Key takeaways
- Five gas cooktops with downdraft compared on published specs only: width, burner output in BTU, vent CFM, fan speeds, grate type and fuel conversion notes.
A downdraft cooktop pulls smoke and steam down through the surface instead of up into a hood, which suits islands and open kitchens. This guide compares prices for gas cooktops with downdraft by looking at the published specs that separate the models: width, burner output, vent strength and fan speeds.
Quick verdict
Two makers supply every model in this group. The KitchenAid 36 inch model pairs five burners with a 300 CFM exhaust rating, the JennAir 36 inch models add a melt cap on the low burner, and the two 30 inch models keep the same vent idea in a smaller cutout for tighter kitchens and island runs.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| KitchenAid 36 inch 5 Burner Gas Downdraft Cooktop KCGD506GSS | 36 inch gas downdraft | Wide cooking surface | 300 CFM exhaust rating, 3-speed fan control | Duct-free conversion kit not included |
| JennAir Euro-Style 36 inch JX3 Gas Downdraft Cooktop JGD3536GS | 36 inch gas downdraft | Low simmer control | 5,000 BTU ultra-low burner with melt cap | Duct-free use needs an optional kit |
| JennAir JX3 36 inch Black Gas Downdraft Cooktop JGD3536GB | 36 inch gas downdraft, black | Dark finish kitchens | 297 CFM Motor Class blower, JX3 vent system | Black finish only in this listing |
| KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS | 30 inch gas downdraft | Smaller cutouts | Same 300 CFM exhaust rating as the 36 inch model | Four burners instead of five |
| JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS | 30 inch gas downdraft | Published per-burner output | Four burners listed from 5,000 to 17,000 BTU | Listing pages disagree on the blower figure |
The split to notice first is width. Three models sit at 36 inches with five burners, and two sit at 30 inches with four, so your existing cutout settles half the choice before any burner figure is read. Within each width, the makers trade small advantages: a melt cap here, a higher published vent figure there, a black finish on one twin.
How we selected
Only gas cooktops with a vent built into the cooking surface were considered, because that built-in vent is the whole point of the keyword. Models with a separate pop-up vent accessory, electric downdraft models and standard gas cooktops that rely on an overhead hood were all left out of this comparison group.
Each model below was read on a maker or listing page that publishes its burner output, its vent rating and its fan speeds. Those three numbers decide how the cooktop behaves with a stockpot on full boil and a saucepan at a bare simmer, so a model with no published vent rating had no place in the table above.
Width was the third filter. The group splits cleanly into 36 inch models with five burners and 30 inch models with four, and the right group depends on your cutout, not on habit. Conversion notes were recorded as well, since a household on liquid propane needs the kit question settled before anything else.
Finish variants were treated as separate models only where a page lists them that way. The JennAir 36 inch line appears below in both its stainless Euro-Style form and its black form, because the two carry different model numbers and different listings, while their burner and vent figures stay in the same published family.
Gas downdraft cooktops in this roundup
Five models follow, three at 36 inches and two at 30 inches, all gas, all with the vent built into the surface. Burner output runs from 5,000 BTU simmer burners to 17,000 BTU high burners across the group, and every model lists three fan speeds, so the real differences sit in width, finish and burner layout.
KitchenAid 36 inch 5 Burner Gas Downdraft Cooktop KCGD506GSS
The maker lists this 36 inch cooktop with five burners and a downdraft ventilation system that needs no separate hood. Its burner set pairs a 17K BTU Professional Burner and a 15K BTU Professional Burner with a 5K BTU Even-Heat Simmer Burner, giving a wide spread between a rolling boil and a gentle simmer.
The vent side is listed with a 300 CFM exhaust rating and a 3-speed fan control, so steam capture can be matched to the job instead of running at one fixed draw. Full-width cast-iron grates cover the surface, which lets heavy pots slide from burner to burner, and the maker lists electronic ignition with automatic re-ignition.
For fuel, the maker lists an LP conversion kit with the cooktop, while a duct-free conversion kit is listed as not included. A household that cannot run ductwork should note that second line early, because venting downward into a cabinet run is a different plan from ducting the exhaust outside the house.
- Pros: strongest published vent rating in this group; five burners; two high-output burners
- Cons: duct-free kit not included; 36 inch width needs a wide cutout
Buy if you cook on several burners at once and want the vent built in. Skip if your cutout is 30 inches or your kitchen plan depends on duct-free venting out of the box.
JennAir Euro-Style 36 inch JX3 Gas Downdraft Cooktop JGD3536GS
The maker lists five sealed burners on this 36 inch model, topped by a 17,000 BTU Ultra-High Output Burner and anchored at the low end by a 5,000 BTU Ultra-Low Output Burner with a Melt Cap. That melt cap is a small detail with a daily job: holding chocolate or butter at a low, steady heat.
Ventilation comes from the JX3 Downdraft Ventilation System with three speeds and a 297 CFM Motor Class blower, a figure the maker publishes in its own class terms. The burners are listed as brass burners with a removable base, which speaks to cleaning and to long service on the parts that see the most heat.
