Updated Nov 17, 2026· 16 min read

Key takeaways

  • Pro audio mixers to use with Turbosound iP2000 column systems compared on main outputs, channel counts and control, from compact digital desks to analog boards.

The iP2000 accepts a mixer feed through two combo jack inputs rated at a nominal 4 dBu sensitivity, so the pro audio mixers to use with turbosound ip2000 setups are desks with balanced main outputs, enough channels for the act, and monitor sends the column system cannot provide from its own three-channel mixer section alone.

The Turbosound iNSPIRE iP2000 is a 1,000 watt powered column loudspeaker with a 12 inch subwoofer, 16 midrange drivers of 2.75 inches and a 1 inch high frequency compression driver, giving a stated frequency response of 45 Hz to 20 kHz and a maximum SPL of 123 dB across a 120 degree horizontal dispersion. Its own mixer section is small on purpose: two analog inputs on combo jack and XLR sockets, a Bluetooth stereo streaming input, three-band equalization, factory presets for positioning and sound mode, and control from a single rotary encoder or an iPhone or iPad over Bluetooth. That covers a solo act with one microphone and a backing track. Anything larger runs out of inputs immediately, which is where an external desk takes over: the column keeps the amplification, dispersion and onboard DSP, while the mixer supplies the channels, monitor mixes, effects and recording outputs the performance needs.

Quick verdict

Every desk below feeds the iP2000 the same way, through balanced main outputs into the two combo inputs, so the verdict turns on channel count, monitor mixes and workflow. The X32 and TF3 bring full digital consoles, the CQ-18T packs digital mixing into a carry-on size, and the two analog boards keep hands-on faders.

Product Main outputs to the iP2000 Inputs Format Standout feature
Behringer X32 16 XLR outputs 32 mic preamps, 40 inputs Digital console 32 by 32 USB recording interface
Yamaha TF3 16 XLR outputs 24 mic and line inputs Digital console TouchFlow touchscreen operation
Allen & Heath CQ-18T 2 XLR main outputs 16 mic and line inputs Compact digital 7 inch touchscreen, built-in Wi-Fi
Yamaha MG16XU XLR and TRS stereo outputs 10 mic inputs Analog SPX effects with 24 programs
Mackie ProFX16v3 2 balanced XLR mains 11 mic preamps Analog GigFX engine with 24 effects

The connection itself is identical for all five. Run the mixer’s main left output into input A of the column and the main right output into input B, using XLR cables, and the pair of combo sockets carries the stereo mix. The host spec sheet rates those inputs at a nominal sensitivity of 4 dBu with a maximum input level of +22 dBu, so a desk run at sensible master levels sits comfortably inside the range the column expects. Owners who only need a mono feed can use a single input and keep the second socket free, and the Bluetooth input stays available for break music regardless.

How we selected

Selection started at the column, not the desk. The iP2000 product page was read first to fix the requirements: two combo jack and XLR inputs, 4 dBu nominal sensitivity, and a link output on XLR. Only mixers whose own opened pages document balanced main outputs on XLR, plus the channel count to justify an external desk, were considered.

Each mixer below was verified from its own opened product page, and every figure quoted, output counts, input counts, USB channel counts, dimensions, comes from that page. Compatibility is claimed only where the two pages support it: a mixer with balanced XLR main outputs connects to the column’s combo inputs, which accept XLR plugs, and line-level output ratings are compared with the input sensitivity the Turbosound page states. No maker endorses a pairing here, and none is implied. Desks whose opened pages did not state their main output connectors were left out, because the output connection is the whole point of this keyword. All five are current models sold for live sound work.

Pro audio mixers to use with turbosound ip2000 systems

Five desks follow, two full-size digital consoles, one compact digital mixer and two analog boards. Each entry states the output connection first, because that is what the column sees, then the input count and the tools that decide whether the desk suits a band, a worship team or a speaking event.

Behringer X32

The X32 is the full-production option: a 40-input, 25-bus digital console whose 16 XLR outputs include the main feed for the column, with 32 MIDAS microphone preamps and a 32 by 32 USB interface for recording the same show it mixes for the room, all in a desk that stores up to 100 scenes.

The console mixes 40 input channels across 25 buses, with a main LCR bus, 6 matrix buses and 16 mix buses, each carrying inserts, 6-band parametric EQ and full dynamics processing, plus 8 DCA groups and 6 mute groups. A virtual FX rack provides 8 true-stereo effect slots, and 25 fully automated motorized 100 mm faders keep the surface in step with scene recalls. Scenes let one desk serve a spoken event on Friday and a band on Saturday, recalling the whole setup while the column receives the finished stereo feed.

