Key takeaways
- Six outdoor range hoods for gas grills compared on stated airflow, blower setup, duct size, filters, mounting height and construction, from maker documents.
An outdoor grill hood has a harder job than an indoor one: it must pull smoke and grease out of open air, often against a breeze. The six range hoods for gas grills below were chosen from maker manuals, specification sheets and detailed listings, and each entry states the airflow, duct size and mounting figures its maker publishes.
Quick verdict
The Blaze BLZ-42-VHOOD moves the most air, at 2,000 CFM from two motors. The Trade-Wind S724812CD and the Coyote C1HOOD48 each state 1,200 CFM in 48 inch widths, and the Zephyr Cypress reaches 1,200 CFM at the top of its stated blower range. The Hestan GVP42 and the Vent-A-Hood Designer Series each state 900 CFM with equivalent figures of 1,350.
The right pick depends on the installation more than the headline number. The Blaze needs two separate 8 inch exhaust paths. The Zephyr mounts lowest, at 30 to 36 inches above the cooking surface. The Coyote adds a Heat Sentry thermostat that adjusts blower speed on its own. The Trade-Wind is the widest series here, running to 72 inches, and the Hestan and Vent-A-Hood entries filter grease without conventional baffle filters, which changes the cleaning routine.
| Model | Width | Stated airflow | Duct | Grease handling | Mounting height |
|---|---|---|---|---|---|
| Trade-Wind S724812CD | 48 in | 1,200 CFM internal blower | 10 in collar | Stainless steel baffle filters | Canopy structure 36 in above the surface |
| Zephyr Cypress AK7836BS | 36 in | 450 to 1,200 CFM | 10 in round | Pro Baffle filters, 3 | 30 to 36 in |
| Blaze BLZ-42-VHOOD | 42 in | 2,000 CFM, two motors | Two 8 in outlets | 6 baffle filters, 2 grease trays | 36 to 40 in |
| Hestan GVP42 | 42 in | 900 CFM, 1,350 equivalent | 10 in round combined | Shield system, no baffle filters | Not stated on the opened pages |
| Coyote C1HOOD48 | 48 in | 1,200 CFM internal blower | 10 in square-to-round, with damper | 4 baffle filters | Not stated on the opened page |
| Vent-A-Hood 42-Inch Designer Series | 42 in | 900 CFM, 1,350 equivalent | 10 in round minimum | Magic Lung centrifugal system | Not stated on the opened page |
How we selected
Each hood below is a model its maker or listing presents for outdoor grill installations, with airflow and duct figures stated on an opened page: maker manuals and installation guides, a maker specification sheet, or a detailed product listing. Indoor under-cabinet hoods were excluded.
Figures are quoted as the makers state them, and two makers use an “equivalent CFM” figure alongside the rated CFM; both numbers are given where a maker publishes both, and the buying guide explains the term. Sones are quoted where stated. Where an opened page does not state a figure, such as mounting height for three of these models, the entry says the maker does not state it rather than borrowing a number from another brand’s instructions. One excluded model makes the point about fit: its maker states it is not recommended for outdoor kitchens or for heavy grilling.
Range hoods for gas grills, model by model
The six hoods split into two airflow classes: three models at 1,200 CFM or above, and three at 900 CFM with maker-stated equivalent figures of 1,350. Widths run from 36 to 48 inches in the featured models, with one series extending to 72 inches. All six are stainless steel canopy or chimney designs for wall or canopy mounting over a grill.
Trade-Wind S724812CD
The Trade-Wind S7200CD series is the widest line here, with widths from 36 to 72 inches, all at 32 inches of front-to-back depth. The maker’s installation guide lists internal-blower models at 1,200 CFM for the 36, 42 and 48 inch widths, and 2,300 CFM for the 54 to 72 inch widths. The featured 48 inch model has a 10 inch duct collar.
The blower has three speeds, the filters are stainless steel baffles, the light control is dimmable, and the guide describes a rear discharge conversion for the ducting. Two installation rules from the guide matter before purchase: a hood installed away from a wall needs a minimum of 3 feet of weatherproof roof coverage on the unprotected sides, and in a custom canopy the canopy structure sits 36 inches above the cooking surface. Duct covers are sold separately. This is the pick for wide grill islands where one of the broader widths, up to 72 inches, matches the cooking surface.
- Pros: series runs to 72 inches wide; 1,200 CFM at 48 inches and 2,300 CFM in the largest widths; convertible ducting with rear discharge described; dimmable lighting.
- Cons: duct covers sold separately; installation guide requires weatherproof roof coverage on open sides; largest widths need two 10 inch duct collars.
