Key takeaways
- Six Franke kitchen sinks compared on stated specs: Peak and Maris, Ellipse and a shallow accessible bowl, in stainless steel and Fragranite, with cabinet sizes.
A single maker can still leave a wide field to sort through. This guide compares sinks for kitchen franke kitchens across the maker’s stainless steel and Fragranite lines, using bowl size, bowl depth, minimum cabinet size and included parts exactly as printed on each Franke page for these six current models.
Quick verdict
Start with the cabinet, because this set splits cleanly on that one figure. The Franke Peak PKG11020SLG fits a 24 inch cabinet and the Ellipse ELG11022MBK fits a 27 inch cabinet, while the Maris MAG11031OW-ONY-CA and the Ellipse ELG120ONY-CA both ask for a 36 inch cabinet under a 33 inch sink.
Material is the second split. Two models are stainless steel: the Peak PKX11028-S in 16 gauge with a Diamond finish and an integrated ledge, and the shallow UCS6805P-1 in 18 gauge type 304 steel with a 5 inch bowl depth. Four models are Fragranite, the maker’s granite composite: the Maris single bowl, two Ellipse models in single and double bowl form, and the compact Peak granite sink with its own ledge. Every model in this set is an undermount on its page, so the counter material and the cutout work matter for all six.
Depth is the third split. The Maris bowl runs 9.496 inches deep and the Peak stainless bowl 9 5/8 inches, while the little UCS6805P-1 stops at 5 inches because its page describes an accessible design. Included parts also vary more than the shared brand suggests: the Maris and the double Ellipse list a strainer assembly in the box, the two other Fragranite models list none, and the Peak stainless sheet lists a drain cover and a strainer assembly as included accessories.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Franke Peak PKX11028-S | Stainless steel undermount, single bowl | A ledge workstation in steel | 16 gauge, bowl 27 3/16 x 16 1/2 in., depth 9 5/8 in. | Maker documents print different cabinet figures |
| Franke Maris MAG11031OW-ONY-CA | Fragranite undermount, single bowl | The largest single bowl in the set | Bowl 31.457 x 17.035 in., depth 9.496 in., cabinet 36 in. | Needs a 36 inch cabinet |
| Franke Ellipse ELG11022MBK | Fragranite undermount, single bowl | A deep bowl on a 27 inch cabinet | 25 x 19.62 in., bowl depth 9.016 in. | Strainer assembly not included |
| Franke Ellipse ELG120ONY-CA | Fragranite undermount, double bowl | Two equal bowls, strainer included | Each bowl 14.331 x 16.89 in., depth 9.016 in. | Each bowl is narrower than the Maris single |
| Franke Peak PKG11020SLG | Fragranite undermount, single bowl | The smallest cabinet in the set | Cabinet 24 in., integrated ledge, bowl depth 7.874 in. | Least deep Fragranite bowl here |
| Franke UCS6805P-1 | Stainless steel undermount, single bowl | An accessible shallow bowl | 18 gauge type 304, bowl 16 x 18 x 5 in. | 5 inch depth limits soaking large pans |
How we selected
This set was built from Franke’s own product pages and one listing page for the UCS6805P-1, and every model had to be a Franke sink with its material, dimensions, bowl depth and installation type printed on the page. Models whose pages gave only a name and a picture were left out, however familiar the name.
The six were then spread across the brand on purpose. The set holds two stainless steel models and four Fragranite models, single bowls and one double bowl, overall widths from 22.06 inches to 33 inches, and stated minimum cabinets from 24 inches to 36 inches. That spread is the useful comparison for a brand keyword: it shows how far one maker’s own range stretches before a buyer needs to look at another maker at all.
Claims stay with the maker throughout. Where a page describes its material as scratch resistant, fade resistant and impact resistant, the article reports that as the maker’s description of the Maris, not as a finding. Where a page is silent, the article says so: the UCS6805P-1 page, for example, prints no minimum cabinet size, and none is estimated for it here.
Sinks for kitchen franke models, one by one
The six profiles below follow the same order of questions: who the sink suits, why it fits a Franke shortlist, the specs its page states, and the limits that page shows. Bowl dimensions and cabinet figures are quoted as printed, including the decimal figures Franke uses on its Fragranite sheets.
Franke Peak PKX11028-S stainless steel undermount sink
The Peak PKX11028-S is the steel flagship of this set: a 16 gauge stainless steel undermount with a Diamond finish, an overall size of 28 3/4 by 17 3/4 inches, and a bowl of 27 3/16 by 16 1/2 inches at 9 5/8 inches deep. Its sheet lists sound pads and a weight of 29 lbs.
