Key takeaways
- Five large-format consoles compared for music festivals, from DiGiCo and Avid to Yamaha, Allen and Heath and Soundcraft, with channel counts and monitor mixes.
Quick verdict
Short on time? The DiGiCo Quantum 338 and Avid VENUE S6L are the two surfaces guest engineers ask for most, the Yamaha DM7 brings festival capacity in a smaller footprint, the Allen and Heath dLive system pairs a fast surface with a separate mix rack, and the Soundcraft Vi7000 remains the touchscreen-led alternative with up to 128 inputs.
| Product | Input channels | Mix capacity | Faders | Sample rate | Standout feature |
|---|---|---|---|---|---|
| DiGiCo Quantum 338 | 128 | 64 aux/sub-group buses | 38 motorized | 48/96 kHz | Mustard and Nodal processing |
| Avid VENUE S6L | Up to 256 by engine | 192 buses + LCR | 48 + 2 (S6L-48D) | 96 kHz | 400 AAX DSP plug-in slots |
| Yamaha DM7 | 120 mono | 48 mix + 12 matrix | 24 + 4 | Dante 144 x 144 | Dan Dugan automixer to 64 ch |
| Allen and Heath dLive S7000 | 128 | 64 mix outputs | 36 | 96 kHz | 0.7 ms latency XCVI core |
| Soundcraft Vi7000 | 128 | 32 mono/stereo buses | 32 + 8 bus faders | 48 kHz, 96 optional | Five Vistonics touchscreens |
How we selected these mixers for music festivals
Festival duty set the entry bar: at least 96 input channels of mixing capacity, enough buses to run FOH plus a serious monitor count, snapshot or show-file handling for rapid band changeovers, and a surface a visiting engineer can learn during a line check. Every console here clears that bar with room to spare.
Systems were verified from manufacturer pages, datasheets and full specification documents opened during research, using the makers’ current models only. Consoles aimed at theatres, broadcast or houses of worship were left out unless they also headline festival main stages, and smaller-format desks were excluded however good they are: a 48-channel board cannot take a full festival patch with guest acts layered on top.
Rider acceptance counted as a selection factor in its own right. Festival headliners travel with their own engineers and show files, so a console earns its place partly by being the system those engineers request. Each pick here is a current flagship or near-flagship in its maker’s live range, the level at which rider requests concentrate, rather than a mid-range desk stretched beyond its intended work.
The five mixers for music festivals in detail
All five are split systems in spirit: a control surface at FOH, serious processing power behind it, and digital stageboxes at the stage end. They differ in how the surface feels, how plug-ins and processing are handled, and how their show files travel from one festival to the next.
DiGiCo Quantum 338
The Quantum 338 is DiGiCo’s festival workhorse: 128 input channels, 64 aux and sub-group buses, and a master section switchable between LR, LCR, LCRS and 5.1, with a 24 x 24 full processing matrix behind it. Thirty-eight 100 mm touch-sensitive motorized faders sit under three 17-inch 1000-nit multitouch screens.
The 1000-nit screen brightness is an outdoor specification, not a luxury: FOH positions at summer festivals sit in direct sun for the afternoon sets, and a surface that cannot be read cannot be mixed on.
Processing depth is the Quantum story. There are 286 dynamic equalizers across the system and 24 stereo internal effects. Mustard Processing provides 36 fully featured channel strips with tube preamp emulations and EQ variants, Nodal Processing gives 64 processors that let each monitor send carry its own processing, and the Spice Rack holds 8 mono or 4 stereo effect slots. Twenty-four 32-band graphic EQs cover outputs. Local I/O includes 8 channels of 32-bit mic/line inputs and outputs plus 8 AES I/O, and six MADI interfaces (three at 96 kHz) with triple redundancy link the stage racks. A built-in UB MADI USB interface records the show without extra hardware.
The console runs at 48 or 96 kHz with a typical processing delay of 1 ms. It measures 1595 x 805 x 482 mm and weighs 70 kg on its own, or 198 kg in its flightcase, drawing 295 VA from a 100-240 V supply. Two DMI slots accept format cards for further connectivity.
