Key takeaways
- Compare replacement burners for gas grills: stainless tube sets, H burners and cast iron ring burners with stated lengths, materials and model fitment listed.
Yellow, lazy flames and cold patches across the grate trace back to a worn burner, and the best replacement burners for gas grills below put the firebox right without a new grill. Every pick lists the length, material and fitment its maker states, so matching one to the burner coming out of your grill is a measuring job, not a guessing game.
The Short List: Replacement Burners for Gas Grills
Five burners cover most of the shapes found under the grates of American gas grills: a model-specific tube set for Weber Spirit grills, an H burner kit with its own venturi tubes, a heavy cast iron ring burner, a stainless H burner head, and a four-pack of straight tubes for big-box brands.
| Burner | Type | Material | Key size | Stated fitment |
|---|---|---|---|---|
| Uniflasy Burner Tube Set (replaces Weber 69787) | 3 main tubes + crossover | 304 stainless steel | 18 in and 17-3/4 in mains, 15-1/4 in crossover | Weber Spirit 300 series, front controls |
| Char-Broil Burner Replacement Part G208-5200-W2 | H burner assembly kit | Not stated by the maker | Assembly weighs 1 pound | Grills built around burner part 463620415 |
| Music City Metals 29251 | Rectangular ring burner | Cast iron | 15.75 x 4.75 x 3 inches | Sam’s Grills, Bakers & Chefs, Grand Hall, Members Mark |
| Music City Metals 10502 | H-type twin burner head | Stainless steel | 15.875 x 8 x 2.06 inches | Arkla, Charmglow, Sunbeam |
| J&HYBBQ Burner Tubes, 4-Pack | Straight tubes | 304 stainless steel | 15 3/4 inches long | Charbroil, Nexgrill, Thermos, Bakers & Chefs, Coleman |
Read the table as a first filter, not a final answer. A burner only works when its length, its inlet position and its mounting points line up with the grill it is going into, and the detail sections below give the exact stated sizes and model lists to check against the burner already in your firebox before you order anything.
The Five Burners in Detail
Each entry below sticks to what its maker or listing states: shape, material, dimensions and the models it is sold for. Where a maker does not state a figure, the entry says so rather than filling the gap, because a burner bought on a guessed dimension is a burner that goes back in the box.
Uniflasy Burner Tube Set for Weber Spirit 300 Series
This set replaces the full burner layout of a Weber Spirit 300 series grill in one box: three main burner tubes plus the crossover tube that carries flame between them. The maker sells it as the replacement for Weber part 69787, and the stated sizes differ by position, which is exactly how the original layout is built.
- Left and right main burners: 18 inches long
- Center main burner: 17-3/4 inches long
- Crossover tube: 15-1/4 inches long
- Material: 304 stainless steel, noted by the maker as non-magnetic
- Fits Weber Spirit E-310, S-310, E-320, S-320, E-330, S-330 and SP-330 (2013-2017), plus Spirit II 300 series (2013-current)
- Front-mounted controls only; the maker states it does not fit side-control models
The position-specific lengths are the point of this set. Spirit fireboxes do not use three identical tubes, so a universal tube cut to one length cannot stand in for all three. If your Spirit has its control knobs on the front panel and falls in the stated year ranges, this is the most direct swap in the group, with every tube arriving at the length its position needs.
The front-control limit deserves a second look before ordering. Weber sold Spirit grills with side-mounted controls in earlier years, and the maker is plain that this set is not for them. Check where your knobs sit, confirm the model number against the stated list, and the set covers the whole burner system, crossover included, in a single purchase.
One more detail in the maker’s description is worth knowing: the tubes are 304 stainless steel and non-magnetic, which is why a magnet test will not confirm the grade on these the way it might on lesser alloys. Judge the set by its stated fitment and dimensions instead. Owners of the listed Spirit models get a burner system laid out exactly as the original, position by position, with no cutting, bending or adapting of tubes to make them reach the valves.