Outputs are the reason it leads this list. Sixteen XLR outputs plus 6 additional line inputs and outputs give the main pair for the column and leave the mix buses free for stage monitors or a recording feed, and ULTRANET connectivity supports the Behringer P-16 personal monitoring system. The 32 by 32 channel USB 2.0 interface records multitrack to a computer, and a USB type-A port takes uncompressed stereo recordings directly. The desk is large for a column system, 35.4 by 20.8 by 7.9 inches and 45.4 pounds, so it suits installed or regularly repeated setups more than one-person load-ins.

  • Pros: 16 XLR outputs cover mains, monitors and recording feeds; 100 scenes for repeat venues; 32 by 32 USB multitrack recording.
  • Cons: The largest and heaviest desk here; its depth of features is more than small acts will use.

Yamaha TF3

The TF3 pairs 24 recallable D-PRE microphone preamps on combo inputs with 16 XLR outputs and Yamaha’s TouchFlow operation, a touchscreen and Touch and Turn encoder workflow built for engineers who mix by tapping the channel they want and turning one knob to adjust it.

Behind the surface sit 48 input channels, 40 mono, 2 stereo and 2 returns, fed by 24 mic and line inputs on XLR and TRS combo sockets plus stereo line inputs. Twenty aux buses, 8 mono and 6 stereo, give monitor mixes for a full band, and 8 DCA groups keep related channels under single faders. DSP includes 8 effects and 10 graphic equalizers, and 25 motor faders, 24 channels plus a master, are 100 mm motorized units that follow scene memory recalls. Wireless control runs through the Yamaha StageMix app for the engineer and the MonitorMix app for performers adjusting their own mixes.

For the column pairing, two of the 16 XLR outputs carry the stereo main mix to inputs A and B, and the remaining outputs handle monitors and zones without touching the main feed. A 34 by 34 USB audio interface records multitrack to a computer, with 2-track recording to USB storage as the simpler option. The TF3 measures 716 by 225 by 599 millimeters and weighs 17.0 kilograms. Sampling runs at 48 kHz throughout.

  • Pros: 20 aux buses for band monitor mixes; TouchFlow touchscreen speeds up operation; 34 by 34 USB recording.
  • Cons: Larger than the compact options; app-based monitor control needs a wireless network in the venue.

Allen & Heath CQ-18T

The CQ-18T is the compact digital choice, an 18-input mixer with a 7 inch capacitive touchscreen, 96 kHz FPGA processing and built-in dual-band Wi-Fi, whose two balanced XLR main outputs are rated at +4 dBu, the exact nominal level the iP2000 inputs are specified around.

Sixteen mic and line preamps split between 8 XLR sockets and 8 combo XLR and quarter-inch sockets, joined by a balanced stereo line input, and every channel carries EQ, compression and gating. Four FX engines use signal-conscious reverb and delay units that respond to the incoming signal, and the desk adds working tools the others list differently: a gain assistant that sets preamp gain automatically, a feedback assistant that finds feedback frequencies at setup and watches for them during the show across all outputs, and an automatic mic mixer for speech applications.

Six quarter-inch mix outputs cover monitor mixes, and two assignable headphone outputs serve the engineer and a performer. Recording is built in rather than added on: a 24 by 22 USB-B interface and 24 by 22 SD card recording and playback run at the same time as the mix, and a dedicated Bluetooth input channel handles playback without using an analog input. Remote control comes from the CQ-MixPad and CQ4You apps over the built-in Wi-Fi. At 13.6 by 9.5 by 3.5 inches and 6.6 pounds, it is the desk a solo operator carries in the same trip as the column, and it runs from a 12 volt DC supply.

  • Pros: +4 dBu balanced main outputs match the column’s nominal input sensitivity; feedback and gain assistants speed setup; SD and USB multitrack recording built in.
  • Cons: No physical faders, mixing is touchscreen and app based; 18 inputs cap the size of band it can serve.

Yamaha MG16XU

The MG16XU is the analog mid-size board: 16 channels with up to 10 microphone inputs, main stereo outputs on both XLR and TRS phone connectors, four group buses and an SPX effects section with 24 programs, in a metal chassis with a rack mount kit in the box.

Eight mono mic and line channels use combo jacks and D-PRE discrete class-A preamps, with a pad switch on the mono inputs for hot signals, one-knob compressors for quick dynamic control and 3-band EQ with high-pass filters. Two further channels accept mic or line sources and two stereo line channels take playback devices, and every stereo channel also offers RCA inputs for sources such as CD players. Phantom power is +48 volts across the mic inputs. Four aux sends, one of them the effects send, feed monitor mixes or external processors, and the group buses let a section of the mix, the band minus the speakers, for example, sit on its own faders.

The main stereo outputs appear on XLR left and right and on TRS phone left and right, so the feed to the column’s combo inputs can use the balanced XLR pair while the TRS pair serves a recorder or a second zone. A 24-bit, 192 kHz 2-in, 2-out USB interface records the stereo mix to a computer or an iPad, and Cubase AI software is included as a download. The board measures 444 by 130 by 500 millimeters and weighs 6.8 kilograms, with an internal universal power supply.

