Key takeaways
- Six racks that fit a PreSonus StudioLive rack mixer, compared on maker specs: rack units, usable depth, case weight, load capacity, rails, lids and casters.
PreSonus prints the numbers that start this search: the StudioLive 32R and SE 32R are 19 inches wide, 3.5 inches tall and 12 inches deep, at 11.2 pounds. This guide picks a studio rack to go with presonus mixers by matching those figures against each rack maker’s printed rack units, usable depth, rails and weight.
Quick verdict
For a studio that stays put, take the Middle Atlantic BRK12: 12U of furniture rack with a 200 pound capacity and 17.4 inches of inner depth, enough for the mixer, power, networking and a drawer. For a mixer that travels, take the Gator GR-6L: 6U, a 19.25 inch rackable depth, locking latches and a 14 pound shell.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Gator G-PRO-4U-19 | Roto molded road case | A compact mixer-plus-power rig | 4U, 19 inch rackable depth, 12 lb case | Only 4U of space; not lockable |
| Gator GR-6L | Lightweight road case | Touring with room to grow | 6U, 19.25 inch rackable depth, lockable | Polyethylene shell, not a flight panel case |
| SKB 3i-2317M146U Fly Rack | Waterproof fly case | Fly dates and outdoor stages | 6U removable cage, watertight case | 13 inch rack depth is tight behind a 12 inch mixer |
| Gator G-TOUR EFX6 | ATA wood flight case | Truck and trailer touring | 6U, 15 inch depth, 9mm plywood | Shallow depth limits rear cabling room |
| Middle Atlantic BRK12 | Freestanding studio rack | A fixed studio corner | 12U, 200 lb capacity, 17.4 inch inner depth | Furniture, not a travel case |
| On-Stage WSR7500RB | Rolling studio cabinet | Beside a workstation desk | Casters fitted, 30.5 inch height on casters | Maker catalog prints no rack-space count |
How we selected
The reference point is the mixer’s spec sheet. PreSonus lists the StudioLive SE 32R at 19 inches wide, 3.5 inches high, two rack spaces, and 12 inches deep, weighing 11.2 pounds and drawing 35 watts, with an ambient temperature ceiling up to 40 degrees Celsius. Every rack below was read against those five figures on a maker page or spec sheet.
Three rack figures decide the fit. Rack units decide the budget: the mixer takes 2U, and a working rig usually adds a power conditioner, a network switch or wireless receivers and a drawer. Usable depth decides whether the 12 inch chassis plus its rear connectors and cable bend fit inside with the lid on. Case weight and load capacity decide what the loaded rack asks of the person carrying it or the floor under it.
The six split into three formats. Three are molded or plywood road cases for a mixer that travels, one is a waterproof fly case with a removable cage, and two are studio furniture pieces, a freestanding rack and a rolling cabinet, for rooms where the mixer lives permanently beside the desk.
Studio rack to go with presonus mixers: the six racks in detail
Six racks follow, from the smallest road case to the studio furniture. Each section states who the rack suits, the maker figures behind it, and how it answers the mixer’s printed dimensions. Prices are not stated anywhere in this guide, and rack prices vary too widely by region to summarize fairly.
Gator G-PRO-4U-19
The G-PRO-4U-19 is the compact road answer: a rotationally molded polyethylene case with 4U of space and a 19 inch rackable depth. In PreSonus terms, 4U holds the 2U mixer and a 1U power conditioner with a spare space for a blank or a vent panel, and 19 inches of depth swallows the 12 inch chassis and its rear cabling without argument.
Gator’s spec sheet lists a case weight of 12 pounds, interior dimensions of 17 by 19 by 7 inches and exterior dimensions of 21.5 by 21.25 by 10 inches. The case carries full-size front and rear lids, threaded front and rear rack rails, molded-in ergonomic side carry handles and recessed steel twist latches. It is made in the USA from recycled materials, which the maker prints on the sheet.
The loaded math is friendly: 12 pounds of case plus the 11.2 pound mixer plus a conditioner stays an easy one-person lift. The limits are printed on the same sheet: the latches are not lockable, and 4U is a hard ceiling. A rig that plans to add wireless receivers or an EarMix network hub next season should start with a 6U case instead of replacing this one.
