Key takeaways
- Compare 6 of the best 8 channel mixers with echo and eq, from powered Rockville and Pyle boxes to consoles with DSP delay, graphic EQ and Bluetooth built in.
Echo and EQ are the two tools that turn a plain 8 channel mixer into a vocal performance board, and the best 8 channel mixers with echo and eq build both into the box: a delay or echo effect that adds space and repeats to a voice, plus channel and master equalization that shapes tone and tames feedback in live rooms.
How to Choose 8 Channel Mixers With Echo and EQ
Choosing among 8 channel mixers with echo and eq starts with three questions: how the echo is generated and adjusted, where the EQ sits in the signal path, and whether the mixer powers speakers itself. The six models here answer those questions differently, and the right pick depends on your speakers and your room.
Echo, delay and reverb are related but not identical
Echo and delay describe the same family of effect: the signal repeats after a short interval, and the mixer controls how long the gap is and how many repeats trail away. Reverb is different, simulating the reflections of a room rather than distinct repeats, so the two are not interchangeable.
Makers label these controls loosely, so each listing in this guide was checked for the actual wording. Rockville states adjustable delay and echo on the RPM85 and adjustable echo and delay on the RPM80BT. Pyle fits echo and reverb master controls on the PMX840BT, while the PMXU83BT maker Q&A describes its effect set as 16 different delay variations. The Depusheng DX8 manual names its controls REP for echo and DLY for delay time, which is the clearest labeling of the group.
Channel EQ versus graphic EQ
Channel EQ shapes one input at a time, typically with high, mid and low knobs, and it is where you fix a harsh microphone or a boomy guitar. Graphic EQ shapes the whole mix through sliders at fixed frequencies, and it is the tool for ringing out feedback and adjusting to the room.
The strongest setups in this guide offer both layers. The Pyle PMXU88BT pairs a 3-band EQ on every channel with a 7-band graphic equalizer on the main output. The Rockville RPM85 combines per-channel bass and treble with an illuminated 5-band graphic EQ, and the PMX840BT pairs independent channel EQ with a master 5-band graphic section. Consoles without a graphic section, such as the DX8 and PMXU83BT, rely on channel EQ alone, which is workable in controlled rooms.
Powered or unpowered
Three of the six mixers here are powered, meaning the amplifier is built in and passive speakers connect directly: the Rockville RPM85 and RPM80BT and the Pyle PMX840BT. The other three are consoles that output line level and need powered speakers or a separate amplifier behind them.
Powered boxes simplify a portable rig and reduce cable runs, at the cost of weight: the RPM85 weighs 25.4 pounds before speakers. Consoles stay light and cool on a desk, and they slot into an existing PA or recording setup, but they add an amplification decision to the purchase. Neither approach sounds better by default; the choice is about what you already own and how often the rig moves.
The 6 Best 8 Channel Mixers With Echo and EQ
The six best 8 channel mixers with echo and eq below were verified on opened product and manual pages, with effect types, EQ layouts and power figures taken from the makers’ own wording. They span three powered mixers and three consoles, covering complete portable systems and desk-based setups.
Rockville RPM85
The Rockville RPM85 is an 8-channel powered mixer whose listing states adjustable delay and echo effects, per-channel reverb, bass and treble controls, and an illuminated 5-band graphic EQ. It is rated at 300 watts RMS per channel into 4 ohms, with 8 balanced XLR inputs and 8 1/4 inch TS line inputs.
Output into 8 ohm speakers is rated at 225 watts RMS per channel, and +15 volt phantom power runs condenser microphones. Bluetooth, USB and SD playback cover backing tracks without extra sources. At 25.4 pounds and 19 x 12 x 7.5 inches, it stays a one-person carry, and because the amplifier is built in, the only extras a small band or karaoke rig needs are passive speakers and cables.
Rockville RPM80BT
The Rockville RPM80BT is an 8-channel powered mixer that the maker describes with adjustable effects, naming echo and delay directly, plus individual volume, reverb, bass and treble controls per channel and a 5-band EQ. Its amplifier is rated at 250 watts RMS per channel into 8 ohms, 500 watts in total.
