Key takeaways
- Five top-mount kitchen sinks with a rear faucet deck, compared on stated deck holes, hole drilling configurations, cutouts, gauge and mounting hardware figures.
The back of a top-mount sink is its rear ledge: the raised deck behind the bowl that carries the faucet holes. This roundup compares kitchen sinks for backs in that reading, using the deck and hole figures the makers publish: pre-drilled deck holes, hole drilling configurations, mounting hardware and stated cutouts.
Quick verdict
All five picks are top-mount or dual-mount sinks with a back ledge drilled or charted for the faucet. The Delta deck is the thickest stated at 4 mm with 2 pre-drilled holes, the Kraus deck takes a stated 1-3/8 inch hole, and the three Elkay sheets publish hole drilling configurations for their rear decks.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Delta Lorelai 95A932-33S-SS | Drop-in workstation | A thick, pre-drilled deck | 4 mm deck, 2 pre-drilled holes | Deck layout is fixed at 2 holes |
| Elkay Lustertone Classic LR3322 | Drop-in double bowl | Charted hole configurations | 33 x 22 inches, alternate punching | Hole layout set at order or install |
| Kraus Standart PRO KHT300-33 | Dual mount single bowl | A single wide bowl | 33 x 22 inches, 1-3/8 inch deck hole | Dual mount, deck used top-mount only |
| Elkay Lustertone ILR3322L | Top mount with drainboard | A deck plus a drainboard | 33 x 22 inches, left drainboard | Drainboard takes counter width |
| Elkay Lustertone Classic STLR3322R | Drop-in, right deep bowl | One deep bowl, one standard | Right bowl 10 inches deep | Template not included in the box |
How we selected
The keyword names a part of the sink rather than a sink type, so this roundup uses one reading throughout: the back ledge, meaning the rear deck of a top-mount sink where the faucet mounts. Each sink below was selected because its opened page states that deck: pre-drilled holes, a hole diameter, or a published set of hole drilling configurations.
Two other readings were set aside. Sinks with an integrated backsplash panel and sinks marketed on comfort for the user’s back did not produce five models with the feature stated on an opened page, so neither reading could carry a roundup under the rule used here. What remains is the deck reading, and every figure below is a deck, hole, cutout or hardware figure from the maker documents.
Kitchen sinks for backs: the rear deck roundup
The five sinks are all 33 by 22 inch class top-mounts, and they separate on the back ledge. One deck is pre-drilled at the factory, one is charted with alternate punching for specific faucet models, one is drawn with a stated hole diameter, and two carry a drainboard or a deep right bowl behind the same style of rear deck.
Delta Lorelai 33 inch Workstation Drop-In Top Mount Single Bowl – 95A932-33S-SS
Delta describes this Lorelai by its mounting deck: the collection is defined by a gently rounded mounting deck, and the drop-in model carries a heavy-duty 4 mm mounting deck with 2 pre-drilled holes and a beveled edge. That deck is the back ledge of the sink, and at 4 mm stated thickness it is the most substantial deck figure in this roundup.
The sink behind the deck measures 33 by 22 by 9.5 inches overall, with a bowl of 29.88 by 16 by 9 inches and a minimum cabinet of 36 inches. The build is TRU16 gauge stainless steel. Delta lists an accessory hole on the right side of the deck for a soap dispenser or an air gap, and names its own air gap model as a fit in the page answers. The rear-offset drain has an opening of 3.88 inches.
The kit includes an acacia cutting board, a roll-up drying rack, a bottom grid, a drain assembly with cover cap, mounting hardware and a cut-out template. Delta lists NoiseDefend soundproofing with pads covering over 80 percent of the sink, an anti-condensation undercoating, a Lifetime Limited Warranty and cUPC certification. The deck layout is fixed: 2 pre-drilled holes, and Delta advises against drilling additional holes in the deck in its answers.
The same page states the bowl figures behind the deck: a non-porous surface with rounded EZClean corners, drainage grooves that channel water into the drain, and an optimized slope. None of those change the deck, but they complete the stated record for the sink the deck belongs to, and they are the figures a buyer comparing bowls behind identical decks would use.
