Key takeaways
- Meat grinders for high volume at home compared on stated motor power, pounds per minute, head size, gear drives, plate sets and the full sausage stuffing gear.
Grinding stops being a small chore when the batch is a whole deer, a side of pork or a freezer-filling run of burger blend. The meat grinders for high volume at home in this roundup state outputs from 11 to 14 pounds a minute, run #12 and #22 heads, and drive their augers with steel gearing built for long sessions.
Quick verdict
The Weston Pro Series #22 is the pace setter of this group, with a 1.5 HP motor and a stated 14 pounds per minute, plus a forward and reverse drive. The LEM Big Bite #22 counters with all steel gears, roller bearings and a stated average of 13 pounds per minute, and the LEM Big Bite #12 brings the same design down to a lighter 33 pound machine.
The VEVOR #22 matches the LEM #22 on stated output at up to 13 pounds per minute and adds a long accessory list, while the MEAT! 1 HP Dual Grind skips the second pass entirely by grinding through two plates in one run. Every model here runs on 120 volt household current, so none of them asks for special wiring in the room where the work happens.
| Model | Motor | Stated output | Head size | Weight |
|---|---|---|---|---|
| Weston Pro Series #22 (10-2201-W) | 1.5 HP, 1120 watts | 14 lb per minute | #22 | 58 lb |
| LEM Big Bite 17811 | 1 HP, 750 watts | Average 13 lb per minute | #22 | 65 lb |
| LEM Big Bite #12 (LEM-17801) | 0.75 HP | About 11 lb per minute | #12 | 33.07 lb |
| VEVOR Commercial Meat Grinder | 750 watts, 1 HP | Up to 13 lb per minute | #22 | Not stated |
| MEAT! 1 HP Dual Grind Grinder | 1 HP | Not stated | #22 | Not stated |
How we selected
Selection started with stated throughput: each model here prints a pounds-per-minute figure, a dual grind design that removes a pass, or both. Motor power had to be printed too, in horsepower or watts, and the drive had to be described in metal terms rather than left vague or built around plastic gearing.
Home use set the second filter. All five machines run on standard household voltage, and all five sit in the weight band a household can plausibly bench, cart or store, from 33 pounds to 65 pounds where the maker states a weight. Stuffing gear mattered as well, because high volume at home usually ends in sausage: four of the five include tubes or funnels in the box, and the fifth is built around a two-plate throat made for grinding and stuffing days alike.
- A printed grinding rate, or a dual grind design that removes the second pass
- Stated motor power in horsepower or watts
- Steel gearing or a steel blade and auger train in the maker’s wording
- 120 volt household power, no special wiring
- Stuffing tubes, funnels or horns included for sausage work
Meat grinders for high volume at home, model by model
The five models split into two #22 LEM and Weston machines that lead on stated pace, a smaller #12 that keeps most of the same design, a value-built #22 with a long parts list, and a dual grind machine that trades a printed rate for a shorter process. Read them in that order.
Weston Pro Series #22 Electric Meat Grinder and Sausage Stuffer
Weston rates the Pro Series #22, model 10-2201-W, with a 1.5 HP, 1120 watt motor that is air cooled and permanently lubricated, and states a grinding pace of 14 pounds per minute. A rifled-head design and a tapered throat move meat toward the knife, and precision engineered steel gears carry the load.
The forward-reverse mode earns its place on big days: Weston describes it as useful for grinding tougher meats and meats with connective tissue, and a quarter turn of reverse clears a wad of sinew that would otherwise stop the session for a teardown. The plate set is stainless steel, coarse 7 mm and fine 4.5 mm, with a grinder knife, and the sausage stuffer kit adds an adapter spacer and four funnels, listed at 10, 20, 30 and 40 mm in the maker’s description.
A patented auger-grabbing stomper and a patented storage tray with cover handle the feeding and staging work, and a built-in knife sharpener keeps the knife edge serviceable mid-season. Weston lists the machine at 58 pounds and 24.75 by 15.5 by 17 inches, in stainless steel, with a limited five year manufacturer warranty. For a household whose volume comes in a few very large days each year, this is the most complete stated package in the group.
