Key takeaways
- Five meat grinders for raw dog food compared on maker-stated bone capacity, stated throughput and plate sets, from a compact boneless #8 unit to a 1.5 HP #32.
Raw meals ground at home stand or fall on the hardware doing the work: bone-in batches need a bone capacity the maker states outright, while boneless mixes need steady, repeatable output. These meat grinders for raw dog food were chosen on maker-stated bone lists, plate sets and throughput figures alone.
Quick verdict
Four of these five grinders carry a maker-stated bone capacity for raw batches, and the fifth is a boneless specialist whose maker names pet food preparation directly. The LEM BigBite #32 leads on stated output, the STX Turboforce II 4000 leads on plate variety, and the VEVOR #12 leads on stated plate sizes in a mid-size build.
- For the largest bone-in batches: LEM Products BigBite #32 Meat Grinder, at approximately 17 pounds per minute with chicken bones stated.
- For plate variety and a reverse gear: STX International Turboforce II 4000 (Platinum Edition), with six plates and soft bones stated.
- For a mid-size bone-in grinder: LEM Products BigBite #12 Meat Grinder, at up to 11 pounds per minute with raw chicken bones stated.
- For stated plate sizes and dishwasher-listed parts: VEVOR Commercial Meat Grinder, #12, 550W/0.7HP, with plates at 4.5mm and 10mm.
- For boneless raw batches only: LEM Products BigBite #8 Meat Grinder, pet food use stated, bones ruled out.
Every bone claim stops where the maker stops it: no model here states a bone larger than chicken.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| LEM Products BigBite #32 Meat Grinder | #32 electric grinder | Largest raw batches | Approximately 17 lbs per minute; plates at 4.5mm and 10mm | Heaviest pick at 64.8 pounds |
| STX International Turboforce II 4000 (Platinum Edition) | #12 electric grinder | Bone-in batches with plate variety | Grinds 175 to 225 lbs per hour on high speed | Soft bones only: chicken, rabbit, squirrel, quail |
| LEM Products BigBite #12 Meat Grinder | #12 electric grinder | Mid-size bone-in batches | Up to 11 lbs per minute; raw chicken bones stated | Maker does not state plate sizes in numbers |
| VEVOR Commercial Meat Grinder, #12, 550W/0.7HP | #12 electric grinder | Stated plate sizes and tubes | Plates at 4.5mm and 10mm; up to 11 lbs per minute | Bone wording covers chicken bones and cartilage |
| LEM Products BigBite #8 Meat Grinder | #8 electric grinder | Boneless raw batches | About 7 lbs per minute; pet food preparation stated | Maker states the model is not for bones |
How we selected
Each model here earned its place from statements on its own maker or listing page: a stated bone capacity, a stated pet food use, a stated throughput, or a stated plate set. If a page named no bone and no pet food use, the grinder did not make this list, however strong its motor sounded on paper.
Bone wording came first, because it is the hardest limit in raw batch work. A grinder whose maker names raw chicken bones can be matched to chicken-frame batches, and a grinder whose maker names no bones at all was left out, even when its wattage figure ran high. The one boneless model included, the BigBite #8, is here because its maker states pet food preparation in plain words.
Throughput and plate sets came next. Makers state output in different units, pounds per hour from STX and pounds per minute from LEM and VEVOR, so each figure below keeps the maker’s own unit. Plate sets matter because raw batches move between coarse and fine textures, and a maker who states plate sizes in millimeters gives the buyer more to plan around than one who lists plates by name.
The comparison stays on hardware: what each maker states the machine can grind, how fast it states the machine works, which plates and tubes sit in the box, and where the stated limits fall. Nothing here rates one mix against another or promises anything for the animal eating it.
The meat grinders for raw dog food, model by model
The five models below run from a 0.5 HP #8 built for boneless batches to a 1.5 HP #32 whose maker rates it for raw chicken bones at approximately 17 pounds per minute. Each entry sticks to what the maker states: bone lists, output figures, plate sets, included parts, and the limits printed beside them.
LEM Products BigBite #32 Meat Grinder
LEM gives this #32 the strongest bone wording on the list: the maker states the grinder can also process chicken bones, and describes it as a way to create a raw diet for your pet without unnecessary fillers. Stated output runs to approximately 17 pounds of meat per minute, the highest per-minute figure among the five picks here.
This is the pick for households grinding large raw batches, where a whole session of chicken frames and boneless meat moves through one machine. The 1.5 HP motor is permanently lubricated, carries a built-in circuit breaker, and drives a stainless steel knife, head and auger.
