Key takeaways
- Compare kitchen sinks with drainboard by bowl size, cabinet width and board layout, from a compact 33 inch drop-in to a 48 inch sink top and a metric inset.
A drainboard built into the sink gives wet dishes a place to sit without a rack taking counter space. This guide compares kitchen sinks with drainboard models whose maker pages state the board as part of the sink, in drop-in, sink top and inset formats, at widths from 33 inches to 88 cm, with their stated cabinet sizes set side by side.
Quick verdict
Short on patience? The short answer is that the drainboard format is a narrow one: most verified picks here are stainless drop-in models from one long-running maker line, plus one metric inset sink. Match the sink width to your cabinet first, then pick bowl count and board side.
If your cabinet run is modest, the 33 inch Elkay ILR3322R is the only pick here that fits a 36 inch cabinet. If you wash large pans by hand, the 43 inch ILR4322L gives you a 22 inch long single bowl, and the 48 inch ILR4822L splits the width into two equal bowls beside the board. The S4819R4 takes a different route: it is a 48 by 25 inch sink top, so the sink and its board form the counter section itself. The IKEA VATTUDALEN is the metric option, an 88 by 53 cm inset sink with a sloping board and a 1-1/2 bowl layout.
Every model below is one whose maker page names a drainboard as part of that model. Workstation ledges, add-on racks and separate trays are not counted as drainboards here, and models whose pages never state the feature are left out.
| Product | Format | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Elkay Lustertone Classic ILR3322R | Drop-in, single bowl | Small kitchens | 33 x 22 in top, 36 in minimum cabinet | 16 in bowl, 7-1/2 in deep |
| Elkay Lustertone Classic ILR4322L | Drop-in, single bowl | Large pans and trays | 22 x 16 in bowl | Needs a 48 in cabinet |
| Elkay Lustertone Classic ILR4822L | Drop-in, double bowl | Full hand washing loads | Two 13-1/2 x 16 in bowls | Needs a 51 in cabinet |
| Elkay Lustertone Classic S4819R4 | Sink top, single bowl | Counter replacement | 48 x 25 in top, rear center drain | Mounting hardware not included |
| IKEA VATTUDALEN | Inset, 1-1/2 bowl | Metric cabinetry | 88 x 53 cm, sloping board | Bowl dimensions not stated by the maker |
How we selected
Every model in this guide earned its place from its maker’s own published pages. The maker spec sheet or product page had to name a drainboard as part of that exact sink model, and every size, gauge and cabinet figure quoted in this guide is printed on one of those pages.
That bar cut the field hard: several farmhouse sinks with board-shaped sections beside the bowl were set aside because their maker documents dimension the section without ever naming it a drainboard. One workstation line sold under drainboard wording elsewhere is described by its maker’s own sheet as a ledge with a cover board, so it is not here either. What remains is a short list that leans heavily on one maker, because that maker still publishes a full drainboard range with complete sheets.
Within the list, models were spread across the decisions a buyer faces: width from 33 to 48 inches, single bowl against double bowl, a drop-in rim against a full sink top, and one metric inset design. Where a sheet leaves a figure unstated, such as a separate board width, this guide says so rather than estimating it.
The kitchen sinks with drainboard in this guide
Five models met the bar, and they split into three formats: four stainless models from the same maker line in widths from 33 to 48 inches, and one metric inset sink with a sloping board. Read each entry for the cabinet width it demands before anything else, because that figure decides most of these picks.
Elkay Lustertone Classic ILR3322R single bowl drop-in sink with drainboard
The compact pick of the set, the ILR3322R is a 33 by 22 inch drop-in sink for kitchens that cannot give a drainboard model a wide cabinet run. The maker sheet lists the special feature plainly as drainboard, and the single bowl leaves the rest of the top as board space beside it.
The sheet lists 18 gauge type 304 stainless steel with a Lustrous Satin finish. The bowl measures 16 by 16 by 7-1/2 inches with a center drain opening of 3-1/2 inches, and sound deadening is bottom only pads. The stated minimum cabinet size is 36 inches. For the install, the cutout is 32-3/8 by 21-3/8 inches with a 1-1/2 inch corner radius, mounting hardware is included for countertops up to 3/4 inch thick, and the template is not included, though it is listed for download as template 1000001189. The sheet lists compliance with ASME A112.19.3 and CSA B45.4, and optional accessories include the CB1713 and CBS1316 cutting boards, the LK99 strainer and the LKWRB1316SS rinsing basket.
