Updated Nov 16, 2026· 13 min read

Key takeaways

  • Compare kitchen faucets for 4 hole decks where every model's page states a 4-hole installation with a side sprayer, filling all four holes in the sink deck.

Most modern faucets cover one or three holes and leave a fourth hole to plug. This guide compares kitchen faucets for 4 hole decks only where the listing page itself states a 4-hole installation, which in this group means two handle or single handle faucets sold with a side sprayer that takes the fourth hole.

Quick verdict

All six models below print a 4-hole 8 in installation on their pages and include a side sprayer. The Delta Foundations B2410LF and Delta Classic 2402LF are the two handle picks, the Delta Classic 400-DST is the single handle pick with a sealed valve, and the Moen Chateau is the low profile option.

A true four hole faucet is a specific layout: hot and cold handles or a single body, the spout, and a side sprayer, spread across an 8 in pattern. That layout is exactly what each page here describes, including the sprayer in the box rather than as an accessory. The group splits by handle count, three two-handle models and three single handle models, and by deck thickness limits that run from 7/8 in to 2-1/2 in as printed, which turns out to be the sharpest difference between them.

Product Type Best for Key spec Main limit
Delta Foundations B2410LF Two handle, side sprayer Standard 4 hole decks 4-hole 8 in install, 9-1/4 in reach Supply lines not included
Delta Classic 2402LF Two knob handle, side sprayer Classic styling 4-hole 8 in install, solid brass Handles listed as required accessory
Delta Foundations B4410LF Single handle, side sprayer One handle control 4 holes, 8 in centers, 9-1/2 in reach Ball valve type
Delta Classic 400-DST Single handle, side sprayer Thicker decks 2.5 in max deck, DIAMOND Seal valve Standard spout, 180 degree swing
Delta Windemere 21996LF-SS Two handle, side sprayer Stainless finish 4-hole 8 in install, 1.8 gpm 1.31 in max deck thickness
Moen Chateau 7430 Single handle, side sprayer Low profile decks 4 hole, 9-1/8 in reach, 1.5 gpm 7/8 in max deck thickness

How we selected

The four hole brief had the strictest filter of any guide here: a model counted only if its opened page states a 4-hole installation, or a deck plate, side spray and dispenser layout that fills four holes in the page own wording. Models that merely fit three holes with a plate were excluded, however good they are elsewhere.

Every model below passed that test on its own listing page, with the sprayer listed as included. Pages were read one at a time and each showed its model in stock or available to ship. The trade of the layout is stated up front in each section: these are standard spout faucets with a separate sprayer, not pull down designs, and their spout heights and reaches are printed accordingly.

The filter also cut models that almost qualify, and it is worth saying why. A single post faucet with a long deck plate and a separate counter sprayer can fill four holes as a combination, but the page for the faucet alone does not state a 4-hole installation, and the combination is two purchases with two spec tables. This guide keeps the stricter reading so that every model named can be checked against one page.

Kitchen faucets for 4 hole decks in detail

Three models use two handles and three use one, and all six include the side sprayer that fills the fourth hole. Read the deck thickness line in each section carefully, because the spread from 7/8 in to 2-1/2 in is wider than in any other guide in this series.

Delta Foundations B2410LF

The B2410LF page states the brief in its first lines: a 4-hole 8 in installation with a side sprayer included. Printed specs include a brass body, a washerless valve, two lever handles, a faucet height of 6-7/16 in, a spout reach of 9-1/4 in, a flow rate of 1.8 gpm and a 360 degree spout swivel.

The page lists a maximum deck thickness of 1-1/8 in, a 1/2 in connection size, a deck plate as included and a chrome finish on the listing read. Two handles on an 8 in spread plus the sprayer fill all four holes of a standard four hole deck with no plugs and no extra parts beyond the install itself.

The parts note is that supply lines are listed as not included, so they join the shopping list. The low standard spout, at 6-7/16 in overall height, also means tall pots are filled with the side sprayer rather than under the spout.

The two lever handles deserve a word for older decks: separate hot and cold levers on an 8 in spread are the control layout most four hole sinks were built around, so hand habits and handle clearance carry over from the faucet being replaced. Nothing about the install asks the household to relearn the sink.

  • Pros: true 4-hole 8 in layout with sprayer included
  • Pros: brass body; 9-1/4 in reach
  • Cons: supply lines not included
  • Cons: low standard spout height
  • Buy if: your four hole deck is a standard sink ledge
  • Skip if: you want a high arc spout over the bowl

Delta Classic 2402LF

The 2402LF is the classic two knob version of the same layout: its page states a 4-hole 8 in installation and includes a side sprayer, with a solid brass body and a washerless valve. Printed dimensions are a faucet height of 6-11/32 in and a spout reach of 9 in, with a flow rate of 1.8 gpm and a 360 degree swivel.

The page describes a white vegetable sprayer that mounts on the left or right side of the sink, a small flexibility that matters on decks drilled with the sprayer hole on a fixed side. Maximum deck thickness is printed as 7/8 in, the thinnest limit in this group, and the finish read was chrome with acrylic knob handles.