Char-Broil Burner Replacement Part G208-5200-W2
Some grills run a single wide H burner instead of separate tubes, and this kit is built for them. It contains one H-type burner assembly, the burner listed as part 463620415, and it arrives with the parts that connect it to the valves: two flexible venturi tubes and a bag of mounting hardware.
- One H-type burner assembly (part 463620415)
- 2 flexible venturi tubes included
- Mounting hardware included: screws, nuts, clips and washers
- Item weight: 1 pound
- Described by the maker as an authorized aftermarket product designed to meet the specifications of the original equipment manufacturer
Burner and venturi tubes age together, so a kit that replaces both at once solves the common problem of a new burner meeting old, cracked venturi tubes. The flexible tubes also forgive small differences in how the burner sits against the valve outlets, which matters on older fireboxes that have warped or shifted over years of heat cycles.
The maker does not state the burner material or its dimensions on the page, so this pick is a fitment buy rather than a dimension buy: it suits owners whose grill manual or old burner carries the 463620415 part number. If your grill uses that part, the kit restores the burner and its gas feed in one job instead of two separate orders.
The included hardware matters more than it looks. Old mounting screws and clips usually come out rusted or snap during removal, and a kit that ships with screws, nuts, clips and washers means the job does not stall halfway while you hunt for fasteners that match. At 1 pound for the whole assembly, it is also the lightest single-burner option here, which suits the smaller two-burner grills this H layout usually serves.
Music City Metals 29251 Rectangular Ring Cast Iron Burner
Older warehouse-club grills often hide a one-piece cast iron ring burner under the grates, and the 29251 is the current version of that part. It is a rectangular ring casting, heavy for its size, sold for a long list of Sam’s Grills, Bakers & Chefs, Grand Hall and Members Mark models.
- Material: cast iron
- Dimensions: 15.75 x 4.75 x 3 inches
- Weight: 6 pounds
- Shape: rectangular ring, one-piece casting
- Fitment: named models from Sam’s Grills, Bakers & Chefs, Grand Hall and Members Mark (full model lists in the maker’s manual)
At 6 pounds, this burner weighs three times as much as the stainless head further down the page, and that mass is the reason owners of these older grills look for the same part again: the casting holds heat and spreads it across the ring instead of concentrating it along a thin tube wall. Measure your old ring against the stated footprint before ordering, because these grills span many model years.
Cast iron asks for a little more care than stainless steel. It should be brushed clean and kept dry between cooks, since a casting left wet under a closed lid will rust on the surface. None of that changes the fitting job: the ring drops into the same mounts as the burner it replaces, and the maker’s model list is the authority on whether your grill is one of them.
Music City Metals 10502 Stainless Steel Burner Head
The 10502 is a burner head only: an H-type twin burner in stainless steel, sold without venturi tubes. That sounds like a drawback until you meet the grills it fits, older Arkla, Charmglow and Sunbeam models whose venturi tubes are often still sound while the burner head itself has burned through.
- Material: stainless steel
- Dimensions: 15.875 inches long x 8 inches wide x 2.06 inches high
- Gas inlets: 1.25 inches offset
- Weight: approximately 2 pounds
- Fits listed Arkla, Charmglow and Sunbeam models, including Arkla 3051KG, Charmglow 3541KG and Sunbeam 154410
- Designed for use with venturi models 70201, 70301, 70401, 708LR, 709LR, 71202 and others listed by the maker
The numbers that decide this part are the footprint and the inlet offset. The head spans 15.875 by 8 inches, and its gas inlets sit 1.25 inches off center, so the venturi tubes from the listed models land on the valve outlets without bending or forcing. If your grill is on the maker’s list and your venturi tubes are intact, this head is the smaller, lighter job.