The plate set is stated in numbers: 4.5mm and 10mm stainless steel plates plus a stuffing plate, with three plastic stuffing tubes at 1/2 inch, 1 inch and 1 1/8 inch outside diameter. A storage drawer sits in the body, the design is noise-dampened, and LEM states a five-year factory warranty with lifetime customer support. The trade-off is mass: at 64.8 pounds it wants a permanent counter spot or a cart, and its stated bone ceiling is chicken, nothing larger.
- Pro: Maker states chicken bone processing beside the highest per-minute output here, approximately 17 lbs per minute
- Pro: Plate sizes stated in numbers at 4.5mm and 10mm, plus a stuffing plate and three tubes
- Pro: Stainless steel knife, head and auger with a built-in circuit breaker
- Con: At 64.8 pounds it is the heaviest model on this list by a wide margin
- Con: The stated bone list stops at chicken bones, with no larger bone named
Buy if your raw batches are large, regular, and built around chicken bones, and you want the maker’s pet food wording behind the pick. Skip if counter space is tight, it must move after every session, or your batches call for bones beyond the chicken size the maker names.
STX International Turboforce II 4000 (Platinum Edition)
STX states this #12 grinder is capable of grinding soft bones such as chicken, rabbit, squirrel and quail, and the maker also names use in the B.A.R.F. (Bones and Raw Food) diet for pets. It pairs that bone wording with the widest plate set on this list: six plates in total, five of them grinding plates in tempered steel.
The fit is for raw feeders who vary texture and who grind smaller soft bones beside chicken. A three-speed system (High, Low and Reverse) gives a low gear for dense loads and a reverse for clearing the head, and a foot pedal lets the operator run the motor while both hands stay on the tray and the stomper. Output is stated at 175 to 225 pounds of meat per hour on high speed, with 2000 watts of peak output power and 600 watts of running power at no load.
The grinding head is 100 percent polished cast aluminum in four parts, not coated, and the maker calls for hand washing. Three stainless steel cutting blades in 304 grade steel, three sausage tubes at 3/4, 5/8 and 1/2 inch, a kubbe attachment, two meat claws and a burger-slider press round out the box. The tray holds more than 3 pounds, the set-up unit measures 19 by 8 by 14 inches and weighs 13 pounds set up, and a patented Quad Air Cooling system with four air intakes cools the motor. The bone list names soft bones only, and the maker does not state the five plate sizes in numbers.
- Pro: Maker states soft-bone grinding and names chicken, rabbit, squirrel and quail
- Pro: Six plates and three cutting blades give the widest texture range on this list
- Pro: Three speeds with reverse, plus a foot pedal for hands-busy feeding
- Con: The maker does not state plate sizes in numbers, so textures are chosen by eye
- Con: The cast aluminum head is hand wash only, per the maker
- Con: Bone wording covers soft bones only, with nothing larger stated
Buy if your batches lean on chicken frames and smaller soft bones and you want plate variety, reverse and pedal control in a #12 body. Skip if you want every part in stainless steel, or batches centered on bones larger than the maker’s stated list.
LEM Products BigBite #12 Meat Grinder
The #12 BigBite carries the same maker bone wording as its larger stablemate, scaled to a mid-size body: LEM states it handles raw chicken bones and processes up to 11 pounds of meat per minute. The maker also describes making pet food out of scraps and creating a raw diet for your pet without unnecessary fillers, in its own words.
For households whose raw batches sit between the compact #8 and the full #32, this is the balanced pick: a 0.75 HP motor, a stainless steel knife, head and auger, and a meat pan the listing rates at 7 lb capacity. The motor is permanently lubricated, the design is noise-dampened, and a storage drawer holds the plates and tubes between sessions.
In the box, LEM lists a coarse plate and a fine plate plus a stuffing plate, three stuffing tubes and a plastic meat stomper. One gap stands out: plate size. The maker does not state the coarse and fine sizes in millimeters on the listing, so a buyer who plans textures by number will find less to work with here than on the #32 or the VEVOR. The unit weighs 33.1 pounds, and its stated bone ceiling matches the bigger model: raw chicken bones, named plainly, and nothing beyond them.
- Pro: Maker states raw chicken bone handling at up to 11 lbs per minute
- Pro: Stainless steel knife, head and auger in a 33.1 pound body
- Pro: Storage drawer, noise-dampened design and a permanently lubricated motor
- Con: Plate sizes are not stated in numbers on the maker’s listing
- Con: Output sits well below the #32 for very large batch days
Buy if your raw batches are mid-size and chicken-based, and you want LEM’s stated bone and pet food wording without the #32’s weight. Skip if you plan every grind by millimeter plate sizes, or if your batch days run long enough to want the larger model’s output.