The design point is the integrated ledge. The maker’s sheet describes a ledge that lets a cook work directly over the sink, with custom-fit accessories made to sit on it, and it lists two accessories in the box: a drain cover and a strainer assembly. The corners are a tight 5mm radius, and the sheet describes the drain as an invisible drain style, which gives the bowl a flat, plain floor. For a buyer who wants one maker’s best steel specification rather than the thinnest price point in the range, this is the page that states the most.
The limit is documentary rather than physical. Franke’s own sheets for this model family do not all print the same minimum cabinet figure: the sheet behind this profile states 30 inches, while another Franke sheet for the Peak 28 inch model states a larger figure. The practical step is to confirm the cabinet figure on the final listing before the counter is cut, because the bowl itself, at 27 3/16 inches wide, leaves little slack inside a small cabinet.
- Pros: 16 gauge steel, the thickest in this set; integrated ledge for work over the bowl; drain cover and strainer assembly listed as included; 9 5/8 inch bowl depth.
- Cons: single bowl only; minimum cabinet figure differs between Franke documents; ledge accessories beyond the included two are separate purchases.
- Buy if: you want Franke’s ledge workstation idea in stainless steel and your cabinet matches the confirmed figure.
- Skip if: you need two bowls, or your cabinet is under 30 inches and cannot be confirmed against the sheet.
Franke Maris MAG11031OW-ONY-CA Fragranite sink in Onyx
The Maris is the biggest single bowl in this set. Its page describes a 33 by 19.3 inch Fragranite undermount in Onyx with a bowl of 31.457 by 17.035 inches and a depth of 9.496 inches, which the maker rounds to a 9 1/2 inch deep bowl in its own description text.
Two stated features shape how it works. The page lists an accessory rail system that supports optional accessories and turns the sink into a workstation, and it describes a rear offset drain that, in the maker’s wording, maximizes the usable surface of the bowl and creates extra cabinet space beneath the sink. The maker also describes the Fragranite material as scratch resistant, fade resistant and impact resistant. A strainer assembly is included, the page lists cUPC certification, and the minimum worktop thickness is stated as 20 mm.
The costs are space and commitment. The minimum cabinet size is 36 inches, the largest in this set alongside the double Ellipse, and the Onyx finish is a fixed color decision made at order time. The page also states there is no faucet hole, so the faucet mounts in the counter or the wall, which is normal for undermount sinks but has to be planned before the counter is drilled.
- Pros: largest single bowl here at 31.457 inches wide; rear offset drain per the maker; accessory rail; strainer assembly included.
- Cons: 36 inch minimum cabinet; single fixed color on this variant; no faucet hole, so deck or wall faucet planning is required.
- Buy if: you have a 36 inch cabinet and want one wide granite composite bowl with a rail system.
- Skip if: your cabinet is smaller, or you want to split washing and rinsing into two bowls.
Franke Ellipse ELG11022MBK Fragranite sink in Matte Black
The Ellipse ELG11022MBK puts a deep Fragranite bowl on a mid-size cabinet. The page lists an overall size of 25 by 19.62 inches, a bowl of 21.85 by 16.89 inches, a bowl depth of 9.016 inches, and a minimum cabinet size of 27 inches, in a Matte Black finish.
The material description is the clearest in the set. The maker states the sink is made with 80 percent quartz, which it calls the most durable component of granite, bonded with 20 percent acrylic resin. The page lists IAPMO certification, a 3 1/2 inch drain hole, no overflow and no faucet hole. For a 25 inch sink, the 9.016 inch depth is the working asset: it takes tall pots and stacked pans that a shallow compact bowl would not, while the footprint still fits a 27 inch cabinet that rules out the 33 inch models.
The limit is in the box contents. The page states plainly that no strainer assembly is included and lists no waste kit, so the drain fitting is a separate purchase that has to match the 3 1/2 inch drain hole. Buyers comparing this model against the Maris on price alone should add that fitting to the Ellipse side of the ledger before deciding.
- Pros: 9.016 inch bowl depth on a 27 inch cabinet; maker states the 80/20 quartz and resin mix; compact 25 inch width.
- Cons: strainer assembly not included; single bowl; Matte Black is the finish on this variant.
- Buy if: your cabinet is 27 inches and you want depth over width in a granite composite sink.
- Skip if: you want the drain fitting in the box, or you need a double bowl.
Franke Ellipse ELG120ONY-CA double bowl Fragranite sink
The ELG120ONY-CA is the double bowl entry in this set: a 33 by 19.75 inch Fragranite undermount in Onyx with two equal bowls, each 14.331 by 16.89 inches and 9.016 inches deep, on a stated minimum cabinet size of 36 inches. It is the only double bowl among the six models in this guide.