The maker lists DuraFinish Protection on the stainless steel models, and lists the cooktop as convertible to duct-free ventilation with an optional kit. Like the KitchenAid above, the duct-free route is possible but not packed in the box, so the venting plan belongs in the decision from the start.
- Pros: melt cap on the low burner; brass burners; sealed burner design
- Cons: duct-free kit is optional, not included; blower figure sits just below the KitchenAid rating
Buy if low, controlled heat matters as much as high output in your cooking. Skip if you want the highest published vent rating here or a black finish, which the next model covers.
JennAir JX3 36 inch Black Gas Downdraft Cooktop JGD3536GB
The listing presents this model as the black finish version of the 36 inch JX3 line, with five burners, a 17,000 BTU ultra-high output burner and a 5,000 BTU ultra-low output burner with a melt cap. The listing describes the surface as porcelain coated steel with DuraFinish protection in its question section.
The vent figures match its stainless sibling: a JX3 downdraft system with three speeds and a 297 CFM Motor Class blower, per the listing. The listing also lists the cooktop as LP convertible, which keeps it open to households running liquid propane rather than natural gas from a street line.
Finish is the reason this model exists as its own entry. A black surface changes how a kitchen reads and how it shows dust, splashes and grate marks day to day, while the burner and vent hardware underneath stays in the same family as the stainless model described just above.
- Pros: black finish over the same JX3 hardware; melt cap included; LP convertible per the listing
- Cons: finish is the only real change from its sibling; dark surfaces show dust plainly
Buy if your kitchen design calls for a black cooktop surface with downdraft venting. Skip if you prefer stainless steel, since the model above gives the same burner layout in that finish.
KitchenAid 30 inch 4 Burner Gas Downdraft Cooktop KCGD500GSS
The maker lists this 30 inch model with four burners and the same downdraft ventilation approach as its wider sibling, needing no separate hood. The burner names carry over as well: a 17K BTU Professional Burner, a 15K BTU Professional Burner and a 5K BTU Even-Heat Simmer Burner lead the published set.
The vent rating also carries over, with a 300 CFM exhaust rating and a 3-speed fan control on the maker page, which means the smaller cooktop does not give up exhaust strength to fit its cutout. For a compact kitchen or an island in a smaller home, that is the figure that keeps this model in the conversation.
The maker lists an LP conversion kit and notes that a duct-free conversion kit is not included, the same pairing as the 36 inch model. What changes is elbow room: four burners crowd sooner when a stockpot, a skillet and a saucepan all need heat at the same time on a weeknight.
- Pros: full 300 CFM vent rating at 30 inches; high-output burners kept from the larger model
- Cons: four burners crowd with large pots; duct-free kit not included
Buy if your cutout is 30 inches and vent strength is your first concern. Skip if you regularly run three large pots at once, since the wider models give each pot more room.
JennAir 30 inch JX3 Gas Downdraft Cooktop JGD3430GS
The listing publishes the fullest burner map in this group for this 30 inch model: left front at 17,000 BTU, right rear at 15,000 BTU, right front at 10,000 BTU and left rear at 5,000 BTU. Knowing which corner holds which output helps when a big pot and a small saucepan swap places mid-recipe.
The JX3 downdraft system is listed with three vent speeds, and the listing spec table gives a 310 CFM Motor Class figure, while the feature text on the same page repeats a lower figure from the larger model. The spec table is the careful source here, and the disagreement is worth knowing about before you compare numbers across brands.
The listing also publishes a cutout width of 28 5/8 inches, a cutout depth of 21 1/2 inches and a net weight of 46 lb, plus LP conversion listed as yes with the kit included. Published cutout figures at this level of detail make planning a replacement far easier than working from the nominal width alone.
- Pros: per-burner output published; cutout dimensions published; LP kit listed as included
- Cons: listing text and spec table disagree on the blower figure; four burners only
Buy if you are replacing an older 30 inch unit and want exact cutout figures first. Skip if you need five burners or you want a single, undisputed vent figure on the page.
Buying guide
A downdraft gas cooktop is two appliances in one cutout: a burner set and a vent. Judge both halves with the points below, and confirm each figure on the maker or listing page for the exact model, because burner layouts and vent ratings change between widths that share a model family name.
One habit helps throughout: keep each maker’s own terms. KitchenAid publishes an exhaust rating, while JennAir publishes a Motor Class figure, and those labels are not interchangeable parts of one scale. Comparing the labels as printed, model by model, gives a fairer picture than forcing every vent into a single ranking.
What drives prices for gas cooktops with downdraft on the spec sheet
Width, burner count and vent hardware drive the spread between these models more than finish does. A 36 inch model carries five burners and longer grates, a 30 inch model carries four, and both sizes here publish similar vent ratings, so the step between them is about cooking room rather than exhaust strength.
Burner hardware adds its own layer. Brass burners, a melt cap on the low burner and sealed burner bases are listed features on the JennAir pages, while the KitchenAid pages lead with burner names and grate coverage. Read the feature list for the model in front of you rather than assuming the families match.
