Updated Nov 15, 2026· 16 min read

Key takeaways

  • Six electric meat grinders for wild game compared on maker-stated game use, throughput and plate sets, from #12 models at 11 lbs per minute to a #32 at 18.

A full game season turns on output: animals arrive whole and at once, and the grinder sets the pace for every cut that follows. These meat grinders for wild game were chosen on maker-stated game use, stated throughput and stated plate sets, from 11 pounds per minute up to 18. Each figure below comes from the maker’s own page.

Quick verdict

Three of these six grinders carry the maker’s own game wording, and the other three earn their places on stated output, head size and plate sets. The MEAT! #32 states the fastest rate at up to 18 pounds per minute, while the LEM BigBite #32 pairs near-equal output with deer and elk named outright.

  • For whole-season volume with game named by the maker: LEM Products BigBite #32 Meat Grinder, at approximately 17 pounds per minute.
  • For the fastest stated output: MEAT! 1.5 HP Grinder (#32), at up to 18 pounds per minute in an all-stainless build.
  • For grinding and stuffing in one unit: Weston Pro Series #32 Electric Meat Grinder and Sausage Stuffer, with a stated plate pair at 4.5mm and 7mm.
  • For two grinds in one pass: LEM #22 Dual Grind Meat Grinder, at approximately 13 pounds per minute.
  • For maker-stated game use in a mid-size body: LEM Products BigBite #12 Meat Grinder, at up to 11 pounds per minute.
  • For hunting use stated with exact plates: VEVOR Commercial Meat Grinder, #12, 550W/0.7HP, with plates at 4.5mm and 10mm.

All six are electric, all state output in pounds per minute, and the three largest wear #32 heads.

Product Type Best for Key spec Main limit
LEM Products BigBite #32 Meat Grinder #32 electric grinder Whole-season volume Approximately 17 lbs per minute; deer and elk named by the maker Heaviest pick at 64.8 pounds
MEAT! 1.5 HP Grinder (#32) #32 electric grinder Fastest stated output Up to 18 lbs per minute; all-stainless build Plate sizes described, not stated in numbers
Weston Pro Series #32 Electric Meat Grinder and Sausage Stuffer #32 electric grinder Grinding and stuffing in one unit Plates at 4.5mm and 7mm; 12 to 18 lbs per minute One speed setting, per the maker
LEM #22 Dual Grind Meat Grinder #22 electric grinder Two grinds in one pass Approximately 13 lbs per minute; plates at 4.5mm and 10mm Output sits below the #32 class
LEM Products BigBite #12 Meat Grinder #12 electric grinder Maker-stated game use, mid-size Up to 11 lbs per minute; venison listed by the maker Plate sizes not stated in numbers
VEVOR Commercial Meat Grinder, #12, 550W/0.7HP #12 electric grinder Hunting use stated, exact plates Plates at 4.5mm and 10mm; up to 11 lbs per minute A #12 head, so big days take more loads

How we selected

Game fit here rests on printed statements, not brand reputation: a maker’s own game, deer or venison wording where a page carries it, and stated throughput, head size and plate sets everywhere. Three models carry the game wording outright; the other three post output figures in the #32 and #22 classes.

Every pick is an electric grinder, and every pick states a throughput in pounds per minute, so the figures compare directly. The floor sits at 11 pounds per minute in the #12 class, and the ceiling reaches 18 pounds per minute in the #32 class.

Plate sets carried weight beside output: a stated coarse and fine pair, or a stated stuffing plate with tubes, counted for more than a bare plate count. Makers who state plate sizes in millimeters gave the clearest ground, and the entries below say where a maker lists plates by description instead.

Build rounded out the criteria: stainless heads and augers, motors rated for continuous work, and stated weights. Brand image without a printed statement never counted.

The meat grinders for wild game, model by model

The six models below run from a pair of #12 grinders at up to 11 pounds per minute to three #32 machines built for the heaviest days of the season. Each entry sticks to what the maker states: game wording where it exists, output figures, plate sets, included parts, and the limits printed beside them.

LEM Products BigBite #32 Meat Grinder

LEM aims this #32 straight at hunters in its own words: the maker calls it perfect for serious hunters processing 6 or more deer, elk, or other game and animals per season, and lists game processing among its stated uses. Stated output runs to approximately 17 pounds of meat per minute from a 1.5 HP motor.

The fit is whole-season volume. Venison and deer both appear in the maker’s meat list, beside beef, pork, lamb and mutton, and the motor is a high-torque, permanently lubricated unit with a built-in circuit breaker, driving a stainless steel knife, head and auger. A throat opening of 3 inches takes large pieces, which shortens the knife work before grinding.

