Key takeaways
- A dripping hot tap often needs a fresh washer, not a new faucet. Compare six washer kits by size, shape, material, and limits, and match the seal to your tap.
A hot tap that keeps dripping after you shut it wastes water and wears the valve seat. The fix is often a fresh washer in a material that copes with heat, and the best tap washers for hot water are the ones that match your tap size, shape, and water conditions. These six kits cover the common sizes, from flat to beveled.
Quick verdict
Six kits made the list, and each one suits a different job. The 116-piece Danco kit is the pick for a whole house, while the smaller Plumb Pak kits suit a single tap repair. The 101-piece Danco kit adds O-rings, and the Storehouse set adds seals for mixed jobs. Read the table, then match the kit to your tap.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| DANCO Washer and O-Ring Faucet Repair Kit, 101 Pc | Flat and beveled washers plus O-rings | Whole-house repairs | 101 pieces in assorted sizes | No stated temperature rating |
| Danco 80817 Home Washer Assortment, Rubber | Mixed faucet, hose, and slip-joint washers | General home repairs | 42 pieces in assorted sizes | Rubber hardens with heat cycling |
| Danco 10875 Washer Assortment, Rubber | Flat and beveled faucet washers | A large stock of common sizes | 116 washers; listed temperature rating of 86 to 248 | Rubber only; no silicone pieces |
| Plumb Pak PP805-21 Faucet Washer Assortment, Beveled, Brass/Rubber | Beveled washers with screws | Compression taps with angled seats | 24 washers and 4 brass screws | Beveled shape only |
| Plumb Pak PP805-20 Faucet Washer Assortment, Flat, Rubber | Flat washers with screws | Quick-opening taps | 20 washers and 4 brass screws | Flat shape only |
| STOREHOUSE 54 Piece Washer/Seal Assortment | Mixed neoprene washers, O-rings, and seals | Mixed water and irrigation jobs | 54 pieces in an organized case | Mixed set, not faucet-only |
If you only need to fix one dripping hot tap, start with the Plumb Pak PP805-20 for a flat washer or the PP805-21 for a beveled washer. Both include brass screws and cover the common trade sizes.
How we selected
We picked kits and packs from maker and listing pages we opened and read. Every product below was listed as available on the page we read, and every size, count, and material claim comes from that page. We gave weight to size range, washer shape, material, and any stated temperature rating.
Hot water is hard on washers. A faucet maker’s guide lists silicone at 12 to 15 years in home service, standard EPDM rubber at 5 to 8 years, and fiber at 3 to 5 years, and it notes that rubber hardens with hot water cycling. The same guide rates modern silicone, EPDM, and nitrile washers for hot and cold supply service up to 180 degrees Fahrenheit.
Most of the kits we could verify are rubber, and only one lists a temperature rating. That is normal here: kits are sold by size and shape, not by a hot-water label. We judged each kit on the sizes it covers, the shapes it includes, and the material the maker states.
Tap washers for hot water
These six kits and packs all contain tap washers that fit compression taps and quick-opening taps used with hot water. None of them is sold as a hot-water-only product, so the notes below call out the material, the sizes, and the limits the maker states. Bring your old washer to match size and shape before you order.
DANCO Washer and O-Ring Faucet Repair Kit, 101 Pc
This 101-piece kit is the widest net in this roundup. It pairs flat and beveled faucet washers with a full run of O-rings, so one box covers the washer and the seal behind it. It suits a home with several taps that drip at different ages and need different parts.
The kit is for a homeowner who wants one box for the whole house. The maker describes it as holding the most popular washers and O-rings in one kit, with trade sizes from 1/4R to 3/8L in flat and beveled shapes for the common compression taps.
Inside the box are 101 pieces: 1/4R, 1/4L, 3/8R, and 3/8L washers in flat and beveled forms, garden hose washers, and O-rings in sizes 5, 6, 7, 8, 9, and 11, plus an O-ring for Crane Dialese faucets. The brand is Danco and the model is 10894.
The maker does not state a temperature rating or a material grade for the washers, so there is no printed hot-water figure to lean on. The washers are rubber, and rubber hardens with repeated hot water cycling, so the hot side will wear first.
- 101 pieces cover washers and O-rings in one box
- Flat and beveled shapes in four common trade sizes
- Includes O-rings in sizes 5 through 11 for stem and spout seals
- Fits a wide range of kitchen and bathroom taps
- No stated temperature rating on the page
- Rubber only, so the hot side may wear first
- Large kit for a single-tap repair
Buy if you look after several taps and want washers and O-rings in one box.
