Updated Nov 16, 2026· 16 min read

Key takeaways

  • Compare six grills for charring steaks, from 1,500 degree overhead broilers to infrared sear burners and a hybrid charcoal grill reaching 1,200 degrees fast.

Why grills for charring steaks run hotter than standard burners

A hard char forms when intense heat reaches the steak surface faster than the interior cooks through, and the grills for charring steaks in this guide reach that intensity in three ways: overhead infrared broilers rated above 1,500 degrees, radiant infrared grates, and one hybrid firebox that burns charcoal to 1,200 degrees.

A standard gas burner heats air under a grate, and much of that heat moves past the food. The designs here shorten the path between the heat source and the meat. Overhead broilers put the burner directly above the steak, radiant panels turn burner output into infrared energy at the grate, and a charcoal drawer adds fuel heat on top of gas heat. Each maker documents the approach differently, so the sections below stick to the figures each maker or manual states: burner ratings, stated temperature ranges, cooking surface sizes, and the rack systems that control distance from the heat.

Grills for charring steaks at a glance

The table below lines up the six grills by heat source, the top heat figure stated for each one, and the cooking surface it works over. Broiler figures are burner or measured range tops, the hybrid figure is its charcoal range top, and the built-in figure is combined burner output, since its maker rates power in BTU rather than degrees.

Model Heat source Top heat figure Cooking surface
Otto Wilde Otto Grill Original Two overhead infrared burners 1,500 degrees F range top 12.5 x 10 inch grate
Northfire Inferno Single overhead infrared burner Burner rated over 1,500 degrees F 6 x 11 inch grill plate
Beefer Grill Single overhead infrared burner Burner rated over 1,500 degrees F Two grill grates, six positions
TEC Cherokee FR Radiant glass infrared panel 200 to 900 degrees F line range 212 square inches
Kalamazoo K500HB Hybrid Fire Gas burners plus charcoal drawer 1,200 degrees F on charcoal 506 square inches
Sedona by Lynx L500PS ProSear infrared burner plus tube burner 46,000 BTU combined 733 square inches total

Three formats emerge from the table. The Otto, Inferno and Beefer are countertop broilers built around a single cooking level under an overhead burner. The Cherokee FR is a portable infrared grill that carries its radiant panel anywhere a propane cylinder fits. The Kalamazoo and the Sedona are full-size installations, one hybrid and one built-in, that add charring heat to a complete grilling surface rather than replacing it.

Otto Wilde Otto Grill Original

The Otto Grill Original is an outdoor salamander broiler whose two overhead infrared burners were measured across a 450 to 1,500 degree range in review testing, with the burners firing down onto an enamel coated cast iron grate that measures 12.5 by 10 inches and adjusts through five height settings on a side lever.

Heat comes from above, so drippings fall away from the burners instead of onto them, and the review notes that this layout removes flare-ups from below entirely. Each burner carries its own piezoelectric igniter and its own control knob with settings from high to low, so one side can run lower than the other for mixed loads. The grate and a stainless steel drip tray ride on the same height frame, which keeps the tray under the food at every setting, and a second flat tray at the bottom catches drippings when the grate slides out for flipping.

The maker’s own recipe idea in the review shows the working pace: preheat both burners on high for three minutes, cook at the highest height setting for about one minute per side, then drop the grate to the lowest setting with the burners on low for about two and a half minutes per side, pulling the steak at about 130 degrees internal. The unit measures 16.7 inches wide, 17.3 inches deep and 11.6 inches high, and weighs just under 40 pounds, so it sits on a counter or sturdy table rather than a cart.

Otto Grill Original specifications

The specification list for the Otto Grill Original covers its two 9,000 BTU overhead infrared burners, the 450 to 1,500 degree measured range, the 12.5 by 10 inch enamel coated cast iron grate, five Meat-O-Meter height settings, dual piezoelectric igniters, and a stainless steel body at 16.7 by 17.3 by 11.6 inches.

  • Burners: two overhead infrared burners, 9,000 BTU each
  • Measured temperature range: 450 to 1,500 degrees F
  • Grate: enamel coated cast iron, 12.5 x 10 inches, five height settings
  • Ignition: piezoelectric igniter per burner
  • Dimensions: 16.7 W x 17.3 D x 11.6 H inches; just under 40 pounds
  • Extras: stainless steel drip tray with tongs; optional stainless rod grates

One handling note from the review: the cooking rack does not rest on rails, so the lever stays in hand while the grate is out, and the maker sells a sliding shelf with rollers as an add-on. The maker also recommends removing the cast iron grate during warm-up when an all-over sear matters more than grate marks.

Northfire Inferno

The Northfire Inferno is a single burner propane infrared broiler in a body 10 inches wide, 17 inches high and 14 inches deep, with a 6 by 11 inch grill plate, a seven notch rack that sets the food’s distance from the burner, and a stated burner temperature above 1,500 degrees.