One parts warning is printed in the description: handles are listed as a required accessory, with handle models DH215, DH212 or DH25 named, even though the components list marks handles as included. Confirm which handles ship with the exact listing before ordering.

  • Pros: solid brass body; sprayer mounts left or right
  • Pros: classic knob handle styling
  • Cons: handles listed as a required accessory on the page
  • Cons: 7/8 in max deck thickness
  • Buy if: you want the traditional four hole look
  • Skip if: your deck is thicker than 7/8 in

Delta Foundations B4410LF

The B4410LF is the single handle Foundations model, verified on two opened pages that agree on the layout: a 4-hole 8 in installation with a side sprayer included, 4 holes on 8 in centers and a deck mounted, widespread configuration. Printed specs include a spout reach of 9-1/2 in, the longest in this group, and a flow rate of 1.8 gpm.

The valve type is listed as Ball, the handle is a single lever, the maximum deck thickness is printed as 1.38 in, the connection size is 1/2 in and the spout swivels 360 degrees. One handle controlling both temperature and flow is the practical difference from the two handle models: one hand runs the water while the other holds the pot.

The ball valve is the older technology in this group, where the 400-DST below lists a sealed diamond valve design. Buyers who rank valve type first should weigh that page difference directly.

  • Pros: single handle control with a true 4 hole layout
  • Pros: longest reach here at 9-1/2 in
  • Cons: ball valve type
  • Cons: 1.38 in max deck thickness
  • Buy if: you want one lever and a side sprayer
  • Skip if: you prefer a ceramic disc or sealed valve

Delta Classic 400-DST

The 400-DST pairs the four hole layout with the thickest deck rating in this group: its page states a 4-hole 8 in installation, an included side sprayer and a maximum deck thickness of 2.5 in. For a four hole deck on a thicker counter or a heavy sink ledge, that printed maximum is the deciding line.

The page lists a single lever handle, a DIAMOND Seal valve described as a valve embedded with diamonds, a ceramic disc valve type in its table, a flow rate of 1.80 gpm at 60 psi, a spout length of 8 in, a spout height from deck to aerator of 5 in and a standard spout that swings 180 degrees. The sprayer hose is specified at 45 in, a deck plate or escutcheon is listed among the included parts, the connection is 3/8 in compression and the finish read was chrome.

The spout is a standard low design with a half-circle swing, so the sprayer does the reaching. Within this layout that is normal, and the 45 in sprayer hose figure is printed to judge it by.

It is also the only model in this group whose page prints both a sealed valve description and a ceramic disc valve type, two wordings the maker uses for the same cartridge system.

  • Pros: 2.5 in max deck, thickest rating here
  • Pros: sealed valve design as the maker describes it
  • Cons: standard spout swings 180 degrees only
  • Cons: low 5 in spout height to the aerator
  • Buy if: your four hole deck is thick
  • Skip if: you want a high arc spout

Delta Windemere 21996LF-SS

The Windemere is the stainless finish entry: its page states a 4-hole 8 in installation with a side sprayer included, two lever handles and a cartridge valve. Assembled dimensions are printed as 11-5/8 in high by 9-3/4 in deep by 15-1/2 in wide, the tallest and widest body in this group, and the finish is listed as stainless steel.

The page lists a flow rate of 1.8 gpm, a maximum deck thickness of 1.31 in, a 1/2 in connection, a deck mount widespread configuration and a standard spout that swivels 360 degrees. The taller assembled height gives this two handle model more presence over the sink than the low Foundations and Classic bodies.

The 1.31 in deck limit sits mid-group: fine on sink ledges and standard counters, short of the 400-DST figure on thick stacks. The sprayer hose length line on the page is printed without its number, so that figure is not quoted here.

  • Pros: stainless finish; taller two handle body
  • Pros: cartridge valve; 360 degree swivel
  • Cons: 1.31 in max deck thickness
  • Cons: sprayer hose length not printed in full
  • Buy if: you want a stainless four hole faucet with two levers
  • Skip if: your deck stack is thick

Moen Chateau 7430

The Chateau is the Moen entry and the low profile of the group: its page lists 4 Hole in its characteristics with a side spray marked Yes, a faucet height of 8-1/2 in, a spout height of 5-7/16 in and a spout reach of 9-1/8 in. The finish read was polished chrome on a metal body with a cartridge valve and a single lever handle.

Flow rate is printed as 1.5 gpm, the spout swivels 180 degrees, and the page describes a side spray hose for flexible cleaning at the sink, an aerated stream and the Duralock quick connect system. It also states the standard design mounts on the sink or countertop, and supply lines are listed as included, the only model here whose page says that.

The limit is the thinnest mounting figure alongside the Classic knob model: a maximum deck thickness of 7/8 in, and the deck plate is listed as not included, which matters less on a true four hole deck where every hole is already assigned.

For a like-for-like replacement on an existing four hole deck, that included-lines detail is the difference between a one-trip install and a second trip for parts the old faucet simply reused.