- Pros: 4 mm deck stated, holes pre-drilled, accessory hole included, full kit in the box
- Cons: 2 hole layout is fixed, 36 inch cabinet, extra holes not advised by the maker
- Buy if: a single-hole or 2-hole faucet set is the plan and you want the deck ready-made
- Skip if: your faucet needs 3 or 4 deck holes, since this deck is drilled for 2
Elkay Lustertone Classic Stainless Steel 33 x 22 x 8-1/8 inch Equal Double Bowl Drop-in Sink – LR3322
The LR3322 sheet presents the back ledge as a configuration: its second page is given to hole drilling configurations, and the sheet lists alternate punching by faucet model and punch required. The deck is not pre-committed to one layout; the punching is chosen for the faucet that will sit on it, which is the flexible answer to the deck question.
The sink is an equal double bowl drop-in at 33 by 22 by 8-1/8 inches, in 18 gauge 304 stainless steel with a Lustrous Satin finish. Each bowl measures 13-1/2 by 16 by 7-3/4 inches, with center drains of 3-1/2 inches. Sound treatment is pads on the sides and bottom. The stated minimum cabinet is 36 inches.
Mounting hardware, Part 64090014, is included for countertops up to 3/4 inch thick, and the cutout is published as 32-3/8 by 21-3/8 inches. The sheet lists ASME A112.19.3 and CSA B45.4 compliance with IAPMO listing, and names optional accessories including bottom grids, cutting boards, a drain and a soap dispenser model for the deck.
The accessory list is itemized on the sheet: bottom grid LKWBG1316SS, cutting boards CB1613, CB1713 and CBS1316, drain LK99, faucets LKGT1041CR, LKGT1041NK and LKGT1041RB, hardware LK364 and LK463, rinsing basket LKWRB1316SS and soap dispenser LKGT1054. The three faucet finishes listed are the models the punching chart is built around.
- Pros: hole layout chosen by punching chart, hardware included, published cutout
- Cons: punching must be settled before install, 18 gauge steel, 36 inch cabinet
- Buy if: your faucet model is known and you want the deck punched to match it
- Skip if: you want holes already drilled with no configuration step
Kraus Standart PRO 33 inch Dual Mount Single Bowl – KHT300-33
The Kraus spec sheet draws the back ledge with a number on it: a deck hole diameter of 1-3/8 inch, also given as 35 mm, on the dimension drawing. The sink is a dual mount single bowl at 33 by 22 inches, with a bowl of 31 by 18 inches and a depth of 10 inches, in 16 gauge stainless steel, so the deck carries a wide, deep basin behind it.
The stated minimum cabinet is 36 inches left to right and 24 inches front to back. The drains are rear center set with 3-1/2 inch openings. Kraus lists NoiseDefend undercoating and sound dampening pads. Included are the strainer ST-1, the cover cap STC-2, the bottom grid KBG-300-33, a cut-out template and mounting hardware for both mount styles.
One fitting limit is printed on the sheet: the maximum countertop thickness for top mount installation is 1-1/2 inches. The sheet lists cUPC certification to ASME A112.19.3 and CSA B45.4 and a Kraus Limited Lifetime Warranty. In its top-mount fitting the deck sits on the counter like the others here; fitted undermount, the deck and its hole leave the counter surface.
The drawing gives one more bowl figure: a corner radius of R 3/8 inch, also printed as 10 mm. A tight radius is what lets the included bottom grid, sized to the 31 by 18 inch bowl, sit flat in the corners, and it is stated on the same sheet as the deck hole, so both fitting figures come from one document.
- Pros: deck hole diameter stated on the drawing, 16 gauge steel, grid and strainer included
- Cons: top mount limited to 1-1/2 inch counters, dual mount hardware for two fittings
- Buy if: a single deep bowl and a standard 35 mm deck hole match your faucet
- Skip if: your counter is thicker than 1-1/2 inches for a top-mount fitting
Elkay Lustertone Stainless Steel 33 x 22 x 7-5/8 inch Single Bowl Top Mount Sink with Drainboard – ILR3322L
The ILR3322L pairs its back ledge with a drainboard: a single bowl top mount at 33 by 22 by 7-5/8 inches, with the drainboard on the left and the faucet deck behind the bowl as usual. The sheet includes hole drilling configurations for that deck, so the faucet layout is charted the same way as on the LR3322.
