Updated Nov 15, 2026· 14 min read

Key takeaways

  • High end meat grinders for high volume at home compared on stated motor power, pounds per minute, steel gear drives, plate sets, head sizes and stuffing kits.

A hunting season harvest or a whole animal purchase turns grinding into a production job, and high end meat grinders for high volume at home are built for exactly that work: stated outputs from 12 to 30 pounds a minute, all-steel gear drives and #22 or #32 heads that keep pace with very large batches.

Quick verdict

The LEM Big Bite #32 is the balanced pick for most heavy home use: a 1.5 HP motor, a stated average of 17 pounds per minute, all steel gears and a 120 volt plug. The Weston Pro Series #32 adds a 2 HP motor and a built-in knife sharpener, while the Pro-Cut KG-22-XP-SS is the output leader at a stated 30 pounds per minute on the first grind.

The MEAT! 1.5 HP Commercial Grinder keeps the spec sheet short and the build all stainless, with a stated rate of up to 18 pounds per minute. The LEM #22 Dual Grind takes a different route to speed: two plates in a single pass, so coarse and fine textures come out of one run. All five machines use metal gear drives, and all five are heavy enough that a fixed spot on the bench matters.

Model Motor Stated output Head size Weight
LEM Big Bite Meat Grinder 17821 1.5 HP, 1100 watts Average 17 lb per minute #32 75 lb
Weston Pro Series #32 (10-3201-W) 2 HP, 1500 watts 12 to 18 lb per minute #32 Not stated
MEAT! 1.5 HP Commercial Grinder 1.5 HP Up to 18 lb per minute #32 Not stated
LEM #22 Dual Grind (LEM-1786) 1.0 HP, 750 watts 13 lb per minute #22 49.6 lb
Pro-Cut KG-22-XP-SS 2 HP, 220 volts 30 lb per minute, first grind #22 140 lb

How we selected

Every model here earned its place on stated facts: motor power in horsepower or watts, a printed grinding rate in pounds per minute, and wording about metal gears or stainless construction. Machines that hid their output figures, or that drove the auger with plastic gearing, did not make this list.

Head size mattered as well. A #32 head moves more meat per turn of the auger than a #22, and a #22 more than the smaller sizes found on light countertop models, so this list stays with the two largest common sizes. Voltage was the last filter: four of the five run on household current, and the one 220 volt machine is flagged clearly, because a grinder that needs a different outlet changes the whole setup.

  • Stated motor power and a printed pounds-per-minute rate
  • Steel gears or an oil bath gearbox, never plastic drive parts
  • #22 or #32 grinding head with a wide throat
  • Stainless head, auger, plates and knife in the maker’s wording
  • A stuffing kit in the box for sausage work after grinding

High end meat grinders for high volume at home, model by model

Read the five models in order of how a big processing day unfolds: the two #32 machines for the largest batches, the all-stainless MEAT! unit, the dual grind LEM that skips the second pass, and the Pro-Cut that outruns everything else here on the maker’s own figures.

LEM Big Bite Meat Grinder 17821 (#32 Head)

The LEM Big Bite 17821 pairs a 1.5 HP high torque motor with a #32 head and a stated average grinding rate of 17 pounds per minute. The gear drive uses all steel gears with roller bearings, the throat is offset and measures 3 inches across, and the motor runs on 120 volts at 1100 watts and 13 amps.

LEM builds the headstock, screw, grinder plates, blade and meat tray from stainless steel, and the rounded meat pan carries a hand guard. The box includes stainless plates in 3/16 inch and 3/8 inch sizes plus a kidney plate, a stainless knife, and stuffer tubes of 5/8 inch, 1 inch and 1-3/8 inch. A storage drawer in the front of the housing keeps the small parts with the machine, and a built-in circuit breaker guards the motor against overload.

The maker lists the unit at 75 pounds with dimensions of 12 by 24 by 19 inches, and the tray measures 16.5 by 12.1 by 3.75 inches, so a full pan of cubed meat feeds in without constant refilling. LEM lists ETL-Sanitary certification to NSF standards and a five year warranty. The drive is not reversible, and the maker lists a smooth start feature. For a household that processes several animals a season, this is the most complete package on the list.

