Key takeaways
- Heat tents, an igniter kit, a regulator and hose, a lid thermometer and a grease tray: the replacment parts for gas grills that wear out first, with fitment.
Most gas grills do not die all at once; they fail one part at a time, and the best replacment parts for gas grills below cover the five failures owners meet most: rusted heat tents, a dead igniter, a tired regulator, a fogged lid thermometer and a grease tray that has rusted through. Each entry lists the sizes and fitment its maker states.
The Short List: Replacment Parts for Gas Grills
These five parts sit in five different systems of the grill, so the short list works as a diagnostic map as well as a shopping list. Find the symptom your grill shows, and the matching part is the one to measure, match by part number and replace before the next cook.
| Part | System | Key stated spec | Stated fitment |
|---|---|---|---|
| Terefour Adjustable Heat Plate Shield, 4-Pack | Heat management | Stainless steel, extends 11.75 to 21 inches | Listed Charbroil and Brinkmann models |
| Ignition Spark Kit with Push Button Switch | Ignition | Universal spark generator, AA battery required | Char-Broil, Broil King, Kenmore, Coleman and more |
| 3 Feet Hose Regulator LP Conversion Kit | Gas flow | 3 foot hose, QCC1 / Type 1 connection | Gas BBQ grill models using QCC1 tanks |
| BBQ Temperature Gauge for Char-Broil Grills | Heat monitoring | 3 inch face, 1.6 inch stem | Long list of Char-Broil models |
| Outdoor Bazaar Universal Grease Tray | Grease management | Adjusts 24 to 27 inches, 15.5 inch width | 3, 4 and 5 burner grills, freestanding only |
None of these parts is universal in the loose sense. Each one fits a stated range: a length range, a connection type, a stem size or a list of model numbers. The detail sections give those ranges in full, because with replacement parts the range is the product, and a part bought outside its stated range is a part that goes back.
There is a second way to read the list: as the grill’s whole support system. The burners get the glory, but they only cook when gas reaches them through a sound regulator, when a spark lights them, when tents spread their heat and shield their ports, when a gauge reports the result, and when a tray carries the waste away. A failure in any one of the five makes the burners look guilty, which is why this article starts with the support parts rather than the burners themselves.
The Five Parts in Detail
Every entry below sticks to what its maker or listing states: what is in the box, what it is made of, the sizes that decide fit, and the models it is sold for. Where a maker leaves a figure unstated, the entry leaves it out too, and the buying notes further down explain how to work around the gap.
Terefour Adjustable Heat Plate Shield, 4-Pack
Heat tents, also sold as heat plates or flame tamers, sit over the burners and take the drippings, the flare-ups and the rust that would otherwise land on the burner tubes. This four-pack is stainless steel, and its length adjusts from 11.75 inches up to 21 inches, which is how one pack covers so many grills.
- Pack count: 4 heat plate shields
- Length: extends from 11.75 inches up to 21 inches
- Material: stainless steel
- Pack weight: 4 pounds
- Fits Charbroil models including 463230515, 463230514, 463230513, 463230512, 463230511, 463230510 and 463226514
- Also fits Brinkmann 810-2511-S, 810-3660-S, 810-1750-S and 810-4580-S
The adjustable length is the feature to use properly. Measure the tent that comes off your grill at its longest point, set the replacement to the same span, and it rests on the same ledges as the original. A tent set too short rocks and rattles; a tent forced too long bows upward into the grate. Set right, the pack renews the whole tent row in one job, which matters because tents in the same firebox rust at the same rate.
Stainless steel suits this part because the tent lives in the wettest spot in the grill, under the food and over the flame. The listing describes drippings vaporizing on the hot tent surface, which is the tent’s second job: it turns juices into the vapor that flavors the food while it shields the burner ports below from clogging drips.
Replace the full row at once when you can. Owners often swap only the worst tent and leave the rest, then repeat the job twice more in the following seasons as its neighbors fail. A four-pack ends that cycle: every tent starts the same age, sits at the same height, and spreads heat evenly across the firebox instead of leaving one tired, sagging tent to drip straight onto its burner.
Ignition Spark Kit with Push Button Switch
When a grill lights only with a match, the spark generator is usually the worn part. This kit pairs a universal spark generator with a push button switch, and the seller lists it against a wide spread of brands: Char-Broil, Broil King, Kenmore, Coleman, Cuisinart, Master Chef, Broil-Mate, Dyna-Glo, Ducane and more.
- Universal spark generator with push-button ignition switch
- Battery powered: AA battery required, not included
- Replaces OEM part numbers G651-1300-W1, 03333, 80009955 and G570-0021-W1
- Named fitment includes Brinkmann 810-8425-S and 810-9425-W, Coleman G53101 to G53104, Cuisinart G41801 and G41802, Outdoor Gourmet CG3023E
- One-year warranty stated by the seller
The part numbers are the fastest route to the right kit. Igniter modules look alike across brands, but the outlet count and the button mounting differ, so match the number on your old module or in your grill manual against the numbers this kit replaces. The seller also notes a version with one more outlet for owners who want the side burner on the same button, so count your burners before choosing.
