Updated Nov 16, 2026· 14 min read

Key takeaways

  • Compare five blower kits for offset smokers with printed CFM figures, adapter fit notes, damper control and probe details drawn from maker pages for buyers.

A blower kit for offset smokers joins a fan to an adapter plate so a controller can push measured air into the firebox instead of leaving airflow to manual vent work. This guide compares five kits on printed airflow figures, adapter fit, damper design and box contents, using only details published on maker pages.

How a blower kit for offset smokers works

An offset smoker burns its fire in a side firebox, and heat reaches the cooking chamber only when air moves through that box in a steady stream. A blower kit mounts a small fan at the firebox intake, and a controller reads pit temperature from a probe and speeds up or slows down the fan to hold the set point.

Without a fan, the cook adjusts the intake vent by hand every time the fire cools or flares, and each adjustment takes minutes to show up at the grate. With a fan kit fitted, the controller makes those small corrections on its own, opening the airflow when the pit temperature dips and easing off when the fire runs hot.

The kit part of the product matters as much as the fan itself. A complete kit pairs the fan with an adapter that matches the intake shape on the cooker, plus the damper or mounting hardware that seals the joint. A fan with strong airflow figures still performs poorly when its adapter leaks air around the edges of the vent opening.

Offset smokers place one specific demand on these kits: the firebox intake on many offset models is a round vent or a sliding door on the firebox end, so the adapter has to grip that opening and stay sealed while the firebox wall gets hot. The five kits below were checked against the fit notes and airflow figures printed on their maker pages.

What to check before buying a blower kit for offset smokers

Four checks decide whether a kit suits an offset cooker: the airflow figure the maker prints, the adapter style and the vent shapes it covers, the damper design that meters air between fan cycles, and the controller the fan needs in order to run. Each of the five kits below answers those checks in a different way.

Airflow figures and why they differ

Fan output is printed in cubic feet per minute, written as CFM, and the five makers here do not all publish the figure in the same place. Flame Boss prints 12 CFM for its integrated blower, FireBoard prints 20 CFM for its Drive Blower, MeatStick prints up to 15 CFM, and BBQ Guru prints 10 CFM and 25 CFM for its two fan sizes.

ThermoWorks does not print a CFM figure on the Billows product page at all, so this guide lists that field as not printed rather than estimating it. A higher CFM figure is not automatically better for a small firebox, because an oversized fan can overshoot the set temperature on a compact offset; the damper and the controller logic share the work of keeping swings small.

Adapters, dampers and mounting

Adapter design decides how much fitting work a kit needs. Spring-loaded nozzles expand into standard draft vents, flat plates bolt or clip over the lower vent, and brand-specific mounts exist for large kamado cookers. For an offset firebox, the fit notes that matter are the ones naming offset or barrel cookers, or round firebox vent holes.

Dampers matter because a fan that stops still leaves an open hole in the firebox wall. A damper disc or an adjustable damper closes that hole down between fan cycles, so the fire gets only the air the controller intends. Two of the kits below build damper control into the fan unit, and one includes a separate damper with sixteen adjustment stops in the kit line.

Blower kit for offset smokers: the five verified kits

Each kit below was verified on an opened maker or seller page that lists it for sale, and every figure in its section comes from that page. The sections follow the same order each time: what the kit contains, the airflow figure the maker prints, how it mounts, and what else the buyer needs before the first cook.

ThermoWorks Billows BBQ Temperature Control Fan Kit (with Damper)

The Billows kit from ThermoWorks, sold under the part number TW-1600-KIT, pairs the Billows fan with a damper in the same box. The maker page lists an expandable, spring-loaded nozzle that fits many standard draft vents, a 12V AC power adapter in the box, and a note that the fan carries no internal batteries.

Because the fan holds no battery of its own, it draws external 12V power while it runs, and it only works when paired with a compatible ThermoWorks controller. The maker names Signals, Smoke X, RFX Gateway and ThermaQ 2 as the controllers that can drive it, so a buyer who already owns one of those units adds only the fan kit to start cooking with forced air.