- Pros: huge per-send processing through Nodal, built for monitor-heavy festivals; sunlight-readable screens and a familiar layout for guest engineers; triple-redundant MADI and a built-in recording interface; Mustard strips add channel character without plug-in hosts
- Cons: the heaviest single surface here once cased; the processing options take time to learn beyond the basics; DMI cards add to the system for some formats
Buy if: your festival hosts guest engineers daily and monitor sends need their own processing per mix. Skip if: your stages are small enough that a compact console covers the patch.
Avid VENUE S6L
The VENUE S6L is a modular system: pick a surface (S6L-48D down to S6L-16C), an engine (E6LX-256 down to E6LX-112) and Stage 64 I/O racks. In its largest form the E6LX-256 engine provides 256 input channels at 96 kHz, 192 mix buses plus LCR, a 64 x 64 matrix and 48 VCAs, which is the biggest mix capacity on this list.
Plug-ins are the S6L signature: 400 slots of 64-bit AAX DSP plug-ins run inside the system, with Waves SoundGrid available through the WSG-HD card, so engineers can carry studio processing to a festival field. Recording goes straight to Pro Tools, up to 128 tracks over AVB or 216 via the MLN-192 Milan option. Each Stage 64 rack provides 64 inputs and 32 outputs at 96 kHz, and up to three racks give 192 inputs and 96 outputs.
Surfaces carry 12-inch daylight-visible touchscreens and local I/O (8 XLR mic/line inputs with 48V, 8 XLR outputs and AES/EBU pairs on the larger models). The Ethernet AVB network runs as a redundant ring, and power supplies are dual redundant and hot-swappable. The flagship S6L-48D surface has 48 + 2 faders, measures 76.1 inches wide and weighs 212 lbs; smaller surfaces scale down to the 72 lb S6L-16C.
- Pros: the largest channel and bus counts here in top configuration; AAX DSP plug-ins inside the console, no external server needed for the core count; Pro Tools multitrack recording is native to the workflow; modular surfaces and engines scale to the stage size
- Cons: a full system is several pieces to specify, ship and connect; the biggest surface is a two-person lift at 212 lbs; Waves integration needs the extra card
Buy if: your headliners travel with S6L show files and plug-in chains, and your stages run the largest patches. Skip if: you want one self-contained console per stage with no system design step.
Yamaha DM7
The DM7 is the compact entry among giants: 120 mono input channels (72 on the DM7 Compact), 48 mix buses, 12 matrices, 2 stereo buses and a mono bus, with 24 + 4 faders on the standard model. Two 12.1-inch multitouch screens plus a 7-inch screen keep the footprint down to 793 mm wide and 23.5 kg, light enough for one person to move.
Connectivity is Dante-first, with 144 inputs and 144 outputs of Dante alongside 32 analog inputs and 16 analog outputs on the standard model. A USB host connection provides 18 in and 18 out for recording or playback. The Premium Rack carries plug-ins derived from Yamaha’s Portico collaborations (5033, 5043 and 5045) plus U76 and Opt-2A models, and the Effect Rack offers 43 effect types. Input channels have 4-band full parametric EQ; outputs get 8-band.
Festival-relevant helpers include a Dan Dugan Automixer for up to 64 channels, useful for festival talk and announcement stages, 24 DCA groups, 12 mute groups and 500 scenes for changeovers. A built-in dual power supply covers redundancy without an external unit.
- Pros: festival-scale channels and buses in a 23.5 kg console; Dante capacity of 144 x 144 for networked stages; built-in dual power supply; 500 scenes suit rapid-fire changeovers
- Cons: fewer faders on the surface than the DiGiCo or dLive, so more layer switching; analog I/O on the surface is modest, leaning on Dante stageboxes; plug-in rack is Yamaha’s own rather than third-party DSP
Buy if: your festival runs Dante infrastructure and needs big-console capacity that one technician can deploy. Skip if: your engineers expect 36-plus physical faders in front of them.
Allen and Heath dLive S7000
The dLive system splits the work between the S7000 surface and a MixRack, here the DM64 with 64 mic/line inputs and 32 XLR outputs in 10U. The XCVI core inside the rack runs 128 input channels with full processing and 64 mix outputs on a configurable 64-bus architecture at 96 kHz, with a latency of just 0.7 ms, the lowest figure on this list.