The limits are size and depth. A 16 inch square bowl is tight for sheet pans and large stock pots, and 7-1/2 inches is the smallest bowl depth in this guide. The sheet does not state a separate drainboard width, so the usable board area can only be judged from the overall width against the 16 inch bowl.
- Pros: smallest cabinet demand in this guide at 36 inches; mounting hardware included; cutting board and rinsing basket accessories listed by the maker.
- Cons: 16 inch bowl limits large cookware; bowl depth of 7-1/2 inches; template not included.
- Buy if: your cabinet run is 36 inches and you still want a built-in board for glasses and small loads.
- Skip if: you hand wash roasting pans or tall pots often, or your counters are thicker than 3/4 inch and you do not want to source longer mounting hardware.
Elkay Lustertone Classic ILR4322L single bowl drop-in sink with drainboard
The ILR4322L stretches the same format to 43 by 22 inches, and the extra width goes to the bowl: at 22 by 16 inches, it is the longest single bowl in this guide. For a household that hand washes oven trays and grill pans, this is the drainboard model shaped around that job.
Specs from the maker sheet match the smaller model in construction: 18 gauge type 304 stainless steel, Lustrous Satin finish, a center drain opening of 3-1/2 inches, and bottom only pads for sound deadening. Bowl depth is again 7-1/2 inches. The trade for the longer bowl is cabinet width: the stated minimum cabinet size is 48 inches. The cutout is 42-3/8 by 21-3/8 inches with a 1-1/2 inch corner radius, mounting hardware is included for countertops up to 3/4 inch thick, and the template, number 1000001286, is not included. The sheet lists ASME A112.19.3 and CSA B45.4 compliance, and the accessory list adds the LKWBG2115SS bottom grid alongside the CB1713 and CBS1316 cutting boards and the LK99 strainer.
The limit to weigh is the 48 inch cabinet demand for a sink that still gives one bowl at 7-1/2 inches deep. If two people wash and dry at once, a double bowl may serve better; if depth matters more than length, no stainless pick here goes deeper.
- Pros: 22 inch long bowl takes trays and pans the 33 inch model cannot; bottom grid listed as an accessory; hardware included.
- Cons: needs a 48 inch cabinet; single bowl only; template not included.
- Buy if: you have a wide cabinet run and wash large flat cookware by hand.
- Skip if: your cabinet is under 48 inches, or you want a second bowl for soaking while you wash.
Elkay Lustertone Classic ILR4822L double bowl drop-in sink with drainboard
At 48 by 22 inches, the ILR4822L is the double bowl entry: two equal bowls sit beside the board, so one side can hold wash water while the other rinses, and clean pieces move straight onto the board to drain. It is the pick for households that still do full loads by hand.
The maker sheet lists 18 gauge type 304 stainless steel in a Lustrous Satin finish, with each bowl at 13-1/2 by 16 by 7-1/2 inches and a center drain opening of 3-1/2 inches per bowl. Sound deadening is bottom only pads. The minimum cabinet size is 51 inches. The cutout measures 47-3/8 by 21-3/8 inches with a 1-1/2 inch radius, mounting hardware is included for countertops up to 3/4 inch thick, and the template is not included. Accessories listed include the LKWBG1316SS bottom grid, the CB1613, CB1713 and CBS1316 cutting boards and the LK99 strainer, and the sheet lists compliance with ASME A112.19.3 and CSA B45.4.
Two limits stand out. A 51 inch cabinet is a serious run of base cabinetry, and each bowl, at 13-1/2 inches wide, is narrower than the single bowl of the 33 inch model, so the biggest pans still will not sit flat. The board also shares a 48 inch top with two bowls, so drying space per load is modest.
- Pros: two equal bowls plus a board in one top; grid and three cutting board options listed; hardware included.
- Cons: 51 inch minimum cabinet; individual bowls are narrow; template not included.
- Buy if: you wash and rinse in separate bowls and have the cabinet width to spare.
- Skip if: your cabinet run is under 51 inches, or your cookware is mostly oversized pans.
Elkay Lustertone Classic S4819R4 single bowl sink top with drainboard
The S4819R4 is built differently from the drop-in models above: the maker lists its installation type as sink top, so the 48 by 25 inch stainless unit forms the work surface itself, with the bowl and drainboard formed into one top instead of a sink set into a cutout.
The sheet lists 18 gauge 304 stainless steel with a Lustrous Satin finish. The single bowl measures 19 by 16 by 7-1/2 inches, and the drain placement is rear center with a 3-1/2 inch opening. Sound deadening is sides and bottom pads, the fullest padding listed among these stainless models. The minimum cabinet size is 48 inches. Maker custom options include type 316 stainless steel, right rear or left rear drain locations, and a version with the bowl on the opposite side. Compliance is listed as ASME A112.19.3 and CSA B45.4, and accessories include the CB1713 and CBS1316 cutting boards, the LK99 strainer and the LKWERBSS and LKWRB1418SS rinsing baskets.