Match the vent rating to your cooking style
The published vent figures in this group sit close together, from 297 CFM Motor Class on the JennAir pages to a 300 CFM exhaust rating on the KitchenAid pages, with one listing spec table at 310. Those numbers are stated in different terms by different makers, so treat them as a rough band rather than a photo finish.
What matters in use is the match between steam load and fan speed. Three speeds appear on every model here, letting a low simmer run a quiet low draw while a hard boil gets the top setting. A cook who fries often will use the top speed daily; a gentle cook may rarely leave the first.
Plan the duct path before choosing a model
Every model here can vent downward, but the duct-free route is listed as an optional kit on the JennAir pages and as a kit not included on the KitchenAid pages. That means the venting plan, ducted through the floor or converted to duct-free, has to be settled before the cooktop choice is final.
Ducted venting moves air out of the house, while duct-free setups filter and recirculate it. The listing pages name the kits as separate parts, so a kitchen with no path for ductwork should confirm kit availability for the exact model at the same time as the cooktop itself is chosen.
Read the burner map, not just the burner count
Five burners with two high-output positions behave differently from five burners with one. The models here publish their strongest burners at 17,000 BTU or 17K BTU and their gentlest at 5,000 BTU or 5K BTU, and one 30 inch listing maps all four positions, which is the most useful layout information in the group.
Think about your largest pot and your smallest saucepan together. The big pot wants the high burner and room around it, and the small pan wants the low burner that will not scorch a sauce. A layout that puts both within easy reach beats a higher total count that crowds them together.
Settle the fuel question early
All five models are gas cooktops, and the pages address liquid propane conversion directly: kits are listed as included with the KitchenAid models and the 30 inch JennAir, and the black JennAir model is listed as LP convertible. A home without a natural gas line should treat that line of the spec sheet as the first filter.
Conversion is a one-time job done at installation, and the kit question is far easier to settle on paper than after delivery. If the listing is silent or unclear for the model you want, treat that silence as a stop sign and get the answer for the exact model number before going further.
FAQ
These answers use only figures published on the maker and listing pages for the five models above. Where makers state the same idea in different terms, the answer keeps their terms separate rather than blending them into one number that no page actually printed for that model.
Where can I find current prices for gas cooktops with downdraft?
On the maker page or the listing page for the exact model number, since figures there belong to that model and that moment. This guide compares the published specs instead, because burner output, vent ratings and cutout figures stay steady while the figures on a page change with the season and the seller.
Use the model numbers in the product headings above when you look, since downdraft lines share family names across widths and finishes. A 30 inch and a 36 inch model in the same family are different products with different cutouts, and the model number is what keeps the search on the right one.
Is a downdraft vent as strong as an overhead hood?
The pages here publish vent figures around the 300 CFM mark for these cooktops, with three fan speeds on every model. An overhead hood works with rising heat and steam, while a downdraft vent pulls air down across the cooking surface, so the two designs ask different things of the same plume of steam.
For the kitchens these cooktops are built for, islands and peninsulas where a hood is awkward or unwanted, the built-in vent is the practical answer. The published ratings in this group are close to one another, so the choice between these models turns more on burners and width than on vent strength.
Can these cooktops vent without ductwork?
Yes, with a conversion kit, according to the pages. The JennAir maker page lists conversion to duct-free ventilation with an optional kit, and the KitchenAid pages list a duct-free conversion kit as not included, which means the path exists for both families but the part is separate in each case.
Plan for that part at the same time as the cooktop. A duct-free setup filters and returns air to the room rather than sending it outside, and the kit is model-specific, so the kit for one family does not carry over to the other, whatever the widths involved.
Why are there no 6 or 7 burner models in this roundup?
Because the maker and listing pages behind this guide publish downdraft gas cooktops at five burners and below. The widest models here, at 36 inches, carry five burners each, and no currently listed model in this category publishes a sixth or seventh burner alongside a built-in downdraft vent.
Cooks who need more burners than that usually move to a rangetop or a range with an overhead hood, which is a different product category with different venting. Within the downdraft category itself, five burners on a 36 inch surface is the current top of the published range.
What cutout do the 30 inch models need?
One listing publishes exact figures for its 30 inch model: a cutout width of 28 5/8 inches and a cutout depth of 21 1/2 inches, with a net weight of 46 lb. The other 30 inch model is sold by its nominal width, and its maker page is the place to confirm the cutout before ordering.
Nominal width is a label, not a measurement. Two cooktops sold as 30 inch models can ask for slightly different cutouts, and an island or stone counter leaves little room for error, so the published cutout line for the exact model number is the figure to hand to your installer.
Conclusion
Pick the KitchenAid 36 inch model for the strongest published vent rating, the JennAir 36 inch models for the melt cap and brass burners, and either 30 inch model when the cutout rules. In every case, settle the duct path and the fuel kit first, because those two answers narrow this group fast, and the burner map settles whatever is left.