  • Pros: supply lines listed as included
  • Pros: low profile single handle design
  • Cons: 7/8 in max deck thickness
  • Cons: 1.5 gpm flow; 180 degree swivel
  • Buy if: your four hole deck is a thin sink ledge
  • Skip if: your deck is a thick counter stack

Buying guide for kitchen faucets for 4 hole decks

A four hole deck is a fixed layout, so buying is mostly verification: the faucet must state the layout, fill every hole and clamp your deck. These checks run in that order and use the printed figures from the product sections and nothing beyond them.

Confirm the page states a 4-hole installation

This is the filter the whole guide rests on. Every model here prints a 4-hole 8 in installation line or a 4 Hole characteristic on its page. A 1 or 3 hole faucet with a long deck plate is a different product: it covers three holes at most and leaves the fourth to a plug or a dispenser.

Read the installation line and the number of holes field on the listing page, not the photo, because photos often show a variant with a different layout.

Check what fills the fourth hole

On every model here the fourth hole takes the included side sprayer. That is the layout to verify in the components list, where each page names the side sprayer among the included parts. If a listing instead fills the fourth hole with a dispenser, the sprayer function is not part of that box.

The 2402LF page adds a useful detail: its sprayer mounts on the left or right, which suits decks whose fourth hole sits on either side.

Measure deck thickness against a wide spread

The printed maximum deck thickness figures here run from 7/8 in on the 2402LF and Chateau to 2.5 in on the 400-DST, with 1-1/8 in, 1.31 in and 1.38 in between. Four hole decks are often stainless sink ledges, which are thin, but a counter mounted four hole layout can be far thicker.

Measure at the hole and match the model to the measurement; this single figure rules out more models in this group than any other.

Choose one handle or two, from the page

Three models here use two handles, the B2410LF, 2402LF and Windemere, and three use a single lever, the B4410LF, 400-DST and Chateau. Two handles give separate hot and cold control at the deck; a single lever mixes with one hand, which helps when the other hand holds a pot under the sprayer.

Valve types printed differ with the layout: washerless on the two Foundations and Classic two handle models, ball on the B4410LF, cartridge on the Windemere and Chateau, and a sealed diamond valve design on the 400-DST.

Set expectations for the spout and sprayer

These are standard spout faucets: stated spout heights run from 5 in to the aerator on the 400-DST to 5-7/16 in on the Chateau, and reaches run from 9 in to 9-1/2 in. Tall pots are filled with the side sprayer, whose hose the 400-DST page specifies at 45 in.

If you expect pull down wand convenience, this layout is not it; if you want every drilled hole filled by the faucet itself, it is the only layout that does so as printed.

FAQ

These answers use the installation, components and dimension lines printed on the listing pages behind this guide. The group is limited to models whose pages state the four hole layout, and the answers keep that same discipline from start to finish. No exceptions are made.

What is a 4 hole kitchen faucet layout?

As the pages here print it, a 4-hole 8 in installation: the spout and handles spread across an 8 in pattern and the fourth hole takes a side sprayer. The B2410LF page words it as a 4-hole 8 in installation with an included side sprayer, and the B4410LF pages add 8 in centers and a widespread configuration.

It is the classic deck layout from before single post faucets became standard, and current models are still sold in it, as these six listings show.

Can a 1 or 3 hole faucet cover a four hole deck?

Not fully, on the printed figures. A deck plate covers up to three holes under a single post faucet; the fourth hole still needs a plug, a dispenser or a sprayer from another source. That is why this guide only includes models whose pages state the 4-hole installation with the sprayer included.

If you prefer a pull down model, the honest route is a three hole faucet plus a separate plan for the fourth hole, not a claim that the plate covers it.

Are supply lines included with these faucets?

The pages differ, which is why the components list matters: the Chateau page lists supply lines as included, while the B2410LF and 2402LF pages list them as not included. The other pages read did not put supply lines in the figures quoted here on this point.

Check the included components on the exact listing before ordering so the install does not stall on a missing pair of lines on install day.

How thick a deck can a four hole faucet clamp?

As printed in this group: 2.5 in for the Delta Classic 400-DST, 1.38 in for the B4410LF, 1.31 in for the Windemere, 1-1/8 in for the B2410LF and 7/8 in for the 2402LF and the Moen Chateau. That spread is the widest of any group in this series, by a wide margin.

Thin stainless ledges suit any of them; thick counter stacks narrow the choice to the 400-DST figure.

Does the side sprayer replace a pull down wand?

It does the same jobs from a separate mount: rinsing the bowl corners, filling pots beside the spout and washing produce. The 400-DST page specifies a 45 in sprayer hose, and the 2402LF page notes its sprayer mounts on the left or right of the sink, as needed.

The difference is that the sprayer is a separate fixture in its own hole, which is exactly what a four hole deck is drilled for in the first place.

Conclusion

For a true four hole deck, the B2410LF and 2402LF cover two handle installs, the B4410LF and 400-DST give single handle control, and the Windemere and Chateau add stainless and low profile options. Check the stated deck thickness against your own deck first, then pick the handle layout. The printed limits in this group run from 7/8 in to 2.5 in.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.