Updated Nov 17, 2026· 14 min read

Key takeaways

  • Compare under sink pullout storage caddies for bathroom vanities: wire baskets, sliding shelves and clear drawers, with sizes and load limits from the listings.

A bathroom under sink pullout storage caddy turns the dark space under a vanity into storage you can actually reach. This guide compares five pullout caddies that fit under a bathroom sink: two Rev-A-Shelf wire and wood organizers, two HOLDN STORAGE sliding shelves, and a two pack of clear Sorbus pull-out drawers.

Quick verdict

If you need the strongest single basket, the Rev-A-Shelf 5WB1-1520CR-1 holds up to 100 pounds in a 14.5 by 19.75 inch footprint that fits most vanity cabinets. If you need a full vanity organizer, the Rev-A-Shelf 486-30VSBSC-BM-1 is a U-shaped wood unit that fits around the drain, with a 90 pound capacity and an 8 quart waste container included.

For a wide cabinet, the HOLDN STORAGE two tier unit gives you two shelves that slide on their own, each holding up to 50 pounds, while the single tier HOLDN STORAGE basket covers a 17 by 21 inch opening with a chrome wire frame. For small bottles and makeup, the Sorbus two pack of clear pull-out drawers fits in 11.8 by 7.5 inches and lets you see what is inside without pulling the drawer out.

Product Form Size Load
Rev-A-Shelf 5WB1-1520CR-1 Single-tier wire basket 14.5 x 19.75 x 5.56 in 100 lb
Rev-A-Shelf 486-30VSBSC-BM-1 U-shaped wood organizer 25-5/8 x 18-11/16 x 14-1/4 in 90 lb
HOLDN’ STORAGE 17 in Single-tier wire basket 17 x 21 x 6 in Not stated
HOLDN’ STORAGE 2-Tier 20 in Two-tier sliding shelves 20 x 21 x 16.5 in 50 lb per shelf
Sorbus 2-Tier Makeup Two pull-out drawers, 2-pack 11.8 x 7.5 x 11.8 in Not stated

How we selected

Selection started from the listing page for each product, opened one at a time. Only products with a stated form and a stated size on the page made the cut, and each one had to suit the space under a bathroom sink, not just any cabinet. A product with no size on its page did not earn a place, even if the name sounded right.

Two candidates fell out on that rule. A Glidez pull-out organizer page showed only a short description with no dimensions and no load limit, so it was left out. A Rev-A-Shelf two tier basket was fully described, but the listing page marked it sold out, so it was left out too, since a caddy you cannot buy does not help a reader. The five picks below all state a size, and all five were in stock on the pages opened.

Bathroom under sink pullout storage caddy picks, compared in detail

The five picks below cover the main forms of under sink pullout storage: a single wire basket, a U-shaped wood organizer, a wide single basket, a two tier sliding shelf set, and a pair of clear pull-out drawers. Each entry lists the size and load stated on its page, so you can check the fit against your own cabinet before you order.

Rev-A-Shelf 5WB1-1520CR-1 single tier pullout basket

The Rev-A-Shelf 5WB1-1520CR-1 is a single tier pullout steel wire organizer that measures 14.5 inches wide, 19.75 inches deep and 5.56 inches high. The listing page states the basket is strong enough to hold up to 100 pounds, with a three piece zinc plated full-extension ball-bearing slide system, and it installs on the bottom of the cabinet.

The basket is made from heavy gauge plated metal wire, and the listing page says its 20 inch depth is perfect for under the sink, in vanity cabinets, or stacked in a tall pantry cabinet. The minimum cabinet opening is 14.5 inches wide, 19.75 inches deep and 6 inches high, so a vanity with a 15 inch opening takes it with room to spare.

The basket comes with mounting hardware, and the listing page says it mounts to the cabinet floor only, not to the side of a cabinet. A door mount kit, model 5WB-DMKIT, is sold separately if you want the basket to move with the cabinet door. The maker lists a limited lifetime warranty, and the finish is silver steel.

