Key takeaways
- Compare audio mixers for PC gaming, streaming and calls, with verified XLR inputs, phantom power, virtual device counts, app control and operating support.
A PC mixer earns its desk space by giving every app its own level: game, chat, music and your microphone, all adjustable without alt-tabbing. This guide compares audio mixers for pc setups using the makers’ published inputs, virtual devices, app features and system requirements. One is a pure control surface; five take XLR microphones directly.
Quick verdict
Short on time? The Razer Audio Mixer and Yamaha ZG01 are built for game streamers, the BEACN Mix Create is the deepest PC-app controller here, the Rode Streamer X adds video capture, and the Hercules and AVerMedia decks suit podcast desks and call-heavy workdays.
- Razer Audio Mixer: the fader desk, four slide faders with a hybrid XLR input and Synapse-powered mic processing.
- Yamaha ZG01: the console gamer’s pick, HDMI game audio plus two virtual USB devices for voice and streaming.
- BEACN Mix Create: the app controller, no audio inputs of its own, just deep control over every app on the PC.
- Rode Streamer X: the two-in-one, a 4K capture card and audio interface with a wireless mic receiver built in.
- Hercules Stream 200 XLR: the track stack, up to 32 tracks paged across four knobs with a 48 V XLR input.
- AVerMedia Live Streamer NEXUS AX310: the touch deck, a 5-inch touch panel and six encoders over six audio tracks.
How we selected
A PC mixer lives or dies on its software side, so the picks below weigh virtual audio devices, per-app volume control, driver and app requirements and operating system support as heavily as XLR inputs, phantom power and the physical controls on the desk.
The group divides into three shapes. Dedicated streaming mixers (Razer, Yamaha) put faders and game-focused effects on the desk. Control surfaces (BEACN, Hercules, AVerMedia) assume the PC does the audio work and compete on screens, knobs and routing depth. The Rode sits between the camps, adding video capture and a wireless receiver to the interface job. Every pick connects over USB, and every spec below is the maker’s own published figure or feature wording.
One caution runs through the list: operating system support is not uniform. Two of the six are Windows-only propositions in practice, while others publish Mac support with minimum versions. The buying guide starts there, because it is the cheapest mistake to avoid.
Top audio mixers for pc gaming and streaming compared
All six picks connect to the computer over USB and split your sound into channels you can ride live. They differ in how the mixing happens: physical faders and knobs here, app-driven routing there, and one unit that captures game video as well as audio.
| Product | Mic input | PC connection | Control style | Standout extra |
|---|---|---|---|---|
| Razer Audio Mixer | Hybrid XLR/6.35 mm, 48 V phantom | USB-C | 4 slide faders | Optical console input |
| Yamaha ZG01 | Combo mic input, +48 V phantom | USB Type-C + 3 x HDMI | Knobs + 6 effect buttons | 2 virtual USB devices |
| BEACN Mix Create | None (controls PC audio) | USB-C (USB 2.0) | 4 knobs + 5-inch screen | Personal + audience mixes |
| Rode Streamer X | Neutrik combo jack | Dual USB-C | SMART pads + level controls | 4K30 capture, wireless receiver |
| Hercules Stream 200 XLR | XLR, 48 V phantom | USB-C (USB 2.0) | 4 rotary knobs, 8 pages | Up to 32 tracks |
| AVerMedia Live Streamer NEXUS AX310 | XLR/6.3 mm, +48 V phantom | USB 2.0 Type B | 6 encoders + 5-inch touch panel | Creator/Audience dual mix |
Razer Audio Mixer
Razer’s Audio Mixer is a 4-channel digital mixer built for broadcast and streaming, with slide faders, per-channel mute buttons and a hybrid XLR port with 48 V phantom power. Razer Synapse handles the deep settings; the desk stays hardware-controlled in daily use.
The four channels map to the sources a streamer actually rides: a direct line out for the microphone plus game, music/chat and system volumes. The XLR preamp’s gain adjusts from -12 dB to +39.7 dB in 0.75 dB steps, and Synapse adds EQ, a compressor and a noise gate for the mic channel. Connections cover a 3.5 mm line in and out, a 3.5 mm microphone in and an optical input for console audio, all alongside the USB-C link to the PC.