LEM Big Bite Meat Grinder 17811 (#22 Head)
The LEM Big Bite 17811 runs a 1 HP high torque motor rated at 750 watts and states an average grinding rate of 13 pounds per minute through its #22 head. The throat is offset for in-feed and measures 3 inches across and 7.375 inches deep, and the headstock is rifled to ease the second grind and stuffing work.
The gear drive uses all steel gears with roller bearings, and a built-in circuit breaker protects the motor from overload damage. LEM builds the headstock, screw, grinder plates, blade and meat tray from stainless steel, and the rounded meat pan carries a hand guard. The box includes stainless plates in 3/16 inch and 3/8 inch sizes, a kidney plate, a stainless knife, stuffer tubes of 5/8 inch, 1 inch and 1-3/8 inch, and a heavy duty meat stomper.
The maker lists 65 pounds, dimensions of 12 by 22.5 by 19 inches, a 6 foot cord, and a tray of 16.5 by 12.1 by 3.75 inches. Power draw is 10 amps at 120 volts. LEM lists ETL-Sanitary certification to NSF standards and a five year warranty, a smooth start feature, and no reverse. A front storage drawer keeps plates and tubes in the housing. It is the methodical pick: nothing about the stated design chases a headline number, and everything about it suits repeated heavy days.
LEM Big Bite #12 (LEM-17801)
The Big Bite #12 shrinks the same LEM formula to a 0.75 HP motor and a #12 stainless head, with a stated grind rate of about 11 pounds per minute. The maker lists the head opening at 2 inches, a weight of 33.07 pounds and dimensions of 20.24 by 9.13 by 15.98 inches, so it stores and moves like a countertop appliance rather than a bench fixture.
Three stainless plates come in the box, 4.5 mm, 10 mm and a stuffing plate, with a stainless knife and three plastic stuffing tubes of 5/8 inch, 1 inch and 1 3/8 inch outside diameter. A storage drawer sits in the housing, the on/off switch wears a sanitary cover, and the cord runs 6 feet. LEM lists ETL and ETL sanitary certification conforming to UL standards, and a five year warranty.
Eleven pounds a minute is a strong stated figure for a #12 head, and it changes what a smaller machine can do: a 60 pound batch is under six minutes of grinding time at the stated rate, before cutting and packing are counted. The trade against the #22 models is throat room, since narrower cubes are the trade for the smaller head opening. For households whose big days are one deer or one pork shoulder at a time, that trade is usually worth making.
VEVOR Commercial Meat Grinder, #22
The VEVOR #22 pairs a 750 watt, 1 HP motor with a stated capacity of up to 13 pounds of meat per minute, using a 3-stage auger and a cross-sharp steel blade. The housing is stainless steel, the listing states ETL approval, and a cold-air cooling system with a reset button for overload protection supports longer runs.
The accessory count is the longest in this group: two cross blades with one pre-installed, a 10 mm coarse plate pre-installed, a 4.5 mm fine plate, a stuffing plate, three sausage stuffing tubes at 12 mm, 22 mm and 30 mm, plus a cleaning brush, two meat claws, a meat pusher and a stuffing tube connector. Anti-vibration foot pads steady the machine on the counter. The listing states that the blades, grinding plates, stuffing tubes, grinding head, auger and meat pan can be cleaned in a dishwasher, while the main body is not immersed or rinsed.
One listing claim needs care: the maker states the machine grinds chicken cartilage and chicken bones along with fresh and frozen meat. That is the maker’s wording, and bone grinding is hard on plates and knives in any machine, so a buyer who wants that duty should expect faster wear on the cutting set. The listing does not state a weight, dimensions or a warranty length, which leaves this model as the pace-and-parts pick rather than the long-paper-trail pick.
MEAT! 1 HP Dual Grind Grinder (#22)
The MEAT! 1 HP Dual Grind takes the second pass out of a fine grind: a stainless steel first grinding plate and a choice of coarse or fine secondary plate sit in the same #22 throat, so meat reaches its final texture in one run through the machine. The maker states 1 horsepower and describes the result as coarse or fine in a single pass.