The bowl measures 16 by 16 by 7-1/2 inches with a center drain of 3-1/2 inches. The build is 18 gauge 304 stainless steel with a Lustertone finish, and sound treatment is pads on the bottom only. The stated minimum cabinet is 36 inches. A similar model with the drainboard on the opposite side is noted on the sheet.
Mounting hardware, Part 64090014, is included for countertops up to 3/4 inch thick, and the cutout for top mount installation is 32-3/8 by 21-3/8 inches. The sheet lists ASME A112.19.3 and CSA B45.4 compliance, IAPMO listing and a limited lifetime warranty document link. The drainboard is the trade: it gives draining space beside the bowl and takes the counter width a second bowl would use.
The sheet’s accessory page names the parts that go with this deck and bowl: cutting boards CB1713 and CBS1316, drain LK99, faucets LKGT1041 and LKGT2041, hardware LK364 and LK463, rinsing baskets LKWRB1316SS and LKWERBSS, the Sinkmate LKSMHSL and soap dispenser LKGT1054. Two faucet models are named, which is the deck’s working shortlist.
- Pros: drainboard beside the bowl, charted deck holes, hardware included
- Cons: single 16 inch bowl, bottom pads only, drainboard side is fixed on this model
- Buy if: draining space on the counter matters more than a second bowl
- Skip if: you need two bowls, or the drainboard must sit on the right
Elkay Lustertone Classic Stainless Steel 33 x 22 x 10-1/8 inch Equal Double Bowl Drop-in Sink with Right Deep Bowl – STLR3322R
The STLR3322R varies the bowl plan behind the same kind of rear deck: an equal double bowl drop-in at 33 by 22 by 10-1/8 inches where the right bowl runs deeper than the left. Its sheet also publishes hole drilling configurations for the back ledge, with the installation profile drawn on page two.
Bowl one measures 13-1/2 by 16 by 7-1/2 inches and bowl two, the right bowl, measures 13-1/2 by 16 by 10 inches. The build is 18 gauge 304 stainless steel with a Lustrous Satin finish, center drains of 3-1/2 inches, and pads on the bottom only. The stated minimum cabinet is 36 inches.
Mounting hardware, Part 64090014, is included for countertops up to 3/4 inch thick. The template is not included in the box; the sheet gives the cutout template number, 1000001189, for download, and publishes the cutout as 32-3/8 by 21-3/8 inches with a 1-1/2 inch corner radius. Compliance listed is ASME A112.19.3 and CSA B45.4 with IAPMO listing.
The optional accessories on page two are sized to the 13-1/2 by 16 inch bowls: a stainless steel bottom grid at 12-1/2 by 15 inches, hardwood cutting boards in three sizes, the LK99 drain with strainer basket, and a rinsing basket at 12-1/2 by 15 by 7 inches. The grid and basket sizes confirm the bowl figures from a second part of the same sheet.
- Pros: one 10 inch deep bowl, charted deck holes, published cutout and template number
- Cons: template not in the box, 18 gauge steel, bottom pads only
- Buy if: a deep right bowl for soaking and a standard left bowl fit your routine
- Skip if: you want the template printed in the box, or equal bowl depths
Buying guide
Buying on the back ledge means buying on holes: how many, what diameter, on what centers, and in a deck of what build. The checks below follow the figures the makers actually publish for these five models, from the hole count down to the counter thickness the hardware and the deck are stated to accept.
Count the holes the kitchen needs
A deck has to carry the faucet and whatever stands with it: a separate sprayer, a soap dispenser, an air gap or a filter tap. The Delta deck is drilled for 2 holes and adds an accessory hole on the right side, per the maker page. The Elkay sheets chart several drilling configurations, and the LR3322 adds alternate punching tied to faucet models.
The count is a faucet decision made before the sink decision. A single-hole faucet with a deck plate, a 2-hole set and a 3-hole set each land on a different deck answer, and drilling a finished deck is the step Delta advises against in its answers for the Lorelai.
Measuring the back ledge on kitchen sinks for backs
The stated figures for a ledge are the hole diameter and the hole centers. Kraus prints a 1-3/8 inch, 35 mm, hole diameter on its drawing, which matches the standard faucet tailpiece class. The Lustertone sheets here chart configurations without a printed center figure in the text.