Live-control touches fill out the desk: a microphone mute button, a bleep button that mutes and censors on the spot, and mute buttons that double as voice-modification triggers when held. Voice changer presets such as Monster and High Pitch, echo and reverb, a key shifter and vocal fading sit in the software. Chroma RGB lighting shows levels and mute states, and Razer says the mixer serves single or dual PC setups without extra cables and hardware. It requires Windows 10 or above with Synapse, and Razer’s materials state it is not compatible with macOS or USB microphones.
Yamaha ZG01
Yamaha’s ZG01 is the maker’s first mixer designed for game voice chat and game streaming, and it routes console audio over HDMI as well as PC audio over USB. Six effect buttons cover voice chat and game sound, and chat gets its own virtual device on the PC.
Three HDMI ports (two in, one out) pass video through while taking console audio at 2 channels, 24-bit/48 kHz fixed; Yamaha notes there is no video capture function, so a capture card still handles the picture. The microphone input is a combo jack with +48 V phantom power and a mute button, joined by a 3.5 mm headset mic input and a 4-pole TRRS connection for a smartphone. USB audio runs at 24-bit/48 kHz, and after the dedicated driver is installed (Windows or Mac), the PC sees two virtual devices, Voice and Streaming, so chat and broadcast levels stay separate.
Yamaha’s processing aims at game audio specifically: ZG SURROUND uses the maker’s ViReal technology for headphone immersion, FOCUS MODE/EQ can suppress your own character’s voice or bring out environmental sounds, and 3D CHAT SPACE places the other party’s voice in a virtual space so it stops colliding with game sound. Voice effects include a voice changer, a transceiver radio voice, a masking beep and one-touch echo. The unit draws 5 V DC at 1.5 A, measures 195 x 47.5 x 110 mm and weighs 0.8 kg.
BEACN Mix Create
The BEACN Mix Create is the odd one out in the best sense: a USB-C control surface with no audio inputs at all, built to mix the sound your PC already handles. Four knobs with paging manage unlimited apps across a personal mix and an audience mix on one screen.
BEACN is explicit about the design: the unit is USB-C only by choice, with no XLR or other inputs and outputs, and it works with any audio hardware the computer can access, so an existing interface or USB microphone stays in the chain. The four infinite-scroll knobs accept drag-and-drop app assignments, and knob paging opens further channel pages without more hardware. A routing table with mute modes decides where each app goes, and a dedicated VOD output keeps selected sources out of the saved video track.
The hardware is a 5-inch LCD (800 x 480) in a body measuring 174 x 90 x 100 mm, connecting over USB 2.0 through the USB-C port. Two mixes run at once, a personal mix for your headphones and an audience mix for the stream, switched at a button. System requirements are Windows 10 or later, or macOS 12 or later on M1, M2 or Intel Macs. For a desk that already owns a good microphone path, this is the purest mixing upgrade in the group.
Rode Streamer X
Rode’s Streamer X folds a video capture card, an audio interface and a control surface into one box for a PC streaming desk. It captures up to 4K30 over HDMI with 4K60 pass-through, and its Neutrik combo jack takes an XLR microphone or an instrument.
The audio side pairs that combo jack and its Revolution Preamp with a 3.5 mm TRRS headset input and a 1/4-inch headphone output with zero-latency monitoring. An integrated wireless receiver connects Rode Series IV wireless microphones, including the Wireless PRO, Wireless GO II and Wireless ME, so a lav can join the desk without another receiver. Internal DSP powered by APHEX handles processing, and four SMART pads trigger sounds, voice effects and MIDI commands, with up to 64 pads reachable through bank switching.
Dual USB-C interfaces connect the Streamer X to two computers or consoles at once, which suits a gaming PC plus streaming PC desk. Rode’s free UNIFY software handles advanced routing, mixing and configuration, and dedicated controls cover mic and headphone levels with large audio and video mute buttons. The unit also accepts Rode USB microphones as an additional mic input. Variable Refresh Rate support keeps the captured picture in step with high-refresh gaming monitors.
Hercules Stream 200 XLR
The Hercules Stream 200 XLR calls itself a complete sound card and runs up to 32 tracks across eight pages of four rotary knobs. An XLR input with 48 V phantom power anchors the microphone side, and a Creator/Audience button swaps the mix you hear live.