Equal bowls are the point. Each side matches the other in width, front to back size and depth, so washing and rinsing get the same room, and a large pan fits either side the same way. The page uses the same material description as the single Ellipse, 80 percent quartz bonded with 20 percent acrylic resin, lists IAPMO certification, and states that a strainer assembly is included, which the single bowl Ellipse does not offer. Both bowls take a 3 1/2 inch drain hole per the sheet’s single stated figure.
The trade is width per bowl. At 14.331 inches each, neither bowl matches the 31.457 inch clear span of the Maris single bowl, so a wide roasting pan or a large sheet pan will not lie flat in either side. The 36 inch cabinet requirement matches the Maris, so this model does not save cabinet space either; it spends the same cabinet on division instead of span.
- Pros: two equal 9.016 inch deep bowls; strainer assembly included; same stated quartz and resin mix as the single Ellipse.
- Cons: each bowl is 14.331 inches wide; 36 inch minimum cabinet; no faucet hole.
- Buy if: you wash and rinse at the same time and want both bowls the same size.
- Skip if: you regularly soak wide pans flat, where the Maris single bowl serves better.
Franke Peak PKG11020SLG Fragranite sink in Slate Grey
The Peak PKG11020SLG is the compact ledge sink in granite: 22.06 by 18.21 inches in Slate Grey Fragranite, with a bowl of 20.472 by 16.535 inches, a depth of 7.874 inches, and the smallest stated minimum cabinet in this set at 24 inches. It brings the Peak ledge format down to the footprint of a prep sink.
It carries the Peak idea into a small footprint. The page states an accessory ledge on the bowl and describes an integrated ledge that creates a raised workspace so work happens directly over the sink, and it lists Active Twist compatibility for a waste control. The maker also points to clean lines and tight corners as the design character. For a small kitchen, a second sink in an island, or a prep corner, this is the Franke page that combines the ledge system with a 24 inch cabinet.
The limits are depth and box contents. At 7.874 inches, this is the least deep Fragranite bowl in the set, about an inch and a half under the Ellipse bowls, and the page states that no strainer assembly is included. The minimum worktop thickness is stated as 20 mm, which the counter material has to meet for the undermount fitting.
- Pros: fits a 24 inch cabinet, the smallest here; integrated ledge at a compact size; Active Twist compatibility listed.
- Cons: 7.874 inch bowl depth; strainer assembly not included; single small bowl.
- Buy if: you want the ledge workstation format in a small kitchen or as a prep sink.
- Skip if: you need a deep main bowl for a family kitchen.
Franke UCS6805P-1 stainless steel undermount sink
The UCS6805P-1 is the specialist of the set: an 18 gauge type 304 stainless steel undermount with a #4 satin finish, an overall size of 18 1/8 by 20 1/8 inches, and a bowl of 16 by 18 inches at only 5 inches deep, with the waste at the left rear. Its page presents it as an accessible sink.
Its page explains the shallow bowl directly. It describes the sink as wheelchair accessible, meeting ADA and ANSI A117.1 guidelines as printed on the page, with a note to check local codes for compliance. The steel is stated as type 304, CNS 18/10, at 1.2 mm, the sink is undercoated to reduce condensation and resonance in the maker’s wording, and the page lists certification to ASME A112.19.3-2008 and CSA B45.4-08. The box is complete for a small install: waste fitting, cutout template and installation hardware are all listed as included, with a 3 1/2 inch crumb cup strainer and a brass tailpiece.
The limits follow from the brief it serves. A 5 inch bowl will not soak a large roasting pan, and the left rear waste position is fixed, so the plumbing layout has to suit it. The opened page also states no minimum cabinet size, so that figure has to come from the maker’s documents at order time rather than from this profile.
- Pros: accessible 5 inch bowl depth per the page; waste fitting, template and hardware included; certified to ASME and CSA standards as listed.
- Cons: shallow bowl limits soaking; fixed left rear waste; no minimum cabinet size stated on the opened page.
- Buy if: you are fitting an accessible kitchen or a small secondary sink station.
- Skip if: this would be the main family sink for large cookware.
Buying guide
Within one brand, the buying work is less about the badge and more about reading the maker’s own fields in the right order. Cabinet size first, then bowl depth, then included parts: those three fields, all printed on the pages above, decide most of what differs between these six Franke models.
Match the cabinet figure on sinks for kitchen franke picks
The stated minimum cabinets in this set run from 24 inches for the compact Peak granite sink to 36 inches for the Maris and the double Ellipse, with the single Ellipse at 27 inches and the Peak stainless sheet at 30 inches. That figure is a hard gate: an undermount bowl wider than the cabinet interior cannot be fitted or serviced.
Measure the cabinet interior, not the door front, and compare it with the figure on the exact variant page, because Franke prints cabinet figures per variant and, as the Peak stainless sheets show, documents for one model family can differ. Where a page states no cabinet figure, as the UCS6805P-1 page does, treat that as a question to close with the maker before ordering, not as a detail to estimate from the bowl size.
