Updated Nov 17, 2026· 15 min read

Key takeaways

  • Six hardware picks for building a nightstand, from soft-close drawer slides and hinges to leveling feet and edge banding, with sizes and load ratings checked.

Building a nightstand means choosing hardware that moves smoothly, holds its load and stays square for years, and the wrong slide or hinge shows up the first week. The best hardware to use for making nightstands covers slides, hinges, leveling feet and edge banding, and this guide compares six pieces with their sizes and load ratings checked.

Quick verdict

Start with the Blum TANDEM plus BLUMOTION 563H slide for a hidden, quiet drawer, and pair it with the 110 degree soft-close hinges when the nightstand has a door. Add the side-mount soft-close slides when the budget or the cabinet shape favors visible hardware, then level the base and finish the plywood edges.

Product Type Best for Key spec Pack or kit
Blum TANDEM plus BLUMOTION 563H Undermount drawer slide Hidden, quiet drawers 100 lb static, 9 to 21 in 2 slides, 2 clips, screws
Full overlay cabinet hinges, 110 degree Soft-close hinge Frameless doors 110 degree opening, 3D adjustment 20 hinges, screws
Soft close full extension drawer slides Side-mount drawer slide Full drawer access 100 lb per pair, 12 to 24 in 10 pairs, brackets, screws
Cabinet leveling feet, 80 to 110 mm Leveling foot Low bases on uneven floors 80 to 110 mm, up to 330 lb Packs of 2, 4, 12 or 48
Blum MOVENTO 763H Undermount drawer slide Heavier drawers, push to open 125 lb static, 12 to 21 in Pair, clip sold separately
Preglued birch veneer edge banding Edge banding Birch plywood edges 7/8 in wide, 250 ft roll 1 roll, heat activated

How we selected the best hardware to use for making nightstands

We opened and read the listing page for every piece in this guide, and we kept only hardware with stated sizes, load ratings and included parts. Each pick suits a nightstand drawer, door, base or plywood edge, and each one is still listed with its specs in place. Nothing here comes from a search snippet or from memory.

We favored hardware that a home builder can install with ordinary tools: slides that adjust after fitting, hinges that clip on and tune in three directions, feet that level a base without shimming, and banding that bonds with heat. We also checked that the load ratings suit the light contents of a bedside drawer, and we left out any piece whose page did not state the size or the rating we needed.

Hardware also comes in packs, so count the drawers and doors before you order. The hinge set in this guide holds 20 hinges, the side-mount slide set holds 10 pairs, and the leveling feet come in packs of 2, 4, 12 or 48. Count the drawers first, then the doors, then the support points at the base, and order the pack that covers the whole build with a spare pair for the drawer you will adjust twice. Check what each pack includes, since brackets, clips and screws are not always in the box: the TANDEM kit includes screws and clips with an optional rear bracket, the side-mount set includes face-frame brackets and screws, and the MOVENTO clip is sold separately.

The best hardware to use for making nightstands

Six pieces cover the whole build: two undermount slides, one side-mount slide set, one hinge set, one leveling foot and one edge banding roll. Each section below gives the stated size, the load rating and what comes in the box, so you can match the hardware to your drawer, your door and your floor.

Blum TANDEM plus BLUMOTION 563H undermount drawer slide

The TANDEM plus BLUMOTION 563H hides under the drawer box, so nothing shows when the drawer opens, and the built-in damper pulls the drawer shut without a slam. The listing page lists lengths of 9, 12, 15, 18 and 21 inches, a 100 pound static load capacity, and a fit for drawer sides of 1/2 inch or 5/8 inch.

The kit includes 2 slides, 2 locking devices and installation screws, while the rear mounting bracket is optional and not included in the standard kit. Adjustment runs in four directions: side to side up to 1/16 inch, height up to 1/8 inch, tilt up to 3/16 inch, and depth up to 3/32 inch with the locking device or 3/16 inch through the elongated holes. The page also states a minimum top clearance of 1/4 inch and a minimum inside drawer width of 4-7/8 inches, so check those numbers before you cut the box. The same slide carries a 90 pound dynamic rating on the 21 inch runner, and that length needs a minimum inside cabinet depth of 21-15/16 inches.

