Key takeaways
- Renovation sinks compared on mount type, cabinet size and included parts: drop-in and dual mount models that keep a counter, plus undermount and apron picks.
A renovation sink is chosen under constraints the old kitchen sets: a counter that may stay, a cutout that already exists, and cabinets that are not moving. This guide compares sinks for kitchen renovation projects on mount type, minimum cabinet size, bowl depth and included parts, from each maker page.
Quick verdict
If the counter stays, start with the three models that mount from above: the Delta Lorelai 95A932-33S-SS drop-in workstation, the Kraus KHTC300-32 dual mount, and the Elkay Quartz Classic ELGR13322 drop-in. Each one covers or fills an existing cutout instead of asking for a new counter.
If the counter is being replaced, the set opens up. The Kohler Whitehaven K-6488 brings an apron front into standard cabinetry with a shortened, self-trimming apron, and the Delta Lorelai 95B932-32S-SS and Kraus Kore KWU110-32 add undermount workstation bowls with ledges and full accessory kits. Cabinet figures run from 33 inches for the Kraus dual mount to 36 inches for the other five, so the cabinet check comes before everything else in a renovation.
The material spread is wide for a six-sink set: four stainless steel models in 16 gauge, one quartz composite in six finishes, and one enameled cast iron apron sink. The two Delta kits and the Kraus models list grids, drain assemblies and templates in the box, while the Elkay quartz sheet lists its grid and drains as optional accessories and the Kohler sheet lists its strainer as a recommended extra.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Delta Lorelai 95A932-33S-SS | Drop-in workstation, stainless steel | Keeping the counter, gaining a ledge | 33 x 22 in., bowl depth 9 in., cabinet 36 in. | Needs a 36 inch cabinet |
| KOHLER Whitehaven K-6488 | Undermount apron front, cast iron | An apron look in standard cabinetry | Shortened Self-Trimming apron, bowl 30-3/4 x 18-1/16 in. | Strainer listed as a separate accessory |
| Kraus KHTC300-32 | Dual mount, stainless steel | Deciding the mount at install time | Cabinet 33 in., 4mm deck, 2 pre-drilled holes | Smaller bowl than the 33 inch models |
| Elkay Quartz Classic ELGR13322 | Drop-in quartz composite | A color change without a new counter | 33 x 20-7/8 in., six finishes, rear center drain | Template not included; grid and drains optional |
| Delta Lorelai 95B932-32S-SS | Undermount workstation, stainless steel | A ledge sink with a new counter | 32 x 19 in., bowl 30 x 16 x 9 in., cabinet 36 in. | Undermount only; counter must be replaced or new |
| Kraus Kore KWU110-32 | Undermount workstation, stainless steel | The deepest bowl in the set | Bowl depth 10 in., rear offset drain, full kit | Cabinet 36 in. left to right |
How we selected
Each model had to answer a renovation question on its own page: a mount that works with an existing counter or cutout, an apron built to retrofit standard cabinetry, or an undermount kit complete enough to anchor the new-counter side of a project. Pages that stated no mount type or no cabinet figure were left out.
The set was then balanced across the two renovation paths. Three models keep the counter: a drop-in workstation, a dual mount that can go either way on the day, and a drop-in quartz sink that changes the kitchen’s color without touching the counter. Three models assume a new counter: the apron-front cast iron sink and two undermount workstations. Every model here is a single bowl; the double bowl candidates either repeated models used in this project’s remodel guide or lacked a full stated spec set.
Figures are quoted from the page behind each profile, including the awkward ones. Where two documents disagree, the profile follows the maker page and the disagreement is a reason to confirm the figure at order time, not a detail to smooth over. Warranty lines are reported as the makers print them: limited lifetime on the Delta, Kraus and Kohler pages used here.
Sinks for kitchen renovation projects, profiled
The profiles follow the renovation order of decisions: what happens to the counter, what the cabinet allows, and what arrives in the box. Kit contents matter more in a renovation than in a new build, because a missing strainer or template lands in the middle of a kitchen that is already torn apart.
Delta Lorelai 95A932-33S-SS drop-in workstation sink
This is the keep-the-counter workstation: a 33 by 22 inch drop-in in TRU16 gauge stainless steel with a SatinSheen finish, a bowl of 29.88 by 16 by 9 inches, and a stated minimum cabinet size of 36 inches. The mounting deck is a heavy-duty 4mm deck with 2 pre-drilled holes, per the maker page.
The renovation value is the kit. The page lists an acacia cutting board with a mobile device holder, a roll-up drying rack with a utensil holder, a stainless steel bottom grid, and a drain assembly with a removable cover, plus all mounting hardware and a cut-out template. The WorkFlow ledge turns the sink into a prep surface, which is how a renovation that cannot add counter space still gains some. The maker also states the chromium to nickel ratio as 18:10 and confirms on the page that its drop-in sinks work with a laminate counter.
