Key takeaways
- Five mixers for powered speakers compared on maker specs: balanced XLR mains, monitor outputs and output EQ from Yamaha, Mackie, QSC, Behringer, Soundcraft.
The best mixers for powered speakers send a clean line-level signal, because the amplification lives inside the speakers themselves. What separates the desks below is the output section: balanced XLR mains, monitor and control room feeds, output EQ and limiting, all taken from each maker’s published specifications for five current models.
Quick verdict
Powered speakers ask a mixer for three things: balanced line-level outputs that stay quiet over long cable runs, enough output level to drive the speakers’ inputs properly, and separate feeds for monitors or a second zone. All five desks here provide XLR main outputs or a stated main mix output pair.
They divide into analog desks with subgroups and digital desks with output processing. Choose the Yamaha MG16XU for a 16-channel analog desk with locking XLR mains, four group outs and four aux sends. Choose the Mackie ProFX16v3 for the strongest stated main output (+28 dBu on XLR) with subgroups and control room outs. Choose the QSC TouchMix-16 for graphic EQ, limiters and notch filters on the mains and auxes, the Behringer XR18 for a stage-box format with six XLR auxes and a digital speaker bus, and the Soundcraft Signature Plus 16 for Ghost preamps with a dedicated Listen bus and control room section.
| Model | Main outputs | Monitor and aux outputs | Output processing | Channels | Size and weight |
|---|---|---|---|---|---|
| Yamaha MG16XU | XLR balanced stereo out | Monitor out, 4 aux sends, 4 group outs | None stated on outputs | 16 (10 mic) | 444 x 130 x 500 mm, 6.8 kg |
| Mackie ProFX16v3 | XLR and 1/4 inch, +28 dBu | Control room, 2 subgroup pairs, 3 monitor auxes plus FX send | None stated on outputs | 16 (11 mic) | 450 x 434 x 109 mm, 6.9 kg |
| QSC TouchMix-16 | XLR line-level | 6 XLR auxes, 2 stereo TRS auxes, monitor and cue | 1/3-octave GEQ, limiter, notch filters | 22 inputs | 360 x 297 x 89 mm, 5.9 lb |
| Behringer X Air XR18 | 2 XLR, +16 dBu max | 6 XLR auxes, phones | 6-band PEQ or 31-band GEQ per bus | 18 (16 mic) | Stage box; not stated on opened page |
| Soundcraft Signature Plus 16 | Mix L/R | Control room L/R, 4 aux outs, 4 group outs | Listen bus monitoring | 16 (12 mic) | 17.24 x 21.06 x 4.17 in, 17.2 lb |
How we selected these mixers
Selection started from the output section, not the input count. Each mixer below was verified on an opened product page that states its main outputs, its monitor or aux feeds and its channel layout, because a powered-speaker rig fails or succeeds on those connections.
Powered mixers with built-in power amplifiers were excluded: they drive passive speakers, which is the opposite of this keyword. The five split into two analog desks with subgroup routing (Yamaha and Soundcraft), one analog desk with the highest stated output level (Mackie), and two digital systems whose output processing is the story (QSC and Behringer). Where a maker’s page does not state an output level or connector type, the article says so rather than borrowing figures from other models in the same series.
The mixers for powered speakers, compared in detail
Each section follows the same order: who the mixer suits in a powered-speaker rig, the output hardware that feeds the speakers, the processing available on those outputs, and the limits to weigh. Figures such as maximum output level appear only where the maker’s published specification states them for that exact model.
Yamaha MG16XU: locking XLR mains and deep aux routing
The MG16XU is the analog workhorse pick for bands and venues running powered mains with powered wedges. Its main stereo outputs are XLR balanced, and Yamaha notes that the XLR connectors lock to prevent accidental disconnection, a small detail that matters on a stage where cables get stepped on and pulled.
Routing depth is the strength here: four group buses with group outputs, four aux sends including the effects send, a monitor output and a phones output. A typical rig sends the stereo out to the powered mains, one or two auxes to powered wedges, and a group out to a powered subwoofer feed or a second zone. Ten microphone inputs (eight mono plus two mono/stereo) carry D-PRE Class-A preamps with an equivalent input noise of -128 dBu.