Buy if your grill island is wide and you want one hood series that scales from 36 to 72 inches. Skip if your outdoor kitchen has no roof coverage to add, since the maker’s own installation rules assume weather protection above the hood.
Zephyr Cypress AK7836BS
The Cypress is a 36 inch outdoor canopy in 304-grade stainless steel, from a series that also runs to 42, 48 and 54 inches. Zephyr’s specification sheet states a blower range of 450 to 1,200 CFM, sound levels of 3.5 to 9 sones, three speeds on metallic knob controls, and a depth of 32 inches. The duct is 10 inch round, vertical or horizontal.
The sheet lists three Pro Baffle filters on this width, and states that the maker lists dishwasher cleaning for them. Lighting is two 35-watt halogen lamps with dual levels on the 36 and 42 inch models. The mounting height range is 30 to 36 inches above the cooking surface, the lowest stated range in this group, which suits lower ceilings and covered patios. The stated warranty is 3 years on parts and 1 year on labor, the only warranty term published among these six hoods.
- Pros: 304-grade stainless canopy; mounting range down to 30 inches; stated warranty of 3 years parts and 1 year labor; horizontal or vertical ducting.
- Cons: 1,200 CFM is the top of a range, so mid settings move less air; 9 sones at the top speed is the loudest figure stated here; four filters on the wider widths to clean.
Buy if your covered patio limits mounting height and you want a stated parts warranty. Skip if your grill is wider than 36 inches and the wider Cypress widths are not available to you, or if blower noise at full speed is a concern.
Blaze BLZ-42-VHOOD
The Blaze hood is the airflow leader: its manual states 2,000 CFM in total from two motors, each vent cap rated at 1,000 CFM. Each motor has four speed settings, and there are four adjustable halogen lights. The manual is explicit that the two vent outlets, sized for 8 inch pipe, should keep separate exhaust paths rather than being combined.
Grease handling uses six stainless steel baffle filters, three front and three rear, plus two grease trays, and the manual states the filters can be cleaned in a dishwasher. Mounting instructions allow 36 to 40 inches between the top of the cooking surface and the bottom of the hood, with a minimum vertical distance of 36 inches. The unit connects with a 110V plug-in cord. The twin-duct requirement is the deciding factor: a kitchen that can only run one duct run cannot use this hood as the maker intends.
- Pros: highest stated airflow at 2,000 CFM; four speeds per motor; six baffle filters and two grease trays; plug-in 110V connection.
- Cons: needs two separate 8 inch exhaust paths; highest mounting range here at 36 to 40 inches; two motors means two sets of controls to manage.
Buy if your grill produces heavy smoke and your roof or wall can take two duct runs. Skip if only one duct path is possible, or if your canopy structure cannot meet the 36 inch minimum mounting distance.
Hestan GVP42
The Hestan GVP42 is a 42 inch Pro Canopy rated at 900 CFM from a blower package of one dual and one single unit. Hestan publishes an Equivalent CFM figure of 1,350 for the model and tells buyers to use that figure for cross-brand comparisons. Sound is stated at 6.3 sones at the highest fan speed, and the electrical supply is 115 VAC, 60 Hz.
The combined discharge is 10 inch round through the maker’s transition piece; run separately, the dual blower alone needs 8 inch round and the single 6 inch round. Each blower assembly has its own speed control, and a separate knob controls lighting intensity. There are no baffle filters: grease is captured in the blower housings and shields, which is the cleaning routine to expect. The same manual covers the GVP48 and GVP54 at 1,200 CFM with two dual blowers, a 12 inch round transition and 6.6 sones. The opened pages do not state a mounting height for this series.
- Pros: maker publishes an equivalent figure for cross-brand comparison; separate speed control per blower; no baffle filters to wash; wider 1,200 CFM siblings in the same manual.
- Cons: rated 900 CFM is the joint-lowest headline figure here; mounting height not stated on the opened pages; shield system needs its own cleaning routine.
Buy if you prefer blower-level control and a filter-free grease path, and you are comparing brands on the maker’s equivalent basis. Skip if you want the mounting height confirmed in the same document as the airflow, or if 900 rated CFM is below the airflow you need.
Coyote C1HOOD48
The Coyote entry is a 48 inch chimney-style wall mount in 304 stainless steel, sold with the maker’s 1,200 CFM internal blower. The listing states a variable-speed motor control and a Heat Sentry thermostat that automatically adjusts blower speed as temperatures change, which is the only automatic control among these six hoods.
Depth is 30 inches, the shallowest here. Four commercial-style baffle filters are removable, and the maker lists dishwasher cleaning for them. Two 50-watt halogen lights are fitted, and the hood ships with a 10 inch square-to-round transition with a damper; the duct cover is sold separately. Stated dimensions are 48 inches wide, 15 inches high and 30 inches deep, weight is 89 pounds, and the warranty is 1 year. The listing describes the hood as suited to 42 inch grills, one size down from its own width, which is the correct way to size a hood over a grill.