The 100 pound rating is per basket, and the slides carry that load on three pieces of zinc plated steel, so the basket stays level when you pull it out with a full load of bottles. The wire frame lets spills fall through to the cabinet floor, which keeps the tray itself clean, and the silver finish matches most chrome faucets and drains.

Rev-A-Shelf 486-30VSBSC-BM-1 U shaped vanity organizer

The Rev-A-Shelf 486-30VSBSC-BM-1 is a U-shaped wood organizer made for a 30 inch vanity cabinet, measuring 25-5/8 inches wide, 18-11/16 inches deep and 14-1/4 inches high. The U shape fits around the plumbing fixtures under the sink, and the listing page states a weight capacity of 90 pounds on full-extension slides with BLUMOTION soft close.

The unit is built from maple with a non-skid vinyl lining, and it comes with one 8 quart polymer container in metallic silver, four adjustable dividers and bottom mount brackets. The dividers let you split the tray into compartments for bottles and cleaning supplies, and the non-skid lining keeps bottles from sliding when you pull the tray out.

The listing page states a minimum opening width of 25 inches and a minimum opening height of 14-1/2 inches, and the unit comes fully assembled and ready to install. The maker lists a limited lifetime warranty, and the product weight is 22.5 pounds, so the unit itself is heavy enough to stay put once it is mounted to the cabinet floor.

The 8 quart container gives you a small waste bin inside the organizer, so cotton pads and empty bottles have a place without a separate bin on the cabinet floor. The four dividers move to fit tall bottles on one side and short jars on the other, and the vinyl lining keeps glass bottles from sliding when the tray moves.

HOLDN’ STORAGE 17 inch pull out cabinet organizer

The HOLDN’ STORAGE pull-out cabinet organizer in the 17 inch size measures 6 inches high, 17 inches wide and 21 inches deep, with a heavy-duty gauge wire frame in chrome. The listing page says the sliding system lets the organizer extend fully, so you can reach items at the back of the cabinet without kneeling and reaching past the drain pipe.

The organizer fits cabinet openings of 18-1/4 inches and larger, and it comes in sizes from 11 inches to 30 inches wide, so the 17 inch model here is one of nine widths. Installation is simple, with included hardware and straightforward instructions, and the listing page says the organizer is made for everyday use in kitchen cabinets, pantry cabinets and under-sink storage areas.

The listing page states a product weight of 10.43 pounds and a lifetime limited warranty. It states no load limit for this model: the page shows a reader question asking how much weight it can hold, with no answer given. If a stated load limit matters to you, pick a model in this guide that lists one, and do not assume a limit from the wire gauge alone.

The range runs from 11 inches to 30 inches wide, so a narrow vanity takes the 11 inch model and a wide vanity takes the 30 inch model, with the 17 inch model here sitting in the middle. The chrome wire frame wipes clean, and the full-extension glide brings the back of the tray to the front of the cabinet, so nothing hides behind the drain pipe.

HOLDN’ STORAGE 2 tier pull out cabinet organizer 20 inch

The HOLDN’ STORAGE two tier pull-out cabinet organizer measures 20 inches wide, 21 inches deep and 16.5 inches high, with two shelves that slide on their own. The listing page states that each shelf supports up to 50 pounds, and the frame is heavy-duty chrome-plated steel, built for daily use.

The dual shelves bring pots, pans, pantry items, spices, cleaning supplies and small appliances forward, so you no longer have to dig through the back of deep cabinets. Because the two shelves slide on their own, you can pull out the top shelf for a bottle and leave the bottom shelf in place, which matters under a sink where the drain pipe blocks a full pull.

The organizer is in stock on the listing page, and it comes in several sizes besides the 20 inch model. The description on the page is cut off in the middle of the total capacity sentence, so this guide states only the per-shelf figure of 50 pounds that the page states in full, and leaves the total figure unstated rather than guessing it.

Sorbus 2 tier pull out makeup organizers 2 pack

The Sorbus 2-tier pull-out makeup organizers come as a two pack of vanity and skincare storage drawers, with dimensions of 11.8 inches long, 7.5 inches wide and 11.8 inches high. Each bin measures 11.4 inches long, 6.7 inches wide and 2.7 inches high, and the two clear pull-out drawers have built-in handles for easy access to items in the back.