Channel tools include 1-knob compressors on channels 1 to 8, PAD switches, 80 Hz high-pass filters, 3-band EQ with a sweepable mid on mono channels, and the SPX processor with 24 programs. USB runs at 24-bit/192 kHz for stereo recording. The desk measures 444 x 130 x 500 mm, weighs 6.8 kg, includes a rack mount kit, and draws 30 W. The limit for speaker work is processing: there is no EQ or limiter on the main outputs themselves, so room correction happens in the speakers or not at all.
- Pros: locking XLR balanced mains; four groups and four auxes for complex powered rigs; D-PRE preamps; rack kit included
- Cons: no output EQ or limiting; stereo USB only; large footprint at 500 mm deep
- Buy if: you mix a full band into powered mains and wedges and want analog subgroups
- Skip if: you need output processing for feedback control or room tuning
Mackie ProFX16v3: the strongest stated main output here
The ProFX16v3 leads on stated output level: its specification puts the XLR main output at +28 dBu, with all other outputs at +22 dBu and output impedance of 120 ohms unbalanced or 240 ohms balanced. Powered speakers with modest input sensitivity, and long cable runs that eat level, are exactly where that headroom at the output pays off.
Main connectors come in both XLR and 1/4-inch formats. Two subgroup pairs (Sub 1-2 and Sub 3-4) have their own master faders and 1/4-inch outputs, control room outputs feed a pair of powered monitors in a studio corner, and three aux sends handle monitor mixes alongside a dedicated FX send. Eleven Onyx preamps provide 60 dB of gain with an EIN of -128 dBu.
Channels carry 3-band EQ with a sweepable mid (100 Hz to 8 kHz), 100 Hz low-cut filters, and single-knob compressors with inserts on channels 1 to 8. The GigFX engine holds 24 effects, and USB runs 2-in/4-out at 24-bit/192 kHz. The steel chassis measures 450 x 434 x 109 mm at 6.9 kg and draws 40 W. Like the Yamaha, it leaves output EQ to the speakers; its case rests on output level, subgroups and channel processing.
- Pros: +28 dBu XLR main output, the highest stated here; subgroups with own faders; control room outs; 60 dB preamp gain
- Cons: no output EQ or limiter; monitor auxes are 1/4-inch rather than XLR
- Buy if: your powered speakers need a hot, clean feed and you mix monitors from the desk
- Skip if: you want per-output graphic EQ or a digital stage-box format
QSC TouchMix-16: output EQ, limiters and notch filters built in
The TouchMix-16 is the pick when the room fights back. Its main outputs and auxes 1 to 6 carry 1/3-octave graphic EQ, a limiter, four variable notch filters and variable high- and low-pass filters, which is the processing set used to tame feedback and protect powered speakers from sustained overload at the mix position.
Outputs are all line-level: two main XLRs, six XLR auxes, two stereo TRS auxes that can drive wired in-ear monitors directly, plus stereo monitor and cue feeds, giving ten aux output channels for monitor mixing. Inputs total 22, including 12 XLR microphone inputs, four combo mic/line inputs and a talkback input, with 48V phantom power switchable per channel.
Every input channel has 4-band parametric EQ, gate and compressor. Four effects engines hold 50 factory and 50 user presets, eight DCA groups organize control, and the desk records 20 tracks to a USB hard drive. The color touchscreen and included Wi-Fi adapter with a remote app suit engineers who mix from the audience. It measures 360 x 297 x 89 mm and weighs 5.9 lb, the lightest full rig here. The trade-off is the touchscreen workflow itself and a 44.1/48 kHz sampling ceiling.
- Pros: graphic EQ, limiter and notch filters on mains and auxes; ten aux output channels; per-channel phantom; multitrack recording
- Cons: touchscreen-first control; sampling limited to 48 kHz; maximum output level not stated on the opened page
- Buy if: feedback control and monitor mixes matter more than physical faders
- Skip if: you want a traditional analog surface or higher sample rates
Behringer X Air XR18: a stage box that feeds speakers digitally too
The XR18 removes the desk entirely: an 18-input stage box with 16 Midas-designed programmable preamps, controlled from tablets or computers over its built-in tri-mode Wi-Fi router or Ethernet. For powered speakers, its analog feed is two XLR main outputs and six XLR aux outputs, with a stated maximum output level of +16 dBu.
Each of the six aux buses and the main LR bus carries inserts, full dynamics and a choice of 6-band parametric or 31-band graphic EQ, so powered wedges get their own tuned feed. The ULTRANET port adds a digital path: it sends 16 channels over a Cat 5 cable to P16 personal monitor mixers, and the maker’s copy notes that Turbosound iQ Series powered loudspeakers can tap that digital bus directly, skipping a conversion stage.
