Updated Nov 16, 2026· 13 min read

Key takeaways

  • Six dry herb vaporizers with on-demand heating, deep temperature control and printed chamber and battery specs, compared on the controls their listings print.

Control depth is the thread through this list: on-demand convection, a calibration dial, reprogrammable presets and app-linked precision. No listing promises results for any reader, so the six vape for experienced weed smokers picks below are ranked by what their pages print about heating, chamber size and control, nothing more.

Quick verdict

The Tinymight 2 is the control flagship here, with pure convection, on-demand heat in 2 to 5 seconds and a dial that can be recalibrated. The Firefly 2+ heats on demand in about 3 seconds across 200 to 500 degrees F. The Angus Enhanced adds a 100 W halogen heater and presets that can be rewritten from a computer.

The FURY 3 is the precision pick with a small titanium chamber and single-degree control, the Crafty+ splits its control between three on-device presets and a Bluetooth app, and the MIQRO-C shrinks the format to under 100 g with four preset heat paths. Every figure below is printed on the listing for that device, and where a listing omits a figure, such as bowl size on the Firefly 2+, the entry says so.

Product Heating Chamber as printed Control Main limit
Tinymight 2 Pure convection, on-demand or session 0.05 to 0.25 g, adjustable Numbered dial 0 to 10 No screen and no app
Firefly 2+ Full convection, on-demand Not stated on the listing App or on-device presets Bowl size not printed
Angus Enhanced Convection and radiant heat 0.2 to 0.25 g Five presets, reprogrammable Heaviest here at 268 g
Healthy Rips FURY 3 Convection with radiant heat 0.175 to 0.205 g Single-degree buttons, OLED Small chamber by design
Storz & Bickel Crafty+ Hybrid convection and conduction Not stated on the listing Three presets plus app Preset steps on the device
DaVinci MIQRO-C Conduction 0.25 g per maker table Four Smart Paths 20 to 30 minutes per charge

How we selected

Selection favored control a listing can prove on paper: on-demand heating, heat-up time in seconds, temperature range, whether presets can be changed, and whether chamber size can be adjusted. Each device also needed printed battery and chamber information, or an honest gap where the listing prints none, so no spec rests on a review.

The list is fully separate from the chamber-and-runtime list in the companion guide for this batch. Different readers weight control differently, so heating method was recorded for every device: three of the six heat purely or mainly by convection, one is hybrid, one mixes convection with radiant heat from a halogen bulb, and one is a compact conduction unit with preset paths. Claims about who a device suits are framed as reading of the spec sheet, never as a promise about the session itself.

Six picks: vape for experienced weed smokers

Each entry covers the heating system first, then the control surface, chamber and battery figures as printed, and the limit that matters most. Pros and cons stick to the listing, and the buy-if and skip-if lines translate the spec sheet into the routine each device fits, without claiming any device performs better than its printed figures say.

Tinymight 2

The Tinymight 2 is built around a pure convection heater rated at 70 W on this listing, with on-demand and session modes and a heat-up time of 2 to 5 seconds. The herb chamber sits in the glass mouthpiece and adjusts from 0.05 to 0.25 g by sliding the cooling unit with the built-in stir tool, so load size is a setting, not a fixed bowl.

Temperature is set on a numbered dial from 0 to 10, spanning 140 to 250 degrees C by default; the listing maps position 1 to about 140 degrees C, position 5 to about 180, position 7 to about 200, and position 10 to 230 degrees C in session mode or 250 on demand. A hidden calibration routine can shift the whole range. Power is a removable 3000 mAh 18650 cell, one included, which the seller’s testing puts at roughly 5 to 8 sessions per charge at moderate settings; charging is USB-C with no pass-through use. The body is handmade in Finland from solid wood at 6.1 x 3.7 x 8.8 cm and 186 g, with a color LED, vibration feedback and a stealth mode, no display and no app. The warranty is 3 years.

  • Pros: on-demand convection; adjustable chamber down to 0.05 g; recalibratable dial; removable battery
  • Cons: no screen or app; no pass-through charging; session counts are seller testing figures

Buy if: you want on-demand heat and a dial you can tune to your own reference points. Skip if: you read temperatures off a screen or control devices from a phone.