The notch system is the heat control. The first four notches hold the grate closest to the burner and are the sear and char positions; the lower three notches roast and grill with less intensity. An internal frame carries the grates and slides in and out of the body, so food loads outside the hot box and slides in. In one comparison test program, an infrared camera measured the Inferno’s maximum at 1,686 degrees, the highest reading of the three broilers in that test, with heat strongest toward the rear of the grill plate.

The package centers on the plate and its trays: a drip tray half an inch deep and a food tray seven eighths of an inch deep sit under the cooking level, and the propane hose runs 39.5 inches. Like the other notch broilers, moving the grate between levels mid-cook takes care, since rendered fat rides on the grate as it comes out.

Northfire Inferno specifications

The specification list for the Northfire Inferno covers its single propane infrared burner rated above 1,500 degrees, the 6 by 11 inch grill plate, seven rack notches with the top four intended for hard searing and charring, the half inch drip tray, and a body measuring 10 by 17 by 14 inches.

  • Burner: single propane infrared burner, rated over 1,500 degrees F
  • Grill plate: 6 x 11 inches
  • Height control: seven rack notches
  • Trays: drip tray 1/2 inch deep; food tray 7/8 inch deep
  • Dimensions: 10 W x 17 H x 14 D inches
  • Hose: 39.5 inch propane hose

The Inferno suits a cook who chars one or two steaks at a time and wants the simplest control set in this guide: one burner, one knob, and seven fixed distances. Its plate is the smallest surface here.

Beefer Grill

The Beefer Grill is the original single burner overhead broiler in this group, with a burner temperature rated above 1,500 degrees, a nominal heat capacity of 3.5 kilowatts, six grate positions running from directly under the burner to about four inches below it, and a 35 pound stainless body.

Six positions cover the working range: the top slots put the steak surface within direct range of the burner for the hardest char, and each lower slot backs the food away for finishing or for thinner items. The delivery includes two grill grates and two Gastronorm drip trays, so juices collect under the cooking level and can hold vegetables alongside. In the same comparison test that measured the Inferno, an infrared camera read the Beefer’s maximum at 1,557 degrees, with the heat concentrated toward the back left of the grate.

The body measures 9.1 inches wide, 15.7 inches high and 18.6 inches deep, the deepest footprint of the three broilers, and the gas hose runs one meter. All grates, trays and shelving remove for cleaning. The ignition sits at the rear of the unit, which the test program found awkward to use while watching the cooking chamber.

Beefer Grill specifications

The specification list for the Beefer Grill covers its single overhead infrared burner rated above 1,500 degrees, a nominal heat capacity of 3.5 kilowatts, six grate positions spanning from directly under the burner to about four inches below, two included grill grates and drip trays, and a 35 pound body.

  • Burner: single overhead infrared burner, rated over 1,500 degrees F
  • Nominal heat capacity: 3.5 kW
  • Grate positions: six, from directly under the burner to about 4 inches below
  • Included: two grill grates, two Gastronorm drip trays, handle, glove
  • Dimensions: 9.1 W x 15.7 H x 18.6 D inches; 35 pounds
  • Gas hose: 1.0 meter

Between the two single burner broilers, the Beefer trades the Inferno’s seventh notch for a second grate and deeper trays, and its six positions start closer to the burner. Both cook one level at a time, so throughput comes from the short cooking times at the top positions rather than from surface area.

TEC Cherokee FR

The TEC Cherokee FR takes the opposite layout from the broilers: a single burner under a radiant glass panel cooks with 100 percent infrared energy across 212 square inches, in a portable body 23 inches wide and 28 pounds that runs on a 16.4 ounce cylinder or a 20 pound tank.

TEC’s infrared system puts the burner below a glass emitter panel, and the cooking grid sits directly on the panel, so heat arrives as radiant energy rather than as hot air moving past the food. The maker describes the result as even heat with no flare-ups, and the line’s stated temperature settings run from 200 to 900 degrees. That top figure sits well below the broilers’ 1,500 degrees, but it is delivered across the full grid at once, which suits charring several steaks in one batch instead of one or two at a time.

The cooking grid is 304 stainless steel, ignition is electronic, and the grill ships with a propane hose and regulator. The cooking surface is self-cleaning at high heat per the maker’s description, and the debris tray removes completely for emptying. At 28 pounds with no stand required, the Cherokee FR is the only grill in this guide that travels to a tailgate or campsite as readily as it sits on a patio table.

TEC Cherokee FR specifications

The specification list for the TEC Cherokee FR covers its 212 square inch cooking surface, a single burner rated at 13,500 BTU under a radiant glass panel, a 304 stainless steel cooking grid, electronic ignition, dual fuel supply from a small cylinder or a 20 pound tank, and a 28 pound body.