Read the fine print first: mounting hardware is not included, and no template is included. At 25 inches, this top is also deeper front to back than the 22 inch drop-in models, so counter depth and the cabinet below need measuring, not assuming.
- Pros: one formed top with no cutout rim seam around a separate sink; rear center drain; sides and bottom pads; type 316 option listed.
- Cons: mounting hardware not included; 25 inch depth will not suit every counter run; single bowl only.
- Buy if: you are replacing a counter section anyway and want the sink and board as one surface.
- Skip if: you want a standard drop-in swap into an existing cutout, or your counter depth is a strict 25 inches with no overhang room.
IKEA VATTUDALEN inset sink, 1-1/2 bowl with drainboard, 88 x 53 cm
The VATTUDALEN is the metric entry in this guide, an inset sink at 88 by 53 cm with a 1-1/2 bowl layout. The maker describes the board directly: this sink has a sloping drainboard, so that excess water from dishes flows back into the bowl, which is the clearest board description on any page in this set.
The maker page states that the sink can be under-glued, that it fits cabinet frames a minimum of 60 cm wide, and that it carries a 25 year guarantee. The half bowl gives a second, smaller water space beside the main bowl, which suits rinsing glasses or draining cutlery while the main bowl is full. Every figure on the maker page is in centimeters, and the page does not state bowl dimensions or a steel thickness, so neither is quoted here.
The limits follow from that. A 53 cm deep inset is deeper front to back than most US drop-in sinks, the cabinet figure is a frame width rather than the cabinet sizes the other makers quote, and anyone working in inches will be converting every measurement twice, once for the cutout and once for the cabinet. Treat the conversion as part of the install plan, not a detail.
- Pros: sloping board with the flow path stated by the maker; 1-1/2 bowl layout; 25 year guarantee listed; can be under-glued.
- Cons: metric dimensions throughout; bowl dimensions and steel thickness not stated on the maker page; deeper front to back than the US models here.
- Buy if: you are building around metric cabinetry and want the second half bowl for rinsing.
- Skip if: you need inch-based spec figures for a US cabinet order, or a stated steel gauge before you buy.
Buying guide
A drainboard sink is bought on three measurements before anything else: the overall width of the top, the minimum cabinet the maker states, and the bowl size left over after the board takes its share. The five models here show how sharply those numbers move together, so work through them in that order.
Counter space trade-offs with kitchen sinks with drainboard
Every inch of board is an inch the bowl does not get, and the trade is visible across this list: the 33 inch model pairs its board with a 16 inch bowl, while the 48 inch double bowl splits what is left into two 13-1/2 inch bowls. Decide which side of that trade your washing habits sit on before you fall for a width.
Think about what actually dries at your sink. A household running a dishwasher dries little more than glasses, a pan and a board, and a compact model covers that. A household washing full loads by hand needs board area for plates to stand, and the wider tops earn their width. Buying the wide top for dishwasher loads gives up counter run you will miss, and buying the compact top for hand washing leaves wet dishes on towels.
Drop-in rim or full sink top: two ways the board is built
Four models here are drop-in sinks: a rim sits on the counter around a cutout, and the stated cutout sizes and the 3/4 inch countertop limit on the included hardware are part of the deal. The fifth, the S4819R4, is a sink top, where the unit is the surface, at 48 by 25 inches with hardware not included.
The drop-in route is the simpler replacement, because the counter stays and the sink swaps. The sink top route makes sense during a counter replacement or a utility room build, where forming the bowl and board in one piece removes the rim seam that traps crumbs and water on a drop-in. Price the hardware and the counter work into the sink top choice, since the sheet leaves mounting hardware off the included list.
Left or right: fixing the board side before the cutout
On the Elkay sheets, the drainboard sits on one side of the bowl, and each sheet notes that similar models are available with the drainboard on the opposite side. That one line matters more than most specs: the board side decides where wet dishes sit relative to your dishwasher, your drying hand and your stove.
Stand at your current sink and act out a wash load. The board belongs on the side your clean hand reaches for, clear of a tall faucet arc or a window sill. Order the variant that matches: a drop-in cutout is not reversible once cut, and the opposite-side model is a different order, not a rotation of the same sink.