Pros: lightest road case here; deep 19 inch rackable space; front and rear rails for rear-mounted power; full lids both ends. Cons: 4U ceiling; latches do not lock. Buy if the rig is mixer plus power and travels in a car. Skip if the system is still growing.
Gator GR-6L
The GR-6L is the growth-room road case: 6U of space, a 19.25 inch rackable depth and locking latches, in a lightweight polyethylene shell that weighs 14 pounds. Six spaces hold the 2U StudioLive, a power conditioner, a network switch or stagebox hub and a drawer, which is the shape most small PreSonus rigs eventually take.
The maker spec sheet lists interior dimensions of 16.5 by 19 by 10.5 inches and exterior dimensions of 22.75 by 21.5 by 13 inches. The rack rails are threaded, field replaceable 7mm zinc-plated steel, fitted front and rear, and the lid carries a gasket. Four twist latches close the case, two recessed side handles carry it, and the sheet marks the case ATA accepted and lockable.
Field replaceable rails are the quiet professional feature: a stripped rail thread on a molded case usually ends the case, while here the rail itself swaps out. The trade against the G-PRO is construction style rather than size; the GR shell is the maker’s lightweight line, where the Pro series is the heavier roto molded line, and the sheet’s own figures show the 6U GR weighing just 2 pounds more than the 4U Pro case.
Pros: 6U with the deepest rackable figure here; locking latches and a gasketed lid; replaceable rails; still light at 14 pounds. Cons: lightweight shell line; handles are recessed grips rather than molded carry handles. Buy if the rig travels weekly and will grow. Skip if the case will be checked as freight every week.
SKB 3i-2317M146U Fly Rack
The SKB fly rack is the weather and airline answer: a 6U removable rack cage carried inside a waterproof injection molded utility case of polypropylene copolymer resin, closed by TSA-approved trigger-release latches. The cage lifts out of the case, so the mixer rig can work on a table or in a house rack and fly again the next day.
The listing gives a 13 inch rack depth for the cage and describes the case as waterproof with a pressure equalization design, in the maker’s iSeries pattern of gasket-sealed, submersible-rated shells. Six spaces match the GR-6L’s budget: mixer, power, networking and a spare space or drawer, all inside a case built for checked baggage handling and wet load-ins.
The depth figure needs honest arithmetic. PreSonus prints the 32R chassis at 12 inches deep; SKB prints 13 inches of rack depth. One inch remains behind the chassis for every rear connector, XLR, Ethernet and power alike, which in practice means short, flexible cables dressed sideways, or mounting the mixer in the cage only for transport and working it on the cage’s own footprint. Buyers who patch and unpatch nightly should read the two deeper Gator cases first.
Pros: watertight sealed case for fly dates; removable cage works outside the case; TSA latches for air travel; 6U budget. Cons: 13 inch depth is the tightest here; the case is the heavy way to carry 6U. Buy if the mixer flies or works outdoor stages. Skip if rear patching happens every show.
Gator G-TOUR EFX6
The G-TOUR EFX6 is the traditional flight case answer: 6U built from 9mm plywood with a laminated exterior, reinforced ball corners and commercial grade plated hardware. For a PreSonus rig that rides in a truck or trailer with the rest of the production, this is the construction style the rest of the truck is already built from.
The listing lists a 15 inch depth, front and rear rack rails 3.2mm thick, red recessed twist latches, spring-loaded handles with rubber grips, and a tongue and groove extrusion aluminum valance where the lids meet the body. Fifteen inches of depth clears the mixer’s 12 inch chassis with 3 inches for connectors, workable for a fixed install inside the case where cables stay dressed.
Plywood flight construction trades weight for repairability and crush strength; the listing does not print a case weight, and that gap is noted here rather than filled from other Gator models. The shallow 15 inch depth also means the rear lid is part of the cable plan: deep connectors and a power supply brick behind the mixer will not fit where the 19 inch molded cases give room to spare.
Pros: ATA-style plywood construction with ball corners; thick 3.2mm rails front and rear; spring-loaded gripped handles; 6U budget. Cons: 15 inch depth limits rear dressing; case weight not printed on the opened listing. Buy if the rig tours by truck with other flight cases. Skip if the case must be carried far by hand.