The plate set is stated in numbers: 4.5mm and 10mm stainless steel plates plus a stuffing plate, with three plastic stuffing tubes at 1/2 inch, 1 inch and 1 1/8 inch outside diameter. A storage drawer, a noise-dampened design and a meat pan round out the build, and LEM states a five-year factory warranty with lifetime customer support. The limit is mass: at 64.8 pounds, this grinder lives where it lands, on a bench or a cart.

  • Pro: Maker names deer, elk and game processing outright, the clearest game wording here
  • Pro: Approximately 17 lbs per minute with plates stated at 4.5mm and 10mm
  • Pro: Stainless steel knife, head and auger with a 3 inch throat
  • Con: At 64.8 pounds it is the heaviest model on this list
  • Con: Output trails the MEAT! #32’s stated figure by a small margin

Buy if your season runs to several animals and you want the maker’s deer and elk wording behind the largest LEM. Skip if it must move between kitchen and garage each session, or if your harvest fits a #12’s pace.

MEAT! 1.5 HP Grinder (#32)

MEAT! gives this #32 the highest stated output on the list: its 1.5 HP motor generates up to 18 pounds of ground meat per minute, in the maker’s words. The build is all stainless steel, heavy-duty down to the last spring and bolt per the maker, with coarse and fine plates plus a stuffing plate in the box.

For hunters whose bottleneck is grinding speed, this is the headline pick: the stated figure edges past the LEM #32, and the all-stainless construction covers head and body. Three stuffing tubes come with the stainless stuffing plate for sausage work, and a filter guard sits over the loading chute. The maker’s copy doubts any crew can keep up with the machine.

The spec sheet runs thinner than the LEM’s in two places. Plate sizes arrive as descriptions, coarse and fine, rather than millimeter figures, so texture planning leans on habit instead of numbers. The maker states no weight on its product page, which leaves bench planning to the buyer. Neither gap touches the output claim.

  • Pro: Highest stated output here, up to 18 lbs of ground meat per minute
  • Pro: All-stainless build, including the stuffing plate
  • Pro: Coarse and fine plates plus three stuffing tubes included
  • Con: Plate sizes described as coarse and fine, not stated in millimeters
  • Con: Maker states no unit weight on its product page

Buy if stated pace matters most and your crew processes in long, fast runs. Skip if you plan textures by millimeter plate sizes, or if a stated weight matters for your bench or cart.

Weston Pro Series #32 Electric Meat Grinder and Sausage Stuffer

Weston’s Pro Series #32 pairs a 2 HP, 1500 watt motor with precision-engineered steel gears and a stated grind rate of 12 to 18 pounds of meat per minute. Its plate pair is stated in numbers, a coarse 7mm and a fine 4.5mm in stainless steel, and the head uses a rifled design with a tapered throat.

The fit is the workstation: this unit grinds and stuffs in one body, with a sausage stuffer kit that includes an adapter spacer and four funnels. A patented auger-grabbing stomper feeds the auger, a patented storage tray with a cover holds pieces and parts, and a built-in knife sharpener keeps the knife ready. For a hunter who grinds and stuffs from the same bench, the kit covers both jobs.

The motor is air cooled and permanently lubricated, and the spec sheet lists one speed setting, which is the model’s limit: pace control comes from feeding, not from gears. The coarse plate at 7mm sits finer than the 10mm coarse plates on the LEM and VEVOR picks, so the coarsest chili grind runs finer here. Within those lines, it is the most complete single-unit station on the list.

  • Pro: Stated 12 to 18 lbs per minute with steel gears and a rifled head
  • Pro: Plate pair stated at 7mm coarse and 4.5mm fine
  • Pro: Full sausage stuffer kit with four funnels, plus a built-in knife sharpener
  • Con: One speed setting only, per the maker
  • Con: Coarsest plate at 7mm runs finer than the 10mm coarse plates elsewhere here

Buy if grinding and stuffing share one bench and one session, and you want both kits in a single #32 body. Skip if you lean on a true 10mm coarse grind for chili meat, or if multiple speeds matter to your feeding style.

LEM #22 Dual Grind Meat Grinder

This #22 does two grinds in one pass: a double-edged knife works with two plates, so meat takes a first and second grind in a single run through the head. LEM states approximately 13 pounds per minute from a 1.0 HP, 750 watt motor, through a stainless steel head with a 3 inch opening.

The fit is the double-grind workflow. Burger meat takes two runs, coarse then fine, and this head folds both into one, which halves the handling on the batches of a game season. Four stainless steel plates come in the box: a first grind plate, a 4.5mm plate, a 10mm plate and a stuffing plate, with three plastic stuffing tubes at 5/8 inch, 1 inch and 1 3/8 inch outside diameter.

The meat pan measures 16-1/2 by 12-1/8 by 3 inches deep and carries a guard, the unit weighs 49.6 pounds, and the spec sheet lists a five-year warranty, ETL certification and a 6 foot cord. The limits are class limits: output at approximately 13 pounds per minute sits below the #32 trio, and the one-pass texture is set by its plate pair, not by a second run.

