Updated Nov 16, 2026· 14 min read

Key takeaways

  • Five full starter kits compared on printed battery format, output range, tank size and box contents, from a 3200mAh MTL kit to a 200W dual-battery kit in full.

A vape starter kit for smokers is a boxed kit with a device, a tank or pod and at least one coil, ready to pair with bottled liquid. The five kits here are compared on printed figures: battery format, output range, tank capacity, the coils in the box and box contents. They run from a mouth-to-lung kit to a 200W box kit, and the entries say so.

Quick verdict

The Zelos 3 is the only mouth-to-lung led kit here, with a built-in 3200mAh battery and two coils at opposite ends of the range. The Coolfire Z80 NEX and Vinci Spark 100 run on a single 18650 bought separately. The Aegis Legend 3 needs two 18650 cells for 200W, and the Armour Ultra builds a 5500mAh battery into a 100W body.

Product Type Best for Key printed spec Main limit
Aspire Zelos 3 Kit MTL and RDL tank kit A built-in battery and two coil styles 3200mAh built in; 1-80W; Nautilus 3 Tank 4mL Output ceiling is the smallest here
Innokin Coolfire Z80 NEX Mod Kit Single-battery tank kit A 5ml tank and a wide coil family Single 18650, not included; 6-80W; Zenith Nex Tank 5ml Battery bought separately
VooPoo Vinci Spark 100 Vape Kit Single-battery tank kit 100W with smart modes Single 18650, sold separately; 5-100W; 2ml tank Smallest tank in the group
Geek Vape Aegis Legend 3 200W Starter Kit Dual-battery box kit The highest printed output Dual 18650, sold separately; 5-200W; Z FLI Tank 5.5mL Two cells to buy and charge
Vaporesso Armour Ultra Kit Built-in battery box kit The largest built-in battery 5500mAh built in; 5-100W; iTank T 6ml Battery cannot be swapped when it ages

The first decision inside this keyword is not brand or power; it is battery format. Two kits carry their battery inside the body, and three need 18650 cells that are not in the box. That single printed fact changes what a reader must buy alongside the kit, so it leads every entry below.

How we selected

Each kit was taken from an opened maker or listing page, and every figure in this guide is copied from one of those pages as printed. Battery format and capacity, output range, tank capacity, coil resistances and their printed wattage bands, charging details and box contents are recorded kit by kit, and a figure a page did not print is left out.

A kit counted as a starter kit here if its box prints a complete working set: device, tank or pod, and at least one coil, with a charging cable in most cases. Mods sold without a tank were not counted, and neither were pod pens, which have their own guides in this project. What is not in the box, above all batteries, is stated in each entry.

The five kits were also chosen to sit apart from the project’s earlier kit lists. None of them repeats a pick from the mouth-to-lung starting kit list or the sub-ohm kit list, and the two battery formats and three output classes give this keyword its own ground to cover rather than a re-run of an earlier selection.

Five vape starter kit for smokers picks, from MTL to 200W

The entries run in output order, from the 80W mouth-to-lung kit to the 200W dual-battery kit. Each states who the kit suits, the printed figures behind it, its limits, and the clearest buy-if and skip-if cases, including exactly what the box does and does not contain.

Aspire Zelos 3 Kit

The Zelos 3 is the starter-shaped entry in this group: a built-in 3200mAh battery, an output range of 1W to 80W, and a Nautilus 3 Tank that the page pairs with both mouth-to-lung and restricted direct-lung coils. Its maker page states it caters to beginners and experienced vapers, and the printed mode list backs the flexible reading.

The modes are printed as VW, VV, TC across nickel, titanium and stainless steel, TCR, CPS and Bypass, run by an ASP chipset and shown on a 0.96 inch TFT color screen. The body is zinc alloy. Charging is Type-C at 2A, and the page’s question section states a full charge takes approximately 1.5 hours, with the battery providing up to 2 days of moderate use as printed.