Weston Pro Series #32 Electric Meat Grinder and Sausage Stuffer

Weston’s Pro Series #32 runs a 2 HP, 1500 watt motor that the maker describes as air cooled and permanently lubricated, with precision-engineered steel gears. Weston states a grinding range of 12 to 18 pounds of meat per minute, helped by a rifled-head design and a tapered throat that move meat toward the knife.

The included plate set is stainless steel in coarse 7 mm and fine 4.5 mm sizes, with a grinder knife, and the sausage stuffer kit adds an adapter spacer and four funnels. A patented auger-grabbing stomper design feeds the throat, and the patented storage tray with cover keeps the working surface organized while a batch is staged. A built-in knife sharpener sits in the housing, which matters on long days when a knife edge fades halfway through a second grind.

The drive runs at a single speed, so pacing comes from how steadily meat is fed rather than from a speed control. Weston positions this model, number 10-3201-W, as its largest Pro Series grinder, and the 2 HP rating is the highest horsepower figure among the 120 volt machines in this roundup. Households that grind and stuff in the same session get the most from the funnel set and the sharpener.

MEAT! 1.5 HP Commercial Grinder (#32)

The MEAT! 1.5 HP Commercial Grinder keeps its published spec sheet short: a 1.5 HP motor, a #32 head, and a stated rate of up to 18 pounds of ground meat per minute. The maker describes the construction as all stainless, and the model sits in the maker’s own grinder line alongside its smaller #22 machines.

That short spec sheet cuts both ways. The two headline figures, horsepower and output, match or beat most of this list, and all-stainless construction is the wording buyers look for in the head and body of a heavy grinder. What the maker does not publish on the product page is the supporting detail found elsewhere here: no plate sizes, no gear description, no weight and no warranty length are stated, so a buyer comparing small print will find less of it from this brand.

As a result, this model suits a buyer who shops on the two numbers that decide a processing day, motor power and pounds per minute, and who is comfortable with a plain spec sheet. The #32 head size matches the two leaders in this roundup, so tray and plate accessories in that size class apply. Treat the 18 pounds per minute as the maker’s stated ceiling, since the wording is “up to,” and plan batch timing with some margin.

LEM #22 Dual Grind Meat Grinder (LEM-1786)

The LEM Dual Grind takes a #22 head and a 1.0 HP, 750 watt motor and makes its speed in a different way: a double-edged knife works with two plates in a single pass, so meat comes out at the second plate’s texture without a separate second run. LEM states 13 pounds per minute, a 3 inch head opening and a weight of 49.6 pounds.

Four stainless plates come in the box: a first grind plate, a 4.5 mm plate, a 10 mm plate and a stuffing plate, along with a stainless dual blade knife and three stuffing tubes of 5/8 inch, 1 inch and 1-3/8 inch outside diameter. The meat pan measures 16-1/2 by 12-1/8 by 3 inches deep and carries a hand guard, and the housing adds a storage drawer and an on/off switch under a sanitary cover, with a 6 foot cord.

LEM lists ETL and ETL sanitary certification for this model, conforming to UL standards, and a five year warranty. At just under 50 pounds it is the lightest machine in this roundup by a wide margin, which makes it the one a household can still move to a cart or a lower shelf between seasons. The trade is head size: a #22 throat takes smaller cubes than the #32 machines, so knife work before grinding takes a little longer.

Pro-Cut KG-22-XP-SS Meat Grinder

The Pro-Cut KG-22-XP-SS is the output leader here by the maker’s own figures: 30 pounds per minute on the first grind through a 3/8 inch plate and 16 pounds per minute on the second grind through a 1/8 inch plate, with the meat at 32 degrees. A 2 HP high torque motor drives a #22 head through an oil bath gearbox with all steel gears.

Pro-Cut rates the machine at a 100 percent duty cycle and calls the design washerless and maintenance-free in the gearbox. The throat opens 5.5 by 6.5 inches at the top and funnels down to a 3 by 4 inch auger inlet behind a three-hole guard. The box includes a 3/16 inch plate, a stainless knife and a heavy duty stomper, and the headstock, screw, housing and pan are stainless steel, with a tray measuring 3 by 15 by 28 inches.