The drawers are made from plastic, and the listing page says the sturdy two tier construction keeps the unit steady while the drawers are in use, with non-slip silicone pads that keep the unit still on shelves, countertops or inside cabinets. The clear drawers let you see the contents at a glance, and the stackable design makes the most of vertical space in small cabinets.

Assembly is tool-free, so the organizers set up in minutes, and the listing page says they suit makeup, skincare, perfumes, lotions, brushes and colognes, fitting under sinks or on countertops. Care is spot or wipe clean, and the listing page states the unit is rust resistant, which suits the damp air under a bathroom sink.

The two pack gives you two identical organizers, so one can sit under the sink and the other on a vanity top or a countertop, or both can stack in one cabinet for four drawers of storage. The clear plastic shows the contents at a glance, so you can find a bottle without pulling every drawer out first.

Buying guide

A pullout caddy lives or dies on fit: the cabinet opening, the drain pipe, the load on the slides and the way the unit mounts. The six points below walk through each one in order, using the sizes and limits stated on the pages for the five picks in this guide, so you can check your own cabinet against a real number before you order.

Measure for a bathroom under sink pullout storage caddy

Measure for a bathroom under sink pullout storage caddy before you order, and measure three ways: side to side, front to back, and top to bottom. The Rev-A-Shelf single basket needs an opening of at least 14.5 inches wide, 19.75 inches deep and 6 inches high, while the U-shaped wood unit needs 25 inches wide and 14-1/2 inches high.

The HOLDN STORAGE single basket fits openings of 18-1/4 inches and larger, and the two tier unit measures 20 inches wide, 21 inches deep and 16.5 inches high, so it needs a tall cabinet. The Sorbus drawers need only 11.8 inches by 7.5 inches of floor, so they fit a narrow vanity. Double check the opening against the product size, and do not forget to account for any obstructions inside the cabinet.

Pick single tier or two tier

Pick single tier or two tier based on what you store. A single tier basket suits tall bottles, cleaning supplies and a waste container, since nothing above the basket blocks the pull. The Rev-A-Shelf single basket holds up to 100 pounds in one tray, and the HOLDN STORAGE single basket gives you a 6 inch high tray across 17 inches of width.

A two tier unit suits small bottles and jars, since two shallow shelves hold more items than one deep tray. The HOLDN STORAGE two tier unit gives you two shelves that slide on their own, each holding up to 50 pounds, and the Sorbus two pack gives you two clear drawers with built-in handles. If you store tall bottles, pick a single tier; if you store small jars, pick two tiers.

Check the load limit on each basket

Check the load limit on each basket before you load it with full bottles. The Rev-A-Shelf single basket states a 100 pound limit on its slides, the Rev-A-Shelf U-shaped unit states a 90 pound capacity, and the HOLDN STORAGE two tier unit states 50 pounds on each shelf.

The other two picks state no load limit on their pages. The HOLDN STORAGE single basket shows a reader question asking how much weight it can hold, with no answer given, and the Sorbus drawers state no load figure at all. If you plan to store heavy cleaning supplies, pick a model that states a limit, and do not assume an unstated limit from the look of the wire or the frame.

Plan around the plumbing

Plan around the plumbing, because the drain pipe and the water lines take the middle of the cabinet. The U-shaped Rev-A-Shelf unit is made for this problem: its U shape fits around the plumbing fixtures, with the tray wrapping the drain instead of hitting it.

The other four picks are flat trays that slide straight out, so they need a clear path past the drain. Measure the pipe position before you order, and check the tray depth against it: the single basket is 19.75 inches deep, the HOLDN STORAGE single basket is 21 inches deep, and the Sorbus drawers are only 11.8 inches deep, so the drawers clear a drain that a full depth tray would hit.

Match the mount to the cabinet

Match the mount to the cabinet, because a pullout caddy that cannot mount to your cabinet is a box you cannot use. The Rev-A-Shelf single basket mounts to the cabinet floor only, not to the side of a cabinet, and it comes with mounting hardware in the box.