The tank holds 4mL with a sliding top-fill system. Two coils are included: a 1.8 ohm BVC coil printed at 10 to 14W for mouth-to-lung use, and a 0.7 ohm mesh coil printed at 20 to 25W for restricted direct-lung use. The airflow ring has seven inlet holes printed from 0.8 to 3mm, both MTL and RDL drip tips are covered, and the page prints liquid guidance for each coil: 50/50 style liquids with the 1.8 ohm coil and 70VG/30PG with the 0.7 ohm coil.

  • Pros: built-in battery, nothing extra to buy for power; two coils covering MTL and RDL; printed liquid guidance per coil; 510 connection for other tanks.
  • Cons: 80W ceiling is the smallest here; battery is fixed inside the body; modes list is long for a first kit.
  • Buy if: you want one kit that starts mouth-to-lung and can loosen up later.
  • Skip if: you want swappable batteries or output above 80W.

Innokin Coolfire Z80 NEX Mod Kit

The Coolfire Z80 NEX kit pairs an 80W-class mod with the largest mid-group tank: the Zenith Nex at 5ml with a top-fill design. It runs on a single 18650 battery that is not included, which is the first printed fact a buyer needs, and its output range is printed as 6W to 80W across mouth-to-lung and restricted direct-lung styles.

The mod’s printed dimensions are 58.33 by 27.56 by 134.82mm, and its materials are listed as zinc alloy, PCTG and leather. The tank takes the full Z Coil family; the box fits a Z Coil 0.8 ohm with an MTL drip tip pre-installed and adds a spare Z Coil 0.3 ohm with an RDL drip tip, plus a spare 5ml glass tube, an O-ring set, a Type-C cable and a quick start guide.

The page also prints a standard 510 connection, so other tanks can be fitted to the mod. Coil choice is the deep bench here: the compatibility list runs from the included pair through 1.6 ohm, 1.2 ohm and 0.48 ohm Z Coils, which gives this kit the widest printed coil family of the five.

  • Pros: 5ml top-fill tank; two coils and two drip tips in the box; spare glass included; widest printed coil family here.
  • Cons: 18650 battery not included; output matches the Zelos 3 ceiling; leather finish will not suit every reader.
  • Buy if: tank size and coil choice matter more than a built-in battery.
  • Skip if: you want to open the box and vape without buying a cell first.

VooPoo Vinci Spark 100 Vape Kit

The Vinci Spark 100 is the design-led single-battery kit: an aluminium alloy body with a starlight panel display of 144 LED lights and three animation themes printed on its page. Under the panel it is a 5W to 100W kit running on a single 18650 battery sold separately, driven by a GENE.AI 2.0 chipset.

The chipset modes are printed as Smart Mode, which adjusts power to the coil, ECO Mode for conserving battery, and RBA Mode for manual settings. A 0.96 inch TFT screen carries the information, airflow is adjustable, and charging is over Type-C. The page lists its protection set by name: overtime, overheating, short-circuit, output over-current, low battery, anti-reverse battery and overcharge protection.

The tank is the Uforce-X Nano at 2ml, the smallest in this group, with a top filling design and adjustable top airflow. Two PnP X coils are in the box, at 0.3 ohm and 0.6 ohm, with a spare 2ml glass container and a silicon rubber pack. The printed tank styles cover direct-lung, restricted direct-lung and mouth-to-lung vaping.

  • Pros: 100W from one cell; smart mode sets power by coil; two coils in the box; compact tank with top airflow.
  • Cons: battery sold separately; 2ml tank is the smallest here; LED panel is decoration some readers will not want.
  • Buy if: you want single-battery 100W output with automatic power setting.
  • Skip if: tank capacity matters, or you dislike light displays on hardware.

Geek Vape Aegis Legend 3 200W Starter Kit

The Aegis Legend 3 carries the word starter in its printed product name and the highest figures in the group: dual 18650 batteries, sold separately, an AS Chip 4.0, and an output range of 5W to 200W. Its page lists an IP68 rating for resistance to water, dust and shocks, which is the durability line this kit is sold on.

Modes are printed as Power, TC, TCR, ECO, Boosting and Bypass, shown on a 0.96 inch TFT color screen, with USB Type-C charging and an A-Lock switch that the page describes as preventing accidental firing. The included Z FLI Sub-Ohm Tank holds 5.5mL with a flip-top fill system and adjustable top airflow.