The locking clip sets the drawer height and side position, and the T51.1901 clip adjusts height up to 3 mm and side to side up to 1.5 mm, with a minimum inside drawer width of 170 mm. Because the clip holes sit 32 mm from the inside front corner on a TANDEM box, a box bored for TANDEM clips does not fit MOVENTO clips, so order the box for the platform you run.

The clips decide how much adjustment you get. The 2-way clips give height adjustment, the 4-way clips add lateral adjustment, and the 6-way clips add depth adjustment on top, with the 6-way clips as the default. The rear mounting bracket is only needed in a face-frame cabinet where the slides sit away from the cabinet sides and no blocking fills the gap, so a frameless nightstand usually needs no bracket at all.

Full overlay cabinet hinges, 110 degree soft close, 20 pack

These hinges suit a frameless nightstand with a full overlay door, opening 110 degrees and closing on a built-in hydraulic soft-close mechanism. The listing page states a nickel-plated steel build, a clip-on mount that snaps onto the mounting plate, and 3D adjustment for vertical, horizontal and depth alignment after the door is hung.

The pack holds 20 hinges with installation screws, which covers several doors or a whole run of matching nightstands. The page lists compatibility with door thicknesses from 16 mm to 24 mm, about 5/8 inch to 1 inch, so it suits most residential cabinet doors. Because the hinges adjust in three directions after installation, you can correct height, side gaps and depth without removing the door and drilling again.

The clip-on design lets the door attach to the mounting plate and detach again without removing the whole hinge, which makes fitting, replacement and final alignment faster when several doors are involved. A full overlay door covers the cabinet side panel completely, while a half overlay door covers about half of a shared partition, an inset door sits inside the opening, and a partial overlay door leaves part of the frame visible.

Soft close full extension drawer slides, 10 pairs, side mount

This 10-pair set fits builders who want full drawer access with visible, forgiving side-mount hardware. The listing page states lengths of 12, 14, 16, 18, 20, 22 and 24 inches, a load capacity of up to 100 pounds per pair, and a cold-rolled steel build with a zinc-plated finish for corrosion resistance.

Each slide measures 1/2 inch thick and 1-3/4 inches wide, and the ball bearing system carries the drawer out to full extension so the back of the drawer stays reachable. The pack includes face-frame brackets and installation screws, and the soft-close mechanism controls the final part of the closing motion. Side-mount slides are easier to align than concealed systems, which makes this set a practical choice for a first nightstand build or for replacing worn slides in an older piece.

Cabinet leveling feet, 80 to 110 mm

These plastic leveling feet set a low nightstand base between 80 and 110 mm, about 3.15 to 4.33 inches, with 30 mm of adjustment travel. The listing page states a published load figure of up to 330 pounds, and packs of 2, 4, 12 or 48 pieces, so you can order the count your base plan needs.

Choose this range only when every required setting falls between 80 and 110 mm: a 90 mm setting sits inside the range, while an exact 3 inch setting measures 76.2 mm and falls below the listed minimum. The page also warns that leveling the base does not replace the required wall or floor anchoring for a cabinet run, and that mounting screws and toe-kick clip contents are not assumed, so confirm the supplied hardware before you order.

A toe-kick panel usually finishes the visible space below the cabinet, so plan its setback, attachment and height as a separate step from the legs. Raising the base keeps the cabinet bottom away from direct floor contact, but it does not make plywood or MDF waterproof, so seal vulnerable edges and deal with moisture at its source.

Blum MOVENTO 763H undermount drawer slide

The MOVENTO 763H steps the load up to 125 pounds static, in lengths of 12, 15, 18 and 21 inches, for drawer sides of 1/2 inch to 5/8 inch. Like the TANDEM, it ships with the soft-close damper built into the runner, and it is the only Blum wood drawer runner in this guide that works with TIP-ON BLUMOTION push to open and SERVO-DRIVE.