The U-shaped unit comes with bottom mount brackets, and the HOLDN STORAGE baskets include mounting hardware for a simple setup. The Sorbus drawers need no mount at all: they sit on the cabinet floor with non-slip silicone pads, and the tool-free assembly sets them up in minutes. If your cabinet floor is uneven or damaged, a freestanding drawer set may suit you better than a screwed-down basket.

Choose wire, wood or plastic

Choose wire, wood or plastic based on what you store and how wet the cabinet gets. Wire baskets suit cleaning supplies and tall bottles, since spills fall through the wire and the steel frame holds heavy loads: the Rev-A-Shelf single basket and both HOLDN STORAGE units use steel wire or a steel frame.

Wood suits a vanity where you want the organizer to look like furniture: the Rev-A-Shelf U-shaped unit is maple with a non-skid vinyl lining, and it comes fully assembled. Plastic suits small bottles and makeup, since a clear drawer lets you see what is inside: the Sorbus drawers are clear plastic with a rust resistant build, and they wipe clean with a damp cloth.

FAQ

The questions below cover the points readers ask most about under sink pullout storage caddies. Each answer uses only the facts stated on the pages for the five picks in this guide, and where a page states no answer, the answer says so rather than guessing.

Which bathroom under sink pullout storage caddy holds the most

The Rev-A-Shelf 5WB1-1520CR-1 single basket holds the most by stated load, at up to 100 pounds on full-extension ball-bearing slides. The Rev-A-Shelf U-shaped wood unit comes next at a 90 pound capacity, and the HOLDN STORAGE two tier unit states 50 pounds on each shelf.

The other two picks state no load limit on their pages, so they cannot be ranked on load. The HOLDN STORAGE single basket shows a reader question asking how much weight it can hold, with no answer given, and the Sorbus drawers state no load figure. If load is the main factor, pick the single basket with the stated 100 pound limit.

How deep should an under sink caddy be

The depth depends on the cabinet and the drain. The picks in this guide range from 11.8 inches deep for the Sorbus drawers to 21 inches deep for the HOLDN STORAGE baskets, with the Rev-A-Shelf single basket at 19.75 inches and the U-shaped unit at 18-11/16 inches.

A deep tray holds more, but it needs a clear path past the drain pipe. A shallow drawer holds less, but it fits a cabinet where the drain sits close to the front. Measure the cabinet from the front edge to the drain pipe, then pick a depth that leaves room for the tray to slide past it without hitting the pipe.

Can a pullout caddy fit around a drain pipe

Yes, if you pick a U-shaped unit. The Rev-A-Shelf 486-30VSBSC-BM-1 is a U-shaped wood organizer made to fit around the plumbing fixtures under a sink, with the tray wrapping the drain instead of hitting it. It is made for a 30 inch vanity sink base cabinet, with a minimum opening width of 25 inches.

A flat tray cannot wrap a drain, so it needs a clear path past the pipe. The single basket is 19.75 inches deep, the HOLDN STORAGE baskets are 21 inches deep, and the Sorbus drawers are 11.8 inches deep, so a shallow drawer clears a drain that a full depth tray would hit. Measure the pipe position before you order, and pick the form that fits around it.

Do pullout caddies need screws

Most pullout caddies in this guide need screws, and they include the hardware. The Rev-A-Shelf single basket mounts to the cabinet floor with included mounting hardware, the U-shaped unit comes with bottom mount brackets, and the HOLDN STORAGE baskets include mounting hardware for a simple setup.

The Sorbus drawers are the exception: they sit on the cabinet floor with non-slip silicone pads, and the tool-free assembly sets them up in minutes with no screws at all. If you rent and cannot drill into the cabinet, a freestanding drawer set is the pick that leaves no holes behind when you move out.

Conclusion

Five pullout caddies cover most bathroom vanities: a 100 pound single basket for heavy bottles, a U-shaped wood unit that wraps the drain, two HOLDN STORAGE sliding shelves for wide cabinets, and a pair of clear Sorbus drawers for small items. Measure the opening, plan around the drain, and check the load limit before you order.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.