Updated Nov 15, 2026· 13 min read

Key takeaways

  • Compare the best stainless sinks for kitchen 32 inch projects: stated overall dimensions, cabinet minimums, gauges, bowl depths and included parts per sink.

The phrase stainless sinks for kitchen 32 describes a size class, not a single model: every sink in this guide states a 32 inch class width on its page, and five of the six state 32 inches while one states 32-1/4 inches. All six state a 36 inch minimum cabinet, so the cabinet check is uniform even though bowls, depths and included parts differ.

A 32 inch sink is a planning decision before it is a style decision. The overall width decides the cut-out, the stated minimum cabinet decides whether the sink drops into the base unit you already own, and the bowl dimensions decide what fits inside. This guide therefore reads the dimension lines as the product: each model below was included only because its opened page states a 32 inch class overall size or a stated minimum cabinet size, and every figure in the article is copied from that page rather than inferred from a model name or a bowl measurement.

How the Stainless Sinks for Kitchen 32 Class Is Defined

The class is defined by two stated numbers working together: an overall width in the 32 inch range and a minimum cabinet size printed by the maker. Five models here state an overall width of exactly 32 inches, and the sixth states 32-1/4 inches, which places it in the same cabinet class because its sheet also states a 36 inch minimum cabinet.

Front-to-back depth varies more than width does: most state 19 inches, while the Elkay kit states 18-1/4 inches, a difference that matters at the countertop even though the width class matches. Bowl size is not a substitute for overall size. A sink can carry a 30 inch bowl inside a 32 inch body, as four of these models do, but the cut-out follows the overall figure and the flange, not the bowl. That is why this guide never converts a bowl measurement into a fit claim: where a page states only a bowl size, the model was left out. The cabinet figure deserves the same discipline. Every model here states a 36 inch minimum cabinet, and two Kraus sheets state it in two directions, 36 inches left to right and 24 inches front to back, which is the more complete way to check a real base cabinet.

Depth is the third stated number worth comparing before style. Bowl depths in this set run from 8-1/2 inches on the pressed double bowl to 10 inches on four models, with the Delta workstation at 9 inches of bowl depth inside a 9-1/2 inch overall depth. A deeper bowl holds taller stockpots under the faucet, while a shallower double bowl keeps the divider low. None of these figures is better in the abstract; each is a stated trade-off the maker prints, and the right reading is against your own pots, tray sizes and cabinet interior height.

Six Stainless Sinks for Kitchen 32 With Stated Dimensions

The six models split into three workstation single bowls, one plain handmade single bowl, one pressed double bowl with a low divider and one 30/70 offset double bowl kit. All six are undermount, all six state a 36 inch minimum cabinet, and five state a 3-1/2 inch drain opening, the Delta being the exception at a stated 3.88 inches.

Five state 16 gauge steel and one states 18 gauge. The product sections below follow the order of the checks a buyer makes: dimensions first, then bowl layout, then what the box actually includes, because included parts differ sharply across this set. Every model is an undermount, so the countertop material and the mounting hardware matter as much as the bowl, and both are stated on the pages collected here.

Kraus Kore Workstation KWU110-32

The Kraus Kore Workstation KWU110-32 states overall dimensions of 32 by 19 inches, a bowl of 30 by 16 inches and a bowl depth of 10 inches, in 16 gauge steel as a single bowl undermount workstation. Its sheet states a minimum cabinet size of 36 inches left to right and 24 inches front to back, a rear off-set drain and a 3-1/2 inch drain opening.

The built-in ledge carries the included accessories, and the sheet lists NoiseDefend soundproofing with extra-thick pads and protective undercoating. The included list is the fullest of the three Kraus models here: a Strainer ST-1, a Cover Cap STC-2, a Bottom Grid KBG-UN1-32, a Rolling Mat KRM-11BL and a KCB-WS103BB cutting board, plus a cut-out template and mounting hardware. The sheet states cUPC certification to ASME A112.19.3 and CSA B45.4. For a 32 inch brief that wants the workstation format with the accessories settled in one box, this is the sheet that answers the most questions on a single page.

