Updated Nov 15, 2026· 14 min read

Key takeaways

  • Compare the best item for kitchen sinks read as a bottom grid or sink rack, by dimensions, sink fit, feet and material, from maker spec sheets and listings.

The keyword names no product, just an “item,” so this guide takes the clearest single reading: the removable bottom grid, also sold as a sink rack, that sits in the bowl of a kitchen sink. This guide compares that item for kitchen sinks by dimensions, named sink fit, feet and material, from maker pages.

Quick verdict

A bottom grid only works when it matches the bowl it drops into, so fit leads this list. The Kraus KBG-NST1-30 is the measured pick for its named sink, at 26 1/4 x 14 1/4 x 7/8 inches for the KHU100-30/18, and the Sterling 11867 is the long single-bowl rack at 26-7/8 x 13-3/8 inches for Sterling model 11600.

The four Kohler racks split by sink family: the Stages K-6234 at 19 x 15-1/16 inches for the K-3760 Stages sink, the Poise K-3143 at 17-3/16 x 13-3/16 inches for the K-3160 Poise sink, the reversible Deerfield rack for the right bowl of the K-5873, and the Riverby left-hand rack for Riverby sinks, listed at 18.56 x 14.13 inches. Every rack here is stainless steel with protective feet per its maker or listing, and every dimension below comes from the opened page for that rack.

Product Dimensions listed Named sink fit Feet per page Material
Kraus KBG-NST1-30 Bottom Grid 26 1/4 x 14 1/4 x 7/8 inches KHU100-30/18 Rubber feet Stainless steel
KOHLER Stages Sink Rack K-6234 19 x 15-1/16 inches K-3760 Stages Rubber feet Stainless steel
KOHLER Poise Sink Rack K-3143 17-3/16 x 13-3/16 x 1 inch K-3160 Poise Rubber feet Stainless steel
Kohler Deerfield Sink Rack, Right 12.88 x 15.38 x 0.63 inches K-5873 Deerfield, right bowl Rubber feet Stainless steel
Sterling Sink Rack 11867 26-7/8 x 13-3/8 x 1-3/16 inches Sterling model 11600 Nonabrasive plastic feet Stainless steel
Kohler Riverby Left-hand Sink Rack 14.13 x 18.56 inches Riverby sinks, left-hand Rubber feet Stainless steel

How we selected

Each item here had to be one product type only, a bottom grid or sink rack for a kitchen sink, with a maker spec sheet or product listing that could be opened and that states dimensions and a named sink or sink family it fits. Other readings of the keyword were not mixed in.

That single-type rule is the whole method for an unclear keyword: strainers, cutting boards, dish racks and dispensers are all items for a kitchen sink in ordinary speech, but blending them would compare unlike products. The six racks that remain are alike in form, stainless steel grids on protective feet, and different in the one way that matters, the bowl each is shaped for. Where a page gives dimensions in fractions, they are quoted as printed; where a listing gives decimals, those are quoted as printed too.

The reading also sets what this guide does not do. It does not rank a grid against a strainer or a cutting board, because those products answer different questions, and it does not treat the word item as a license to gather anything sold near a sink. A reader who meant a different accessory can still use the same approach: settle on the one product type the phrase most plausibly names, then compare products of that type on their stated dimensions, fits and materials, rather than blending two types into one list and calling the blend an answer.

Item for kitchen sinks, rack by rack

The six racks below are ordered by bowl size, from the long single-bowl grids to the half-bowl racks for double sinks. Each entry gives the exact product name, the sink it is made for, the dimensions and feet its page states, the limits on the same page, and a plain buy-if and skip-if line drawn from those stated fits.

Kraus KBG-NST1-30 Stainless Steel Kitchen Sink Bottom Grid

The Kraus grid is the aftermarket-style entry: a bottom grid sized for one named sink, the KHU100-30/18, with overall dimensions of 26 1/4 x 14 1/4 x 7/8 inches on the maker’s specification sheet, including a 4 1/2 inch drain opening as drawn on that sheet.