Skip if you need one washer for one tap, or if you want a silicone washer for a hard-water hot line.
Danco 80817 Home Washer Assortment, Rubber
This 42-piece assortment is the classic home repair box. It mixes faucet washers with hose washers, slip-joint washers, O-rings, and screws, so it covers more than the tap itself. It suits a basic toolbox that handles small plumbing jobs around the house.
The kit is for a homeowner who wants a single box for common leaks. The maker states that the assortment holds the most popular and widely used washers in various sizes, and that replacing a worn washer beats replacing the whole faucet. The mix of flat and beveled washers covers the common compression tap sizes.
The box holds 42 pieces in rubber, in black and red. The faucet washers include two number 0 beveled, two number 00 beveled, two 1/4 flat, two number 0 flat, and two number 00 flat washers, plus two number 8 and two number 12 O-rings, bibb screws, a round hose washer, sink strainer washers, slip-joint washers, friction washers, tank bolt washers, cone washers, and ballcock washers. The maker notes that the small red washers are for outdoor spigots.
The maker does not state a temperature rating for this kit, and the washers are rubber, which hardens with heat cycling. Only a few pieces in the box are faucet washers, so most of the 42 pieces serve other joints.
- 42 pieces cover faucet, hose, and slip-joint washers
- Includes screws, O-rings, and strainer washers
- Flat and beveled faucet washers in common sizes
- Small red washers included for outdoor spigots
- No stated temperature rating
- Few faucet washers per size in the box
- Rubber hardens with hot water cycling
Buy if you want one box for common leaks across taps, hoses, and slip joints.
Skip if you need depth in one faucet washer size, or a washer rated for hot water by the maker.
Danco 10875 Washer Assortment, Rubber
This 116-piece kit is the largest faucet washer stock in this roundup, and the only one with a stated temperature rating. It holds flat and beveled washers across the common trade sizes, plus garden hose washers. It suits a home with many taps or a small repair business.
The kit is for someone who repairs taps often and wants depth in every size. The maker describes it as a kit of 116 of the most used washers on the market, aimed at the professional plumber or the everyday DIY individual.
The kit holds 116 washers in black rubber. Flat washers include number 00 at 1/2 in outside diameter, number 0 at 17/32 in, 3/8L at 11/16 in, 1/2 at 3/4 in, 1/2L at 25/32 in, 1/4 at 9/16 in, 1/4L at 19/32 in, 3/8 at 5/8 in, and 3/8M at 21/32 in, plus a number 00 beveled washer at 1/2 in outside diameter and two garden hose washers, one with a screen. The maker lists a temperature rating of 86 to 248 and describes the rubber as having high abrasive resistance and temperature resistance.
The page lists the temperature rating as 86 to 248 without stating the unit, so read the packaging before you rely on the figure. All 116 pieces are rubber, with no silicone or PTFE washer in the box.
- 116 washers across nine flat sizes and a beveled size
- Only kit here with a stated temperature rating
- Includes garden hose washers, one with a screen
- Covers the most used faucet washer sizes
- Temperature rating is listed without a unit
- Rubber only, with no silicone or PTFE pieces
- Large kit for a one-tap repair
Buy if you repair taps often and want depth in every common size.
Skip if you need silicone washers, or if one tap is the only job on your list.
Plumb Pak PP805-21 Faucet Washer Assortment, Beveled, Brass/Rubber
This beveled assortment is the pick for compression taps with angled seats. It holds 24 washers in assorted sizes with four brass screws, so you can fit the washer and replace a tired screw in the same job. It suits an older two-handle tap that drips from the spout.
The kit is for a compression tap where the washer presses onto an angled seat. A beveled washer matches that seat shape, and the maker lists the material as brass and rubber.
The kit includes 24 washers in assorted sizes and four brass screws. The material is listed as brass and rubber. The page lists the kit as a faucet washer assortment for sink and faucets, and the listing page listed it as available for ship to store or delivery.
The kit holds beveled washers only, so it does not suit a quick-opening tap that needs a flat washer. The maker does not state a temperature rating, and the sizes are listed as assorted rather than spelled out.
- Beveled shape suits angled compression seats
- 24 washers in assorted sizes
- Four brass screws included for the stem
- Small kit that fits a basic toolbox
- Beveled shape only
- No stated temperature rating
- Sizes listed as assorted, not spelled out
Buy if your compression tap has an angled seat and you need a beveled washer.
Skip if your tap needs a flat washer, or if you want a stated temperature rating.