The practical catches are weight and wiring. The maker lists 140 pounds net and dimensions of 16.3 by 31.1 by 20.5 inches, so this is a machine that gets placed once and stays. It also runs on 220 volts at 9 amps, and the cord arrives without a plug end so the buyer fits an end that matches the 220 volt outlet in the room. Pro-Cut lists NSF and UL certification and a one year warranty, the shortest coverage in this group.

Buying guide

High output figures only help if the rest of the machine matches them. The points below walk through the stated facts that separate these five grinders: how the output numbers were measured, what head size does to prep work, what arrives in the box, and what the drive and the outlet demand from the room.

Read stated output figures with their conditions

A pounds-per-minute figure is only comparable when the conditions match. Pro-Cut prints separate first grind and second grind rates with the plate size and the meat temperature stated, while other makers print a single average or an “up to” ceiling, and those three kinds of numbers describe different things.

An average, like the LEM #32 figure of 17 pounds per minute, is the number to plan a processing day around. A ceiling, like the MEAT! figure of up to 18 pounds per minute, describes the best case with well chilled, well trimmed meat fed steadily. A first grind rate through a coarse plate will always outrun a second grind rate through a fine plate on the same machine, because the fine plate is the bottleneck. When two models look close on paper, the one that states its conditions gives the buyer more to work with.

Head size decides cube size and pace

The head number describes the size of the grinding head and plate: #32 is the largest in this group, then #22. A larger head pairs with a wider throat, 3 inches across on both LEM machines here, and the Pro-Cut throat opens wider still at the top, so bigger cubes drop in and the auger spends its effort grinding instead of waiting.

Smaller cubes are the hidden labor of a big processing day. With a #22 head, plan on cutting meat into narrower strips than a #32 throat accepts, and expect the person feeding the machine to set the pace. The dual grind design answers the same problem from the other side: instead of a wider throat, it removes the second pass entirely, which is where much of the handling time goes on a fine grind.

What high end meat grinders for high volume at home include for stuffing

Every machine in this roundup ships with stuffing gear, but the sets differ. The LEM models include three stuffer tubes in 5/8 inch, 1 inch and 1-3/8 inch sizes, the Weston includes an adapter spacer with four funnels, and the Pro-Cut’s printed box contents stop at a plate, a knife and a stomper.

Tube sizes map to casing sizes: the narrow tube fills snack stick and breakfast sausage casings, the middle tube handles standard hog casings, and the wide tube fills large fibrous casings and meat bags. A kidney plate or stuffing plate, included with the LEM #32 and the Dual Grind, lets the auger push seasoned ground meat into casings without cutting it further. If sausage is half the reason for buying, weigh the stuffing set as heavily as the grinding rate.

Gears, bearings and duty cycle

The drive is where heavy grinders separate from light ones. All five machines state metal drive components: all steel gears with roller bearings in both LEM models, precision-engineered steel gears in the Weston, and an oil bath gearbox with all steel gears in the Pro-Cut, which carries the only stated duty cycle in the group at 100 percent.

A duty cycle rating tells the buyer the machine can run continuously without a cooling rest, which is the difference between grinding 200 pounds in one session and grinding it in shifts. Roller bearings, named by LEM, support the auger shaft under load with less friction than plain sleeve bearings. A built-in circuit breaker, listed for both LEM models, cuts power on an overload instead of letting the motor strain against a jam.

Weight, footprint and power supply

These machines weigh from 49.6 pounds to 140 pounds and occupy footprints up to about 31 inches deep, so measure the bench before ordering. A grinder in this class usually lives where it works: sliding a 75 pound machine out of a low cabinet every weekend is the kind of friction that ends with the machine staying in the cabinet.

Power supply is the second check. Four models here run on 120 volts, with the LEM #32 drawing 13 amps, close to the limit of a shared kitchen circuit, so a lightly loaded circuit is the right home for it. The Pro-Cut needs 220 volts and arrives without a plug end on its cord, which means an electrician or a confident wiring job before the first grind. Tray size is the last fit point: the larger trays here hold a full batch of cubes at once, which keeps the feeder’s hands free.