Each of the four rotary buttons manages a track’s volume with mute support, and stereo VU meters (2 x 2 per track) show levels on the 4.3-inch TFT LCD. The microphone path combines a 20 dB internal amplifier with a 24 dB adjustable JFET stage, and mic effects cover a noise gate, compressor, equalizer and limiter. Audio runs at 24-bit/48 kHz over USB 2.0 Type-C with a driver required, and Hercules publishes a 110 dB dynamic range and a 20 Hz to 20 kHz frequency response.
Connections add an optical Toslink input, 3.5 mm line in and line out, and a 3.5 mm headphone output rated at 64 mW on 32 ohms. Four action buttons carry up to 32 assignable actions, profiles store up to 12 desk setups, and the Hercules Stream Control app arrives with Discord, Spotify, Voicemod, Twitch, OBS and Streamlabs pre-integrated. The unit measures 155 x 110 x 115 mm and weighs 543 g; the maker’s stated minimum is Windows 10 or higher.
AVerMedia Live Streamer NEXUS AX310
AVerMedia’s Live Streamer NEXUS AX310 puts a 5-inch IPS touch panel and six rotational encoders on the desk, split between three physical inputs and three digital tracks from the PC. Creator Mix and Audience Mix modes run as a single mix or a dual mix.
The physical inputs are an XLR/6.3 mm microphone input with +48 V phantom power switched through the NEXUS app, an optical Toslink console input and the third input completing a set of three, matched against three digital tracks from the computer for six audio tracks in total. Sampling runs up to 96 kHz at 24 bits, with a published frequency response of 10 Hz to 20 kHz and a dynamic response of 114 dB. Microphone effects include a noise gate, reverb, compressor and equalizer, and outputs are 3.5 mm headphone and line connections.
The touch panel carries a customizable widget grid, RGB lighting accents the deck, and four function buttons sit alongside the encoders. The unit runs from a 12 V DC supply at under 7 W, measures 21.7 x 14.5 x 6.1 cm without its stand and weighs 0.699 kg. AVerMedia’s requirements are Windows 10 20H2 (64-bit) and above or macOS 10.15 and above, the widest Mac support window in this group.
Buying guide: audio mixers for pc desks
Choosing a PC mixer starts with the microphone you own and the operating system you run, because both narrow the field fast. After that, the real differences are how many apps get their own channel and whether the controls are physical or on a screen.
Check operating system and driver support first
Software support is the first filter, because a mixer your OS cannot run is furniture. Razer requires Windows 10 or above and Synapse, Hercules lists Windows 10 or higher, and BEACN and AVerMedia publish Mac support with stated minimum versions to check.
Mac users should shortlist the BEACN (macOS 12 or later), the AX310 (macOS 10.15 and above) and the ZG01 (a dedicated driver for Windows and Mac). Windows users can consider all six, but should still note the driver requirements: the Hercules and AVerMedia units state a driver is required, and Razer’s deep settings live inside Synapse. A mixer that depends on an app also depends on that app’s update cadence, which is worth weighing for a desk you plan to keep for years.
XLR input and phantom power for your microphone
Five of the six picks take an XLR microphone directly, and four publish 48 V phantom power for condensers. Preamp gain matters with quiet dynamic mics: Razer publishes an adjustable range from -12 dB to +39.7 dB, and Hercules adds a JFET stage on top.
Match the input to the microphone you actually own. A condenser needs the phantom power that the Razer, Yamaha, Hercules and AVerMedia publish. A headset user is served by the ZG01’s 3.5 mm headset input and the Streamer X’s TRRS jack. And if your microphone is USB, read the FAQ below before buying anything with an XLR socket: the BEACN is the only pick designed to sit on top of an existing USB mic setup.
Virtual devices and dual-PC routing
Virtual devices decide how cleanly apps separate. Yamaha’s ZG01 appears as two virtual devices for voice and streaming, Razer splits mic, game, music/chat and system across four faders, and BEACN assigns unlimited apps to four knobs through paging in its app.
Dual-PC streamers should look at the Razer, which Razer says covers single or dual PC setups without additional hardware, and at the Streamer X, whose dual USB-C interfaces connect two computers or consoles directly. Console players route differently again: optical inputs on the Razer and Hercules and HDMI audio on the ZG01 each pull game sound into the PC mix without analog cables from the console.