Stuffing horns come with the grinder, along with an accessory tray for organizing plates and parts during a session and a carrying handle for moving the machine between bench and storage. The maker also pairs this model with its foot pedal switch, sold separately, which lets the operator start and stop the auger with both hands on the casing during stuffing.
The maker’s page keeps the rest of the spec sheet short: no wattage, no pounds-per-minute rate, no weight and no warranty length are stated, so this model cannot be ranked on figures the way the others can. What it offers instead is a process advantage that matters on sausage days, when the second pass is pure handling time. Buyers who grind coarse for chili will gain less from it; buyers who grind fine for sausage gain the most.
Buying guide
Stated pace is the headline, but the working differences between these five machines sit in the details: how the rate was framed, how much throat room the head allows, what arrives for stuffing, and how the drive handles a jam. The sections below work through those points in the order a buyer meets them.
Average rates, ceilings and missing numbers
The wording around a grinding rate shows how to read it. An average, like the 13 pounds per minute LEM states for the Big Bite #22, is a planning number. A ceiling, like the up to 13 pounds per minute on the VEVOR listing, is a best case. A plain figure, like Weston’s 14 pounds per minute, sits between the two and still assumes steady feeding.
A missing number is information too. The MEAT! Dual Grind states no rate at all, and its case rests on removing the second pass rather than on raw pace. When comparing across brands, convert everything to batch time: at the stated rates here, 100 pounds of meat takes roughly seven to nine minutes of grinding, and the real session is always longer once cutting, seasoning, mixing and packing join the clock.
Throat room and cube size
The #22 head on three of these machines pairs with throats around 3 inches across, and the LEM #22 adds a stated throat depth of 7.375 inches, which lets long strips feed in a steady column. The #12 LEM lists a 2 inch head opening, so its cubes and strips must be cut narrower before they reach the auger.
That prep difference is the hidden trade of a smaller head. On a 20 pound batch it is a few extra minutes with a knife; on a 120 pound day it is a meaningful share of the work, and it falls on the same person who feeds the machine. Rifled headstocks, stated by both LEM and Weston on their #22 models, help the second grind and stuffing by gripping the meat column instead of letting it spin.
Plates and tubes on meat grinders for high volume at home
Plate sets in this group cover the standard working range: coarse plates near 10 mm or 3/8 inch for chili grind and first passes, fine plates at 4.5 mm for burger and sausage textures, and stuffing plates that pass seasoned meat into casings without cutting it. Every model here includes at least a coarse and a fine option.
Tube and funnel sizes decide which casings the machine fills comfortably. The LEM sets run 5/8 inch, 1 inch and 1-3/8 inch, covering snack sticks through large fibrous casings. Weston’s four funnels run from 10 mm to 40 mm. The VEVOR tubes run 12 mm, 22 mm and 30 mm. A household that makes mostly breakfast links and snack sticks should weight the narrow end of the set; a household filling summer sausage should weight the wide end.
Reverse, breakers and clearing a jam
Long sessions meet sinew, and the stated defenses differ. Weston’s forward-reverse mode is the active answer: reverse backs the auger off a tough wad so it can be re-fed in smaller pieces. The LEM #22 relies on a built-in circuit breaker that cuts power on overload, and its maker lists no reverse, so clearing means stopping and opening the head.
The VEVOR listing states a reset button for overload protection, which is the same philosophy as a breaker: stop the motor before the strain damages it. None of these features replaces trimming. Silver skin and heavy sinew removed at the cutting table never reach the plate, and the fastest stated rate in this group will not survive a throat full of untrimmed shank meat.
Weight and where the machine lives
Stated weights run from 33.07 pounds for the LEM #12 to 65 pounds for the LEM #22, with the Weston at 58 pounds. The lighter machine can ride a cart or come out of a cabinet; the two heavier ones want a bench spot of their own, with the tray dimensions, up to 16.5 by 12.1 inches on the LEM #22, counted into the footprint.