VEVOR Commercial Meat Grinder, #12, 550W/0.7HP
VEVOR states this #12 grinder easily grinds chicken cartilage, chicken bones, frozen and fresh meat, and the maker lists pet food preparation among its stated uses. It is also the only mid-size model here whose page states exact plate sizes: a 10mm coarse plate and a 4.5mm fine plate, plus a stuffing plate in the box.
The build suits raw feeders who grind often. The 550W, 0.7 HP motor drives a three-stage auger and a cross-sharp steel blade at a stated up to 11 pounds of meat per minute, two cross blades are included, and the housing is stainless steel. Three sausage stuffing tubes come sized at 0.47 inch (12mm), 0.87 inch (22mm) and 1.2 inch (30mm), and the unit carries ETL approval, rapid cold-air cooling and a reset button for overload protection.
Cleanup gets unusual attention from this maker: the blades, plates, tubes, head, auger and pan are listed by the maker for dishwasher cleaning, a claim no other maker here makes for its full parts set. Anti-vibration foot pads round out the spec sheet. The limits sit in the bone wording, which covers chicken bones and cartilage and names no other bone, and in the commercial framing: this is a work-first machine, aimed at steady output rather than counter display.
- Pro: Maker states chicken bone and cartilage grinding plus pet food preparation
- Pro: Plate sizes stated exactly at 10mm and 4.5mm, with three sized stuffing tubes
- Pro: Maker lists the full parts set for dishwasher cleaning
- Con: Bone wording names chicken only, with no smaller soft bones listed beside it
- Con: Commercial styling suits a work counter more than a display kitchen
Buy if you want stated plate sizes, a stated chicken-bone capacity and dishwasher-listed parts in a #12 commercial build. Skip if your batches rely on the smaller soft bones only STX names, or if you prefer a unit with a storage drawer.
LEM Products BigBite #8 Meat Grinder
The smallest BigBite is the honest boneless pick: LEM states it processes about 7 pounds of meat per minute for burgers, sausage, pet food and bulk meal prep, and states in the same breath that it is not for bones. For raw batches built on boneless meat and organs, that stated pet food use is the whole fit, stated by the maker itself.
Households grinding boneless raw mixes in moderate batches get a compact stainless steel grinder with a 0.5 HP motor, three plates, a knife, a stomper and stuffing tubes. The motor is permanently lubricated, the design is noise-dampened for quieter running, and the parts disassemble for cleaning. At 32.6 pounds it is the lightest model here, and the listing rates its capacity at 7 lb, which suits a weekly batch rhythm.
The limits define this pick. No bone belongs in it, by the maker’s statement, so a household that later moves to bone-in batches will outgrow it. Plate sizes are not stated in numbers on the listing, and the stated output, about 7 pounds per minute, is the lowest on this list. Within those lines, it is the only model here whose maker aims the copy at pet food preparation in a compact body.
- Pro: Maker states pet food preparation in plain words
- Pro: Lightest pick here at 32.6 pounds, with a compact #8 body
- Pro: Permanently lubricated motor and a noise-dampened design
- Con: Maker states the model is not for bones, in any batch, at any size
- Con: Lowest stated output here, at about 7 lbs per minute
- Con: Plate sizes are not stated in numbers on the maker’s listing
Buy if your raw batches are boneless and moderate in size, and you want the maker’s stated pet food wording in a compact grinder. Skip if any part of your batch plan includes bones, now or later, because the maker rules them out entirely.
Buying guide
A raw-food grinder purchase turns on four stated facts: the bone list, the plate set, the output figure and the cleaning method. Read each maker’s page for those four lines before anything else, and let the stated bone list, not the motor figure, set the ceiling for what goes through the head.
Start with the maker’s stated bone list
The bone list on a product page is a ceiling, not a suggestion. Match the bones in your batches to the bones the maker names, word for word: chicken on the LEM and VEVOR pages, chicken plus rabbit, squirrel and quail on the STX page. A bone type the maker does not name sits outside the stated capacity, whatever the wattage.
This is also where honest boneless models earn respect. A maker who prints not for bones beside a pet food claim gives the buyer a clean line to plan around. Trouble starts when a buyer reads a general power claim as a bone rating the maker never gave.
How meat grinders for raw dog food differ in plate sets
Plates decide the texture of a raw batch, and the sets here range from three plates on the BigBite #8 to six on the Turboforce II 4000. Where a maker states sizes in millimeters, 4.5mm reads as the fine plate and 10mm as the coarse plate across both the LEM #32 and the VEVOR #12, which makes batch planning direct.
Where a maker lists plates by name only, coarse and fine without numbers, the buyer chooses texture by eye and habit. Neither approach is wrong, but they suit different cooks: number-led buyers get repeatability from stated sizes, while name-only sets ask for some trial across the first batches.