The maker also quotes a 2400 watt peak figure, 1200 watts per channel, which describes bursts rather than sustained output. Inputs run to 8 XLR and 8 1/4 inch TRS, phantom power is a full +48 volts, and a remote control and power cable are included. Fan vent cooling suits long event days. Compared with the RPM85, it trades some continuous power for stronger phantom support and remote operation.
Pyle PMX840BT
The Pyle PMX840BT is an 8-channel powered stage mixer rated at 800 watts maximum output, and its maker lists EQ and master effects control of level, echo and reverb. A master 5-band graphic equalizer works at 60, 250, 1K, 4K and 12K Hz with plus or minus 12 dB of boost and cut per band.
Channel EQ offers plus or minus 15 dB of range with independent volume, EQ and effects adjustment per channel, and an effects loop on RCA and 1/4 inch connectors accepts external processors. Two limits deserve note: the maker’s Q&A confirms there is no phantom power, so it suits dynamic microphones, and Bluetooth is version 2.1+EDR with a stated range of 30 feet or more. USB and SD readers, a carry handle and a cooling fan complete the stage box.
Pyle PMXU83BT
The Pyle PMXU83BT is a compact 8-channel console with an FX section built around a 16-bit DSP processor, and in the maker’s own Q&A the effect set is described as 16 different delay variations. Its 3-band channel EQ provides plus or minus 15 dB at 12 kHz shelving on the high band and at 2.5 kHz on the mid band.
At 9.3 x 10.8 x 2.6 inches it is the smallest mixer in this guide, and it adds +48 volt phantom power, Bluetooth 4.0 streaming and a USB connection for playback and computer linking. As an unpowered console it needs powered speakers or an amplifier behind it, which suits home studios, streaming desks and small venues that already own amplification and want delay-based vocal effects in a tiny footprint.
Pyle PMXU88BT
The Pyle PMXU88BT is an 8-channel console with 4 XLR and combo inputs, 16 DSP effects chosen with a PROGRAM control and shaped with a PARAMETER control, and per-channel FX sends with a dedicated FX SEND fader. Its EQ pairs a 3-band section on all channels with a 7-band graphic equalizer on the main output.
The graphic equalizer adjusts the signal sent to the main outputs and engages with an EQ IN switch, and a sub output with its own fader supports a separate low-frequency feed. An MP3 player with Bluetooth and USB, +48 volt phantom power across the XLR inputs, and a steel chassis round out the design. It measures 12.5 x 16.3 x 3.66 inches and weighs 8.4 pounds, the most control-heavy console here.
Depusheng DX8
The Depusheng DX8 is an 8-channel console in an ultra-thin chassis with an ultra musical 3-band EQ on all channels and a built-in reverb effect. Its user manual documents the echo side directly, with an Echo Frequency and Depth Adjustment control marked REP and a delay time control marked DLY.
Effect sends are available per channel, so repeats can be timed and blended for one vocalist without washing the whole mix. The DX8 also provides +48 volt phantom power and Bluetooth, USB and MP3 playback. Published dimensions and weight figures for this model conflict between listings, so confirm the current figures with the seller before planning a case around it.
Across the six, the echo control styles divide into three kinds: continuously adjustable knobs on the Rockville pair and the DX8, preset banks on the two Pyle consoles, and master echo and reverb controls on the PMX840BT. Performers who ride the effect during a song will prefer the knob-based models, while hosts who set one sound and leave it will be just as well served by presets.
8 Channel Mixers With Echo and EQ Compared
Comparing 8 channel mixers with echo and eq side by side shows the real split in this group: powered mixers quote amplifier watts and carry graphic EQ for the room, while consoles quote effect counts and EQ bands and leave power to your speakers. The table matches effect wording and EQ layout to each model.