The S7000 surface carries two 12-inch touchscreens, 36 faders, 26 assignable SoftKeys and 6 assignable rotaries. Dual redundant gigaACE and DX links connect surface and rack, two I/O ports on the surface each carry 128 channels at 96 kHz, and up to four surfaces can share one MixRack, which suits a festival running FOH and monitors from the same engine. Sixteen RackFX units and DEEP processing models provide the effects and channel emulations, with 16 DCAs for grouping.
The DM64 MixRack adds three audio interface ports of 128 x 128 channels each for recording and networking, and its power supply is dual redundant and hot-swappable (one fitted, a second available). Smaller DM32 and DM48 racks scale the same system down for side stages.
- Pros: 0.7 ms latency and a 96 kHz FPGA core; up to four surfaces on one MixRack for FOH plus monitors; dual redundant links and power options; the same show files scale across the dLive range
- Cons: surface carries only 8 local mic inputs, so stage I/O depends on the rack position; second MixRack power supply is an added option; guest engineers from other ecosystems face a learning curve
Buy if: you want one engine serving FOH and monitor surfaces, with the lowest latency here. Skip if: your stages need the surface itself to hold most of the I/O.
Soundcraft Vi7000
The Vi7000 pairs a control surface with a Local Rack and stageboxes for up to 128 inputs to mix and 32 mono/stereo buses; since every bus can run in stereo, the console offers up to 32 stereo mixes, a strong monitor position for in-ear heavy festival shows.
Five Vistonics II touchscreens, each with its own switches and encoders, put the controls where you look, and FaderGlow lights each fader track by function so two engineers can share the surface.
Processing runs on a 40-bit floating point DSP engine at 48 kHz, with an optional move to 96 kHz using additional DSP cards at a reduced channel count of 64 inputs. Eight independent stereo Lexicon multi-effects units, 16 instances of the BSS DPR901ii Dynamic EQ and a BSS graphic EQ on every bus output cover the festival effects load, and STUDER vMIX automixing handles up to four groups of 16 inputs for announcement and talk stages.
The Local Rack system supports up to 384 I/O channels through expansion, with a 128-channel record interface over MADI or Dante for multitrack capture and virtual soundcheck. Cue list management, snapshot crossfades and MIDI or GPIO event integration handle festival changeovers, and the ViSi Remote iPad app lets engineers adjust monitors from the stage. Published figures include stagebox mic EIN below -126 dBu, latency under 2 ms at 48 kHz, and dual redundant power supplies; consumption is 300 W.
Setup speed gets its own hardware: dedicated Copy and Paste buttons on the surface copy settings between channels, buses and FX sections, down to single processing elements, with an undo for the last paste. A settings library stores EQ and dynamics setups on the console or a USB stick, and VM2 monitoring shows Shure ULX-D and QLX-D and HiQnet-compatible AKG radio mic battery, RF and muting status on the surface, which matters when a headline set depends on radio mics.
- Pros: five touchscreens make the fastest surface here for engineers who think in pictures; all buses stereo-capable for in-ear monitor worlds; deep cue and snapshot system for changeover days; radio mic status monitoring for Shure and AKG systems from the surface
- Cons: 96 kHz operation costs extra DSP cards and halves the input count; the surface and Local Rack travel as separate pieces; a long-standing design that power users either love or avoid
Buy if: your engineers mix visually, your monitor count is high, and your festival days run on cues and snapshots. Skip if: full 128-input mixing at 96 kHz is a hard requirement.
Buying guide: choosing mixers for music festivals
Festival consoles are bought for changeover speed and guest-engineer acceptance as much as for sound, and the running order of a festival day exposes every weak point in a system. The checks below reflect how these systems earn their keep across a weekend of backline swaps and headline sets.
Channel and bus counts for the real patch
Count the biggest day, not the average one: headline patch plus support acts, talk and announcement feeds, ambient mics and spare lines for failures and last-minute additions. Then count monitor mixes, since in-ear worlds consume buses faster than FOH does.
