Updated Nov 16, 2026· 14 min read

Key takeaways

  • Six heat sealing tapes and kits for smokers compared: roll widths, lengths, Nomex and felt materials, adhesive types, and the one printed temperature rating.

A heat sealing tape for smokers is the gasket strip that closes the gap between a smoker lid and its body, and this guide compares six tapes and kits sold for that job, setting out the widths, lengths, materials, and temperature wording that each product page actually prints, including the five pages that print no number.

What heat sealing tape for smokers is sold as

Heat sealing tape for a smoker is a strip of heat-rated gasket material that sits on the rim where the lid meets the body of the cooker. When the lid closes, the strip compresses and fills the thin gap that would otherwise let smoke and heat escape around the edge during a long cook.

The six products in this guide come in two forms. Four are universal rolls of self-adhesive gasket tape that the owner cuts to length and presses around the rim. Two are kits shaped around one cooker family: a kettle kit that pairs a gasket with a tube of RTV adhesive, and a kamado kit sold by the cooker maker itself as the replacement seal for its own grills. The materials printed on the pages split the same way. Two rolls are Nomex, three products are felt, and the kettle kit lists a gasket plus RTV adhesive without naming a fibre.

The strip can sit on either side of the joint. The kettle kit in this guide installs on the lid side, as its maker page states, while the universal rolls can be pressed around the edge of the lid or the body rim, following the wording on the Smoker Chef listing. Placement matters less than coverage: the strip has to run the full circumference without a break at the join, because a single unsealed inch is where smoke finds its way out. Gaskets are also wear parts. The Smoker Chef listing describes scraping off the old fried gasket before the new one goes on, and the Big Green Egg maker page sells its kit as the way to restore a seal that has worn, which is why replacement tape exists as a category at all.

Temperature wording is where the pages differ most. Of the six product pages opened for this guide, only one prints a temperature number at all: the listing for the Big Green Egg kit states that the gasket withstands extreme heat up to 625 degrees Fahrenheit, or 330 degrees Celsius. The other five pages describe their material as high temp or high heat without giving a figure. This guide records the wording exactly as printed and does not assign a rating to any product whose page leaves the number out.

How to choose heat sealing tape for smokers by width, thickness and length

Three measurements decide whether a gasket tape fits a given smoker: the width of the strip, its thickness, and the length on the roll. The pages in this guide print some of those numbers and leave others out, so the comparison below separates what each maker states from what the page does not say.

Width and thickness come first. Four of the six products print a half-inch width. Thickness splits the rolls into two groups: the two Nomex rolls and one felt roll sit at one eighth of an inch, while the GriAddict felt roll is a quarter inch thick, the thickest strip in this guide. A thicker felt suits a lid with a visible gap or a factory gasket that has worn flat, because there is more material to compress. A thinner strip suits a tight lid that already closes evenly. The kettle kit, the Big Green Egg kit, and the Onlyfire roll do not print a width or thickness on the pages opened, because each is sold by cooker model rather than by strip dimensions.

Length matters on the universal rolls. Two products print a 20 foot total, supplied as two rolls of 10 feet each, which lets the owner run one roll around the lid and keep the second for the body rim or a later replacement. The LavaLock grey roll and the Onlyfire roll do not print a length on the pages opened, so an owner choosing either should measure the rim circumference of the cooker and compare it against the size information on the listing page before ordering. The two fitted kits avoid the question entirely: the kettle kit is cut for 22.5 and 26.75 inch kettles, and the Big Green Egg kit is coded by grill size.

Adhesive type is the last difference. The rolls and the Big Green Egg kit use a self-stick backing that the owner peels and presses into place. The kettle kit works differently: the box includes RTV adhesive alongside the gasket, and the maker page states that the kit installs on the lid side of the kettle. Cure time also appears on one page only. The Smoker Chef listing instructs the owner to close the lid and wait at least 12 hours for better fixation after sticking the gasket down.

The six gasket tapes and kits, compared

The table below lines the six products up on the figures their pages print. Where a page prints no figure, the table says so rather than filling the gap, because a gasket bought on an assumed width or an assumed temperature rating is a gasket that may not fit or may not suit the cooker.

Product Form Width Thickness Length Material Temperature rating as printed
Weber Kettle GASKET kit 22.5 26.75 LavaLock Brand Kit with RTV adhesive Not printed Not printed Cut for 22.5 and 26.75 kettles Gasket with RTV adhesive Not printed
Big Green Egg High-Performance Gasket Kit 113726 Fitted kit roll Not printed Not printed Coded by grill size Felt Up to 625°F / 330°C
LavaLock 1/2″ x 1/8″ High Temp Nomex BBQ HT Gasket Smoker Seal, self Stick Grey Roll 1/2 in 1/8 in Not printed Nomex Not printed
Smoker Chef XXL 20 FT Grill Gasket for Smokers Roll, 2-pack 1/2 in 1/8 in 20 ft (2 x 10 ft) Nomex Not printed
Onlyfire BBQ High Heat Gasket Replacement with Adhesive, Alto Calore Roll Not printed Not printed Not printed Adhesive gasket, fibre not printed Not printed
GriAddict 2-Pack x 10 Feet Grill Seal Gasket MT02 Roll, 2-pack 1/2 in 1/4 in 20 ft (2 x 10 ft) Felt Not printed

Read across the table and the pattern is clear. The universal rolls compete on printed dimensions: width, thickness, and total length are stated in the product name itself. The fitted kits compete on fit instead, naming the cooker sizes they serve and leaving strip dimensions off the page. Neither approach is wrong, but they ask different things of the buyer. A roll buyer measures the cooker. A kit buyer matches a model number.