  • Pro: Two grinds in one pass, a design no other pick here states
  • Pro: Plates stated at 4.5mm and 10mm, plus first grind and stuffing plates
  • Pro: Guarded meat pan and a stated five-year warranty
  • Con: Output at approximately 13 lbs per minute trails the #32 class
  • Con: One-pass texture is fixed by the plate pair, with no mid-batch adjustment

Buy if most of your game meat takes a double grind and you want it done in a single pass. Skip if your season’s volume points to a #32, or if you prefer to run each grind separately and adjust between runs.

LEM Products BigBite #12 Meat Grinder

LEM states the game fit for this #12 in plain words: the maker calls it ideal for processing game if you are a hunter, chef, or buying bulk meat, and lists venison among the meats it handles. Stated output runs up to 11 pounds of meat per minute from a 0.75 HP motor in a stainless steel build.

For a hunter processing an animal or two at a time, this is the balanced pick: a stainless steel knife, head and auger, a meat pan the listing rates at 7 lb capacity, and a storage drawer for the plates and tubes. The motor is permanently lubricated and the design is noise-dampened, and at 33.1 pounds the unit moves between counter and cupboard without help.

In the box sit a coarse plate, a fine plate and a stuffing plate, three stuffing tubes and a plastic meat stomper. The maker’s listing does not state the plate sizes in millimeters, and the #12 head sets the pace ceiling: multi-animal days run slower here than on any #32. For single-animal sessions, the maker’s game wording and the mid-size body line up well.

  • Pro: Maker states game processing and lists venison outright
  • Pro: Stainless steel knife, head and auger at 33.1 pounds
  • Pro: Storage drawer and a noise-dampened, permanently lubricated motor
  • Con: Plate sizes are not stated in numbers on the maker’s listing
  • Con: The #12 head caps pace for multi-animal days

Buy if your season is one or two animals at a time and you want the maker’s game wording in a movable mid-size grinder. Skip if you plan plates by the millimeter, or if your processing days stack several animals back to back.

VEVOR Commercial Meat Grinder, #12, 550W/0.7HP

VEVOR lists hunting meat processing among this #12 grinder’s stated uses and names venison among the meats it handles, which puts the game fit in the maker’s own words. Stated output runs up to 11 pounds of meat per minute, with plates stated exactly at 10mm coarse and 4.5mm fine, plus a stuffing plate.

The build is commercial: a 550W, 0.7 HP motor, a three-stage auger and a cross-sharp steel blade in a stainless steel housing, with two cross blades in the box. Three sausage stuffing tubes come sized at 0.47 inch (12mm), 0.87 inch (22mm) and 1.2 inch (30mm), and the unit carries ETL approval, rapid cold-air cooling, a reset button for overload protection and anti-vibration foot pads.

Against the LEM #12: both state up to 11 pounds per minute and both name game use, but VEVOR states its plate and tube sizes to the millimeter while LEM offers a storage drawer and a stated pan capacity. The class limit is shared: a #12 head asks for more loads across a big day than a #32. For size-led planning, this is the fuller #12 spec sheet.

  • Pro: Maker states hunting meat processing and lists venison
  • Pro: Plates and tubes all stated in exact sizes
  • Pro: ETL approval, cold-air cooling and overload reset on a commercial build
  • Con: A #12 head, so large days take more loads than the #32 picks
  • Con: Commercial styling suits a work bench more than a home counter

Buy if you want stated hunting use with every plate and tube size printed, in a commercial #12 build. Skip if your season’s volume belongs on a #32, or if a storage drawer and home styling matter more than stated sizes.

Buying guide

A game grinder purchase turns on three stated facts: the output figure, the plate set and the head size. Read those three lines on any maker’s page first, and let the season you actually hunt, not the largest season you can imagine, set the size of the machine you bring home.

Throughput sets the pace of processing day

Stated output runs from up to 11 pounds per minute in the #12 class to up to 18 in the MEAT! #32, and the gap compounds across a whole animal. At the #12 pace, grinding stays a steady, load-by-load job; at the #32 pace, the bottleneck moves to the cutting board, where trimming and cubing set the rhythm instead.

Read each figure as the maker’s claim under steady feeding, and match it to the largest day you face. A grinder bought for one deer a year sits oversized, while one bought for a full camp’s harvest earns its bench space.

Matching meat grinders for wild game to the harvest

Head size is the simplest sizing rule on this list: #12 for an animal or two at a time, #22 for regular double-grind work, and #32 for multi-animal days and shared harvests. Weight follows head size, from 33.1 pounds on the LEM #12 to 64.8 pounds on the LEM #32, and that gap decides where the machine lives.