  • Pros: XLR and TRS main outputs on the same stereo bus; group buses simplify section control; one-knob compressors suit volunteer operators.
  • Cons: Analog surface has no scene recall; USB recording is stereo only, not multitrack.

Mackie ProFX16v3

The ProFX16v3 states the pairing in its own words: its main outputs, two balanced XLR and two quarter-inch jacks, provide a line-level signal for running to an outboard amplifier or powered speakers, which is exactly the job the iP2000’s combo inputs are there to receive.

The 16-channel analog mixer carries 11 Onyx microphone preamps with up to 60 dB of gain, spread across 8 mono mic and line channels, three stereo channels that also accept mic inputs, and a final stereo channel with a 1/8 inch input or USB return. Channels 1 to 8 add single-knob compression and insert jacks for outboard gear, low-cut filters at 100 Hz with an 18 dB per octave slope switch on the mic channels, and every channel has EQ, mute and PFL solo. The GigFX effects engine holds 24 effects including reverbs, choruses and delays, fed from the fourth aux send.

Four subgroups with direct outputs and three monitor aux sends, two pre-fader and one switchable, give a small band its monitor mixes while the main fader drives the column feed, and a break button mutes the main, control room and headphone outputs together between sets. The USB interface runs 2 channels out and 4 channels in at 24-bit, 192 kHz for recording and playback with the included Waveform OEM software. A steel chassis with ABS side panels, 60 mm faders and a weight of 15.2 pounds at 17-5/8 by 4 by 20 inches keep it in the portable analog class.

  • Pros: Maker states the mains suit powered speakers directly; 11 preamps with 60 dB gain; subgroups and three monitor sends at an analog surface.
  • Cons: No scene memory, as with any analog board; USB return shares the last stereo channel with the 1/8 inch input.

Buying guide

A column system with two analog inputs makes the buying decision mostly about what happens before the feed arrives. Work through the host’s input specification, the shape of the feed, monitor requirements and the processing split between desk and column, and the right size of mixer usually becomes obvious.

Start from the two inputs on the column

The iP2000 gives an external mixer exactly two analog doors: input A and input B, both combo jack and XLR sockets, with a sensitivity of 4 dBu nominal, input impedance of 16 kilohms unbalanced and 33 kilohms balanced, and a maximum input level of +22 dBu. Everything a mixer sends arrives through those two sockets.

That specification is generous for a powered speaker. A maximum input level of +22 dBu means the column accepts hot line-level feeds without padding, and balanced inputs reject the hum that long cable runs across a stage can pick up. What the column does not provide is equally clear: no monitor outputs, no per-channel EQ beyond a shared three-band section, and no recording output. Those gaps, not raw power, are what the external mixer is bought to fill.

Matching levels: pro audio mixers to use with turbosound ip2000 inputs

Level matching is a comparison of two printed figures. On the column side, the nominal sensitivity is 4 dBu, the level the input is designed around. On the mixer side, the CQ-18T documents the cleanest match, balanced outputs at +4 dBu, which is the same reference point, so its meters and the column’s input stage agree by design.

For the other desks, the practical rule is to run the main fader so the mix sits at a healthy level on the mixer’s meters without pushing into the top of the scale, and let the column’s input gain, set from its rotary encoder or the app, do the final trim. The +22 dBu maximum input level leaves headroom for peaks above the nominal point. If a feed ever sounds strained at modest mixer levels, the fault is more likely a cable wired for the wrong socket type than a level problem, because a balanced cable into a balanced input is the quiet arrangement.

Decide between a stereo feed and a mono feed

Two inputs invite a stereo feed, and for music playback and keyboard-heavy acts the left and right main outputs of the desk into inputs A and B preserve the image the mixer creates. The column sums that feed into one point source, so the choice shapes balance rather than placement.

A mono feed is the better choice for speech-led events. Send one main output, or a mono sum where the desk offers it, into a single input and every seat hears the same balance from the 120 degree dispersion. The second input then stays free for a microphone plugged straight into the column, a useful backup for a host or celebrant, and the Bluetooth input still covers walk-in music. The desks here all support either arrangement; the choice is made per event, not per purchase.

Count the monitor mixes your performers need

The column’s wide dispersion lets performers hear the main mix from the stage area, and the maker’s description positions that coverage as removing the need for separate monitor wedges in many setups. Larger or louder acts still want their own mixes, and the number of independent sends is a hard limit set by the desk’s output count.

Count from the products above. The X32 offers 16 mix buses alongside its main outputs. The TF3 provides 20 aux buses in mono and stereo combinations. The CQ-18T has 6 mix outputs, enough for a small band’s wedges or in-ear feeds. The MG16XU sends four aux mixes, and the ProFX16v3 three monitor sends plus its effects send. A solo act needs none of these; a five-piece band with a drummer on in-ears needs at least three. Buy for the largest lineup the column regularly serves.