Firefly 2+

The Firefly 2+ heats on demand with full convection, reaching temperature in about 3 seconds per draw rather than holding a session temperature. Its listed range runs from 200 to 500 degrees F, equal to 93 to 260 degrees C, the widest span in this list, set through the companion app on iOS or Android or through on-device presets.

The vapor path is borosilicate glass and the body is magnesium alloy, with airflow listed as a 33 percent increase over the original Firefly 2. The rechargeable lithium-ion battery is user-replaceable and charges on a dock with a USB 3.0 cable, reaching 80 percent in about 20 minutes and a full charge in about 45 minutes. Activation is touch-sensitive, with no button to hold. The listing covers dry herb as the primary material and concentrates with the included pads. One figure is missing: this listing does not print a bowl capacity in grams, so none is claimed here.

  • Pros: heat in about 3 seconds; widest printed range here; glass vapor path; fast dock charging
  • Cons: bowl capacity not printed on the listing; app needed for the full range; per-draw heating style

Buy if: you take single draws spaced out and want each one heated on demand. Skip if: you run timed sessions at one steady temperature.

Angus Enhanced

The Angus Enhanced heats with a 100 W halogen bulb through ruby balls, mixing convection with radiant heat, a system no other device in this list uses. Five presets sit at 180, 190, 200, 210 and 220 degrees C, a boost step adds 10 degrees C up to 230, and the presets can be reprogrammed between about 150 and 230 degrees C from a desktop tool.

The stainless steel chamber holds 0.2 to 0.25 g and can be loaded down to about 0.05 g for a microdose. Heat-up is 45 to 60 seconds. Two removable 18650 cells power the device; the maker ships it without cells and this listing includes two 3000 mAh cells, good for about 5 to 10 sessions per charge, with USB-C charging in about 2 hours. An airflow dial runs from wide open to fully closed, the body is high-temperature polycarbonate with a stainless steel air path at 268 g with batteries, and the session auto-off is 5 minutes. The box is generous: three glass mouthpieces at 50, 70 and 90 mm, a sidecar bubbler, a 14 and 18 mm water pipe adapter, a loading funnel, screens, O-rings, a brush and a carry case. The warranty is 1 year.

  • Pros: halogen and ruby heating; reprogrammable presets; microdose-friendly chamber; full glass accessory kit
  • Cons: heaviest device here; 45 to 60 second heat-up; cells not included by the maker

Buy if: you want to rewrite the preset ladder and use glass pieces at home. Skip if: the device needs to disappear into a pocket.

Healthy Rips FURY 3

The FURY 3 is the precision instrument of the list: convection heating with a slight radiant component, a titanium chamber 11 mm across with a printed capacity of 0.175 to 0.205 g, and single-degree control across 280 to 430 degrees F. Heat-up is about 20 seconds, and a dosing capsule is included for repeatable loads in that small chamber.

The Class A 2300 mAh lithium polymer battery is listed at 70 to 85 minutes per charge, charges in 75 to 90 minutes over USB-C at 5V and 1.5A, and supports pass-through charging. The body measures 90.5 x 51.8 x 27.4 mm at 5.6 oz, with an OLED screen that flips, haptic feedback, a session timer adjustable from 3 to 7 minutes, a glass vapor path and an alloy unibody shell. An extra-long glass cooling stem of 3 inches is part of the package. The maker lists a one-year free replacement warranty plus a lifetime half-price replacement plan, in Dark Gray, Blue and Teal Green finishes. The maker’s store notes its devices are for legal dry plants only, not oils or liquids.

  • Pros: single-degree control; pass-through charging; dosing capsule and long glass stem included; strong warranty terms
  • Cons: chamber tops out at 0.205 g; small format means shorter sessions per load

Buy if: you work in small, measured loads and adjust heat degree by degree. Skip if: your loads run larger than 0.2 g.

Storz & Bickel Crafty+

The Crafty+ splits its control in two. On the device are three presets at 180 degrees C (356 degrees F), 195 degrees C (383 degrees F) and 210 degrees C (410 degrees F), named Basic, Booster and Superbooster. Connected over Bluetooth to the Android or web app, it opens up to full precision control; the phone is needed only for those fine steps.