FAQ

Most questions about grinders in this class come down to pace, power and upkeep: how fast they really run, what outlet they need, which plates arrive in the box, and how a household stores a machine that can weigh as much as a person. The answers below stick to the figures the makers state.

How fast are high end meat grinders for high volume at home?

By the makers’ stated figures, this group runs from 13 pounds per minute for the LEM Dual Grind to 30 pounds per minute for the Pro-Cut on a first grind. The LEM #32 states an average of 17 pounds per minute, the MEAT! #32 states up to 18, and the Weston #32 states a range of 12 to 18 pounds per minute.

Those numbers assume meat that is cubed, well chilled and fed steadily, with fat and sinew trimmed to a reasonable degree. Real pace drops on a second grind through a fine plate, and it drops again when the person feeding the machine has to stop and cut more cubes. For planning, a household processing 100 pounds of meat should allow the grinding itself somewhere between ten minutes and half an hour on these machines, plus all the cutting, mixing and packing time around it.

Does a bigger head size always grind faster?

Not always. Head size sets the plate diameter and throat room, and a #32 head can move more meat per minute than a #22 when the motors are comparable, but the stated figures here cross over: the #22 Pro-Cut states 30 pounds per minute on the first grind, more than either #32 machine, because its 2 HP motor and gearbox drive the smaller head hard.

What head size always changes is the prep work. A wider throat swallows bigger cubes, so less knife time goes into each tray. A smaller head fed with well cut, well chilled meat can outpace a big head fed with warm, uneven chunks that smear instead of cutting. Match the head to the volume: occasional 20 pound batches suit a #22, while repeated 100 pound days reward the #32 throat.

Can these grinders run on a standard kitchen outlet?

Four of the five can. The two LEM models, the Weston and the MEAT! run on 120 volt household current. The LEM #32 draws 13 amps, which is a heavy load on a 15 amp kitchen circuit shared with other appliances, so run it on a circuit with little else drawing power, and never through a light extension cord.

The Pro-Cut KG-22-XP-SS is the exception: it needs 220 volts, and its cord arrives without a plug end, so the buyer supplies an end that matches the 220 volt outlet in the room. That requirement suits a garage, barn or processing room that already has a 220 volt receptacle for other equipment. If the only workspace is a kitchen with standard outlets, stay with the four 120 volt models in this roundup.

What plates come with these grinders?

The LEM #32 includes stainless plates in 3/16 inch and 3/8 inch plus a kidney plate for stuffing. The LEM Dual Grind includes four plates: a first grind plate, 4.5 mm, 10 mm and a stuffing plate. The Weston includes stainless plates in coarse 7 mm and fine 4.5 mm sizes. The Pro-Cut includes a single 3/16 inch plate.

Plate hole size sets texture: the coarse plates around 3/8 inch or 10 mm suit chili grind and the first pass of a two-step grind, while plates near 3/16 inch or 4.5 mm give the finer texture used for burger blends and sausage. Extra plates in other sizes are sold as accessories in each maker’s line, and a plate and knife wear in as a matched pair, so keeping each plate with its own knife preserves the knife-to-plate fit.

How heavy are these machines to move and store?

The stated weights span a wide range: 49.6 pounds for the LEM Dual Grind, 75 pounds for the LEM #32, and 140 pounds for the Pro-Cut. The Weston and MEAT! pages do not state a weight for their #32 models. Anything past about 50 pounds is a two-person lift or a permanent bench placement for most households.

Storage drawers help at every weight: both LEM models keep plates, knives and tubes in a drawer in the housing, and the Weston uses a storage tray with a cover. Before ordering, measure the shelf or bench with the tray included, since the trays here run up to 28 inches long on the Pro-Cut. A machine that lives on the bench under a cover gets used; a machine that must be hauled out of storage gets used less.

Conclusion

For most heavy home use, the LEM Big Bite #32 balances stated output, steel gearing and household voltage best. The Pro-Cut wins on raw stated pace where 220 volts is available, and the LEM Dual Grind wins where a single pass matters more than throat size. The Weston #32 suits households that grind and stuff in the same long session.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.