All five systems here start at 120-plus inputs; they separate on bus architecture, from the Vi7000’s 32 stereo-capable buses to the S6L’s 192.
Guest engineers and show files
A festival console spends half its life under visiting hands. Surfaces with daylight-readable screens, clear labeling and known layouts, like the Quantum 338 and S6L, shorten every soundcheck. Ask your likely headliners’ engineers what files they travel with; matching the desk to the rider avoids a week of translation work before the gates open.
Changeover tools
Scenes, snapshots and cue lists are the changeover machinery: 500 scenes on the DM7, cue lists with crossfades on the Vi7000, and snapshot systems on the rest. Check how much of the console a scene can recall and what it can leave alone, because festival days need the house engineer’s monitor settings protected while the guest’s FOH file loads.
Redundancy and outdoor duty
Look for dual power supplies, redundant network links and stagebox connections that survive a kicked cable: triple-redundant MADI on the Quantum, a redundant AVB ring on the S6L, dual gigaACE on the dLive, and dual PSUs across the Yamaha and Soundcraft. Weight and case size matter too, since every surface here travels between stages and sites.
Recording and virtual soundcheck
Festivals increasingly record every set. Built-in or card-based multitrack paths, UB MADI on the DiGiCo, Pro Tools over AVB on the S6L, Dante on the DM7 and the Vi7000’s MADI or Dante interface, let the next band’s line check double as a virtual soundcheck from yesterday’s recording, which is how tight changeovers stay calm.
Processing character and plug-ins
Each family has a processing accent that engineers choose on purpose. The S6L runs 400 AAX DSP plug-in slots inside the system; DiGiCo answers with Mustard channel strips and Nodal per-send processing; dLive offers DEEP modeled processing in the core.
Yamaha fits its Premium Rack with Portico-derived plug-ins, and the Vi7000 builds in BSS dynamic EQ and Lexicon effects. A guest engineer’s file only sounds as intended inside its own family, which is why this choice follows the rider, not the brochure.
FAQ
Questions promoters, production managers and house engineers ask when speccing festival consoles, covering counts, staffing, latency and what separates these systems from large club desks. Most answers come down to the same trade: capacity and familiarity against size, weight and system complexity.
How many input channels does a festival console need?
A main stage with a headline band, support acts pre-patched, DJ and playback feeds, talk mics and spares can pass 100 inputs quickly, which is why every console here starts at 120 or more. Side stages can run smaller systems, but the main stage figure should be set by the largest single day’s patch, not by the headliner alone.
Can one console run both FOH and monitors at a festival?
It can, and the bus counts here allow it, but most festivals split the jobs between two surfaces for staffing and sightline reasons. The dLive design supports that directly, with up to four surfaces on one MixRack, while the DiGiCo’s Nodal Processing takes the other route and gives each monitor send its own processing from a single console.
Why do festival engineers care about latency figures?
Performers on in-ear monitors hear the console’s delay on top of the rest of their chain, and drummers and singers notice delays quickly. Figures run from 0.7 ms on the dLive core to under 2 ms on the Vi7000 at 48 kHz, all within the range monitor engineers accept; the number matters most when digital wireless and plug-in hosts add their delay.
What is a show file, and why does it decide festival bookings?
A show file stores an engineer’s whole console setup: patch, processing, scenes and effects. Headline engineers travel with files built for a specific console family, so a festival that stocks that family loads the file and starts from the engineer’s own mix. It is the practical reason the same few consoles appear on rider after rider.
Do these consoles record the performances?
Yes, each system has a multitrack path: the Quantum 338 records over its built-in UB MADI USB interface, the S6L records to Pro Tools over AVB, the DM7 uses its USB and Dante connections, dLive records through its interface ports, and the Vi7000 offers a 128-channel interface over MADI or Dante.
Conclusion
The DiGiCo Quantum 338 and Avid VENUE S6L remain the default mixers for music festivals at headline scale, the dLive S7000 answers with the lowest latency and flexible surfaces, the Yamaha DM7 packs festival capacity into the smallest footprint here, and the Soundcraft Vi7000 serves engineers who mix fastest on touchscreens.