Plumb Pak PP805-20 Faucet Washer Assortment, Flat, Rubber
This flat assortment is the match for quick-opening taps. It holds 20 washers in assorted sizes with four brass screws, and the flat shape gives full water flow and a firm shut-off on the taps it fits. It suits a modern two-handle tap that drips after you close it.
The kit is for a tap with a flat seat, where a flat washer is the right shape. The maker lists the material as rubber, and the assortment covers the common sizes, so you can match the old washer by size and thickness.
The kit includes 20 assorted washers and 4 screws. The material is listed as rubber. The page lists the kit as a faucet washer assortment for sink and faucets, and the listing page listed it as available for ship to store or delivery.
The kit holds flat washers only, so it does not suit a compression tap with an angled seat. The maker does not state a temperature rating, and the sizes are listed as assorted rather than spelled out.
- Flat shape suits quick-opening taps
- 20 washers in assorted sizes
- Four brass screws included for the stem
- Small kit that fits a basic toolbox
- Flat shape only
- No stated temperature rating
- Sizes listed as assorted, not spelled out
Buy if your tap has a flat seat and you need a flat washer in a common size.
Skip if your tap needs a beveled washer, or if you want a stated temperature rating.
STOREHOUSE 54 Piece Washer/Seal Assortment
This 54-piece set is the mixed box in this roundup. It holds neoprene washers, cone washers, O-rings, foam washers, poly-fiber washers, and metal washers in a PVC case with a chart. It suits a repair box that covers water, irrigation, and general sealing jobs.
The set is for a homeowner who wants one case for many small sealing jobs, not only taps. The maker describes it as a universal washer and seal set that helps stop leaks in a wide variety of water or irrigation systems.
The set holds 54 pieces: neoprene washers, cone washers, neoprene O-rings, foam washers, red poly-fiber washers, white plastic O-rings, aluminum washers, and E-style retainers. The materials are listed as poly-fiber, aluminum, copper, plastic, and neoprene. The set comes in a PVC storage case with a chart for easy identification.
This is a mixed set, so only part of the 54 pieces are faucet washers. The maker does not list faucet washer sizes or a temperature rating for the set, so matching a tap washer means checking the chart in the case.
- 54 pieces in an organized PVC case
- Neoprene washers and O-rings included
- Chart in the case helps with identification
- Covers water and irrigation sealing jobs
- Mixed set, not faucet-only
- No faucet washer sizes listed
- No stated temperature rating
Buy if you want one case for many small sealing jobs around the home.
Skip if you only need tap washers, or if you want listed faucet washer sizes.
Buying guide
A washer is a small part, but the wrong size, shape, or material will not seal. The five points below cover the choices that decide whether a new washer stops the drip or brings it back. Work through them in order, and keep the old washer until the job is done.
Choose the right size tap washer for hot water in the best tap washers for hot water
Size is the first thing to get right, and the old washer is the best guide. Measure its outside diameter and thickness, note whether it is flat or beveled, and match the new washer to those numbers. A washer that is too small will not seal, and one that is too large will not seat.
A faucet maker’s guide states that most home supply connections use a 3/8 in compression beveled washer at the shut-off valve side and a 1/2 in-14 NPSM flat washer at the faucet shank side. Inside the faucet, compression taps use trade sizes such as 00, 0, 1/4, 3/8, and 1/2, and the Danco 10875 kit lists outside diameters from 1/2 in to 25/32 in across those sizes. Bring the old washer with you, or measure it with calipers.
Flat, beveled, or cone: pick the shape
Washer shape matters as much as size. A flat washer suits a flat seat in a quick-opening tap, a beveled washer suits an angled seat in a compression tap, and a cone washer suits a hose or slip-joint connection. Fitting the wrong shape is the fastest way to a leak that will not stop.
Look at the old washer before you throw it away. A flat washer is a plain disc, a beveled washer is flat on one side and sloped on the other, and a cone washer tapers to a point. The Danco 10875 kit includes both flat and beveled washers, while the Plumb Pak PP805-20 holds flat washers only and the PP805-21 holds beveled washers only.
Rubber, neoprene, silicone, or PTFE
Material decides how long a washer lasts on a hot tap. Rubber is common and cheap, neoprene adds heat and chemical resistance, silicone lasts longest in hot water, and PTFE handles heat and minerals but needs careful fitting. Pick the material for your water, not just for the tap.