| Mixer | Type | Effects | EQ | Power or output note |
|---|---|---|---|---|
| Rockville RPM85 | Powered | Adjustable delay and echo | 5-band graphic EQ | 300 W x 2 RMS at 4 ohms |
| Rockville RPM80BT | Powered | Adjustable echo and delay | 5-band EQ | 250 W x 2 RMS at 8 ohms |
| Pyle PMX840BT | Powered | Echo and reverb master controls | 5-band graphic EQ | 800 W max output |
| Pyle PMXU83BT | Console | 16 DSP delay variations | 3-band EQ per channel | USB interface, line level out |
| Pyle PMXU88BT | Console | 16 DSP effects | 3-band EQ plus 7-band graphic EQ | Sub output, line level out |
| Depusheng DX8 | Console | Reverb plus echo and delay controls | 3-band EQ per channel | Bluetooth and USB, line level out |
Read across the rows and three patterns emerge. The powered models concentrate on master control: one graphic EQ for the room and one effects section for the whole mix, which is fast to run during a show. The consoles spread control across channels instead, with per-channel EQ everywhere and, on the PMXU88BT, per-channel effects sends. The DX8 sits between the two philosophies, a console with dedicated echo and delay knobs that behave more like a powered box’s master effect.
Reading the power figures
Powered mixer ratings mix continuous and peak numbers, so compare like with like. The RPM85 quotes 300 watts RMS per channel into 4 ohms and 225 watts into 8 ohms, the RPM80BT quotes 250 watts RMS per channel into 8 ohms beside a 2400 watt peak total, and the PMX840BT quotes an 800 watt maximum.
RMS figures predict sustained volume into a stated speaker load, while peak and maximum figures describe short bursts. That is why the Rockville numbers, quoted per channel into named loads, are the more conservative guide to continuous output, and why the PMX840BT figure should be read as a ceiling rather than a running level. Speaker impedance matters too: the same amplifier delivers less continuous power into 8 ohms than into 4 ohms, as the RPM85 ratings show directly.
Setting Echo and EQ Together
Echo and EQ interact: repeats emphasize whatever frequencies the channel EQ leaves prominent, so a bright vocal with heavy echo can turn harsh, and a muddy vocal with long repeats loses its words. Set the channel EQ first with the effect off, then bring the echo in underneath the voice.
A simple vocal echo recipe
Start with the channel EQ flat, raise the vocal until it sits clearly over the music, then add echo with a medium delay time and low repeat depth so each phrase ends with one or two soft repeats. If the words start to blur, shorten the delay before reaching for more EQ.
On the RPM85 and RPM80BT that means small moves on the delay and echo controls while listening from the audience position. On the PMXU83BT it means stepping through the delay variations until the repeat spacing matches the tempo. On the DX8 it means balancing the REP depth against the DLY time, and on the PMXU88BT it means setting the per-channel FX send so only the lead vocal carries the effect while backing channels stay dry.
Feedback control with graphic EQ
When a microphone starts to ring, the graphic EQ is the fix: lower the slider nearest the ringing frequency a few dB at a time until the ring stops. Small cuts at one or two bands usually restore headroom without thinning the whole mix, which is why every powered model here includes a graphic section.
The PMX840BT spaces its five bands at 60, 250, 1K, 4K and 12K Hz with plus or minus 12 dB of range, the PMXU88BT offers seven bands on the main output, and the Rockville models use illuminated 5-band sections that stay readable on a dark stage. Work one slider at a time and stop as soon as the ring disappears; deep cuts across several bands hollow out the vocal you were trying to feature.
Setup, Inputs and Playback
Beyond echo and EQ, the practical differences are phantom power, input counts and how each mixer plays backing tracks. All six models provide Bluetooth and USB-based playback, but microphone support varies, and one model in this group cannot power condenser microphones at all.
Phantom power differences
Phantom power decides which microphones you can use. The RPM80BT, PMXU83BT, PMXU88BT and DX8 provide +48 volt phantom power for condenser microphones, the RPM85 provides +15 volt phantom power, and the PMX840BT provides none, as its maker confirms in its Q&A, so it suits dynamic microphones only.
That single specification can rule a model in or out faster than any effect feature. A vocalist with a condenser microphone needs one of the +48 volt models, or the +15 volt RPM85 where the microphone accepts the lower voltage. A dynamic-microphone act gives up nothing on the PMX840BT and gains its powered output and media readers, so check the microphone before the mixer.
Bluetooth, USB and SD playback
Every mixer here streams or plays tracks without a separate source device. The Rockville models and the PMX840BT add SD or USB media reading for standalone playback, while the consoles add USB computer connections that suit recording and streaming as well as live playback.