The limits are the cabinet and the footprint. A 36 inch minimum cabinet is the largest figure in this set, and a 33 by 22 inch top-mount deck needs an existing cutout close to that size or a counter that can be cut back. The page also notes an accessory hole on the right side of the deck for a soap dispenser or air gap, but the deck pattern is fixed: 2 pre-drilled holes plus that accessory hole.
- Pros: full workstation kit in the box; drop-in mount keeps the existing counter; rear-offset drain frees cabinet space per the maker; hardware and template included.
- Cons: 36 inch minimum cabinet; single bowl; fixed deck hole pattern.
- Buy if: your counter and 36 inch cabinet stay, and you want the workstation ledge without new stone.
- Skip if: your cabinet is under 36 inches, or your existing cutout is far from 33 by 22 inches.
KOHLER Whitehaven K-6488 apron-front sink
The Whitehaven is the renovation route to a farmhouse look without custom cabinets. Kohler’s sheet describes a 35-1/2 inch undermount single bowl in enameled cast iron, with a bowl area of 30-3/4 by 18-1/16 inches, a bowl depth of 9 inches, and a 36 inch minimum base cabinet width.
The apron design is the whole point. The sheet states that the shortened apron allows the sink to be used in most standard cabinetry or retrofitted to existing standard cabinetry, and that the Self-Trimming apron overlaps the cabinet face for the installation. In renovation terms, that means the cabinet front is cut down rather than replaced, and the apron covers the cut edge. The sheet also lists an offset drain, which it describes as increasing workspace in the sink and storage space underneath, and a bowl that slopes toward the drain. A cut-out template is listed as required and included.
The conditions are printed on the same sheet. The distance from the top edge of the cabinet to the top of the cabinet door must be at least 6-7/8 inches for this sink to install, the drain hole is 3-5/8 inches rather than the 3-1/2 inch size used by the steel models here, and the sink drain and strainer appear on the sheet as recommended accessories, not as included parts. The sheet does not print a weight figure, so the support plan for a cast iron sink has to come from the installer rather than the page.
- Pros: apron front retrofits standard cabinetry per the maker; self-trimming apron covers the cabinet cut; offset drain; template included.
- Cons: strainer is a separate accessory; 3-5/8 inch drain hole; needs the stated door clearance figure; undermount, so the counter is replaced or new.
- Buy if: you want the apron look in a renovation that keeps standard cabinets.
- Skip if: your cabinet front cannot meet the clearance figure on the sheet.
Kraus KHTC300-32 dual mount sink
The KHTC300-32 is the flexible option: a dual mount sink that installs as a drop-in or an undermount, with outer dimensions of 31-1/4 by 20-1/2 by 9-1/2 inches, a bowl of 28-1/2 by 15-1/4 by 9 inches, and the smallest minimum cabinet figure in this set at 33 inches.
The listing describes it as a drop-in and undermount sink ideal for retrofitting, and states that it installs with any kind of countertop when installed as a top mount. That one sentence is the renovation case: the sink can be ordered before the counter decision is final, dropped in if the counter stays, or undermounted if the project grows. The build is 16 gauge stainless steel with a satin finish, a thick 4mm deck with a beveled edge, and 2 pre-drilled holes for a faucet and an accessory. The kit lists the sink, a stainless bottom grid, a drain assembly and cover, mounting hardware and cut-out templates.
The trade is bowl size. At 28-1/2 by 15-1/4 inches, the bowl is the smallest in this set, a step down from the 33 inch models on both axes, and the rear-set drain that frees the work surface also fixes the plumbing position at the back of the cabinet. Buyers with a 33 inch cabinet gain a real option here, but buyers with a 36 inch cabinet give up bowl room they did not have to give up.
- Pros: dual mount defers the counter decision; 33 inch minimum cabinet, the smallest here; full kit with grid, drain assembly and templates; 16 gauge steel.
- Cons: smallest bowl in the set; rear-set drain fixes the plumbing layout; one listing’s weight fields disagree, so confirm shipping details at order time.
- Buy if: your renovation has a 33 inch cabinet or an undecided counter.
- Skip if: you have room for a 33 inch sink and want the larger bowl.
Elkay Quartz Classic ELGR13322 drop-in sink
The ELGR13322 changes how the kitchen looks without changing the counter: a 33 by 20-7/8 inch drop-in in quartz composite, with a bowl of 30-1/4 by 16-5/16 by 9-7/16 inches, a rear center drain, and a stated minimum cabinet size of 36 inches. Its bowl is also the deepest of the three counter-keeping models in this set.