- Pros: Heat Sentry thermostat adjusts the blower on its own; 304 stainless construction; 1,200 CFM in a 48 inch chimney; transition piece with damper included.
- Cons: 1-year warranty is short; duct cover sold separately; 30 inch depth is the shallowest coverage here; mounting height not stated on the opened page.
Buy if you want the blower to manage itself as grill temperatures swing, over a grill up to about 42 inches. Skip if a longer warranty matters to you, or if your grill needs the full 32 inch depth the other canopies provide.
Vent-A-Hood 42-Inch Designer Series
The Vent-A-Hood entry pairs a 42 inch Designer Series hood with two blower units, a dual and a single, for a stated 900 CFM and a maker equivalent of 1,350 CFM. The maker’s blower table also lists 300 CFM for a single unit, 600 for the dual alone and 1,200 CFM for two duals, so the same hood can be specified at four airflow levels.
The featured configuration includes the maker’s standard transition and needs a 10 inch minimum round duct, with sound stated at 6.3 sones. Instead of baffle or mesh filters, the Magic Lung blower uses centrifugal filtration, so there are no filter panels to remove and wash. Halogen lighting runs to three lamps on the 42 to 53 inch widths. One caution belongs with this entry: the opened document is the general Designer Series specification, so the outdoor-rated configuration for a grill installation should be confirmed with the maker before ordering.
- Pros: four blower configurations from 300 to 1,200 CFM in one hood line; centrifugal filtration with no filter panels; transition included; 6.3 sones at the featured rating.
- Cons: outdoor configuration needs confirming with the maker; 900 CFM in the featured setup is the joint-lowest here; mounting height not stated on the opened page.
Buy if you want to choose your airflow level inside one hood design and skip filter washing. Skip if you need the outdoor rating confirmed on the same page as the specifications, or if you prefer a hood documented specifically for grill installations.
Buying guide
Outdoor hood selection turns on four stated figures: the airflow rating and the basis behind it, the duct size and path, the mounting height over the cooking surface, and the way the hood handles grease. The headings below take each in turn, using the numbers the six makers publish, and close with sound levels and controls.
How much airflow range hoods for gas grills need
Start from the ratings as stated. Three of these hoods state 1,200 CFM or more: the Blaze at 2,000 CFM across two motors, and the Trade-Wind and Coyote at 1,200 CFM each, with the Trade-Wind series reaching 2,300 CFM in its 54 to 72 inch widths. The Zephyr states a range up to 1,200 CFM. The Hestan and Vent-A-Hood state 900 CFM.
Bigger grills and heavier smoke loads argue for the higher ratings, but ducting decides how much of the rating reaches the outdoors. A 1,200 CFM hood on an undersized or sharply bent duct will not move its rated air. Match the hood to the duct the maker specifies, which is 10 inch round for most models here, and treat the airflow figure and the duct figure as one decision rather than two.
Duct size and discharge direction
Five of the six hoods work around a 10 inch round duct: the Trade-Wind uses a 10 inch collar, the Zephyr a 10 inch round duct that can run vertical or horizontal, the Hestan combines its blowers into a 10 inch round discharge, the Coyote a 10 inch square-to-round transition with damper, and the Vent-A-Hood specifies a 10 inch minimum round duct.
The Blaze is the exception, with two 8 inch outlets that its manual says to keep on separate paths. Direction matters too: the Trade-Wind guide describes a rear discharge conversion, and the Zephyr allows horizontal runs, both useful when a roof penetration is not possible. Before ordering, walk the intended duct path and count the turns; every maker figure in this guide assumes the duct arrangement its document describes.
Baffle filters, shields and centrifugal systems
Three grease systems appear here. Baffle filters are the common route: stainless baffles on the Trade-Wind, three Pro Baffle filters on the Zephyr, six baffles plus two grease trays on the Blaze, and four removable baffles on the Coyote. On the Zephyr and Coyote pages, and in the Blaze manual, the maker lists dishwasher cleaning for the filters.
The Hestan and Vent-A-Hood take the other routes. Hestan captures grease in blower housings and shields, with no baffle filters to remove. Vent-A-Hood’s Magic Lung uses centrifugal filtration instead of baffle or mesh panels. Neither system removes the cleaning job; both move it from filter panels to housings and interior surfaces. Choose based on which routine fits your kitchen habits, not on any claim that one system needs no cleaning.