Heating is hybrid convection and conduction with a heat time of 60 seconds, the filling chamber is ceramic-coated, and a dosing capsule is included. The technical spec table on the listing gives a built-in battery, with life stated as 5 to 9 sessions and up to 90 minutes in the page text, charging in about 1 to 2 hours over USB-C. Automatic shutoff comes after 2 minutes idle and can be adjusted. The cooling unit is PEEK. The warranty is 2 years, plus 1 more year with registration.

  • Pros: preset simplicity with app precision on demand; hybrid heating; dosing capsule included; 3 years of warranty once registered
  • Cons: 60 second heat time; fine control needs the app; chamber capacity not printed on the listing

Buy if: you want one button for routine sessions and an app for detailed ones. Skip if: every adjustment must happen on the device itself.

DaVinci MIQRO-C

The MIQRO-C is the compact entry: conduction heating in a glass-lined ceramic oven, a zirconia and glass airpath, and an adjustable zirconia pearl that shrinks the oven. The maker’s comparison table lists this oven at 0.25 g. Four Smart Paths run 5-minute sessions across bands of 350 to 370, 370 to 390, 390 to 410 and 410 to 430 degrees F.

The removable 18350 battery is rated at 900 mAh, giving 20 to 30 minutes of runtime, about 3 to 4 sessions, and it charges over USB-C in about 90 minutes with passthrough use listed. The body measures 23 x 34 x 80 mm and stays under 100 g on this listing, with haptic feedback, a stealth mode and a 10 mm water piece adapter in the box. The warranty is a 5-year limited plan when the device is registered within 30 days. This listing does not print a heat-up time, so none is stated here.

  • Pros: under 100 g; adjustable oven via the pearl; passthrough charging; 5-year limited warranty
  • Cons: 20 to 30 minutes per charge; preset paths only; heat-up time not printed on the listing

Buy if: size comes first and sessions are short. Skip if: runtime matters more than pocket space.

Buying guide

Control is not one feature but a stack of them: how heat is delivered, how fast it arrives, how finely it can be set, and whether the settings can be changed. This section separates those layers using only the figures printed above, so each device can be judged on the kind of control it actually offers rather than on a general claim of quality.

On-demand heat for vape for experienced weed smokers

On-demand devices heat per draw instead of holding a temperature. The Tinymight 2 lists 2 to 5 seconds to heat and the Firefly 2+ about 3 seconds, against 20 seconds for the session-style FURY 3, 45 to 60 seconds for the Angus Enhanced and 60 seconds for the Crafty+. The trade is patience at the start against heat applied only while drawing.

On-demand heating also changes battery math. A device that heats for seconds at a time spends its charge differently from one that holds temperature through a 5-minute session timer, which is why session counts and minutes per charge are printed beside each pick rather than merged into one ranking.

Precision, presets and programmable ladders

Three approaches appear here. Single-degree control, on the FURY 3 across 280 to 430 degrees F, suits small steps. Fixed presets, on the Crafty+ and Angus Enhanced, suit a repeated routine. The Angus goes further: its five presets can be rewritten from a desktop tool, and the Tinymight 2 dial can be recalibrated, so the ladder is adjustable.

Preset paths are the fourth style: the MIQRO-C runs four Smart Paths as rising bands over 5-minute sessions. None of these is more correct than the others. The useful question is whether the reader changes temperature often, in which case steps and ladders matter, or settles on one setting, in which case presets are simpler.

Chamber size and microdosing

Printed chamber figures run small by design: 0.05 to 0.25 g adjustable on the Tinymight 2, about 0.05 g minimum loads in the 0.2 to 0.25 g Angus chamber, 0.175 to 0.205 g on the FURY 3 and 0.25 g on the MIQRO-C, whose pearl shrinks the oven. Two listings, the Firefly 2+ and the Crafty+, print no chamber figure and are compared on control instead.

Adjustability is the real spec to read. A chamber that only works full behaves differently from one designed to meter small loads, and the listings that print a minimum load, the Tinymight 2 and the Angus Enhanced, are the ones that document that range on paper.