Go in knowing the boundary of the box: venturi tubes are a separate part. If yours are cracked, holed or clogged beyond cleaning, order them at the same time using the maker’s venturi model list. The manual for this head also gives the working routine used in the fitting section below, from the soapy-water leak test to clearing ports with a stiff wire.
J&HYBBQ 15 3/4 Inch Burner Tubes, 4-Pack
Straight tube burners are the most common layout in big-box gas grills, and this four-pack covers the brands that use them most: the listing names Charbroil, Nexgrill, Thermos, Bakers & Chefs and Coleman. Each tube runs 15 3/4 inches, and the pack count matches the four-burner grills these brands sell in volume.
- Pack count: 4 burner tubes
- Tube length: 15 3/4 inches
- Material: 304 stainless steel
- Listing dimensions: 15.75 x 2.6 x 1.8 inches
- Listing notes precisely arranged burner holes for stable, even flames
A four-pack suits two situations. The first is a four-burner grill whose tubes have all aged together, which is the usual case, since tubes in the same firebox see the same heat and the same drippings. The second is a two- or three-burner grill where the pack leaves spares on the shelf for the next swap, years later, when the same tube length may be harder to find.
Because one tube length serves many models, the measuring step matters more here than with a model-specific set. Pull one old tube, measure its full length and look at how its end meets the valve, then compare against the stated 15 3/4 inches. If your tubes are a different length, this pack is not your part, whatever brand name is on the lid.
The listing also gives the tube dimensions as 15.75 x 2.6 x 1.8 inches, which helps when the old tube is too rusted to measure cleanly: compare the width and height of the tube profile as well as its length. Straight tubes are the simplest burner design in this group, with no crossover and no shared casting, so a grill that runs them is the easiest of all to keep in burners over a long life, as long as this common length stays in production.
How to Choose Replacement Burners for Gas Grills
Burner shopping goes wrong in predictable ways: the tube that is a half inch too long, the H burner bought for a grill that runs straight tubes, the set that fits every Spirit except the side-control years. Four checks, done with the old burner on a workbench, prevent nearly all of them.
Measure the Old Burner Before Ordering
Length is the first measurement and the one that rules out the most wrong parts. The burners above span a narrow band, from the 15 3/4 inch J&HYBBQ tubes to the 18 inch outer tubes of the Uniflasy set, yet a grill built for one will not accept the other, because the tube end has to meet the valve outlet exactly.
Measure the full length of the old burner, then its width, then the distance between its gas inlets if it has more than one. The 10502 head shows why inlet position matters: its inlets sit 1.25 inches off center, and a head with centered inlets would leave the venturi tubes angled and strained. Write the three numbers down and shop against them, not against the grill’s brand name alone.
Weight tells you something too. A cast iron ring at 6 pounds and a stainless head at about 2 pounds can share a similar footprint while behaving differently once fitted, and the old burner’s weight helps confirm which construction your grill was built around when the part number has long since burned off the metal.
Match the Burner Shape to the Firebox
Shape comes before brand. Grills are built around one burner geometry: straight tubes in rows, a single H or ring casting, or a set of position-specific tubes with a crossover. The replacement has to repeat that geometry, because the firebox mounts, the valve spacing and the heat tents above it were all laid out for the original shape.
Straight tubes, like the J&HYBBQ pack, run front to back or side to side in parallel rows, one per control knob. H burners, like the Char-Broil assembly and the 10502 head, spread one burner across the width of the grill from a central feed. Ring burners, like the 29251, serve older deep fireboxes. Lifting the grates and looking down settles which shape your grill uses in seconds.
Shape also decides how a grill fails. When one straight tube rusts through, only its row loses flame and the rest of the grill still cooks. When a single H or ring burner fails, the whole firebox goes down at once, because there is only one burner to begin with. That is worth knowing when you plan the job: tube grills can often wait for a weekend, while a failed single burner ends cooking on that grill until the part arrives.