Recording runs over an 18×18 USB interface at 24-bit/48 kHz with 114 dB converter dynamic range and 0.8 ms analog latency. The X32 effects rack offers four stereo slots, a 100-band real-time analyzer overlays every channel and bus EQ, and Dugan-style auto-mixing manages panel microphones. There are no faders or screen on the box, so a dead tablet battery ends control; engineers who want physical backup should weigh that honestly.
- Pros: six XLR auxes with per-bus EQ; ULTRANET digital feed to compatible powered speakers; 18×18 USB; auto-mixing
- Cons: no physical controls on the unit; output level lower than the Mackie; control depends on the app and network
- Buy if: you mix from a tablet and want the mixer on stage next to the powered speakers
- Skip if: you need hands-on faders or a self-contained control surface
Soundcraft Signature Plus 16: Ghost preamps and a proper Listen bus
The Signature Plus 16 is the newest design here, an analog desk built around Soundcraft’s Ghost preamps and a monitoring section aimed at engineers who check mixes constantly. Its outputs are a Mix L/R pair, a Control Room Mix L/R pair, four aux outs and four group outs, plus a headphone jack.
The Pro Listen bus is the distinctive feature: it previews tracks or submixes without interrupting the main mix to the audience, and the headphone and control room outputs carry Mute, Dim and Mono Sum controls with aux monitoring. For powered-speaker work that means checking a wedge feed or a recording submix on headphones or control room speakers while the mains keep playing.
Twelve microphone inputs carry Ghost preamps, Sapphyre EQ (12 kHz high, sweepable 150 Hz to 3 kHz mid, 60 Hz low), switchable pads and 100 Hz high-pass filters, with dbx one-knob compressors on the ten mono channels and Hi-Z switches on channels 7 to 10. A Lexicon effects processor with Store and Tap Tempo, a talkback input with routing, and a 4×4 USB-C interface at 192 kHz complete the panel. It measures 17.24 x 21.06 x 4.17 inches and weighs 17.2 lb. As a newly released model it is listed on pre-order at the time of writing, and its main output connector type and level are not stated on the opened page.
- Pros: Ghost preamps with Sapphyre EQ; Listen bus and full control room section; 4×4 USB-C at 192 kHz; talkback routing
- Cons: newly released and on pre-order; main output level not stated on the opened page; heaviest here at 17.2 lb
- Buy if: you monitor constantly while mixing and want an analog desk with modern USB
- Skip if: you need a mixer that ships today or stated output-level figures
Buying guide: what powered speakers need from a mixer
A powered speaker already contains its amplifier and usually its own input gain control, so the mixer’s job changes: no speaker outputs, no power ratings, just clean line-level signal at the right level with the right routing. The five sections below translate that into checks you can run against any product page before buying.
Balanced outputs and why XLR mains matter
Balanced connections reject the hum and interference that long cable runs collect, and powered speakers are often placed far from the mixer, on stands at the room’s edges. XLR main outputs, fitted to the MG16XU, ProFX16v3, TouchMix-16 and XR18, are the standard answer, and the MG16XU’s locking XLRs add mechanical security.
Balanced TRS works on the same principle where XLR is not offered.
Unbalanced RCA or consumer-level outputs are the weak point in a powered rig: they are more prone to noise over distance and usually run at a lower nominal level. If a desk you like offers only unbalanced mains, keep cable runs short and expect to manage gain staging carefully. The connector list on the product page tells you which situation you are in before any money moves.
Output level: reading the +dBu figure
Maximum output level tells you how hard a mixer can drive a speaker’s input. The ProFX16v3 states +28 dBu on its XLR mains and the XR18 states +16 dBu maximum, and both will drive typical powered speakers, whose inputs are built for professional line level.
The practical difference shows up with quiet program material, long cable runs and speakers whose input sensitivity is conservative.
Where a maker does not state the figure, as with the TouchMix-16 and Signature Plus 16 pages opened for this guide, treat it as an unknown rather than a flaw, and check the model’s full specification document if your speakers are known to need a hot feed. Nominal level (+4 dBu professional versus -10 dBV consumer) matters as much as the maximum when matching a mixer to a speaker’s input switch.