Let the desk carry the processing

The column’s own DSP is broad: positioning and sound mode presets, three-band EQ shared across the mix, and limiting that protects the drivers. It shapes the whole program at once. Per-source shaping, a gate on the drum kit, compression on one vocal, a graphic EQ on the main bus, has to happen at the desk before the stereo feed is summed.

The digital desks put EQ, compression and gating on every channel and add graphic equalizers on buses; the X32 adds a virtual FX rack of 8 stereo slots, the CQ-18T four FX engines with its feedback assistant, and the TF3 8 effects with 10 graphic equalizers. The analog boards give fixed per-channel tools, one-knob compressors and a single effects engine each, which is enough for voices and acoustic instruments and simpler for rotating volunteers to run.

Recording and playback from the same desk

A mixer in front of the column is also the natural recording point, because it hears every source before the mix is summed. The USB interfaces here range from the X32’s 32 by 32 channels and the TF3’s 34 by 34, through the CQ-18T’s 24 by 22 with parallel SD card recording, down to the stereo 2-in, 2-out interfaces of the two analog boards.

Decide what the recording is for. A stereo capture for review or a service archive needs only the analog boards’ USB output. A recording that might be remixed later needs multitrack, which means one of the digital desks, and the CQ-18T’s SD option removes the laptop from the rig entirely.

FAQ

Questions about pairing a desk with this column tend to repeat: whether the column needs a mixer at all, which cables the connection takes, how recording works, and what happens when a second column joins the system. The answers below stick to what the opened product pages state.

Can the iP2000 run without an external mixer?

Yes, for small formats. The column has an onboard 3-channel digital mixer with gain setting recall: two analog inputs on combo sockets and a Bluetooth stereo input, with three-band EQ, factory presets and remote control from an iPhone or iPad. A solo performer with a microphone and a phone fits that section comfortably.

The external desk becomes necessary when sources outnumber two analog inputs, when performers need individual monitor mixes, or when the event needs recording outputs and per-channel processing.

Which cables connect a mixer to the iP2000?

Standard balanced XLR cables, one per side. The mixer’s main left and right XLR outputs connect to input A and input B on the column, whose combo sockets accept XLR plugs. Balanced connections on both ends keep long runs across a stage quiet, and every desk in this list provides XLR mains.

Desks that also offer quarter-inch main outputs, the MG16XU and the ProFX16v3 among them, can use the jack half of the combo sockets instead, which is handy when the XLR pair is already feeding a recorder or a second zone. Set the column’s input levels after the desk’s main fader is at its working position.

Can pro audio mixers to use with turbosound ip2000 rigs record the performance?

Yes, and the column feed is unaffected, because recording taps the desk’s USB interface rather than anything on the speaker. The X32 records 32 channels each way over USB, the TF3 34 each way, and the CQ-18T 24 by 22 over USB or to an SD card in the desk itself, all while the stereo mains feed the room.

The analog boards record the finished stereo mix only, 2 channels in and out on the MG16XU at up to 24-bit, 192 kHz, and 2 out with 4 back on the ProFX16v3 at the same resolution. For an archive of the event that is usually sufficient; for a mix that will be rebalanced later, choose a digital desk.

Can I feed a second column system later?

The host specification lists a link output on XLR alongside the two inputs, which is the connection provided for passing signal onward from the column itself. A desk with spare outputs offers the other route: the X32 and TF3 each have 16 XLR outputs, so a second column can take its own pair of feeds with independent level.

Feeding from the desk keeps each system on its own output pair, which makes balancing two rooms simpler. Either way the connection is the same balanced XLR the first column uses.

What if my mixer only has quarter-inch main outputs?

The column still accepts the feed, because its inputs are combo sockets that take jack plugs as well as XLR. A balanced quarter-inch TRS cable from the desk’s main outputs into inputs A and B carries the same line-level signal, and the input sensitivity figures quoted for the sockets apply to the input as a whole.

Two of the desks here cover both cases on the same stereo bus: the MG16XU provides main stereo outputs on XLR and on TRS phone connectors, and the ProFX16v3 pairs its balanced XLR mains with quarter-inch main jacks. Owners of older boards with only unbalanced outputs should keep cable runs short, since the balanced input on the column cannot cancel hum picked up along an unbalanced run.

Conclusion

The iP2000 asks little of a mixer: two line-level feeds into combo inputs rated around a 4 dBu nominal sensitivity. The X32 and TF3 answer with digital consoles for bands and repeat venues, the CQ-18T matches the column’s level and adds assistants, and the MG16XU and ProFX16v3 keep it analog and direct. Pick by channel count and monitor mixes.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.