Tube Sets, Crossovers and Venturi Tubes
Three parts move gas from the valves to the flame, and they are sold in different combinations. The burner itself makes the flame. The venturi tube carries gas from the valve outlet into the burner. The crossover tube, where fitted, carries flame sideways so one lit burner lights its neighbors from a single igniter.
The Uniflasy set includes its crossover but relies on the grill’s existing venturi arrangement, the Char-Broil kit includes two flexible venturi tubes with its burner, and the 10502 is a head alone that expects listed venturi models to be reused. Before ordering, list which of the three parts your grill needs and check the box contents against that list, so nothing essential is still in transit when the firebox is already apart.
Stainless Steel or Cast Iron
Both materials earn their place, and the burners above split between them: 304 stainless steel for the Uniflasy tubes and the J&HYBBQ pack, stainless for the 10502 head, and cast iron for the 29251 ring. The right choice usually follows the grill, since fireboxes were designed around one construction or the other.
Stainless tubes are light, resist surface rust well and are the standard fitting in current grills, which is why most model-specific sets use them. Cast iron is far heavier, holds heat in the casting and suits the older deep fireboxes it was designed for, but it asks to be kept dry and brushed clean. Match the material to the burner that came out, and the grill keeps the behavior it was built with.
There is also a middle path in this group: the Char-Broil kit states no material at all, which is common for burners sold purely on a part number. When the maker gives no material, buy on the part number and the included hardware instead, and treat the burner as a service part to be inspected each season rather than a lifetime fitting. The stated facts, not the metal, are what make that kit the right one for the grills it lists.
Fitting and Looking After a New Burner
The fitting job itself is short: out with the old burner, in with the new one, then a leak test before the first lighting. The manuals for these parts describe the same sequence, and the maker of the 10502 prints it in full, so the steps below follow that printed routine rather than workshop habit.
The Swap, Step by Step
Start with a cold grill and the gas supply turned off and disconnected, as the 10502 manual directs. Lift out the cooking grates and heat tents, then remove the old burner, noting how it connects to the valve orifices and which hardware holds it, because the new burner goes back in the same orientation.
- Position the new burner and align its gas inlets with the valve orifices
- Refit the mounting hardware so the burner sits steady and does not wobble
- Reconnect the gas supply
- Leak test every connection with soapy water, half soap and half water: bubbles mean a leak
- If bubbles appear, turn the gas off, tighten or replace the faulty part, and test again
- Only then refit the heat tents and grates and light the grill
For the first lighting, the same manual gives the timing to follow: open the lid first, turn the knob to high or light, and press the igniter. If the burner does not light within 5 seconds, turn the gas off and wait 5 minutes before trying again, so unburned gas clears from the firebox instead of building up under a closed lid.
Keeping Ports and Venturi Tubes Clear
Most burner problems after fitting are blockages, not failures. The 10502 manual tells owners to inspect the burner ports for food debris and insect nests and to clear them with a wire brush or a stiff wire, always with the burner cool, and to keep the venturi tubes clear of spider webs and other debris.
A partly blocked port row shows up as a gap in the flame line, and a blocked venturi shows up as a weak or yellow flame, so a quick look along the burner at the start of the season catches both. Check the burner itself at the same time for cracks, heavy corrosion or thin spots. A burner with that kind of damage is a burner to replace, and the measurements from this round make the next order a short one.
Storage matters as well. The same manual advises keeping the burner clean and dry if the grill is stored for an extended period, and covering the grill to protect its components from the elements. Most burners in this group die from moisture and drippings sitting on them through a wet winter, not from the hours they spend lit, so the cover and the end-of-season cleaning do more for burner life than any coating or upgrade.
One measurement and the right shape solve most burner problems: a position-matched tube set for a front-control Spirit, an H kit where venturi tubes have aged with the burner, a cast iron ring for an older firebox, or straight tubes for the big-box brands. Match the stated fitment, run the leak test, and the grill cooks as it did when new.