Middle Atlantic BRK12
The BRK12 is the studio furniture answer: a freestanding 12U rack in black MDF panels, built for a room rather than a road. Twelve spaces change the planning completely: the 2U mixer, power conditioning, an AVB network switch, wireless receivers, a patchbay and a drawer all fit in one column beside the desk, with spaces left over.
The maker’s datasheet lists a maximum weight capacity of 90.7 kilograms, about 200 pounds, an inner depth of 44.2 centimeters, about 17.4 inches, and an inner height of 53.3 centimeters. Exterior dimensions are 518 millimeters wide, 455 deep and 571 high, roughly 20.4 by 17.9 by 22.5 inches, and the rack ships with its mounting screws included. Side panels are fixed rather than removable, per the same datasheet.
Seventeen inches of inner depth answers the mixer’s 12 inch chassis with room for rear cabling that stays dressed permanently, which is the studio pattern: patch once, label everything, close the door on the mess. The 200 pound capacity is far beyond any mixer rig’s weight. The limit is the format itself: an MDF furniture rack is assembled in the room and does not travel, and fixed side panels mean rear access is planned from the front or by leaving space behind the rack.
Pros: 12U of space ends the space budget problem; 200 pound printed capacity; deep 17.4 inch interior; furniture finish suits a studio. Cons: does not travel; side panels are not removable; MDF construction. Buy if the mixer lives in one room. Skip if the rig leaves the building.
On-Stage WSR7500RB
The WSR7500RB is the rolling cabinet answer, designed as the rack companion to the maker’s WS7500 workstation: a laminated wood and steel cabinet on four casters, two of them locking, that parks beside or under the desk edge and rolls out when the rear panels need attention.
The maker’s catalog lists dimensions of 30 by 23.8 inches, a height of 30.5 inches with the casters fitted, and a height adjustment on feet of 29 to 30 inches, in black or rosewood finishes to match the workstation line. That 30.5 inch working height puts a rack mixer’s connections at seated desk height, which suits a StudioLive used as a studio interface as much as a live mixer.
The honest limit is documentation: the catalog entry prints exterior dimensions and caster details but no rack-space count and no load capacity, and those figures are not filled in here from other sources. A buyer who needs the exact usable spaces should confirm them with the maker before ordering. What the catalog does establish, construction, casters, footprint and finish matching, is exactly the set of facts a workstation buyer is choosing on.
Pros: rolls for rear access, then locks in place; height matches a workstation desk; finishes match the WS7500 desk line; laminated wood and steel construction. Cons: rack-space count and load capacity not printed in the maker’s catalog; furniture format only. Buy to complete a WS7500 workstation setup. Skip if the rack must be specified by the unit count alone.
Buying guide
Four decisions shape the pick: how many rack units the whole PreSonus system needs, whether the usable depth clears the mixer’s chassis and its cables, which format matches how the rig moves, and how the rack handles heat and weight. The sections below take each in turn.
Budget the units for the whole system
Start the count with the mixer itself: PreSonus prints the StudioLive 32R and SE 32R at 3.5 inches high, two rack spaces. Then count the companions a working system collects: a power conditioner at 1U, an AVB network switch at 1U, wireless microphone receivers at 1U or 2U, and a drawer at 1U or 2U for the router, cables and headphones.
That arithmetic is why 4U cases suit a mixer-and-power rig and 6U is the working minimum for a system, while the 12U furniture rack removes the ceiling entirely. Buying exactly today’s count is the classic mistake: rack systems grow by one unit at a time, and the case bought with two spare spaces is the one still in service three years later.
Do the depth arithmetic for a studio rack to go with presonus mixers
Depth is where racks fail on paper. PreSonus prints a 12 inch chassis depth. Behind that chassis sit combo XLR and TRS connectors, an Ethernet cable for AVB networking and an IEC power cord, each needing its own bend space before the rear lid closes. Compare the rack maker’s printed usable depth against 12 inches plus the cabling you actually run.
The figures in this guide span the range: 13 inches in the SKB cage, 15 in the plywood case, 17.4 inside the furniture rack and just over 19 in the two molded Gator cases. A fixed install, where cables are dressed once and stay, tolerates the shallow end. A rig patched nightly wants the deep end, where a hand can still reach a connector with the lid off.