Kraus Standart PRO KHU100-32/18

The Kraus Standart PRO KHU100-32/18 states the same 32 by 19 inch footprint with a larger bowl, 30 by 17 inches, and 10 inch depth, but it is a handmade sink in 18 gauge steel rather than 16. It states the cabinet pair, 36 inches left to right and 24 inches front to back, a rear center-set drain and a 3-1/2 inch opening.

NoiseDefend soundproofing appears here as well, with pads and undercoating described on the sheet in the same terms as the workstation model. The difference is the box. This sheet lists only cut-out templates as included, three of them, and marks the mounting hardware and the strainers, including the BST-1, ST-1 and ST-4, as optional parts sold separately. A buyer comparing the two Kraus single bowls is therefore comparing more than gauge: the handmade 18 gauge shell arrives as a sink and templates, while the 16 gauge workstation arrives as a fitted kit. Both state cUPC certification on their sheets.

Kraus Premier KBU32 Double Bowl

The Kraus Premier KBU32 is the pressed double bowl, stating overall dimensions of 32 by 19 inches with two bowls of 14-1/2 by 17 inches each and a depth of 8-1/2 inches, in 16 gauge steel. A low center divider separates the bowls, and the sheet states a minimum cabinet size of 36 inches with center-set drains and 3-1/2 inch openings.

The shallower depth is the honest trade of the format: two work zones in the same 32 inch width, each holding less depth than the single bowls above. Its included list is complete for a double bowl: two Strainer ST-1 units and two Bottom Grid KBG-32 units, one set per bowl, plus a cut-out template and mounting hardware. NoiseDefend soundproofing is stated, and the sheet carries the same cUPC line as the other Kraus models. One caution belongs in any comparison: another published version of this model’s sheet states slightly different overall figures, so the dimensions used here are the ones on the sheet opened for this guide, and a buyer should confirm the current sheet before fabrication.

Ruvati RVH8300 Roma Workstation

The Ruvati RVH8300 states exterior dimensions of 32 by 19 inches, an interior bowl of 30-1/2 by 16 inches and a bowl depth of 10 inches. Its page states a minimum base cabinet of 36 inches, a 3.5 inch drain opening and 16 gauge construction in T-304 grade stainless steel with an 18/10 chromium and nickel content as printed.

The bowl is the widest stated in this set by half an inch, the inside corners are sharp, zero radius, rather than rounded, and ledges on the front and back form the track for the maker’s LedgeFit accessories. The included list is long: the sink, a stainless steel colander, a solid sapele wood cutting board, a foldable dish drying rack, a stainless steel bottom rinse grid, a basket strainer drain assembly, a decorative drain cover, a cut-out template and mounting brackets. The page states a weight of 48 pounds, a soundguard coating with thick rubber padding, and cUPC certification tested by IAPMO. The commercial brushed finish is described by the maker as hiding scratches, a claim the page makes about appearance rather than a measured property.

Delta Lorelai 95B932-32S-SS Workstation

The Delta Lorelai 95B932-32S-SS states outer dimensions of 32 by 19 by 9-1/2 inches, bowl dimensions of 30 by 16 by 9 inches and a minimum cabinet size of 36 inches. It is a single bowl undermount in TRU16 gauge steel, which the page identifies as 16 gauge, with a rear-offset drain, a SatinSheen finish and a drain opening of 3.88 inches.

The maker’s answers on the page add the two-direction form of the cabinet figure, 36 inches left to right and 24 inches front to back, and the 3.88 inch opening is the one figure in this set that departs from the 3-1/2 inch pattern. The kit includes an acacia cutting board with a mobile device holder, stated at 12 by 16.75 by 0.75 inches, a roll-up dish drying rack with a removable utensil holder that the page rates to hold up to 85 pounds and to 400 degrees Fahrenheit, a silicone drying mat, a stainless steel bottom grid and a stainless steel drain assembly with a removable cover, plus hardware and a cut-out template. NoiseDefend soundproofing and EZClean corners are stated, along with cUPC certification and a Lifetime Limited Warranty; the page also notes the sink can be rotated to move the drain to the left, and the maker’s answers state the model is currently made in China.

