model-specific set is the safer route, since the maker has matched the part to named models. For a custom folder, calipers are the only reliable tool. Guessing often ends with a washer that binds, rattles, or sits off center.
Are phosphor bronze washers better than Teflon washers?
Neither material is better in every case, and the right pick depends on how you use the knife. Phosphor bronze lasts longer, holds its shape under load, and gives a controlled action that improves as the faces burnish together. It is the standard pick for hard-use folders and knives that see dirt and dust.
Teflon washers feel slicker from the start and run very quietly, which suits light-duty folders and owners who want a smooth action with no break-in. The trade-off is that Teflon compresses more easily and wears sooner under hard use. For a daily work tool, bronze is the safer choice.
How long do folding knife washers last?
Washer life depends on material, use, and care, so no single number covers every knife. Phosphor bronze washers often last for years of regular carry, since the material resists wear and works with a thin film of oil. Polymer washers wear sooner, especially in a knife that is opened often.
The signs that a washer needs replacing are uneven wear, a washer that has thinned on one side, a pivot that stays gritty after cleaning, or blade play that returns soon after you adjust the pivot. Replace washers in pairs, even if only one side looks worn.
Can I stack two thin washers on one side?
Stacking two thin washers on one side can work as a tuning step, but it is a compromise rather than a clean fix. Two washers can shift against each other and trap grit between their faces. If you stack washers, use two of the same material and keep the faces clean.
A better fix is usually a single washer in the correct thickness. Keep a range of thicknesses on hand so you can reach for the right one instead of stacking. If the stack needs a large correction, look for a bent liner or a worn pivot first.
Do washers change how a knife opens?
Yes, washers shape the opening feel in a direct way. A washer pivot gives a controlled, deliberate action, with the blade sliding across a broad flat surface instead of rolling on small bearing balls. That feels slower than a bearing pivot, but it stays consistent when the pivot gets dirty.
New phosphor bronze washers can feel stiff at first, then smooth out as the faces burnish together with use. Polymer washers feel smooth right away but may not hold that feel as long. Oversized washers can reduce blade play, while one that is too thick adds drag.
Conclusion
Start with phosphor bronze for hard use, pick the oversized set if you own one of the three listed Benchmade models, and keep Nylatron or thin steel on hand for quiet pivots and fine tuning. Measure your pivot, match all three dimensions, and your folder will open smooth and stay centered for years.
Write Your Review
No reviews yet. Be the first to share your experience!