Fit the battery check into the same job. A generator that clicks weakly or not at all often needs only its AA battery, and since the battery is not in the box, having one on hand decides whether the swap ends with a working igniter or a second trip. If the old module shows cracked housing or corroded terminals, replace the kit whole rather than nursing it along.
3 Feet Hose Regulator LP Conversion Kit, QCC1 / Type 1
Weak flames on every burner at once point away from the burners and toward the regulator, the part that meters gas from the tank to the manifold. This kit replaces regulator and hose together: a 3 foot hose with a QCC1, also called Type 1, tank connection, sold for gas BBQ grill models.
- Regulator and hose supplied as one kit
- Hose length: 3 feet
- Tank connection: QCC1 / Type 1
- Sold as a replacement regulator and hose for gas BBQ grill models
- One-year warranty stated by the seller
Replacing the two as a unit is the sound approach, because the hose ages with the regulator: rubber hardens, and the crimped joints at both ends are the spots that start to weep gas first. The QCC1 handwheel connection is the current standard tank fitting, so the first check is simply that your tank and grill use it, which nearly every propane grill built in recent decades does.
Length is the second check. Three feet suits the common cart grill layout, where the tank hangs on the cart beside or below the firebox. Measure your old hose along its run rather than in a straight line, and if the original was longer because the tank sits apart from the grill, match that length instead of pulling the tank closer to the heat.
Route the new hose the way the old one ran, clear of the firebox walls and the grease tray, with no sharp bends at the fittings. A hose that drapes against hot metal ages in a single season. Once fitted, the handwheel connection should thread on by hand alone; a QCC1 nut that needs a wrench is cross-threaded, and backing it off and starting again is the fix, not more force.
BBQ Temperature Gauge for Char-Broil Gas Grills
A lid thermometer that fogs, sticks or loses its needle leaves you grilling blind, and this gauge is the stated replacement for a long list of Char-Broil gas grills. Its face measures 3 inches across, large enough to read at a glance, on a stem of 1.6 inches that reaches into the lid’s heat.
- Dial face: 3 inches (7.6 cm)
- Stem: 1.6 inches (4 cm)
- Fits a long stated list of Char-Broil models, including 463448021 and the 463230510 to 463230515 group
- Replaces Char-Broil OEM part numbers including G517-8800-W1, G511-1700-W1A, 80004030, 80007690, 80016407 and 80016887
- One-year warranty stated by the seller
Two dimensions decide whether a gauge drops into your lid: the face diameter, which has to cover the hole and match the bezel, and the stem length, which has to reach past the lid’s inner skin into the cooking chamber air. The stated 3 inch face and 1.6 inch stem match the factory gauge on the listed models, so for those grills the swap is a nut off and a nut on.
If your Char-Broil is not on the model list, work from the part numbers instead. Lid gauges were shared across many grills and years, and the OEM numbers this gauge replaces, printed above, cover more grills than the model list alone suggests. Match either list and the gauge is the right one; match neither and keep looking, because a stem that sits short reads the lid metal more than the air.
A lid gauge reads the air at the top of the cooking chamber, which runs hotter than the grate below it, so treat the dial as a reference rather than a promise. Its real value is repeatability: once you know what the dial shows when the grill cooks the way you like, the same reading brings you back to the same fire, cook after cook, season after season.
Outdoor Bazaar Universal Grease Tray
The grease tray under the firebox rusts quietly until it holes through, and then every cook drips onto the cart and the patio. This replacement is built from 0.8-gauge steel with a zinc coating, arrives in three pieces, and adjusts from 24 to 27 inches long against a fixed width of 15.5 inches.
- Material: steel, 0.8-gauge thickness, zinc-coated
- Adjustable length: 24 to 27 inches; fixed width: 15.5 inches
- Weight: approximately 5 pounds
- In the box: grease pan in three pieces, 1 custom grease cup, 8 wing nuts and bolts
- Fits 3, 4 and 5 burner grills from Dyna Glo, Nexgrill, Kenmore, Expert Grill, Backyard Grill, BHG, Uniflame, Charbroil and others
- Freestanding grills only; the maker states it is not suitable for built-in models
The three-piece build is what makes the adjustment work: the middle section slides into the two outer sections, you set the overall length to match the old tray, and the wing nuts and bolts lock it there, with no tools needed for assembly. The sloped floor then channels grease toward the drain hole and into the included cup, which lifts out for emptying.
Measure before ordering, the way the manual directs: old tray out, length checked against the 24 to 27 inch range, width checked against 15.5 inches. A tray that is too narrow for its slot lets grease miss the cup entirely, which defeats the part. And note the freestanding limit: built-in grill heads use different tray rails, and this tray is not made for them.
How to Choose Replacment Parts for Gas Grills
Replacement parts reward a different habit than new-grill shopping. The grill itself has already made most of the decisions: its part numbers, its tray width, its tank connection. Your job is to read those decisions off the old part and buy the stated match, and three working rules cover almost every part in this article.