The damper in this kit gives the cook a manual way to trim airflow at the intake. For owners of an extra-large Big Green Egg, the maker sells a separate Billows Kamado Mounting Kit, which signals that the standard nozzle covers standard draft vents while the largest kamado intake needs its own mount. The maker page prints no CFM figure for the Billows fan.

That missing figure is worth pausing on, because it changes how this kit is compared. The other four kits can be lined up by their printed CFM numbers; the Billows has to be judged on its fit system, its damper and its controller pairing instead. ThermoWorks sells it as an add-on for owners already inside its thermometer line, and the page’s contents list reads the same way.

  • Kit contents: Billows fan with damper, 12V AC power adapter
  • Printed airflow: not printed on the maker page
  • Mounting: expandable spring-loaded nozzle for standard draft vents
  • Controller needed: Signals, Smoke X, RFX Gateway or ThermaQ 2
  • Power: external 12V supply; no internal batteries

BBQ Guru DigiQ DX3 temperature control kit

The DigiQ DX3 from BBQ Guru is a controller kit that the maker sells with a choice of fan or with no fan at all. The maker page states that the control holds pit temperatures from 32 degrees F to 475 degrees F with accuracy of plus or minus 2 degrees F, and that the box includes one 6 ft food probe and one 6 ft pit probe.

Fan choice is the centre of this kit. The maker offers the Pit Viper fan and the Pit Bull fan as kit options, and its support page prints the Pit Viper at 10 CFM and the Pit Bull at 25 CFM, with aluminium nozzles, heat dissipaters and adjustable dampers on both fans. The same page states that the control can power up to two fans through the Fan Splitter cord, and that each fan cord runs 6 ft.

The control box is aluminium, runs on 100 to 240V AC, and comes in black or green. Probe cables can be ordered in 4 ft, 6 ft or 8 ft lengths. The maker lists a SMART COOK feature with variable fan flow rate, a Ramp Mode and Open Lid Detection among the control’s functions, which is the part of the kit that decides how gently the fan feeds the fire.

The printed temperature range frames what this kit can run: 32 degrees F at the bottom covers cold-weather holding, and 475 degrees F at the top runs well past the band where offset smokers cook, with the plus-or-minus-2-degree accuracy figure printed beside it. A buyer comparing controllers should note that BBQ Guru prints both ends of that range and the accuracy figure on the product page itself, where some makers print only a top temperature.

  • Kit contents: DigiQ DX3 control, 6 ft food probe, 6 ft pit probe, fan option
  • Printed airflow: Pit Viper 10 CFM; Pit Bull 25 CFM
  • Temperature range: 32 to 475 degrees F, plus or minus 2 degrees F
  • Mounting: fan nozzle with adjustable damper
  • Power: 100 to 240V AC

FireBoard Drive Blower G3

The Drive Blower G3 from FireBoard Labs is a fan unit rated at 20 CFM on the maker’s own pages, with variable speed that the user can set as a manual percentage or leave to a compatible FireBoard controller running its own control logic. The blower ships with two adapter plates and mounts at the grill’s lower air vent.

The maker’s fitting notes say the blower installs directly to the lower air vent with no permanent modifications to the cooker, which suits owners who do not want to drill a firebox. A seller page for the unit states that it works with the FireBoard 2 Drive and the FireBoard 2 Pro, and that a G3 ball-valve adapter and a blower nozzle adapter are also listed for the line.

Power comes from the FireBoard unit’s own battery rather than a wall outlet. The maker states that a charged FireBoard battery runs the blower for about 10 to 12 hours of cooking, which covers most overnight offset sessions without a cord crossing the patio. The fan itself carries no separate battery figure on the pages opened for this guide.