Road case, fly case or furniture
Format follows the calendar. A mixer that travels in a car to weekend shows wants a molded case with lids, light to carry loaded: the two Gator molded cases weigh 12 and 14 pounds empty. A flying or outdoor mixer wants the sealed SKB shell and its removable cage. A mixer in a truck pack wants plywood and ball corners matching the other cases.
A mixer that never leaves the studio wants furniture: the BRK12’s 12U column or the rolling On-Stage cabinet beside the desk. Furniture racks trade lids and handles for capacity, depth and a finish that belongs in the room, and they ask nothing of a vehicle. Choose by where the mixer spends its nights, not its best days.
Heat, vents and the mixer’s ambient limit
PreSonus prints a recommended ambient operating temperature of 0 to 40 degrees Celsius for the SE 32R, and a continuous power consumption of 35 watts. A closed case in a hot room or a sunlit stage can push the air around the mixer past that ceiling, which is why working racks leave a vent space above a mixer rather than packing every unit tight.
Plan the layout with heat in mind: the mixer low in the case where air is coolest, a vented blank above it, and power supplies, which make their own heat, given their own space. Furniture racks in air-conditioned studios rarely trouble the limit; sealed fly cases opened only at showtime deserve the most care, and the removable SKB cage exists partly to solve exactly this.
Weight: case, mixer and everything after
Add the column before lifting: case weight, plus the mixer’s 11.2 pounds, plus each companion unit, plus the cables in the case. The molded cases stay friendly: 12 or 14 pounds of case against the same again in gear. The furniture rack inverts the question: its 200 pound capacity means the floor and the casters, not the rack, set the limit.
Where a maker does not print a figure, this guide says so: the plywood case’s weight and the rolling cabinet’s capacity are both unprinted in the sources opened here. Treat an unprinted figure as a question for the maker, not as a detail to assume, because the loaded carry is where an optimistic guess gets felt.
FAQ
Five questions come up whenever a StudioLive rack mixer needs a home: how many spaces the mixer takes, whether a shallow case can work, what else belongs in the rack, whether the mixer can stay cabled in transit, and which format a studio should choose. Each answer stays with the maker figures.
How many rack spaces does a PreSonus StudioLive rack mixer take?
Two. PreSonus prints the StudioLive 32R and SE 32R at 3.5 inches high and 19 inches wide, which is the standard 2U rackmount format, and the maker describes the 32R as a 40-channel mixer in two rackspaces. Any standard 19 inch rack in this guide mounts it; the buying question is how many additional spaces the rest of the system needs.
Will a shallow rack case fit a studio rack to go with presonus mixers setup?
Only with the depth arithmetic done. The mixer chassis is 12 inches deep, so a 13 inch rack depth leaves one inch per rear connector, and a 15 inch depth leaves three. Shallow cases work for a fixed layout with short dressed cables; they frustrate nightly patching. The rack’s usable depth, not its exterior depth, is the figure to compare.
What else should share the rack with the mixer?
The usual companions are a 1U power conditioner feeding every unit, a network switch for the AVB connections PreSonus builds the system around, wireless receivers, and a drawer for the control router and cables. That is how a 2U mixer becomes a 6U system, and why the unit budget in the buying guide counts the system rather than the mixer alone.
Can the mixer stay connected inside the case?
In the deeper cases, yes: with 19 inches of rackable depth there is room for the chassis, its connectors and a dressed cable loom behind it, and the rear lid closes over the loom. In the 13 inch fly cage the answer is transport with short cables, or unpatch and let the cage do its carrying job. Match the habit to the depth figure.
Is a furniture rack or a road case better for a home studio?
Furniture, if the mixer lives there. The BRK12 offers 12U, a 200 pound capacity and a 17.4 inch interior at a fixed address, and the On-Stage cabinet adds casters and a desk-matched height. A road case earns its lids and handles only when the mixer travels; in a spare room those lids mostly store dust while the 4U or 6U ceiling starts to pinch.
Conclusion
For most StudioLive owners the GR-6L is the balanced pick: 6U, the deepest rackable figure here, locking latches and a light shell, with spaces to spare. Take the BRK12 when the mixer stays in the studio, the SKB when it flies, and size every rack by the whole system, the mixer plus the units it will gather.