Read throughput in the maker’s own units
Output figures only compare cleanly inside one maker’s unit system. LEM and VEVOR state pounds per minute, from about 7 on the #8 to approximately 17 on the #32, while STX states 175 to 225 pounds per hour on high speed. Quoted side by side without conversion, the numbers mislead; read each as the maker’s own claim for steady feeding.
What matters in the kitchen is rhythm: a stated figure roughly double another model’s means batch day runs in larger, fewer loads. Features that support long runs count beside the headline number, including reverse gears, circuit breakers or reset buttons, and named cooling systems such as the four-intake air cooling on the STX.
Materials and cleanup shape weekly effort
Raw batches repeat weekly, so the cleaning line on a spec sheet matters as much as the output line. Stainless steel heads, knives and augers on the LEM and VEVOR models shrug off repeated washing, and VEVOR goes further by listing its full parts set for dishwasher cleaning, a claim no other maker here makes for every part.
The STX takes the other road: a polished cast aluminum head the maker calls for hand washing, traded against the widest plate set on the list. Storage counts too. Drawers in the LEM bodies keep plates and tubes together between sessions.
Size the head and motor to the batch
Head size tracks batch size across this list: the #8 for moderate boneless batches, the #12 pair for mid-size bone-in work, and the #32 for the largest runs. Weight tracks head size with it, from 32.6 pounds on the #8 to 64.8 pounds on the #32, and that gap decides whether the grinder lives on the counter or travels from a cupboard.
Pan capacity matters: the LEM listings rate their pans at 7 lb, and the STX tray holds more than 3 pounds, so the #32’s speed still feeds from a pan that needs refilling. Match pan and output together, and batch day settles into a steady rhythm.
FAQ
Most questions about raw-food grinders come back to the same stated facts: which bones the maker names, which plates sit in the box, and how the output figure was measured. The answers below stay inside those stated lines, model by model, without stretching any maker’s wording past what its page says.
Can any of these grinders handle turkey bones?
No maker on this list names turkey bones. The stated bone lists stop at chicken bones on the LEM and VEVOR pages, and at chicken, rabbit, squirrel and quail on the STX page. Treat turkey bones as outside the stated capacity of all five models, and keep them out of the head.
That follows the only evidence a buyer can lean on: the maker’s own printed list. A grinder that earns a turkey-bone claim will print it, and none of these five does.
Which bones do the makers actually name?
Chicken is the common thread: both LEM BigBite models and the VEVOR #12 name chicken bones, and LEM phrases its #12 wording as raw chicken bones. STX names the widest list, soft bones such as chicken, rabbit, squirrel and quail, for the Turboforce II 4000 and its stated pet diet use.
Beyond those names, the pages go quiet. No maker here names beef, pork or lamb bones, and the BigBite #8 names the opposite, not for bones at all. Plan batches inside the named lists and the hardware stays inside its stated design.
What size batches suit meat grinders for raw dog food?
Match the batch to the stated output and the pan. The BigBite #8, at about 7 pounds per minute with a 7 lb rated capacity, suits a moderate weekly batch. The #12 models, at up to 11 pounds per minute, suit mid-size runs, and the #32, at approximately 17 pounds per minute, suits the largest grinding days.
The STX states its output by the hour, 175 to 225 pounds on high speed, which points the same way: long, steady sessions. The stated figures assume steady feeding of prepared pieces, so preparation pace often sets the real length of batch day.
Does a boneless grinder still fit raw batches?
Yes, when the batch itself is boneless and the maker says so. LEM states the BigBite #8 processes meat for pet food and bulk meal prep at about 7 pounds per minute, which covers boneless raw mixes of meat and organs ground at home. The same listing states the model is not for bones, so the fit ends exactly there.
A boneless grinder fits raw work when its maker names pet food preparation, and it stops fitting the day the recipe adds bone. Households unsure about future bone-in batches will find the #12 models the steadier ground.
What does a reverse gear do on a grinder?
Reverse runs the auger backward, which backs material out of the head so a dense or stalled load can be cleared and fed again. The STX builds it into a three-speed system with High and Low beside it, which gives the operator a low gear for heavy loads and a way back from a jam without opening the head.
Not every maker here states a reverse gear, and its absence simply changes how a stall gets handled, by hand with the head opened. Bone-in grinding makes reverse worth weighing, because dense loads stall more often than boneless ones.
Conclusion
Bone-in batches point to the LEM BigBite #32 or the STX Turboforce II 4000, boneless batches to the LEM BigBite #8, and mid-size runs to the #12 pair. Each pick rests on its maker’s printed wording. No model here states a bone beyond chicken and smaller soft bones, so let that stated ceiling, not motor size, make the final call.