  • Kit contents: Drive Blower G3 fan, two adapter plates
  • Printed airflow: 20 CFM, variable speed
  • Mounting: lower air vent, no permanent modifications per maker
  • Controller needed: FireBoard 2 Drive or FireBoard 2 Pro
  • Power: FireBoard battery, about 10 to 12 hours per maker

MeatStick Blow automatic fan

The Blow from MeatStick is a variable-speed fan that the maker’s launch release rates at up to 15 CFM. Its fit guide describes a spring-clip mount built from a three-leg clip and a face gasket, two stainless kamado plates in the box, and an intake damper disc that the user turns to trim airflow at the vent.

Offset owners get a direct mention in that fit guide: on a Char-Griller offset, the fan clips into one of the round vent holes on the firebox, with no drilling. Kettle, bullet and drum cookers mount through an existing opening or through a single 1 and one-quarter inch hole, and the two kamado plates measure about 3 and a half by 3 inches and about 3 and one-eighth by 2 and three-quarter inches.

The box includes a hub-link cable of 1.5 m, a USB-C to USB-A cable of 1.5 m and high-temperature foil tape, but no charger: the fan needs a USB charger or power bank rated 5V/2A or higher. The fan alone also needs the maker’s Forge Hub and a Wired Ambient Probe, both included in every V Forge Set, and the hub runs about 14 hours on its battery.

The maker’s launch release adds two hardware notes the fit guide does not repeat: the Wired Ambient Probe that reads the pit air is rated from -4 degrees F to 716 degrees F, and the fan’s motor is a brushless centrifugal unit on dual ball bearings. The same release states the fan went on sale through the maker’s own store at launch, which matches the fit guide’s place in the maker’s current line.

  • Kit contents: Blow fan, two stainless kamado plates, damper disc, cables, foil tape
  • Printed airflow: up to 15 CFM, variable speed
  • Mounting: spring clip; clips into a round firebox vent hole on Char-Griller offset models
  • Controller needed: V Forge WiFi Hub and Wired Ambient Probe
  • Power: USB charger or power bank, 5V/2A or higher, not included

Flame Boss 400-WiFi Universal Smoker Controller Kit

The Flame Boss 400-WiFi Universal kit builds its blower into the controller, and the maker prints the integrated blower at 12 CFM. The kit box holds the WiFi controller with its blower, one high-temperature meat probe, one high-temperature pit probe and a power supply, and the maker covers all parts with a 2-year warranty.

Fit is where this kit speaks directly to offset owners. The maker’s printed compatibility list for the Universal kit names drum, barrel, cabinet, gravity-fed and offset style charcoal grills and smokers, and it names Char-Griller offset and barrel models among the fits. That printed list is the strongest offset-specific fit statement among the five kits in this guide.

The maker describes patented software driving the variable-speed blower, and lists voice-assistant control among the kit’s functions. One limit is printed plainly: this model does not support a Y-cable, so it cannot run extra meat probes beyond the single meat probe in the box. Cooks who monitor several cuts at once should weigh that limit before choosing it.

That single-probe limit cuts differently on an offset than on a kamado. An offset cook often runs one large cut, a brisket or a shoulder, for most of a session, and the pit probe in the box watches the chamber the whole time. The limit bites when the cook adds a second and third cut at different thicknesses, which is why the maker prints it in the kit description rather than in fine print.

  • Kit contents: WiFi controller with integrated blower, meat probe, pit probe, power supply
  • Printed airflow: 12 CFM integrated blower
  • Mounting: Universal kit adapters for offset, drum, barrel, cabinet and gravity-fed cookers
  • Controller needed: none; controller is built into the kit
  • Warranty: 2 years on all parts, per maker

Side-by-side comparison

The table gathers the printed figures from the five maker pages into one view. Airflow is listed exactly as each maker prints it, the adapter column repeats each kit’s fit wording in short form, and the controller column shows what else must be on hand before the fan can run a cook.