Throat size matters beside head size. The LEM #32 and the Dual Grind #22 both state a 3 inch opening, which takes larger pieces and trims knife time before the grind. A smaller throat asks for smaller cubes, and across a whole animal that prep difference adds up.

Plate pairs cover burger and sausage work

Across these picks, the stated pattern repeats: a 10mm plate for coarse work and a 4.5mm plate for fine work, on the LEM #32, the Dual Grind #22 and the VEVOR #12 alike. Coarse plates feed chili meat and the first grind of a two-pass batch, while fine plates finish burgers and sausage blends.

Weston breaks the pattern slightly with a 7mm coarse plate beside its 4.5mm fine plate, a pairing that leans toward burger textures. Where a maker describes plates as coarse and fine without numbers, as MEAT! does, the pairing still covers both jobs; the buyer plans texture by habit rather than by millimeter.

One pass or two: dual grind heads and second runs

Most grinders take texture in runs: a coarse pass, then a fine pass for burger meat. The Dual Grind #22 folds both runs into one pass with a double-edged knife and two plates, which cuts the handling on exactly the batches game cooks repeat most, with the texture set by the plate pair.

Separate runs keep one advantage: the operator can season or adjust between passes, and can stop at the coarse stage for part of a batch. The workflow choice shapes processing day as much as the headline figure does.

Weight, storage and cleanup after long runs

Game grinders earn their keep in a few heavy weeks and sit stored for the rest of the year, so storage belongs in the purchase call. Drawers in the LEM bodies and Weston’s covered storage tray keep plates, knives and tubes with the machine, which matters when the first animal of the season arrives on short notice.

Cleanup follows: stainless heads, knives and augers take repeated washing, and a unit light enough to reach the sink, like the 33.1 pound LEM #12, cleans faster than a 64.8 pound bench fixture wiped down in place.

FAQ

Most questions about game grinders come back to stated output, stated plates and which makers print the word game at all. The answers below stay inside those printed lines, model by model, so the figures quoted here match the figures in the entries above them.

How much throughput do meat grinders for wild game need?

Match the stated figure to the largest day you face. Up to 11 pounds per minute in the #12 class covers an animal or two at a steady pace, approximately 13 in the #22 suits regular double-grind work, and 17 to 18 in the #32 class keeps a full crew busy through multi-animal days.

The stated figure assumes steady feeding of prepared pieces. Trimming, cubing and packing run at hand pace, so past a point the grinder waits on the crew more than the crew waits on it.

Which models carry the maker’s own game wording?

Three do. LEM calls the BigBite #32 perfect for serious hunters processing 6 or more deer, elk, or other game per season and lists game processing among its uses; LEM calls the BigBite #12 ideal for processing game and lists venison; VEVOR lists hunting meat processing among its stated uses.

The other three, the MEAT! #32, the Weston Pro Series #32 and the LEM Dual Grind #22, earn their places on stated output, head class and plate sets. Their makers print no game wording on their pages, and their entries above claim none.

Is a #12 grinder enough for deer season?

For one or two animals at a time, yes: both #12 picks state up to 11 pounds per minute, which moves a single animal through in steady loads, and both carry game wording from their makers. The LEM #12 adds a storage drawer, and the VEVOR adds fully stated plate and tube sizes.

The #12 case weakens as the day stacks up. Several animals back to back turn the smaller head into the bottleneck, the workload the #32 class, at 17 to 18 stated pounds per minute, exists to absorb.

What plates do the picks use for burgers and sausage?

The stated pattern is a 10mm coarse plate and a 4.5mm fine plate, printed by LEM for the #32 and the Dual Grind #22 and by VEVOR for its #12. Fine plates finish burger blends, coarse plates start chili meat and first grinds, and every pick here adds a stuffing plate for sausage work.

Weston varies the pair with a 7mm coarse plate beside the 4.5mm fine, and MEAT! describes its plates as coarse and fine without numbers. Tube sizes, where stated, run from 1/2 inch to 1 3/8 inch outside diameter across the LEM models.

Do these grinders stuff sausage as well?

Yes, every pick lists stuffing gear. The LEM models pair a stuffing plate with three tubes each, the VEVOR lists three sized tubes at 12mm, 22mm and 30mm, the MEAT! includes a stainless stuffing plate with three tubes, and the Weston carries a full stuffer kit with an adapter spacer and four funnels.

The Weston kit runs deepest, with the funnel count stated at four. Buyers who stuff often will weigh that kit against the LEM #32’s output and the Dual Grind’s one-pass texture.

Conclusion

Season volume decides this list: the LEM BigBite #32 carries the maker’s own deer and elk wording, the MEAT! #32 the highest stated output, and the #12 pair the lightest bodies for smaller harvests. Match stated throughput and plate sets to your season, and the grinder keeps pace with the crew through the last animal of the day.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.