Choose stainless steel or Fragranite by daily work
The two steel models state their build: 16 gauge with a Diamond finish on the Peak, and 18 gauge type 304 steel with a #4 satin finish on the UCS6805P-1. The four Fragranite models state a molded mix, described on the Ellipse pages as 80 percent quartz bonded with 20 percent acrylic resin, in fixed colors such as Onyx, Matte Black and Slate Grey.
The practical difference is what each page lets you plan around. Steel models state a gauge, so thickness can be compared directly. Fragranite models state a color and a material mix, so the decision runs through the counter color and the feel of a molded bowl. Neither line in this set states a faucet hole, so both lines push the faucet onto the counter or the wall.
Read bowl depth as a working dimension
Bowl depth in this set runs from 5 inches on the accessible UCS6805P-1 to 9 5/8 inches on the Peak stainless and 9.496 inches on the Maris. Depth decides what stands upright in the bowl, how much splash stays inside during rinsing, and how far the user reaches down to the bowl floor during a long wash session.
Match depth to the tallest item washed often, not the largest item owned. A stockpot used weekly matters more than a roasting pan used twice a year, which can be washed across the top of the bowl instead. Shallow bowls also pair with accessible design, as the UCS6805P-1 page shows, where the 5 inch depth is the feature rather than a compromise.
Count what the box includes before comparing totals
Included parts differ across this brand more than buyers expect. The Maris and the double Ellipse list a strainer assembly in the box, the Peak stainless sheet lists a drain cover and a strainer assembly, the UCS6805P-1 lists a waste fitting, template and hardware, and the single Ellipse and the compact Peak list no strainer assembly at all.
Price the whole installation, not the sink body alone. A model that excludes the strainer needs one bought to match its 3 1/2 inch drain hole, and ledge models invite accessory purchases that only fit that ledge system. The honest comparison is sink plus the parts its page leaves out, against sink plus nothing further needed.
Plan the faucet around a sink with no faucet hole
Every Fragranite page in this set states no faucet hole, and the steel pages describe undermount bowls without a faucet deck. That is standard for undermount sinks, but it moves two decisions earlier: the faucet style, and where its holes are drilled in the counter behind the bowl.
Leave room in that plan for the faucet reach. A 33 inch bowl like the Maris, at 17.035 inches front to back inside, needs a faucet spout that reaches near the bowl center from behind the sink, and the rear offset drain on that model changes where water lands. Confirm the faucet reach figure on its own page before the counter is drilled, because the counter holes are the one part of the job that cannot be moved later.
FAQ
Most questions about a single-brand shortlist come back to fit and contents: what cabinet each model needs, what the material names mean on the maker’s pages, and what arrives in the box. The answers below use only the figures and wording printed on the six pages behind this guide.
Are sinks for kitchen franke kitchens all undermount models?
All six models in this set are listed as undermount on their pages, from the 22.06 inch Peak granite sink to the 33 inch Maris. That is a property of this selection, which was built from Franke’s current undermount pages, rather than a rule about everything the maker sells in every market and year.
What does Fragranite mean on a Franke page?
Fragranite is the maker’s name for its granite composite material. On the Ellipse pages, Franke describes the mix as 80 percent quartz bonded with 20 percent acrylic resin, and the Maris page uses the same material name while describing it as scratch resistant, fade resistant and impact resistant in the maker’s own wording.
Which Franke sink here fits the smallest cabinet?
The Peak PKG11020SLG, on a stated minimum cabinet size of 24 inches. The next smallest figure in the set is 27 inches for the Ellipse ELG11022MBK, and the two 33 inch models, the Maris and the double Ellipse, both state 36 inches, so cabinet size is the first filter to apply.
Does the Peak stainless sink include a strainer?
Yes, on the sheet behind this profile. The Peak PKX11028-S sheet lists a drain cover and a strainer assembly under included accessories, while the bottom grid, colander and cutting board appear under optional accessories with their own model codes, so those three are separate purchases.
Why is one Franke bowl only 5 inches deep?
The UCS6805P-1 page describes an accessible design: it states the sink is wheelchair accessible and meets ADA and ANSI A117.1 guidelines as printed, with a note to check local codes. The shallow 5 inch bowl, the left rear waste and the included waste fitting all serve that brief rather than a family wash-up brief.
Conclusion
Franke’s own pages draw clear lines: the Peak PKX11028-S for 16 gauge steel and a ledge, the Maris for the widest single bowl, the two Ellipse models for depth in single or double form, the compact Peak granite for a 24 inch cabinet, and the UCS6805P-1 for accessible design. Match the cabinet figure first and the rest follows.