Two Z XM coils are in the box: a 0.15 ohm coil printed at 70 to 85W and a 0.4 ohm coil printed at 50 to 60W, with a spare parts pack, a Type-C cable and a manual. The page prints its liquid guidance as freebase e-liquids at a 70VG/30PG ratio for this tank and coil set. Ten colors are listed, from Black and Dark Gray to Golden Blue and Rainbow.

  • Pros: highest printed output at 200W; IP68 rating printed; 5.5mL flip-top tank; six printed modes.
  • Cons: two 18650 cells to buy before first use; largest commitment in the group; coils printed for higher wattage bands only.
  • Buy if: you want the power ceiling and the printed durability rating.
  • Skip if: you want a kit that works out of the box with nothing added.

Vaporesso Armour Ultra Kit

The Armour Ultra takes the opposite battery route from the Legend 3: a built-in 5500mAh battery that the maker page describes as providing battery life close to that of two 18650 batteries while keeping a built-in design. Output is printed at 5W to 100W, and the page states one charge keeps the kit going for up to 3 days in its own figures.

The printed dimensions are 144.5 by 37.6 by 31mm and the weight is 256g. A 0.96 inch TFT screen is fitted, charging is Type-C at DC 9V/2A or 5V/3A, and the modes are printed as Boost, Pulse, Eco and temperature control. The maker page lists IP68 and IP69K certification and a MIL-STD-810H 1.2 meter drop test for the mod, with a note that the certifications apply to the mod only.

The iTank T holds 6ml, the largest tank here, with a sliding top fill and top airflow. Two GTi Dual Mesh coils are included, a 0.2 ohm coil printed at 60 to 75W pre-installed and a 0.4 ohm coil printed at 50 to 60W in the box, and the page states GTi coils from 0.15 ohm to 0.5 ohm fit. Seven colors are printed, including Titanium Silver, Dune Gold and Obsidian Black.

  • Pros: largest built-in battery and largest tank; fast printed charging rates; no separate cells to buy; printed durability certifications for the mod.
  • Cons: built-in battery cannot be replaced; 256g is the heaviest printed weight; coils sit in higher wattage bands.
  • Buy if: you want dual-cell endurance without handling loose batteries.
  • Skip if: you prefer to swap cells, or you vape at low wattage.

Buying guide

The five kits divide on four printed questions: where the battery lives, how much output the box offers, how much liquid the tank holds, and which coils the box starts with. The points below take those questions in order, using only the figures printed for the kits above.

Battery format: built in or bought separately

Two kits print a built-in battery: the Zelos 3 at 3200mAh and the Armour Ultra at 5500mAh. Three print an empty battery bay: the Coolfire Z80 NEX and Vinci Spark 100 take one 18650 each, and the Aegis Legend 3 takes two, with every page stating plainly that the cells are not included or are sold separately.

Neither format is presented as the right one. A built-in battery makes the box complete on day one and fixes the kit’s life to that cell, while loose cells add an extra purchase and a charger decision but can be replaced when they age. The printed fact to settle first is simply which side of that line your kit sits on.

What a vape starter kit for smokers should print in the box

A complete box, as printed across these five, holds the device, the tank, at least one coil and usually a charging cable. The fuller boxes add more: the Coolfire kit adds a spare glass tube and O-rings, the Vinci Spark 100 adds a spare glass container, and the Aegis Legend 3 adds a spare parts pack. Two coils are printed in every box in this group.

The gaps are as printed as the contents. No box here includes e-liquid, and three boxes exclude the batteries their devices need. A reader adding up a first purchase should list those two absences beside the kit itself, because both are stated on the pages and neither is a detail to discover at the door.

Output range against the coils in the box

Printed output runs from 1W to 80W on the Zelos 3 to 5W to 200W on the Aegis Legend 3, but the boxed coils narrow the working band. The Zelos 3 coils are printed at 10 to 14W and 20 to 25W, the Legend 3 coils at 50 to 60W and 70 to 85W, and the Armour Ultra coils at 50 to 60W and 60 to 75W, so the box, not the ceiling, sets the starting band.