Batteries, pass-through and spares

Power arrangements split three ways. Removable cells appear on the Tinymight 2 (one 18650), the Angus Enhanced (two 18650 cells) and the MIQRO-C (18350), so a spare restores full runtime. Built-in batteries appear on the FURY 3 and the Crafty+, with pass-through charging listed for the FURY 3 and for the MIQRO-C, but not for the Tinymight 2.

Charge times run from about 45 minutes for a full Firefly 2+ dock charge to about 2 hours for the Angus Enhanced. For a reader who rotates devices or keeps spares, removable cells are the flexible option; for a reader who charges nightly, the built-in designs ask for less handling.

App control and on-device control

Two devices lean on a phone for their deepest settings: the Firefly 2+ opens its full 200 to 500 degrees F range in the app, and the Crafty+ adds precision control over Bluetooth while keeping three presets on the device. The other four keep everything on the hardware, from the Tinymight 2 dial to the Angus desktop reprogramming tool.

App control adds range and records settings, but it also adds a dependency on a phone, an account or a connection. On-device control is narrower on paper and self-contained in practice. The listings print enough to choose: which settings live where is stated for every device in this guide.

FAQ

These answers cover the control questions this keyword raises most: what on-demand heating changes, whether an app is required, how small loads are handled, how the halogen system differs, and what the warranty figures on these listings actually say. Each answer stays with printed specs and names the device it belongs to.

Does a vape for experienced weed smokers need an app?

No. Four of the six devices here keep all control on the hardware. The Firefly 2+ uses its app for the full temperature range but keeps on-device presets, and the Crafty+ runs three presets on the device with precision control in the app. An app widens the settings on those two models; it is not a condition for detailed control in general.

The Tinymight 2 reaches a similar depth with a dial and a calibration routine, which shows how much of the app question is about interface taste rather than capability.

What is the difference between on-demand and session heating?

An on-demand device heats when a draw starts and cools between draws, with listed heat-up times of 2 to 5 seconds on the Tinymight 2 and about 3 seconds on the Firefly 2+. A session device heats the chamber and holds temperature for a timed period, such as the 3 to 7 minute timer on the FURY 3 or the 5-minute sessions on the MIQRO-C paths.

The practical difference is pacing. On-demand suits spaced draws; session heating suits a continuous sitting. Both styles appear in this list because the listings print the timings that separate them.

Which of these devices handles the smallest loads?

On printed figures, the Tinymight 2 adjusts its chamber from 0.05 to 0.25 g, and the Angus Enhanced lists loads down to about 0.05 g in a 0.2 to 0.25 g chamber. The MIQRO-C uses an adjustable pearl to shrink its 0.25 g oven. The FURY 3 chamber is small overall at 0.175 to 0.205 g, filled as one load or through its dosing capsule.

A printed minimum load matters because a chamber designed for small amounts meters them by design, while a large chamber partly filled depends on packing to behave the same way.

How does the halogen heater in the Angus Enhanced work?

The listing describes a 100 W halogen bulb heating synthetic ruby balls, which then heat the air and add radiant heat to the chamber. It is the only heater of its kind in this list, and it explains the 45 to 60 second heat-up: the balls hold the heat, and the five presets, plus a 10 degree C boost step, are read against that thermal mass.

The same listing notes the presets can be reprogrammed from a desktop tool between about 150 and 230 degrees C, which is a deeper level of adjustment than any fixed ladder offers.

What do the warranty figures on these listings say?

They vary. The MIQRO-C lists a 5-year limited warranty with registration inside 30 days. The Tinymight 2 lists 3 years. The Crafty+ lists 2 years plus 1 with registration. The FURY 3 lists one year of free replacement plus a lifetime half-price replacement plan. The Angus Enhanced lists 1 year.

Registration windows are the detail most often missed: two devices here extend or activate cover only when the device is registered within a stated period after purchase.

Conclusion

For control on paper, the Tinymight 2 leads: on-demand convection, a recalibratable dial and a chamber that adjusts to 0.05 g. The Angus Enhanced is the deep-tinker pick, with reprogrammable presets and a halogen heater. The FURY 3 is the precision pick. Each was chosen on printed control specs, and no listing here promises any result in use.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.