Start With the Part Number
Where a part carries a number, the number outranks every other clue. The igniter kit above replaces four named OEM numbers, the Char-Broil gauge replaces a list of them, and the heat tents name the grill models they fit. Grill makers reuse the same part across whole model families, so one number can confirm fit across years of production.
The number lives in three places: stamped or stickered on the old part itself, in the grill’s manual, or on the rating label inside the cabinet door or on the back of the grill. Photograph the label before you start; once the old part is in the trash, its number goes with it, and the next replacement starts from memory instead of evidence.
Keep the old part until the new one is fitted and working, even when it looks like scrap. The old igniter’s outlet count, the old tray’s width, the old gauge’s stem: each is a template the new part has to match, and comparing them side by side on the bench catches a wrong order before it becomes a fitted mistake. Only when the grill lights, heats and drains as it should does the old part leave the garage.
Measure the Part Coming Off
For parts sold on a range, the tape measure rules. The heat tents adjust from 11.75 to 21 inches, the grease tray from 24 to 27 inches against a fixed 15.5 inch width, and the gauge stem runs 1.6 inches. Every one of those ranges has edges, and a grill that falls outside the edge needs a different part, not a forced fit.
Measure the old part, not the hole it came from, and measure it at its extremes: full length, full width, and for anything with a stem or a probe, the depth it reaches. Rust shrinks and swells metal, so brush the measuring points clean first. Two minutes with a tape now beats a return, a second order and another weekend with the grill in pieces.
Match the Part to the Symptom
Each system in a gas grill fails with its own signature, and matching symptom to system keeps you from replacing good parts. One burner row out is a burner or a tent problem. Every burner weak at once is the regulator or the tank. No click at all is the igniter or its battery. A blind lid is the gauge. Grease under the cart is the tray or its cup.
Work the simple checks inside each system first: the igniter’s battery, the tray’s cup position, the tent that has slipped off its ledge. When the part itself is cracked, holed or corroded through, though, no adjustment brings it back, and the stated-fitment replacement in this article is the fix. Diagnosis first, then the part number, then the tape: in that order, the first part you order is usually the last one you need.
One caution belongs with the gas-side symptoms. Weak flames can also mean a nearly empty tank or a tank valve opened too fast, both of which sort themselves out without parts. Rule those out before the regulator comes off: swap in a known full tank, open its valve slowly, and light again. If the flames stand up, the regulator was never the problem, and the kit stays on the shelf for the day it truly is.
Fitting and Looking After the New Parts
None of the five parts needs more than household tools, and two of them, the grease tray and the heat tents, need none at all. The fitting notes below follow what the makers themselves print, and the care notes follow the same manuals, because a replacement part looked after the maker’s way lasts the way the maker intended.
Fitting Notes, Part by Part
The grease tray sets the pattern: the Outdoor Bazaar manual has you assemble the three sections, set the length, lock the wing nuts by hand, seat the cup under the drain hole, and slide the tray into its slot beneath the burners on a cool grill. The heat tents are simpler still, lifting out and dropping in once the grates are off.
- Igniter: match the outlet count to your burners, and have the AA battery ready, since it is not in the box
- Regulator and hose: work with the tank valve closed, thread the QCC1 handwheel on by hand, and leak test the joints before the first lighting
- Temperature gauge: the old gauge unscrews from its nut inside the lid; the new stem must pass through the same hole to its full 1.6 inch length
- Heat tents: set the length before the tent goes in, so it lands flat on its ledges
- Grease tray: confirm the cup sits under the drain hole after the tray slides home
The leak test after any gas-side work follows the routine printed in burner manuals: brush soapy water, half soap and half water, over the connections, open the tank valve, and watch for bubbles. Bubbles mean gas is escaping at that joint; close the valve, refit the joint, and test again until the film stays still. It takes two minutes and it is the whole proof that the gas path is sound.
Keeping the New Parts Working
The grease tray manual gives the care pattern for the whole group: empty the cup regularly, wash the tray with warm soapy water and a non-abrasive brush or sponge, and keep harsh chemicals off the zinc coating. A tray cleaned this way drains as designed; a tray left full overflows onto the new steel and starts the rust clock again.
Heat tents want a brush and a shake over a bin whenever ash and char build up, since a tent buried in debris stops vaporizing drippings and starts steaming them. The gauge wants nothing but a wiped face and a check against an oven thermometer once a season if you suspect it drifts. The igniter wants a dry battery compartment and a fresh AA when the clicks weaken. Small habits, applied to the parts that wear, are what keep a grill out of the parts catalog for years at a stretch.
Storage closes the loop. A grill put away clean, with its tray emptied and its tents brushed, starts the next season with the same parts it ended the last one. A grill put away dirty spends the winter rusting from the inside, and its owner spends the spring ordering from lists like this one. None of this asks much; these are simply the five places where a season of neglect shows first.
A gas grill is a frame, a firebox and a handful of wearing parts: tents that shield the burners, a spark that lights them, a regulator that feeds them, a gauge that reports the heat and a tray that carries the grease away. Match each by its stated number, size or range, fit it on a cool grill, and the machine cooks like the day it was assembled.