The sheet describes commercial grade stainless steel construction, rubber feet that provide additional protection, and the maker’s own line that the grid protects the bottom of the sink from daily wear and tear, reported here as maker wording. The warranty line on the sheet is a Kraus One Year Limited Warranty. The fit discipline is the point: the sheet names one sink model, so the grid is a measured match for that bowl and a guess for any other. No second sink family is listed, and no corner radius is stated in the fetched text beyond the drawing marks, so a buyer with a different Kraus sink should compare the sheet drawing against the bowl before ordering.

  • Pros: exact dimensions and drain opening on the maker sheet; rubber feet; one named sink fit; stainless construction
  • Cons: fits the one named model per sheet; corner fit must be read from the drawing; one year warranty is the shortest stated here

Buy if your sink is the KHU100-30/18 or measures out the same as the sheet drawing. Skip if your bowl differs, since the sheet names no other fit.

KOHLER Stages Sink Rack K-6234, Stainless Steel

The Stages rack is the large-bowl Kohler entry, a stainless steel sink rack at 19 x 15-1/16 inches made for the K-3760 Stages kitchen sink, the 33 inch undermount single-bowl model named on the maker’s own spec sheet for this rack and its matching sink.

The sheet states that the rack fits the bottom of that sink and is included with it, which makes this entry the replacement or second-rack purchase for Stages owners rather than a first accessory. The maker’s wording says the rack helps protect the sink surface from daily wear, with rubber feet providing added protection, and the material line reads durable stainless steel construction. The finish code is ST Stainless Steel and the warranty line is the KOHLER One-Year Limited Warranty. The sheet also lists the rack for dishwasher cleaning in the maker’s own wording. No weight is stated on the sheet, so none is given here.

  • Pros: made for the 33 inch Stages bowl; included-with-sink pedigree; rubber feet; maker sheet dimensions in fractions and millimeters
  • Cons: one sink model only; one year warranty; no weight stated for handling comparisons

Buy if you own the K-3760 Stages sink and want its own rack or a spare. Skip if your sink is any other model, since the sheet names no second fit.

KOHLER Poise Sink Rack K-3143, Stainless Steel

The Poise rack is the mid-size Kohler entry, at 17-3/16 x 13-3/16 inches with a height of 1 inch (25 mm) per the drawing on its spec sheet, made to fit in the bowl of the K-3160 Poise kitchen sink, the single sink model its maker names for this rack.

Its sheet follows the same pattern as the Stages sheet: the maker wording says the rack helps protect the sink surface from daily wear, rubber feet provide added protection, the material is durable stainless steel construction, the finish is ST Stainless Steel, and the warranty is the KOHLER One-Year Limited Warranty. The sheet also lists the rack for dishwasher cleaning in the maker’s wording. The 1 inch height is the useful comparison figure here, since it sets how much bowl depth the rack takes and how tall items sit above the bowl floor while they drain. No drain opening position is described in the fetched text, so alignment with the Poise drain is read from the fit naming itself. Set beside the Stages rack, the Poise is the same idea at a smaller scale: a maker-drawn grid for one bowl, with the comparison between the two resting on dimensions and height rather than on any difference in materials or feet.

  • Pros: stated 1 inch height; named Poise fit; rubber feet; stainless construction; maker sheet gives metric equivalents
  • Cons: single sink model fit; one year warranty; drain opening not described in text

Buy if your sink is the K-3160 Poise and you want the rack drawn for its bowl. Skip if you need a universal rack, since this sheet names one model only.

Kohler Deerfield Sink Rack, Right

The Deerfield rack is the double-bowl entry, sized for one side of a double-equal sink. Its listing gives a length of 12.88 inches, a width of 15.38 inches and a height of 0.63 inches, in stainless steel, and names the right bowl of the K-5873 Deerfield kitchen sink as its fit.