Elkay’s sheet states the sink is molded with up to 80 percent natural quartz and high performance acrylic resins, and describes the material as non-porous with heat, scratch, fade and stain resistance in the maker’s wording. The finish list is the renovation lever: Black, Dusk Gray, Graphite, Greystone, Matte Black and White, so the sink can carry a color change that a stainless model cannot. The sheet also states the mounting hardware is included for countertops up to 1-3/4 inches thick, and prints the drop-in cutout at 32-3/8 by 20-1/4 inches with an 11/16 inch corner radius, which lets a renovator measure the existing hole against a stated figure.
Read the included column carefully. The sheet states the template is not included and must be downloaded, and it lists the bottom grid and the drain fittings as optional accessories, so the installed total adds a drain at minimum. The compliance line also differs from the steel models: the sheet lists CSA B45.8 and IAPMO Z403 for this quartz sink.
- Pros: six finishes for a color-led renovation; stated cutout dimensions to check against the old hole; mounting hardware included; deep 9-7/16 inch bowl.
- Cons: template not included; grid and drains are optional extras; 36 inch minimum cabinet.
- Buy if: the counter stays but the kitchen needs a visible change, and the existing cutout matches the stated figure.
- Skip if: you want every fitting in the box, or your cutout is well off the stated size.
Delta Lorelai 95B932-32S-SS undermount workstation sink
The undermount Lorelai is the new-counter counterpart to the drop-in model above: 32 by 19 by 9.5 inches in TRU16 gauge stainless steel with a SatinSheen finish, a bowl of 30 by 16 by 9 inches, and a minimum cabinet size of 36 inches as stated on the maker page.
The kit mirrors the drop-in version and adds one piece: an acacia cutting board with a mobile device holder, a roll-up drying rack with a utensil holder, a silicone drying mat, a stainless steel bottom grid, and a drain assembly with a removable cover, with hardware and a cut-out template included. The WorkFlow ledge and the rear-offset drain carry over, as do the NoiseDefend soundproofing and the cUPC certification the maker lists. In a renovation with new stone or quartz counters, this is the model that turns the sink bay into the prep zone the old kitchen never had.
The constraints are the mount and the cabinet. Undermount installation belongs to the counter replacement path, with the faucet drilled through the new counter, and the 36 inch cabinet figure matches the drop-in model. One caution: a marketplace listing for this model prints a smaller cabinet figure than the maker page, so plan the cabinet around the 36 inch figure on the Delta page.
- Pros: fullest kit in the set, including the silicone drying mat; ledge workstation; 30 inch bowl; template and hardware included.
- Cons: undermount only; 36 inch cabinet; cabinet figures differ between the maker page and a marketplace listing.
- Buy if: the renovation includes a new counter and a 36 inch cabinet.
- Skip if: the counter stays, where the drop-in Lorelai is the same idea in the right mount.
Kraus Kore KWU110-32 undermount workstation sink
The Kore KWU110-32 is the deep-bowl undermount: a 32 by 19 inch workstation sink with a bowl of 30 by 16 inches and a stated sink depth of 10 inches, the deepest in this set, in 16 gauge stainless steel with a rear off-set drain. The sheet presents it as a workstation model with an accessory ledge.
Kraus’s sheet is unusually complete about the box. Accessories listed as included are the strainer ST-1, a cover cap STC-2, a bottom grid KBG-UN1-32, a rolling mat KRM-11BL and a cutting board KCB-WS103BB, plus a cut-out template and mounting hardware. The cabinet requirement is stated in two directions, 36 inches left to right and 24 inches front to back, which is the kind of figure a renovator can check against an existing cabinet carcass in one visit. The sheet also lists NoiseDefend undercoating and sound dampening pads, a 3 1/2 inch drain opening, and cUPC certification to ASME A112.19.3 and CSA B45.4.
The limits are the usual undermount ones, plus depth itself. A 10 inch bowl lowers the drain line and the disposal further into the cabinet, which matters where the wall drain height is fixed. The workstation ledge accessories are the maker’s own sizes, so the rolling mat and board are replacement purchases from the same range later.
- Pros: 10 inch bowl depth; every accessory named on the sheet is included; cabinet figure stated in two directions; rear off-set drain.
- Cons: undermount only; deep bowl lowers the plumbing in the cabinet; ledge accessories are maker-specific sizes.
- Buy if: the renovation replaces the counter and you want depth plus a complete kit.
- Skip if: your drain line enters the wall high and cannot move.
Buying guide
Renovation buying starts from what is already in the room. The counter decision, the existing cutout, the cabinet width and the wall drain height are fixed facts, and the sink is the part that bends. The checks below follow that order, using the figures printed on the six pages behind this guide.
Decide the counter question before sinks for kitchen renovation picks
The counter decision divides this set in half. Drop-in and dual mount models, the Delta drop-in Lorelai, the Kraus KHTC300-32 and the Elkay ELGR13322, sit in or over an existing cutout and keep the counter. Undermount models, the Whitehaven, the undermount Lorelai and the Kore, hang below the counter and need it replaced or new.