A faucet maker’s guide lists silicone at 12 to 15 years in home service, standard EPDM rubber at 5 to 8 years, and fiber at 3 to 5 years, and it notes that rubber hardens with hot water cycling. The same guide states that silicone, EPDM, and nitrile washers are rated for hot and cold supply service up to 180 degrees Fahrenheit. Most of the kits we verified are rubber, so expect to change the hot-side washer sooner than the cold-side one.
Count the washers you will actually use
A big kit looks generous, but only the pieces that fit your taps have value. Count the taps in your home, note the sizes each one needs, and compare that list with what the kit holds. A 116-piece kit suits a house full of taps, while a 20-piece kit suits a single repair.
The kits in this roundup range from 20 washers to 116 washers, and from 42 to 101 pieces when O-rings and screws are counted. A mixed kit such as the Danco 80817 holds faucet washers, hose washers, slip-joint washers, and O-rings, so it covers more jobs but fewer faucet washers per size. A faucet-only kit such as the Danco 10875 holds more of the sizes you will reach for first.
Keep spares. A faucet maker’s guide advises replacing both the hot and cold washers at the same time, since the labor is the same and the cold side often fails soon after the hot side.
Check the seat before you fit a new washer
A new washer cannot seal against a damaged seat. Before you fit the washer, look inside the tap body at the brass ring the washer presses against. A smooth seat gives a clean seal, while a scored seat will cut the washer and bring the drip back within weeks.
Shut off the water at the angle stop, open the tap to drain the line, and remove the stem. Shine a light into the body and run a fingertip over the seat. If you feel a groove or see a rough ring, the seat needs attention. Some seats unscrew and can be replaced, while others need a seat wrench or a smoothing tool.
FAQ
These are the questions that come up most often when a hot tap starts to drip. The answers below draw on the maker and listing pages we opened, plus a faucet maker’s guide to washer materials and sizing. If your tap is unusual, take the old washer and the stem with you when you shop.
Can I use the same tap washers for hot and cold water?
Yes, in most homes the same washer works on both sides. A faucet maker’s guide states that modern silicone, EPDM, and nitrile washers are rated for hot and cold supply service up to 180 degrees Fahrenheit, while home hot water tops out around 120 degrees Fahrenheit. The hot side simply wears first.
The difference is life, not fit. Heat cycling hardens rubber, so the hot-side washer often fails months before the cold-side one. When you replace one, replace both, and keep a spare of the same size in the box.
Why does the hot tap drip first?
Heat is the main reason. Every hot cycle expands the washer and the valve parts, then lets them cool and shrink, and that movement slowly hardens rubber and wears the seal. The hot side also runs more often in kitchens, which adds wear to the same washer.
A faucet maker’s guide notes that rubber hardens with hot water cycling, and that mineral scale from hard water cracks rubber as the joint flexes with temperature changes. If the hot tap drips and the cold tap does not, the washer on the hot side is the first part to check, and the seat behind it is the second.
Flat or beveled: which washer shape fits my tap?
Match the shape to the seat. A flat washer fits a flat seat in a quick-opening tap, and a beveled washer fits an angled seat in a compression tap. The old washer shows the shape, so keep it until the new one is fitted and the tap is back together again.
If the old washer is a plain disc, buy flat. If one side is sloped like a small cone, buy beveled. The Plumb Pak PP805-20 holds flat washers and the PP805-21 holds beveled washers, while the Danco 10875 kit holds both shapes.
How often should I change a hot tap washer?
There is no fixed schedule, because water and use vary. A faucet maker’s guide advises inspecting washers every 2 years and replacing them every 5 to 10 years, with silicone lasting 12 to 15 years and standard EPDM rubber lasting 5 to 8 years. Hard water and heavy use shorten those figures.
Watch for the signs instead of the calendar: a drip that continues after the tap is shut, a handle that needs extra force to stop the flow, or a washer that feels hard and cracked when you remove it.
What size washer does my tap need?
The size depends on the tap, not on the room. Measure the old washer’s outside diameter and thickness, note its shape, and match those numbers to the kit. Common trade sizes run from 00 to 1/2, with outside diameters from 1/2 in to 25/32 in in the kits we reviewed.
If the old washer is missing or crumbled, measure the stem end and the seat instead, or take the stem to the store and match it by hand.
Conclusion
The Danco 10875 kit is the strongest choice for a house with many taps, thanks to its 116 washers and a stated temperature rating. For a single tap, the Plumb Pak flat or beveled kit is enough. Match the size and shape to the old washer, favor silicone for hard water, and change both sides at once for a lasting fix.
Write Your Review
No reviews yet. Be the first to share your experience!