Adhesive is the column the table leaves out, because it splits the six into two camps rather than six variations. Five products rely on a self-stick or self-adhesive backing that the owner peels and presses into place. One, the kettle kit, relies on RTV adhesive supplied in the box. The difference shows up at install time: a backing film needs a clean, degreased rim and steady pressure as it goes on, while an RTV bead needs the gasket set into it and the lid closed onto the seal while the compound takes hold.

The six products in detail

Each product below is described only with what its opened page prints: the name as listed, the dimensions and materials the page states, the adhesive method, and the cookers the page names as a fit. Pages that leave a figure out are noted as leaving it out.

Weber Kettle GASKET kit 22.5 26.75 LavaLock® Brand

The kettle kit is sold on the maker store run by Island Outdoor, LLC, the company behind the LavaLock gasket line, and the page lists the kit under the SKU KETT-G with stock shown. It is the only product in this guide built around RTV adhesive rather than a peel-and-stick backing.

The maker page states the kit contents plainly: it includes RTV adhesive and gasket, and it installs on the lid side of the kettle. The fit is given by kettle size in the product name, 22.5 and 26.75, which covers the two common kettle diameters from that maker. Because the adhesive is a separate RTV compound rather than a backing film, the owner spreads the adhesive, sets the gasket into it, and closes the lid onto the seal.

The page prints no strip width, no thickness, no roll length, and no temperature figure for this kit. Owners who want a printed temperature rating will not find one here. What the kit offers instead is a matched pair of gasket and adhesive sized for one cooker family, which removes the measuring and cutting that the universal rolls require.

Big Green Egg High-Performance Gasket Kit 113726

This is the cooker maker’s own replacement gasket. The maker page describes a self-adhesive felt roll that restores the seal between the base and the dome of a ceramic kamado, and the listing page for the kit showed it in stock at the time the page was opened for this guide.

The kit is coded by grill size. Code 113726, the kit covered here, serves the 2XL, XLarge, and Large sizes, while a second code, 113733, serves the Medium and MiniMax sizes. The maker page adds one detail that matters at order time: the 2XL size requires two gasket kits to complete the seal, so the largest grill in the range needs a pair of kits rather than one. The listing describes the material as a high-performance felt with a self-adhesive backing, applied by peeling the backing and pressing the strip around the rim.

This kit carries the only printed temperature figure in the guide. The listing states that the gasket withstands extreme heat up to 625 degrees Fahrenheit, or 330 degrees Celsius. No width, thickness, or roll length is printed on either the maker page or the listing page, because the kit is sold by grill size instead of by strip dimensions.

LavaLock 1/2″ x 1/8″ High Temp Nomex BBQ HT Gasket Smoker Seal, self Stick Grey

The grey LavaLock roll is the narrow Nomex option in this guide. Its listing title prints the strip dimensions directly: half an inch wide and one eighth of an inch thick, in a grey finish, with a self-stick backing, and the model code GL-1/2 is recorded in the maker’s own listing data for the same product.

Nomex is the material named in the title, which separates this roll from the felt rolls in the guide. The self-stick backing means the install follows the peel-and-press pattern: the old gasket comes off, the rim is cleaned, and the strip is pressed around the edge of the lid or the body. The listing page opened for this guide showed a small number of units left in stock, so its sale status is worth a fresh check on the listing page at order time.

Colour is a printed difference inside this guide. This roll is grey, while the Smoker Chef roll, the Onlyfire roll, and the GriAddict felt are all listed in black. Colour changes nothing about the seal itself, but it decides how visible the strip is against a dark lid rim, and the grey finish is part of how this listing names and separates the product from other rolls.

The opened page does not print a roll length or a temperature figure for this product, even though the title calls it high temp. That wording is a material description on the page, not a rating, and this guide leaves it as a description. An owner who needs a stated length or a stated temperature number should confirm both on the listing page before relying on either.

Smoker Chef XXL 20 FT Grill Gasket for Smokers

The Smoker Chef entry is a two-roll pack of black Nomex tape. The listing states the size directly: 20 feet in total, supplied as two rolls of 10 feet, half an inch wide and one eighth of an inch thick, with a self-adhesive backing, and the listing reported more than 300 units bought in the past month when the page was opened.

The listing prints the fullest install sequence in this guide. The owner scrapes off the old gasket with a razor, cleans and degreases the surface so the adhesive sticks, peels the white backing away as the strip is applied, presses the gasket around the edge of the grill and its lid, cuts the excess length, and then closes the lid and waits at least 12 hours for better fixation. That 12 hour wait is the only cure time printed on any page in this guide.