Elkay Crosstown EFRU321910DBG 30/70 Kit

The Elkay Crosstown EFRU321910DBG is the one model that states 32-1/4 inches: its sheet gives sink dimensions of 32-1/4 by 18-1/4 by 10 inches for a 30/70 double bowl kit in 16 gauge 304 stainless steel with a Polished Satin finish. The bowls state 7-1/2 by 15-3/4 by 6 inches and 21 by 15-3/4 by 10 inches, with center drain placement.

The sheet states a 3-1/2 inch drain size, a minimum cabinet size of 36 inches and Sound Guard sound deadening. Because it is sold as a kit, the included list is explicit: the EFRU321910 sink, one LKFBG2115SS bottom grid, one LK99 drain described as a deluxe 3-1/2 inch drain with a Type 304 stainless steel body, strainer basket, rubber seal and tailpiece, mounting hardware part 54300008 and a template, number 1000001305, which the sheet notes is also available for download. The sheet states a reversible design, so the small bowl can sit on the left or the right, and lists compliance with ASME A112.19.3 and CSA B45.4. Its narrower 18-1/4 inch front-to-back figure is the dimension to check against your counter.

Comparing Stainless Sinks for Kitchen 32 by Bowl Layout

Bowl layout is where the 32 inch class divides into genuinely different tools. Four models give one uninterrupted bowl of about 30 inches, which takes sheet pans and roasting trays flat; two models divide the width, one into equal halves of 14-1/2 inches and one into a 21 inch main bowl beside a 7-1/2 inch secondary bowl.

Model Overall (in) Bowl(s) (in) Depth (in) Gauge Min. cabinet (in)
Kraus Kore KWU110-32 32 x 19 30 x 16 10 16 36
Kraus KHU100-32/18 32 x 19 30 x 17 10 18 36
Kraus Premier KBU32 32 x 19 14-1/2 x 17 each 8-1/2 16 36
Ruvati RVH8300 32 x 19 30-1/2 x 16 10 16 36
Delta 95B932-32S-SS 32 x 19 30 x 16 9 16 36
Elkay EFRU321910DBG 32-1/4 x 18-1/4 21 x 15-3/4 and 7-1/2 x 15-3/4 10 and 6 16 36

The table collects the stated figures so the layouts can be compared without returning to six separate pages, and the two sections after it read the layouts against the work each one supports. Depths in the table are bowl depths as stated; the Delta figure is its bowl depth of 9 inches rather than its 9-1/2 inch overall depth, and the Elkay row carries both of its bowl depths because the two bowls differ.

Single Bowls at 32 Inches

The four single bowls state interior widths of 30 or 30-1/2 inches, which is the working figure for trays and wide pans. Among them the differences are in the second bowl dimension and the corners: the handmade Kraus states the deepest front-to-back bowl at 17 inches, and the Ruvati states sharp zero radius corners with the widest bowl.

The two workstation models from Kraus and Delta state rounded or ledged interiors built around sliding accessories, and depth splits the group again: 10 inches for the Kraus pair and the Ruvati, 9 inches for the Delta. Accessory ledges are the other single bowl divider. The Kore and the Delta carry built-in ledges with boards and racks in the box, the Ruvati carries ledges front and back with its own board, colander and rack included, and the handmade Kraus carries no ledge at all. A buyer who preps over the sink uses the ledge daily; a buyer who wants an open bowl for soaking finds the ledge is simply rim geometry. The sheets state the parts either way, so the choice can be made from the included lists rather than from photographs.

Double Bowls and the Low Divider

The two double bowls divide the width in opposite ways. The Kraus KBU32 splits it evenly, two 14-1/2 by 17 inch bowls at 8-1/2 inches deep with a low center divider. The Elkay kit splits it unevenly, a 21 inch bowl at 10 inches and a 7-1/2 inch bowl at 6 inches deep, and the sheet states the sink is reversible.