Bowl depth and board slope do different jobs
All four stainless models here list a bowl depth of 7-1/2 inches: tall glasses and pans fit, but a deep stock pot will stand proud of the rim. If your washing is mostly deep pots, treat that shared figure as a class limit of the format rather than a flaw in one model.
Slope is the board-side question. The IKEA page states that its board slopes so water flows back into the bowl. The Elkay sheets name the drainboard as a special feature without describing a slope in text. If a drained puddle under the dish rack is your current annoyance, a stated slope is the spec to insist on; if the board is mostly a landing zone wiped down after use, the flat statement of the feature may be enough.
Cabinet width is the first measurement, not the last
The stated minimum cabinet sizes in this guide run from 36 inches for the 33 inch sink to 51 inches for the 48 inch double bowl, with the metric model quoting a 60 cm cabinet frame. Those figures come from the maker sheets, and they are the first filter: a sink whose minimum cabinet beats your run is out, whatever its bowl offers.
Measure the inside of the cabinet, not the door front, and allow for sink clips, supply lines and a disposal if one is fitted. The drop-in sheets include mounting hardware for countertops up to 3/4 inch thick, so a thicker stone top changes the hardware as well. Confirm both numbers before the order, not at the install.
FAQ
These are the questions that come up once the shortlist is down to real models: how the board handles water, how it cleans, what it replaces, and which stated figures to trust. Each answer sticks to what the maker pages for these five models actually say, plus general care practice.
Are kitchen sinks with drainboard hard to keep clean?
Not especially. The board is the same material as the rest of the top on every model here, stainless steel on the four Elkay models, so it wipes down with the same routine as the bowl. The grooves and the slope that move water are also the places crumbs settle, so a brush along the board lines during the weekly clean keeps them clear.
The real limit is water behavior, not effort. A board that slopes, as the maker describes for the VATTUDALEN, sends rinse water back to the bowl. A board without a stated slope holds a thin film until it is wiped or evaporates. Neither is a defect; the spec sheet tells you which version you are buying if you read for the slope line.
Can a built-in drainboard replace a counter dish rack?
For the loads these sinks are sized for, yes: the board is a fixed drying surface that never needs storing, and on the wider models it holds a full rack’s worth of plates and glasses. That is the core appeal of the format, and it is why the width trade against bowl size is worth making deliberately.
Where a rack still wins is vertical storage: it stacks plates in slots, while a flat board takes them leaning or lying, using more surface per plate. Households that dry tall stacks after big meals may keep a rack for overflow and use the board for the daily load, which is how most owners settle into the format.
Is a sink top the same as a drop-in sink with a drainboard?
No, and the difference is in the install, not the washing. A drop-in model, like the three ILR sinks here, sets into a cutout with its rim on the counter, using the cutout sizes the sheets state. A sink top, like the S4819R4, replaces that section of counter outright: the 48 by 25 inch unit is the surface.
Choose the drop-in when the counter stays and the job is a sink swap; choose the sink top when the counter is being built or replaced anyway. Either way, note the hardware line on the sheets: drop-in models include mounting hardware for tops up to 3/4 inch thick, while the sink top lists it as not included.
What cabinet sizes do these drainboard models need?
The maker sheets state them model by model: 36 inches minimum for the 33 inch ILR3322R, 48 inches for the 43 inch ILR4322L, 51 inches for the 48 inch ILR4822L, and 48 inches for the S4819R4 sink top. The VATTUDALEN is quoted against cabinet frames a minimum of 60 cm wide.
Notice that cabinet size does not track sink width one to one: the 43 and 48 inch models differ by three inches of cabinet demand, and the double bowl needs the most room of all. The cabinet figure printed on each sheet is the number to shop by, and a tape measure inside your base cabinet settles which of these five models are even candidates.
Does the drainboard need its own drain or plumbing?
No separate drain is listed for any model here. The drain openings the sheets state, 3-1/2 inches on the stainless models, are the bowl drains, and the board is a surface, not a plumbed fixture. On the sloping design, the maker states that excess water from dishes flows back into the bowl, which is the whole drainage plan.
That also means the board cannot rescue a badly leveled install: set a drop-in top with a tilt away from the bowl and water sits or runs to the rim instead. A level check across the top before the clips are tightened is the entire fix, and it costs nothing at install time.
Conclusion
Buy the ILR3322R for a 36 inch cabinet, the ILR4322L for big pans, the ILR4822L for two-bowl hand washing, the S4819R4 when the counter itself is being replaced, and the VATTUDALEN for a metric run with a stated slope. Measure the cabinet first; the right drainboard sink is the one that fits it and puts the board on your working side.