The Vinci Spark 100 answers the matching problem with its Smart Mode, which the page describes as adjusting power to the fitted coil automatically. Readers who do not want to set wattage by hand have that printed option in one kit here, while the other four expect the setting to be chosen from the coil’s printed band.

Tank capacity and fill design

Printed tank capacities run from 2ml on the Vinci Spark 100 to 6ml on the Armour Ultra, with the Zelos 3 at 4mL, the Coolfire kit at 5ml and the Aegis Legend 3 at 5.5mL. All five fill from the top, by sliding, flipping or opening designs as printed, so the comparison is capacity and mechanism rather than fill position.

Capacity interacts with the coil bands above. A 2ml tank over a 0.3 ohm coil empties faster than a 6ml tank over the same resistance, and the printed figures let a reader pair them honestly: the smallest tank here sits on the kit with the joint-smallest coil band, and the largest tank sits on a kit whose coils start at 50W.

Spare glass is the quiet detail in three boxes: the Coolfire kit prints a spare 5ml glass tube, the Vinci Spark 100 prints a spare glass container, and the Zelos 3 box prints a spare glass tube as well. A cracked tank glass is the most common way a kit leaves service, so the presence or absence of a printed spare is a practical line to compare beside capacity.

FAQ

The questions below are the ones a first kit purchase raises most often, and each answer is built from the printed pages behind the five entries. Where a page does not print an answer, the reply says so, and no figure in this section comes from anywhere else.

Does a vape starter kit for smokers include batteries?

It depends on the kit, and every page here prints the answer. The Zelos 3 and Armour Ultra include their batteries inside the body, at 3200mAh and 5500mAh. The Coolfire Z80 NEX, Vinci Spark 100 and Aegis Legend 3 do not: their pages state the 18650 cells are not included or are sold separately, one cell for the first two, two for the Legend 3.

That makes the battery line the most important line in any kit listing. A kit whose box excludes its cells is not ready to use on arrival, however complete the rest of the box looks, and all three pages here say so in plain wording that a reader can check before ordering.

Which of these kits suits a mouth-to-lung start?

On printed figures, the Zelos 3. It is the only kit here whose box includes a coil printed for mouth-to-lung wattage, the 1.8 ohm BVC at 10 to 14W, and the only one whose page prints 50/50 style liquid guidance. The Coolfire kit also fits a 0.8 ohm MTL coil and prints MTL among its styles, with a wider coil family behind it.

The other three kits print their included coils in higher bands: 0.3 and 0.6 ohm on the Vinci Spark 100, and 0.15 to 0.4 ohm sets on the Legend 3 and Armour Ultra. Those are printed as restricted or direct-lung kits, and this guide does not re-label them as mouth-to-lung starters.

How long do the built-in batteries last between charges?

Two pages print duration claims. The Zelos 3 page states up to 2 days of moderate use from its 3200mAh battery, and the Armour Ultra page states one charge keeps the kit going for up to 3 days, with a further figure of 2 to 3 days for moderate direct-lung users. Both are maker figures, printed as claims, and are repeated here as such.

No duration is printed for the three 18650 kits, because the cells are chosen by the buyer. For those kits the comparable printed figures are the cell count and the output range, and any runtime estimate would depend on cells this guide has not verified, so none is offered.

Can the tanks be swapped between these kits?

Two pages print a 510 connection explicitly: the Coolfire Z80 NEX page states the mod suits other 510-threaded tanks, and the Zelos 3 page states its standard 510 connection allows compatibility with most tanks. On those two kits, a tank swap is a printed feature rather than an assumption.

For the other three, the pages print their own tank pairings without a general compatibility statement, so this guide does not claim swaps for them. Coil families are never interchangeable across these kits in any case: Z Coils, PnP X coils, Z XM coils, GTi coils and Nautilus coils are five separate printed families. That separation keeps spare orders simple: one coil family per kit, matched by the exact printed name.

Conclusion

Start with the battery line: built in, choose between the Zelos 3 for a mouth-to-lung start and the Armour Ultra for capacity; bought separately, choose between the Coolfire kit’s coil family, the Vinci Spark 100’s smart modes and the Legend 3’s 200W ceiling. Every figure behind that choice is printed above.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.