Compatibility is printed as a brand list: the listing names Masterbuilt, Weber, Traeger, Char-Griller charcoal grills, kettle charcoal grills, Oklahoma Joe, and Camp Chef pellet smokers as suitable. The page prints no temperature figure, describing the Nomex only as a high heat temperature material, so the rating column for this roll stays blank in the table above.

Onlyfire BBQ High Heat Gasket Replacement with Adhesive, Alto Calore

The Onlyfire entry is an adhesive gasket roll aimed at kamado cookers. The listing names the fit in its title: Big Green Egg, Kamado Joe, and Vision Grills. The page showed the roll in stock, sold through the maker’s own storefront, with more than 50 units bought in the past month at the time the page was opened.

The product details on the page give the brand as onlyfire, the model name as Alto Calore, and the colour as black, with the size option labelled Kamado Smokers. That makes this roll the aftermarket counterpart to the Big Green Egg kit above: both serve ceramic kamado rims, one as the cooker maker’s own coded kit and this one as a general kamado roll from an accessories maker.

The opened page does not print a strip width, a thickness, a roll length, or a temperature figure, and it does not name the gasket fibre. Kamado owners considering this roll should compare their rim circumference and rim width against the size information on the listing page, because the page itself leaves those numbers to the size selector rather than the description.

GriAddict 2-Pack x 10 Feet Grill Seal Gasket MT02

The GriAddict pack is the thick felt option. The listing gives the model number MT02 and prints the dimensions in the title: two rolls of 10 feet for a 20 foot total, half an inch wide and a quarter inch thick, in black felt. The listing reported more than 50 units bought in the past month when the page was opened.

The quarter inch thickness is the point of difference. Every other roll in this guide that prints a thickness sits at one eighth of an inch, so the GriAddict felt carries twice the material to compress. That suits lids with a wider or uneven gap, including older offset and pellet cookers whose factory seals have flattened. The listing prints its compatibility as Oklahoma Joe, Weber, Pitboss, and pellet grills, which matches that offset and pellet focus.

The page prints no temperature figure for the felt, describing it only as a high-temp seal material. As with the other rolls, the wording is a description rather than a rating. Owners comparing this pack against the Nomex rolls are choosing between a thicker felt strip and a thinner Nomex strip at the same half inch width and the same 20 foot total length.

Buying guide: matching heat sealing tape for smokers to your cooker

Start from the cooker, not from the roll. Kettle owners have a kit cut for their lid sizes. Kamado owners choose between the cooker maker’s coded kit and a general kamado roll. Offset, pellet, and drum owners are served by the universal rolls, whose pages print the dimensions that fitted kits leave out.

Measure the rim before ordering any universal roll. The circumference of the lid rim decides how much tape one seal takes, and the rim width decides whether a half inch strip covers the mating surface. The two 20 foot packs in this guide give enough length for a lid and a body rim on most cookers, with the second roll left over for the next replacement. Where a page prints no length, as the LavaLock grey roll and the Onlyfire roll do not, the measurement matters even more, because the listing page is the only place to confirm how much tape is in the pack.

Read the temperature line literally. One page in this guide prints a figure, 625 degrees Fahrenheit on the Big Green Egg kit listing, and five print none. A page that says high temp without a number is describing the material family, not certifying a limit. If a cooker regularly runs hotter than the range a maker states, the honest answer from these pages is that most of them do not state a range at all, and the maker page or the listing page is where that figure has to be confirmed before the tape goes on.

Felt and Nomex divide the guide by cooker type as much as by material. Felt is the factory-style material: the Big Green Egg kit is felt and the GriAddict pack is felt, and both are aimed at rims that left the factory with a felt seal or a seal of similar build. The two Nomex rolls are universal strips sold by width and thickness for owners who measure and cut their own. Neither material carries a printed temperature figure on the universal roll pages opened here, so the choice between them rests on fit and thickness rather than on a rating those pages do not state.

Plan the install around the adhesive. Self-stick rolls need a rim that has been scraped clean and degreased, following the sequence the Smoker Chef listing prints, and that same listing asks for at least 12 hours with the lid closed before the cooker is used again. The kettle kit replaces backing film with RTV adhesive included in the box and goes on the lid side. Kamado owners with the largest grill in the Big Green Egg range should also note the maker page detail that the 2XL takes two kits, not one.

Finally, match thickness to the gap. A lid that closes evenly on a sound rim takes a one eighth inch strip. A lid with a visible gap, a warped edge, or a factory gasket worn flat takes the quarter inch felt. Buying the thicker strip for a tight lid makes the lid sit high; buying the thinner strip for a wide gap leaves the leak in place. The tape can only seal the gap it can fill.

Six products cover the main smoker families: a kettle kit with RTV adhesive, a kamado kit with the guide’s only printed temperature figure, two Nomex rolls, a kamado roll, and a thick felt pack. Choose by cooker first, then by width and thickness, then by roll length, and check the listing page for any figure the pages here leave blank.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.