Make that call before comparing bowls, because it also sets the faucet plan. The drop-in Delta and the dual mount Kraus carry pre-drilled deck holes, 2 on each page, while every undermount here puts the faucet holes in the new counter. A renovation that keeps the counter but wants a new faucet pattern may find the deck holes decide the question on their own.
Measure the existing cutout against a stated figure
Only one page in this set prints its drop-in cutout as a figure: the Elkay sheet gives 32-3/8 by 20-1/4 inches with an 11/16 inch corner radius. The Delta and Kraus kits include cut-out templates instead, which work when the counter can be trimmed but not when the existing hole is already larger than the sink deck.
The field check is simple. Measure the existing hole at its widest points, including any chipped or routed corners, and compare it with the sink’s overall size and deck. A drop-in deck has to cover the hole with bearing surface all the way around; a hole that breaks that ring is a counter repair job, not a sink choice.
Use the cabinet figure as the second gate
Stated minimum cabinets here run from 33 inches for the Kraus dual mount to 36 inches for the other five models, and the Kore sheet adds a second direction at 24 inches front to back. In a renovation the cabinet is a fixed box, so these figures are pass or fail in a way they are not in a new kitchen, where the cabinet order can still change.
Measure the cabinet interior width between the side panels, and check the front rail and any drawer box above the sink bay. Apron models add their own condition: the Kohler sheet requires at least 6-7/8 inches from the top edge of the cabinet to the top of the cabinet door, a figure that rules some framed cabinets out before width is even considered.
Check the drain height before choosing a deep bowl
Bowl depth in this set runs from 9 inches to the 10 inches of the Kraus Kore, and every inch of depth moves the drain and the disposal down by roughly that inch. In an older kitchen, the waste line often enters the wall at a height set decades ago, and a deeper bowl can leave the drain outlet above the trap arm.
The pages give the drain positions to plan around: rear-offset drains on both Delta models and the Kraus Kore, a rear-set drain on the dual mount Kraus, a rear center drain on the Elkay, and an offset drain on the Whitehaven. Rear and offset positions buy working room in the cabinet, but they do not change the height question, which is measured from the floor to the wall opening.
Price the renovation on sink plus missing parts
The kits split this set into two cost shapes. The Delta and Kraus models list grids, drain assemblies, templates and hardware in the box. The Elkay lists its grid and drains as optional accessories and its template as a download, and the Kohler lists its strainer as a recommended accessory, so both need extra parts before the sink can be used.
The honest renovation comparison is the installed figure: sink, drain fitting, grid if wanted, and any counter or cabinet work the mount requires, all counted before the order is placed.
FAQ
Renovation questions tend to be about fit rather than features: what the old counter allows, what the cabinet allows, and which parts still have to be bought. The answers below stay with the figures and wording printed on the six maker and listing pages behind this guide.
Can sinks for kitchen renovation projects reuse the old cutout?
Sometimes, and the drop-in models are built for exactly that case. The Elkay sheet prints its cutout at 32-3/8 by 20-1/4 inches, so the old hole can be measured against a stated figure. The Delta drop-in and the Kraus dual mount cover the hole with a deck instead, which forgives small differences but not a hole larger than the deck.
Does an apron sink need special cabinets in a renovation?
Not on the Kohler sheet. The Whitehaven’s shortened apron is described as allowing use in most standard cabinetry or retrofitting to existing standard cabinetry, with the Self-Trimming apron overlapping the cabinet face. The sheet’s condition is a clearance figure, at least 6-7/8 inches from the cabinet top edge to the top of the door.
Which model here fits the smallest cabinet?
The Kraus KHTC300-32, at a stated minimum cabinet size of 33 inches. The other five models in this set state 36 inches, including both Delta Lorelai versions, the Whitehaven, the Elkay quartz sink and the Kraus Kore, so a 33 inch cabinet narrows this list to a single model quickly.
Are the strainers included with these sinks?
It depends on the model, which is why the box contents are worth reading line by line. The Delta kits and both Kraus models list a drain assembly or strainer as included. The Elkay sheet lists its drains as optional accessories, and the Kohler sheet lists its sink drain and strainer as recommended products to buy separately.
Can a drop-in sink go into a laminate counter during a renovation?
For the Delta drop-in, the maker answers that question directly on the product page: its drop-in sinks work with a laminate counter. The Kraus dual mount listing makes the broader version of the same point, stating that the sink installs with any kind of countertop when it is installed as a top mount.
Conclusion
For a renovation, match the sink to the fixed decision: drop-in or dual mount models from Delta, Kraus and Elkay when the counter stays, and the Whitehaven apron sink or the undermount workstations from Delta and Kraus when it is replaced. Check the cabinet figure second, count the box contents third, and the right model picks itself.