The even split keeps two equal stations and lets long items rest across the lowered divider line, as the maker describes the format, while the small Elkay bowl is the rinsing and straining station beside the main bowl. Drain placement follows the layout: center-set drains on both double bowls, against rear off-set or rear center-set drains on the single bowls. A disposal under one bowl of a double bowl is a stated-compatibility question; the Ruvati page addresses disposal fit for its 3.5 inch opening directly, while the double bowl sheets state opening size and drain hardware without a disposal statement. Read the drain lines of the specific model before assuming the under-sink machinery carries over from the sink it replaces.

Cabinet, Cut-Out and Drain Checks

Every model in this guide states a 36 inch minimum cabinet, which makes the cabinet check simple: the figure is a minimum for the sink, and two makers state it in two directions. The cut-out follows the template each maker includes or numbers, and the drain opening decides which strainer or disposal flange the installation needs.

The 36 Inch Cabinet Rule

A 32 inch sink in a 36 inch cabinet leaves roughly two inches of cabinet structure on each side. The two-direction statements are the most useful form of the figure: the Kraus Kore and Standart PRO sheets state 36 inches left to right and 24 inches front to back, and Delta’s answers state the same pair for the Lorelai.

All six makers land on the same minimum, which is why the class is consistent. Front-to-back deserves its own measurement because the sinks differ there: five state 19 inches overall while the Elkay states 18-1/4 inches, and the faucet position behind the sink comes out of the same counter depth. Measure the cabinet interior, not the door front, and compare it with the stated minimums before ordering; a cabinet that meets the width figure can still crowd the depth figure once plumbing and a disposal share the space. The stated numbers are minimums, not recommendations for comfort.

Drain Openings and Included Hardware

Five of the six models state a 3-1/2 inch drain opening, the standard that the Ruvati page notes will fit a standard garbage disposal unit. The Delta table states 3.88 inches for its drain opening and includes a drain assembly, so the reading is to use the included assembly and confirm disposal fit against the maker’s answer on the page.

That answer states that any garbage disposal can be installed with the maker’s stainless steel sinks, so where two stated figures sit in tension, the included hardware settles the installation. Included hardware is the quiet difference in this class. The Kore, KBU32, Delta and Elkay arrive with strainers or drain assemblies and mounting hardware in the box, the Ruvati adds a decorative drain cover to the same pattern, and the handmade Kraus arrives with templates only, its strainers and hardware listed as optional. None of that is visible in the headline dimensions, and all of it is stated on the sheets, which is why the included list belongs in the first comparison rather than in the order confirmation.

Gauge, Finish and Sound Treatment

Five models state 16 gauge steel and one, the handmade Kraus, states 18 gauge. Finishes are stated just as plainly, from the Elkay’s Polished Satin to the Delta’s SatinSheen and the Ruvati’s commercial brushed finish, each described by its maker in appearance terms.

The sheets present the gauge numbers without a shared ranking, so the useful reading is construction: the 18 gauge model is the handmade one, the 16 gauge models are pressed or workstation builds, and thickness is one stated property among several rather than a verdict. Sound treatment is stated on every sheet, under three names: NoiseDefend on the Kraus models and the Delta, described as sound-absorbing pads with anti-condensation undercoating, Sound Guard on the Elkay, and a soundguard coating with thick rubber padding on the Ruvati. The descriptions agree on the mechanism, pads and coating on the outside of the bowl, while differing in vocabulary. A buyer comparing noise should note that every maker in the class fits treatment as standard, so the stated difference is the name and the coverage described, not presence or absence.

Certification is the last stated line, and it is consistent: the Kraus sheets and the Delta page state cUPC to ASME A112.19.3 and CSA B45.4, the Ruvati page states cUPC tested by IAPMO, and the Elkay sheet lists compliance with ASME A112.19.3 and CSA B45.4 for the sink and ASME A112.18.2 and CSA B125.2 for the accessory. Where a sheet revision date is printed it is worth a glance before fabrication, because two versions of one model’s sheet circulate with slightly different figures, as the KBU32 note in its product section records.

The 32 inch class rewards a buyer who reads dimension lines carefully: width for the cut-out, minimum cabinet in both directions, bowl dimensions for the work, and the included list for the contents of the box. Six models meet that reading: three workstation single bowls, one handmade single bowl, and two double bowls with divisions of the width.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.