One feature separates it from the other five: the listing describes a reversible design that allows the rack to fit in either bowl, even though the product is sold as the right-hand rack. The listing wording says the stainless steel wire rack protects dishes and the enamel surface of the basin from scratches, reported here as listing wording, and the feature list adds rubber feet and dishwasher cleaning in the listing’s own wording. The collection is Deerfield and the type is listed as Kitchen Accessories. The listing does not state a K-number for the rack itself in the fetched text, so the rack is identified here by its listing name.

  • Pros: reversible between bowls per listing; enamel-basin wording suits cast iron sinks; rubber feet; compact half-bowl size
  • Cons: fits one named double sink; rack model number not stated on the listing; 0.63 inch height is the lowest profile here

Buy if your double-equal sink is the K-5873 Deerfield and you want one rack that can move between bowls. Skip if your sink is a single bowl, since this rack is drawn for half of one.

Sterling Sink Rack 11867

The Sterling rack is the long utility entry, at 26-7/8 inches (683 mm) x 13-3/8 inches (340 mm) with a height of 1-3/16 inches (30 mm) on the maker’s spec sheet, made for use with Sterling model 11600, and built in stainless steel per the sheet’s material line.

Two feature lines set it apart. The sheet states that the rack rests on nonabrasive plastic feet, which the maker wording says will not harm the sink finish, the only plastic feet in this guide against five sets of rubber feet. The sheet also states a drain hole opening that allows the drain to be used without removing the rack, a practical line none of the other sheets prints. The maker’s wording says the rack protects the bottom of the basin from objects that would damage the surface. Warranty detail is referred to the maker’s site on the sheet rather than stated as a term, so no term is quoted here.

The Sterling sheet is also the oldest document in this set, dated 2020 on its face, which cuts both ways for a buyer. The dimensions and the drain opening line are stated as plainly as on any newer sheet, and the model 11600 fit is unambiguous. At the same time, a sheet of that age is a reason to confirm current availability of the rack itself before treating it as a stocked item, since the sheet proves the product’s design and fit rather than its present listing status on a shelf.

  • Pros: drain opening usable in place per sheet; plastic nonabrasive feet; longest rack here; metric dimensions stated
  • Cons: one named Sterling model; warranty term not stated on the sheet; tallest profile at 1-3/16 inches

Buy if your sink is Sterling model 11600 and you want the drain usable with the rack in place. Skip if your sink is another brand, since the sheet names the one model.

Kohler Riverby Left-hand Sink Rack

The Riverby rack is the handed entry: a left-hand rack for Riverby kitchen sinks, listed at a width of 18.56 inches and a length of 14.13 inches in stainless steel, designed to fit into the left-hand bottom of select Riverby sinks per its listing page.

The listing states that the rack is included with K-5871 Riverby sinks, that it is recommended for use with the K-6255 Riverby right-hand rack, and that rubber feet provide added protection. Its wording says the rack helps protect the sink’s enamel surface, reported here as listing wording, and the listing also names dishwasher cleaning in its own wording. The pairing note is the buying signal: a Riverby owner with a double sink is looking at two handed racks, left and right, rather than one reversible piece like the Deerfield. No height is stated on the listing, so none is given here.

  • Pros: handed fit for Riverby bowls; pairs with the named right-hand rack; included with K-5871 sinks per listing; rubber feet
  • Cons: left-hand only; height not stated on the listing; full coverage needs the second rack as well

Buy if your Riverby sink needs its left-hand rack, alone or as half of the named pair. Skip if you want one reversible rack for both bowls, which is the Deerfield pattern instead.

Buying guide for an item for kitchen sinks

Four checks decide a bottom grid purchase: the named fit against your sink model, the dimensions against your bowl, the feet material, and whether the drain stays usable with the rack in place. Each check below uses only what the opened pages state, so the same checks work on any other rack page you open.

Start with the named sink fit

Every rack here is made for a named sink or sink family: the KHU100-30/18, the K-3760 Stages, the K-3160 Poise, the K-5873 Deerfield, Sterling model 11600 and the Riverby line. A rack bought by model name either matches its bowl drawing or it does not, and the pages give no universal fit claim to fall back on.