  • Cooking surface: 212 square inches
  • Burner: single infrared burner, 13,500 BTU, radiant glass panel
  • Temperature range: 200 to 900 degrees F (TEC line range)
  • Grid: 304 stainless steel
  • Ignition: electronic
  • Fuel: 16.4 ounce propane cylinder or 20 pound tank; hose and regulator included
  • Size and weight: 23 inches wide; 28 pounds

The Cherokee’s char comes from sustained radiant contact rather than a short blast, so thick steaks get more working time per side than the broilers allow.

Kalamazoo K500HB Hybrid Fire Grill

The Kalamazoo K500HB is a 28 inch built-in hybrid grill whose two cast brass Dragon Burners total 55,000 BTU on natural gas, whose gas fired range runs from 250 degrees to more than 700 degrees for searing, and whose charcoal drawer extends the range to 1,200 degrees.

The Hybrid Fire drawer sits above the burners and below the 23 by 22 inch grilling surface. Leave it empty and the grill cooks on gas alone. Load it with charcoal or wood and the burners light the fuel and can keep it going, which is how the temperature range stretches from 150 degrees at the low end to 1,200 degrees at the top. The maker rates the firebox at more than 100 BTU per square inch of cooking power across its 506 square inches of primary surface, and each Dragon Burner weighs more than 13 pounds on its own.

Supporting systems match the scale: a dedicated ignition burner with electronic hot surface ignition lights the mains, a rotisserie system with an infrared burner mounts its motor inside the cabinet, and a flip-up warming rack adds a second level. Ash, grease and debris funnel down to a deep cleanout pan, and a variable hood vent controls air flow for charcoal and wood cooking. The body is 304 stainless steel throughout.

Kalamazoo K500HB specifications

The specification list for the Kalamazoo K500HB covers its two cast brass Dragon Burners totaling 55,000 BTU on natural gas or 48,500 on propane, a 506 square inch primary surface, a gas range topping above 700 degrees, a charcoal range reaching 1,200 degrees, and an infrared rotisserie burner.

  • Primary surface: 506 square inches (23 x 22 inches)
  • Main burners: two cast brass Dragon Burners, 55,000 BTU total NG / 48,500 LP
  • Total output: 73,300 BTU NG / 66,100 BTU LP
  • Temperature range: 250 to over 700 degrees F on gas; 150 to 1,200 degrees F on charcoal
  • Fuel system: Hybrid Fire drawer for charcoal and wood over gas burners
  • Ignition: ignition burner with electronic hot surface ignition
  • Extras: rotisserie system with infrared burner; flip-up warming rack; deep cleanout pan

The K500HB is the only grill here that chars with live charcoal while keeping gas ignition and gas backup under the same hood. Its 1,200 degree charcoal top end lands between the infrared grills and the overhead broilers, across a full-size surface.

Sedona by Lynx L500PS

The Sedona by Lynx L500PS is a 30 inch built-in grill that pairs one ProSear infrared burner with one stainless steel tube burner for up to 46,000 BTU combined, spreading the cooking across 733 square inches of surface, 508 primary and 225 secondary.

The ProSear burner is the charring tool: an infrared burner on one side of the grill that answers with intensive heat for steak surfaces, while the tube burner side handles general grilling. Ceramic radiant briquettes sit in the system to even out the heat, and the grilling grates are stainless steel. The maker describes the ProSear as fully variable rather than a fixed high setting, so the same burner can run lower for fish or vegetables once the steaks are done.

Controls and fittings suit a permanent island: direct spark ignition with battery backup, dual halogen surface lights, blue lit control knobs, a temperature gauge, and the Lynx Hood Assist with a fluid rotation handle for the heavy hood. The welded construction leaves no gaps where grease can collect, and the cut-out measures 29 inches wide, 10 inches high and 21.25 inches deep. The grill ships from the factory in liquid propane or natural gas.

Sedona by Lynx L500PS specifications

The specification list for the Sedona by Lynx L500PS covers its ProSear infrared burner and stainless steel tube burner combining for up to 46,000 BTU, 733 square inches of total cooking surface, ceramic radiant briquettes, stainless steel grates, direct spark ignition with battery backup, and a 29 inch cut-out.

  • Burners: one ProSear infrared burner (23,000 BTU) and one stainless steel burner (23,000 BTU), up to 46,000 BTU combined
  • Cooking surface: 733 square inches total (508 primary, 225 secondary)
  • Heat distribution: ceramic radiant briquettes
  • Grates: stainless steel
  • Ignition: direct spark with battery backup
  • Features: dual halogen surface lights; temperature gauge; Hood Assist; blue lit knobs
  • Cut-out: 29 W x 10 H x 21.25 D inches; ships in LP or NG

The Sedona fits a cook who wants a dedicated sear zone inside a conventional built-in rather than a separate appliance. Half the grill chars at infrared intensity while the other half roasts, warms or holds.