Faders, knobs, pads or touch: pick a control style
Control feel is personal, and this group covers every style: Razer’s slide faders, rotary knobs on the Yamaha and Hercules, BEACN’s endless knobs with a screen, Rode’s trigger pads and AVerMedia’s touch panel with encoders for each track on the desk.
Think about what your hand does mid-stream. Faders give instant, eyes-free level rides; paged knobs trade that immediacy for far more channels per square inch, as the Hercules shows with 32 tracks behind four knobs. Pads suit desks that fire sounds and effects constantly. A touch panel with widgets suits streamers who want stream controls and audio in one surface. None of these is objectively best; the right one is the one your hand learns fastest.
FAQ: audio mixers for pc setups
These are the questions PC builders ask before buying a desk mixer: whether a USB microphone works, whether one mixer can serve two PCs, and how the audience mix differs from what you hear in your headphones while streaming or recording at home or at work.
Can I use my USB microphone with these mixers?
Mostly no for the XLR models, and it depends for the control surface. Razer’s materials state its mixer is not compatible with USB microphones, while BEACN states the Mix Create works with any audio hardware your computer can access, USB mics included.
The exception on the XLR side is the Rode Streamer X, which accepts Rode USB microphones as an additional mic input alongside its combo jack. Everywhere else, the microphone plugs into the mixer’s own XLR or headset input, and the mixer becomes the PC’s audio device. If a USB mic is non-negotiable, the BEACN route keeps it and adds mixing control on top.
Can one mixer run a dual-PC streaming setup?
Yes, two picks here are built for it. Razer says its mixer serves single or dual PC setups without additional cables and hardware, and Rode’s Streamer X carries dual USB-C interfaces for connecting to two computers or consoles at the same time on one desk.
The two designs solve the same problem differently: Razer routes the second PC’s audio through its line and optical connections, while Rode gives each computer its own USB interface. Single-PC streamers lose nothing by choosing either; both run a one-PC desk fully. The ZG01’s twin virtual devices solve a different split, separating voice chat from the broadcast inside one PC.
What is the difference between a personal mix and an audience mix?
A personal mix is what you hear in your headphones; an audience mix is what the stream or recording receives. BEACN builds its whole unit around switching between the two, and the Hercules and AVerMedia decks offer the same split under Creator and Audience labels.
The split matters when your monitoring needs differ from the show: you might keep a loud click track, a quiet co-host feed or your own voice louder in your headphones than the audience should hear. Dual-mix control lets you set both balances independently and swap your monitoring between them at a button, which is why the feature anchors three of the six picks here.
Do these mixers work on a Mac?
Support splits by model. Razer requires Windows 10 or above with no macOS support, Yamaha’s ZG01 installs a dedicated driver on Windows or Mac, BEACN requires macOS 12 or later alongside Windows 10, and AVerMedia lists macOS 10.15 and above for the AX310.
Hercules states Windows 10 or higher as its minimum requirement, so Mac buyers should treat that unit as Windows-first. Rode’s Streamer X relies on the UNIFY software for routing and configuration; check Rode’s current support pages for your macOS version before buying. When a maker publishes a minimum version, staying one release behind it is the practical way to keep a streaming desk stable.
Can a PC mixer add voice effects for streams and calls?
Yes, and the depth varies. Razer and Yamaha build in voice changers and playful presets, Rode adds APHEX processing and pads that trigger voice effects, and the Hercules and AVerMedia decks focus on corrective tools like gates, compressors and EQ for the mic channel.
For calls and meetings, the corrective set is the useful one: a noise gate trims keyboard clatter between sentences, a compressor evens out volume, and a de-esser (Razer, via Synapse) softens harsh consonants. The playful set (voice changers, radio effects, pitch shifts) belongs to entertainment streams. BEACN owners get neither from the unit itself, since it controls app audio rather than processing a microphone.
Conclusion
For a PC desk, the Razer Audio Mixer and Yamaha ZG01 serve game streamers first, the BEACN Mix Create gives the deepest control over app audio, the Rode Streamer X adds capture and wireless options, and the Hercules and AVerMedia decks bring big control surfaces to podcasts and calls. Match the mixer to your microphone and operating system first.