Mounting height and coverage
Only three makers state a mounting figure on the opened pages. The Zephyr sheet gives 30 to 36 inches above the cooking surface. The Blaze manual allows 36 to 40 inches, with a 36 inch minimum. The Trade-Wind guide places a custom canopy structure 36 inches above the surface.
The Hestan, Coyote and Vent-A-Hood pages do not state a height, so those figures must come from the maker before installation. Coverage is the companion question. Hood depth here runs from 30 inches on the Coyote to 32 inches on the Trade-Wind and Zephyr, and width should meet or exceed the grill below: Coyote’s own listing pairs its 48 inch hood with 42 inch grills. The Trade-Wind guide also requires weatherproof roof coverage, at least 3 feet on open sides, which is a structural point to settle before the hood is ordered.
Sones, lighting and controls
Sound is stated for three models: the Zephyr at 3.5 to 9 sones across its range, and the Hestan and the Vent-A-Hood at 6.3 sones at their featured ratings. The Zephyr’s low end, at its lowest blower setting, is the quietest figure published here; its top end is the loudest. The other three makers do not state sones on the opened pages.
Controls differ in kind. The Coyote’s Heat Sentry adjusts blower speed automatically with temperature. The Hestan gives each blower assembly its own speed control plus a separate lighting knob. The Blaze runs four speeds per motor on retractable knobs, the Zephyr three speeds on metallic knobs, and the Trade-Wind a three-speed blower with dimmable lights. Lighting is halogen across the group, from two lamps on the smaller Zephyr and the Coyote to four on the Blaze and the wider Trade-Wind widths.
FAQ
The questions below cover the installation points that decide most purchases in this group: mounting height, whether twin outlets can share one duct, what is and is not included in the box, and how to read the equivalent airflow figures two makers publish.
How high should range hoods for gas grills be mounted?
Follow the maker of the hood you buy, because the stated ranges differ. Zephyr publishes 30 to 36 inches above the cooking surface for the Cypress. Blaze allows 36 to 40 inches with a 36 inch minimum for its vent hood. Trade-Wind’s guide sets a custom canopy structure 36 inches above the surface.
Those are the only three heights stated on the opened pages. For the Hestan, Coyote and Vent-A-Hood models, the opened pages do not state a mounting height, and the figure should be confirmed with the maker before the duct and structure are built. Mounting too low crowds the cook and exposes the hood to direct flame heat; mounting too high lets smoke escape past the canopy edges, especially outdoors where air moves.
Can one duct combine two blower outlets?
Not on the Blaze, which is the model the question usually concerns. Its manual rates each vent cap at 1,000 CFM and instructs that the two 8 inch exhaust paths stay separate rather than being combined into one run. Combining them would work against the maker’s stated design and its 2,000 CFM total rating.
The Hestan shows the opposite design done by the maker itself: its two blower assemblies discharge through one combined 10 inch round transition that Hestan supplies for the purpose. The difference is who designs the junction. A factory transition sized for the combined flow is part of the specification; a field-made junction on the Blaze is not.
Are these hoods sold with duct covers?
Often not, and the opened pages say so in two cases: Trade-Wind and Coyote both list the duct cover as sold separately. The Coyote does include its 10 inch square-to-round transition with a damper, and the Vent-A-Hood’s featured configuration includes its standard transition, so transitions and covers are separate questions on the same order.
Accessories to confirm before checkout are the duct cover, any transition not listed as included, and, on the Trade-Wind, the second 10 inch collar set that the largest widths require. The check is about completeness of the order: a hood that arrives without its cover leaves the duct run exposed and the installation unfinished.
What does equivalent CFM mean?
It is a comparison figure the maker publishes alongside the rated CFM. Hestan rates the GVP42 at 900 CFM and publishes an Equivalent CFM of 1,350, with instructions to use it for cross-brand comparisons. Vent-A-Hood publishes the same pairing: 900 CFM rated, 1,350 equivalent, rising to 1,800 equivalent at its 1,200 CFM configuration.
The careful approach is to compare rated figures with rated figures and equivalent with equivalent, and to note which basis a headline number uses. On a rated basis the Blaze leads this group at 2,000 CFM. On the equivalent basis the Hestan and Vent-A-Hood present their 900 CFM designs as comparable to 1,350 CFM hoods. Both statements come from the makers’ own documents, and the entries in this guide keep the two bases separate.
Conclusion
The Blaze BLZ-42-VHOOD leads at 2,000 CFM, provided two duct paths are possible. The Trade-Wind series suits wide islands up to 72 inches, the Zephyr Cypress mounts lowest and states the only parts warranty, and the Coyote adds automatic blower control. The Hestan GVP42 and Vent-A-Hood Series trade headline CFM for filter-free grease handling.