Versions differ: the PMX840BT uses Bluetooth 2.1+EDR at a stated 30 feet or more, and the PMXU83BT uses Bluetooth 4.0. For karaoke and event work, media readers matter because the show continues from a card or drive even when a phone disconnects. For streaming and recording, the console USB connections on the PMXU83BT and PMXU88BT are the more useful path, feeding a computer directly.
Counting inputs honestly
Channel counts and input counts are different numbers, and the gap decides whether a band fits. The Rockville models provide a microphone input on every channel, while the Pyle PMXU88BT reaches eight channels with four microphone inputs and the rest of its panel given to line sources.
The PMX840BT mixes its sources differently again: 3-pin low impedance balanced microphone inputs, 1/4 inch line and high impedance inputs, a 3.5mm aux input for phones and MP3 players, and RCA tape play and record pairs. The RPM80BT adds an RCA aux input beside its XLR and TRS panel, and the PMXU88BT manual documents tape input and output sockets plus aux and return jacks that receive an external reverb or delay unit. Count microphones first, then keyboards and players, and the right panel usually picks itself.
Matching the Mixer to Your Gig
The best match depends on the room and the role: a karaoke host needs fast echo controls and media playback, a small band needs inputs and feedback control, and a streamer needs a quiet console with a USB connection. The six models divide cleanly across those jobs.
For karaoke and event hosts
Karaoke and event work rewards powered mixers, because one box drives the speakers and the echo sits on a master control. The PMX840BT adds USB and SD readers so tracks play without a phone, and the RPM80BT adds a remote control and Bluetooth streaming for hosts who move around the room.
Hosts who run the same room weekly also benefit from graphic EQ memory in their hands: once the RPM85 or PMX840BT sliders are set for the room, the same positions work night after night. Singers ask for more echo than engineers expect, so a clearly labeled echo control, like the master effects section on the PMX840BT, speeds up requests between songs.
For small bands and streamers
Small bands need microphone inputs first: the RPM85 and RPM80BT each accept eight XLR microphones, while the PMXU88BT accepts four and serves line sources on the rest. Streamers are better served by the compact consoles, the PMXU83BT and DX8, which sit on a desk and connect over USB.
Bands playing varied rooms should weigh the graphic EQ sections heavily, because feedback conditions change with every stage. Streamers should weigh size and fan noise instead: the PMXU83BT is the smallest unit here at 9.3 x 10.8 x 2.6 inches, and neither it nor the DX8 carries a power amplifier stage, which keeps the desk setup simpler and cooler over long sessions.
Frequently Asked Questions
These answers cover the questions buyers ask most about 8 channel mixers with echo and eq: whether echo and delay are the same control, how many microphones each model really accepts, and how the powered and console designs differ in daily use at home, on stage and in small venues.
Is echo the same as delay on these mixers?
On the mixers in this guide, yes in practice: echo is the audible repeat that a delay circuit produces, and makers use both words for the same control family. Rockville lists adjustable delay and echo together, and the Depusheng DX8 manual separates echo adjustment from delay time.
How many microphones can I connect at once?
It depends on the input panel rather than the channel count. The Rockville RPM85 and RPM80BT each provide 8 XLR inputs, so eight microphones can run together, while the Pyle PMXU88BT provides 4 XLR and combo inputs within its 8 channels and serves line sources on the remaining channels.
Do I still need speakers with a powered mixer?
Yes, but only passive ones. A powered mixer such as the RPM85, RPM80BT or PMX840BT contains the amplifier, so it drives passive speakers directly through its speaker outputs, while the console models output line level and need powered speakers or a separate power amplifier behind them.
Which EQ matters more, channel or graphic?
They solve different problems, and the stronger mixers here include both. Channel EQ fixes the source, removing boom from one voice or adding presence to one instrument, while graphic EQ fixes the room and the overall mix and serves as the feedback-fighting tool during a live show.
Echo gives a voice its space and EQ gives it its shape. Choose a powered model, the Rockville RPM85 or RPM80BT or the Pyle PMX840BT, for a system with graphic EQ, or a console, the Pyle PMXU83BT or PMXU88BT or the Depusheng DX8, for powered speakers. Match phantom power and inputs first, then pick the echo controls you will enjoy using.