Deck thickness is the other ledge figure, and only Delta states one: 4 mm for the Lorelai mounting deck. Where a maker does not state deck thickness, the honest position is that the ledge build is unmeasured in the document, and the choice rests on the hole figures that are printed.
Pre-drilled, punched or charted
The three deck systems here work differently. A pre-drilled deck, the Delta, arrives ready and fixed. A punched deck, the Elkay alternate punching route, is opened for the faucet model chosen. A charted deck, the Elkay hole drilling configurations, sets out the layouts the sink accepts so the drilling follows the chart at fitting time.
Each system moves the risk to a different point. Pre-drilled risks a mismatch with the faucet set. Punched and charted decks risk a configuration settled late. The template and cutout figures matter in all three, since the deck only sits flat when the cutout under it matches the published size.
What stands behind the bowl
The back ledge is where the counter run ends, so the models differ in what the deck serves. The Delta deck serves a workstation, with a cutting board and roll-up rack working over the bowl. The ILR3322L gives its width to a drainboard. The STLR3322R puts a 10 inch deep bowl on the right. The deck choice and the bowl choice are the same purchase.
Cabinet size is stated as 36 inches for every model here, so the separation is not cabinet width. It is the layout behind and beside the faucet: accessories on a ledge, a drainboard, or a deep second bowl.
Counter thickness at the deck
Two limits are printed. Kraus caps top mount installation at a maximum countertop thickness of 1-1/2 inches for the KHT300-33. Elkay includes hardware rated for countertops up to 3/4 inch thick with the Lustertone models. The Delta deck sits on the counter with included mounting hardware and a template, with no thickness cap stated on the page.
A thick wood or stone counter can pass the Kraus cap while a thin panel suits the Elkay hardware rating. The figure to match is the one on the sheet for the model chosen, not a general rule about top-mount sinks.
FAQ
The questions below are the ones this reading of the keyword raises: what the back of a sink is, how its holes are specified, and how the deck systems differ. The answers use the figures on the pages opened for the five models above, and say where a maker does not print the figure.
What counts as the back on kitchen sinks for backs?
In this roundup, the back is the rear ledge of a top-mount sink: the deck behind the bowl that carries the faucet. That is the reading used throughout, because it is the sink feature that makers specify in print, with hole counts, hole diameters and drilling configurations.
How many faucet holes does a rear deck need?
It needs the count the faucet set and its accessories add up to. The Delta deck states 2 pre-drilled holes plus an accessory hole for a dispenser or air gap. The Elkay sheets chart several configurations, and the LR3322 sheet ties alternate punching to faucet models. The Kraus sheet states a hole diameter, 1-3/8 inches, rather than a count.
Can extra holes be drilled in a sink deck?
Delta’s answer for the Lorelai is no: its page answers advise against drilling holes in the stainless steel deck, because drilling can damage the sink and compromise its integrity. The Elkay route is different: alternate punching and drilling configurations exist so the layout is set by the chart, not by freehand drilling after delivery.
Is a drainboard model still a rear deck sink?
Yes. The ILR3322L carries its faucet on the rear deck behind the bowl, and its sheet publishes hole drilling configurations for that deck. The drainboard changes what sits beside the bowl, on the left in this model, with a similar model listed with the drainboard on the opposite side. The deck system is unchanged.
What if the counter is thicker than the stated limit?
Then the model is outside its fitting range. Kraus states a maximum countertop thickness of 1-1/2 inches for top mount installation of the KHT300-33, and the Elkay hardware is rated for countertops up to 3/4 inch thick. A thicker counter calls for the maker’s accessory hardware, or a different model; the stated limit is the figure to respect.
Does deck thickness matter?
Only one page states it: Delta gives the Lorelai deck as 4 mm thick. The Elkay and Kraus sheets state hole configurations and a hole diameter, but no deck thickness, so no thickness comparison can be drawn for them. A stated deck thickness is a build figure for the ledge that carries the faucet weight, and its absence is a gap in that sheet.
Conclusion
On the rear deck reading, the Delta 95A932-33S-SS is the ready-made pick: a 4 mm deck, 2 pre-drilled holes and an accessory hole, with the kit in the box. The Elkay LR3322 is the flexible pick, with punching charted by faucet model. The Kraus KHT300-33 states its deck hole diameter on the drawing itself.