Kit Printed airflow Adapter and fit Controller needed
ThermoWorks Billows Kit (with Damper) Not printed Spring-loaded nozzle, standard draft vents Signals, Smoke X, RFX Gateway or ThermaQ 2
BBQ Guru DigiQ DX3 kit 10 CFM or 25 CFM fan options Fan nozzle with adjustable damper Built in (DigiQ DX3 control)
FireBoard Drive Blower G3 20 CFM Two adapter plates, lower air vent FireBoard 2 Drive or FireBoard 2 Pro
MeatStick Blow Up to 15 CFM Spring clip, plates, round vent hole fit V Forge WiFi Hub with Wired Ambient Probe
Flame Boss 400-WiFi Universal 12 CFM Universal adapters, offset styles listed Built in

Read the airflow column with the firebox size in mind. A compact offset firebox reaches its set point quickly, and a 25 CFM fan on full blast can overshoot that set point before the controller eases off, while a large trailer offset moves far more air and can use the bigger figure. The damper column matters on windy days, when a still fan with an open intake still feeds the fire.

Setup notes printed on the maker pages

Cable runs decide where the controller can sit. BBQ Guru prints a 6 ft fan cord and probe cables in 4 ft, 6 ft and 8 ft lengths, while MeatStick prints 1.5 m hub-link and USB cables in the Blow box. On a wide offset rig, those printed lengths set how far the control unit can sit from the firebox heat.

Power planning splits the group three ways. The Billows kit draws from its included 12V AC adapter and the DigiQ DX3 runs on 100 to 240V AC, so both want an outlet within cord reach. The FireBoard pairing runs off the controller’s battery for about 10 to 12 hours per the maker, and the MeatStick hub runs about 14 hours, though its fan still needs a USB charger or power bank rated 5V/2A or higher at the cooker.

Large offsets with two intake points have one printed route here: the DigiQ control can power up to two fans through the Fan Splitter cord, per the maker’s support page. The other kits describe single-fan setups, and the Flame Boss 400 prints its own ceiling in the other direction, one meat probe and no Y-cable, so a two-firebox rig is served by the Guru kit’s fan count rather than by probe count.

Mounting hardware is the last setup note. The Billows nozzle expands into standard draft vents, with a separate mounting kit printed for the extra-large Big Green Egg. The FireBoard blower’s two plates fit the lower air vent with no permanent modifications. The MeatStick plates cover kamado intakes at two printed sizes, and its clip covers the round vent holes on a named offset brand’s firebox.

Buying guide: matching a kit to your offset cooker

Start with the intake on your own firebox. Measure the vent shape before ordering anything: round vent holes suit the MeatStick clip mount, a lower vent slot suits the FireBoard plates, and the Flame Boss Universal list and the Billows spring nozzle cover the broad middle ground of standard draft openings.

Next, count what you already own. A Signals or Smoke X owner adds the Billows kit and nothing else. A FireBoard 2 Drive owner adds the G3 blower and runs it from the same battery. A cook starting from zero needs a kit with the controller built in, which is the DigiQ DX3 kit or the Flame Boss 400, or a full V Forge Set for the MeatStick fan.

Then weigh the probe count. The DigiQ DX3 ships with one food probe and can run two fans at once, which suits a large offset with two intake points. The Flame Boss 400 prints its single-meat-probe limit in plain text. The Billows and G3 inherit their probe counts from the controller they attach to, so check that controller’s page before ordering.

Power runs last. Corded kits like the DigiQ DX3 need an outlet near the cooker. Battery-driven setups like the FireBoard pairing free the cooker from the wall for about 10 to 12 hours per the maker, and the MeatStick hub stretches to about 14 hours, while the fan itself still needs a USB power source on hand.

Conclusion

For offset cooking, the Flame Boss 400-WiFi Universal kit prints the clearest fit list, the FireBoard Drive Blower G3 prints the highest single airflow figure at 20 CFM, and the MeatStick Blow prints a no-drilling fit for a named offset brand. Match the adapter to your firebox vent first, then compare the printed figures.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.