Monitor feeds: auxes, subgroups and control room outs
Powered wedges and in-ear systems each need their own mix, and the feed count decides how many distinct monitor mixes a desk can build. The TouchMix-16 offers ten aux output channels, the XR18 six XLR auxes with per-bus EQ, and the MG16XU four aux sends plus four group outs that can feed a second zone or a subwoofer group.
Subgroups and control room outputs serve different jobs: subgroups (ProFX16v3, MG16XU, Signature Plus 16) feed a powered sub or a delay fill with a related mix, while control room outs mirror the mains for studio monitors. Count the powered boxes in your rig, mains, wedges, subs and fills, and require one suitable output per box or per stereo pair before choosing.
Output EQ and limiting: the digital desks’ advantage
Analog desks here put their EQ on the input channels and leave the outputs bare, so feedback control relies on speaker placement and the speakers’ own DSP. The digital desks move processing onto the outputs: the TouchMix-16 runs graphic EQ, limiters and notch filters on mains and auxes, and the XR18 offers parametric or graphic EQ on every bus.
A limiter on the main output is also speaker protection, capping the level a powered speaker can be asked to reproduce during a feedback spike or a dropped microphone. If your powered speakers include their own DSP limiters, the mixer’s output processing is a convenience; if they do not, it becomes part of the protection chain and deserves real weight in the decision.
Choosing mixers for powered speakers by rig size
Match the desk to the rig, not to the band’s ambitions. A duo with two powered mains and one wedge needs balanced mains and a single aux, which every desk here exceeds. A full band with four wedge mixes and a sub feed needs the aux and group counts of the MG16XU or the TouchMix-16’s ten aux channels.
Tablet mixing suits the XR18 when the stage box can sit beside the speakers.
Also weigh what travels: the TouchMix-16 at 5.9 lb and the XR18 stage box pack small, while the MG16XU and Signature Plus 16 are full-size desks that want a case and a table. Powered speakers removed the amplifier rack from the truck; the mixer choice decides how much of that saved space comes back.
Frequently asked questions
These answers cover the connection questions that come up when a mixer meets powered speakers, using the specifications verified above. Speaker-side figures such as input sensitivity belong to the speaker’s own manual, and the answers flag where that document decides the detail.
Can I use a powered mixer with powered speakers?
A powered mixer’s amplifier outputs are designed for passive speakers and should not feed powered speakers, whose inputs expect line level. Most powered mixers also provide line-level main outputs, and those are the correct connection. Use them instead.
The desks in this guide are unpowered mixers with line-level outputs throughout, which is the straightforward match for powered speakers and removes the question entirely.
Do mixers for powered speakers need speaker outputs?
No. Speaker outputs, binding posts or Speakon connectors carrying amplifier power belong to powered mixers and amplifiers. A mixer for powered speakers needs line-level outputs, ideally balanced XLR, plus monitor feeds. Nothing on the desk should be able to power a passive speaker.
Every desk here follows that pattern: XLR or stated mix outputs for the mains, aux or subgroup feeds for wedges and fills, and headphone or control room outputs for checking the mix at low volume.
How do I connect a subwoofer in a powered rig?
Three routes are common. Many powered subwoofers accept the full-range feed and pass a filtered signal on to the mains, which needs only the mixer’s main outputs. A group or aux output can feed the sub separately, as the MG16XU’s group outs and the ProFX16v3’s subgroup outs allow, giving the sub its own level control.
Digital desks can also low-pass an aux feed, using the TouchMix-16’s variable filters or the XR18’s bus EQ.
What cable length can balanced outputs handle?
Balanced line-level runs of 30 meters or more are routine in live sound, which is one reason the XLR mains on these desks suit powered speakers placed across a room or stage. Keep runs balanced end to end, and route them away from mains power cables where possible.
Let the mixer’s output level and the speaker’s input gain share the work rather than running either at its extreme.
Should the mixer or the speaker handle room EQ?
Either can, and many rigs split the job: broad room correction on the mixer’s output EQ where it exists, and per-speaker adjustments in the speakers’ own DSP. On the analog desks here there is no output EQ, so the speakers’ controls or an external processor do the work.
On the TouchMix-16 and XR18, the output processing is built in, which keeps the correction at the mix position where you can hear the result.
Conclusion
For powered speakers, the output section is the product: the MG16XU brings locking XLR mains and group routing, the ProFX16v3 the strongest stated output level, the TouchMix-16 built-in output EQ and limiting, the XR18 a stage box with a digital speaker bus, and the Signature Plus 16 a Listen bus for checking feeds mid-show.