Overhead heat versus grate-level infrared

The three overhead broilers and the three grate-level designs char differently: broiler burners fire down onto the steak from inches away, while radiant panels and sear burners push infrared energy up through a grate, and the difference shows in capacity, in how drippings behave, and in how much of the surface chars at once.

Overhead heat browns the top surface evenly because nothing sits between the burner and the meat, and drippings fall into a tray instead of onto a burner, so there is no flare-up from below. The trade is capacity: a broiler cooks one level of food, sized here between a 6 by 11 inch plate and a 12.5 by 10 inch grate. Grate-level infrared keeps the familiar grill layout, so the Cherokee FR chars across 212 square inches, the Sedona across a 508 square inch primary surface, and the Kalamazoo across 506 square inches with charcoal in the drawer.

Distance is the second heat control

Every grill in this guide pairs its heat source with a distance or output control: the Otto’s lever runs five height settings, the Inferno offers seven notches, the Beefer six positions, and the infrared and hybrid grills throttle burner output, which makes positioning as much a part of charring as the top temperature figure.

The broiler makers build their guidance around that control. Otto’s recipe idea sears at the highest setting for about a minute per side, then finishes at the lowest setting with the burners low. The Inferno reserves its top four notches for hard sear and char work and its lower three for roasting. On the grate-level side, the ProSear burner varies its output across a range instead of offering one fixed sear setting, and the Kalamazoo varies both burner output and the charcoal bed itself.

Preheat times and cooking pace

Charring heat arrives on different clocks across this guide: the Otto maker’s recipe preheats for three minutes, the infrared broiler class generally preheats in about ten minutes, and TEC’s infrared grills heat in about ten minutes as well, while a charcoal load in the Kalamazoo drawer builds on its own schedule.

Cooking pace follows the same split. At the Otto’s top setting, a steak side takes about a minute, and the full recipe runs about eight minutes from preheat to a 130 degree internal reading. The full-size grills trade that speed for batch size: a 506 or 733 square inch surface chars many steaks per load, each on a conventional per-side timing.

What the manuals and makers time a steak at

The clearest timing statement in this guide comes from the Otto maker’s recipe idea: three minutes of preheat on high, about one minute per side at the highest grate setting, then about two and a half minutes per side at the lowest setting with the burners on low, removing the steak at about 130 degrees internal.

Thin foods change the math on every model: the Otto review notes that thin skirt steaks, fish fillets and shrimp cook through in moments at broiler heat. On the grate-level grills, TEC’s range down to 200 degrees and the Kalamazoo’s gas range down to 250 degrees let the same unit slow down for delicate items after the charring is done, which the fixed-format broilers handle by distance instead.

Buying guide: choosing grills for charring steaks

Choosing among grills for charring steaks starts with format: a countertop broiler for one or two steaks at the highest heat, a portable infrared grill for full batches away from home, or a built-in or hybrid installation that adds charring power to a complete outdoor kitchen surface.

Then weigh the heat evidence. Burner temperature ratings above 1,500 degrees describe the burner itself on the Inferno and the Beefer; the Otto’s 450 to 1,500 degree range was measured across its cooking chamber in review testing; TEC states a 200 to 900 degree range for its infrared line; and the Kalamazoo separates its gas range, topping above 700 degrees, from its 1,200 degree charcoal range. The Sedona’s maker rates power in BTU instead, up to 46,000 combined.

Capacity and fuel close the decision. Broiler plates and grates run from 66 to 125 square inches; the Cherokee FR offers 212; the built-ins offer 506 and 733.

Fuel, placement and format checks

Placement rules differ by format: the countertop broilers need a sturdy, heat tolerant surface with room to slide a grate out at full height, the Cherokee FR needs only a tabletop and a cylinder, and the Kalamazoo and Sedona need built-in installations with gas lines, clearances, and electrical supply for ignition and lighting.

Check the details that follow the format. The Kalamazoo is not for use on recreational vehicles or boats and needs six inches of clearance from combustibles at the sides and back. The Sedona needs a 120 volt outlet within reach of the cut-out for its lights and ignition. The broilers need headroom above the unit, since the heat source sits at the top of an open chamber and the grate slides out toward the cook.

The right pick is the one whose heat figure, capacity and installation match the cooking actually planned: nightly two-steak charring points to a broiler, weekend batches to the infrared portable or a built-in sear zone, and charcoal flavor at high heat to the hybrid drawer.

Charring a steak is a short, violent bit of cooking, and these six grills deliver it six ways: overhead burners above 1,500 degrees, a radiant glass panel at 900, a charcoal drawer at 1,200, and an infrared sear burner inside a full-size built-in. Match the format to the batch size and the heat evidence to the claim, and the crust follows.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.