Storage design softens the weight question. Both LEM models keep their plates and tubes in a drawer in the housing, and the Weston keeps its kit under a covered storage tray, so the parts that get lost in a drawer elsewhere stay with the machine. The MEAT! adds a carrying handle and an accessory tray. Measure the storage spot with the tray and handle included, not just the body, before deciding where a machine this size will live.
FAQ
Buyers comparing machines in this class usually ask about batch size, session length, stuffing and upkeep. The answers below use only the figures and features the makers state for these five models, and they flag the places where a maker leaves a number unstated rather than filling the gap.
How much meat can meat grinders for high volume at home handle?
At the stated rates, a single session is measured in hundreds of pounds: the Weston #22 at 14 pounds per minute covers 100 pounds in about seven minutes of grinding, and the LEM #12, the slowest stated rate here at about 11 pounds per minute, covers the same batch in about nine minutes of grinding time.
The honest limit is rarely the motor. It is the cutting table ahead of the machine and the packing work behind it, plus keeping meat cold across a long session. Working in sub-batches, grinding one tray load while the next chills, keeps texture firm and the pace steady. For planning a season, think in terms of animals per day rather than pounds per minute: each of these machines can keep up with a household processing day; the crew is the bottleneck.
Can these grinders run for a full processing day?
The stated designs point that way: Weston’s motor is air cooled and permanently lubricated for continuous grinding of large volumes, the VEVOR lists a cold-air cooling system for long-term continuous working, and both LEM models protect their motors with circuit-level overload protection rather than relying on the operator to stop.
Heat still builds in the head and plate during very long runs, and warm meat smears instead of cutting cleanly, so the practical rhythm is to grind in waves and let the meat, more than the machine, set the pauses. Chilling the head parts before a big session and returning cubed meat to the cold between trays keeps the texture the plates are meant to produce.
Which of these is best for sausage making?
For grind-then-stuff work, the Weston #22 brings the widest stated stuffing kit: an adapter spacer and four funnels from 10 mm to 40 mm, plus a stuffing-friendly forward-reverse drive. The LEM models bring three tube sizes each and a kidney or stuffing plate, and the LEM #22’s rifled headstock is stated to ease stuffing as well as second grinding.
The MEAT! Dual Grind makes its case on time: one pass to final texture means the meat is seasoned and stuffed sooner, and its maker pairs it with a foot pedal switch for hands-free auger control during stuffing. The VEVOR includes three tubes and a stuffing plate. Any of the five covers standard casings; the choice turns on whether the household stuffs as a separate step or as the main event.
What maintenance do steel gear drives need?
The makers’ stated designs aim at low upkeep: Weston describes its motor as permanently lubricated, and LEM’s roller bearing gear drive runs behind a sealed housing with a storage drawer for the cutting parts. Neither maker publishes a lubrication schedule on the pages behind this roundup, so there is no stated interval to quote.
The regular work is in the cutting set, not the gearbox. Knives and plates wear as a matched pair, plates are reversible on the LEM design, and a dull knife shows up as smeared texture and slower feeding long before it stops the machine. Washing and fully drying the head, plates and knife after each session, then storing them in the drawer or tray the maker provides, is the upkeep rhythm these designs assume.
Do I need a #22 head, or is a #12 enough?
A #12 head is enough for most home volume: the LEM Big Bite #12 states about 11 pounds per minute, which clears a deer or a pork shoulder batch in minutes. The #22 head earns its size when batches regularly pass 100 pounds, when wide throats and bigger cubes cut real prep time, or when a second grind is part of every session.
Size also follows the household through storage and handling. The #12 LEM weighs 33.07 pounds and fits a cabinet; the #22 machines weigh 58 and 65 pounds and suit a bench. Buy the head size that matches the biggest day of the year only if that day comes more than once or twice; otherwise the smaller machine’s easier handling wins the other fifty weeks.
Conclusion
The Weston Pro Series #22 leads this group on stated pace and stuffing gear, while the LEM Big Bite #22 is the steady steel-gear alternative and the LEM #12 its lighter sibling. The VEVOR adds parts and pace, and the MEAT! Dual Grind saves a full pass on fine grinds. All five run on standard household current.