If your sink is one of the named models, the choice is already made and the only question is which bowl or hand. If it is not, the dimension check below becomes the deciding one, and the corner shape of your bowl matters as much as its length, since a grid that bridges a corner will rock instead of resting on its feet.

Measure the bowl, not the sink

The dimensions on these pages are bowl dimensions: 26 1/4 x 14 1/4 inches on the Kraus sheet, 19 x 15-1/16 inches on the Stages sheet, down to 12.88 x 15.38 inches for the half-bowl Deerfield. The outside size of the sink, the figure on a cabinet plan, is larger than every one of these and is the wrong number to shop with.

Measure the flat floor of the bowl, length and width, and compare both figures with a small margin: a grid should sit inside the floor, not climb the bowl walls. Height matters too, from 0.63 inches on the Deerfield listing to 1-3/16 inches on the Sterling sheet, since the rack raises everything placed on it by that amount.

Feet, rubber or plastic

Feet are the contact points between a steel grid and a finished basin, and the pages split two ways. Five racks list rubber feet, with the maker wording that they provide added protection. The Sterling sheet lists nonabrasive plastic feet, with maker wording that they will not harm the sink finish.

Neither page set ranks the two against each other, so the choice rests on the basin: an enamel basin, named on the Deerfield and Riverby listings, is the surface where the feet wording matters most, and both listings answer it with rubber feet and protective wording. Check the feet line on any rack page before the dimension line, because a missing feet note is a gap in the listing.

Drain access and handed racks

A rack that covers the drain changes how the sink is used, and only two pages address the point directly. The Sterling sheet states a drain hole opening that allows the drain to be used without removing the rack, and the Kraus sheet draws a 4 1/2 inch drain opening. The Kohler sheets are silent on the point in text.

Double sinks add a second question. The Deerfield rack is reversible between bowls per its listing, while the Riverby pattern is two handed racks, left and right, sold as a named pair. A double-bowl owner should decide which pattern the sink maker drew for that model before buying either one.

FAQ

Short answers to the questions a bottom grid purchase raises most often, each tied to a dimension, a fit line or a feature line on one of the opened pages above. Where a page does not answer, the answer says so instead of borrowing a figure from a different rack.

What does a sink bottom grid do

Per the maker wording on these pages, the grid sits in the bowl and protects the bottom of the sink from daily wear and tear, in the Kraus sheet’s phrasing, or helps protect the sink surface from daily wear, in the Kohler sheets’ phrasing. The Deerfield listing adds dishes and the basin surface among what its rack protects.

Will one of these racks fit any sink

No page here claims a universal fit. Each rack names its sink: the KHU100-30/18 for the Kraus grid, the K-3760 and K-3160 for the two Kohler sheet racks, the K-5873 for the Deerfield, Sterling model 11600 for the Sterling rack, and the Riverby line for the Riverby rack.

Which rack keeps the drain usable in place

The Sterling 11867 sheet states the point directly: its rack features a drain hole opening allowing the drain to be used without removing the rack. The Kraus sheet draws a 4 1/2 inch drain opening. The Kohler pages here do not print an equivalent line in their fetched text.

What are the racks made of

All six pages name stainless steel: commercial grade stainless steel construction on the Kraus sheet, durable stainless steel construction on the Kohler sheets, stainless steel as the material line on the Sterling sheet, and stainless steel in the Deerfield and Riverby listings. The difference between them is feet and fit, not body material.

Can these racks go in the dishwasher

Four of the Kohler-family pages say so in their own wording: the Stages and Poise sheets and the Deerfield and Riverby listings each list dishwasher cleaning for their rack. The Kraus and Sterling sheets do not print a dishwasher line in their fetched text, so no claim is made for those two here.

Conclusion

For an unclear keyword, the honest answer is one product read well: a bottom grid that matches its bowl. Kraus for the KHU100-30/18, the Stages and Poise racks for their Kohler bowls, the reversible Deerfield for a double sink, Sterling for model 11600 with its open drain, and the Riverby left-hand rack for its named pair.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.