The H in the name marks the face-frame and rear-bracket capable version of the 763, not a heavier runner: both the 763 and the 763H carry the same 125 pound static rating. The drawer box needs a 50 mm rear notch without TIP-ON, or 125 mm with it, and the matching T51.7601 front locking clip is sold separately, with a minimum inside drawer width of 170 mm. Front to back adjustment comes from the 298.7600 depth adjuster, and face-frame cabinets add a rear mounting bracket or socket so the back of the runner reaches the cabinet back. For a nightstand drawer that holds books, chargers and a full water bottle, the extra load headroom over the 100 pound TANDEM is worth having.

Tandem and Movento share the same inside width rule: the inside drawer width equals the cabinet opening minus 42 mm, and with standard 5/8 inch sides the outside box width lands at the opening minus 10 mm. The bottom recess is 13 mm on every model, and the hook hole measures 6 mm in diameter and 10 mm deep, sitting 7 mm in from the inside face of the side and 11 mm above the notch.

Preglued birch veneer edge banding, 7/8 in by 250 ft

This roll covers the cut edge of birch plywood with a strip of natural birch veneer, so a nightstand carcass shows a continuous wood edge instead of layered plies. The listing page states a 250 foot roll, a 7/8 inch nominal width and a 0.45 mm thickness, with heat-activated adhesive already on the backing and a factory-finished face.

Preglued means the adhesive is already applied and needs a suitable heat process; it does not mean peel and stick. The page warns not to treat the factory-finished face as unfinished veneer, so confirm what preparation and coating are compatible before sanding or staining, and test the bond and trimming on an offcut first. A 250 foot roll is a stock length, not a promise that it will finish a fixed number of plywood sheets, so add the exposed edge lengths across all parts and round up to full rolls. It also states plainly that this thin veneer strip is not structural reinforcement, so choose the shelf material and span for the expected load and use the banding only for the exposed edge.

Before you commit, lay a small length beside the panel in the same orientation as the finished edge, and compare the grain, lightness and coating under the room lighting. This is birch veneer, not a species-matched maple or walnut product, and it is not a solid-color match for white, gray or acrylic MDF panels, so keep the chosen orientation consistent across adjacent shelves and repeated parts.

Buying guide for nightstand hardware

Hardware fails when the size, the mount or the load is wrong, and each of those is easy to check before you order. The notes below walk through the five choices that decide whether a nightstand drawer glides, a door hangs straight and a base sits level. Work through them in order before you cut a single board.

Match the slide length to the drawer box depth

A slide should match the drawer box depth as closely as possible while fitting inside the cabinet, so measure the box and the cabinet depth first. The undermount slides in this guide run 9 to 21 inches or 12 to 21 inches, while the side-mount set runs 12 to 24 inches, which covers most nightstand drawers.

A slide that is too long will not fit, and one that is too short wastes usable space and leaves the back of the drawer unreachable. For a 21 inch undermount runner, the cabinet needs at least 21-15/16 inches of inside depth, so confirm the depth on the listing page for the exact length you plan to buy.

Choose undermount or side mount before you buy

Undermount slides hide under the drawer box and give a clean look with nothing visible when the drawer opens, but they need a notched box and a locking clip cut to the exact model. Side-mount slides install on the left and right sides of the drawer box, stay visible when open, and are easier to align than many concealed systems.

Pick undermount when hidden hardware and a quiet close are the main priorities and your drawer box is built for it. Pick side mount when you want a forgiving install, full extension and simple replacement, or when the cabinet shape makes a notched box impractical. The choice is set by the cabinet, not by taste alone.

Check the load rating against what the drawer holds

A bedside drawer holds books, chargers, medicines and a glass of water, which is far lighter than a kitchen drawer full of pans, yet the rating still matters. The slides in this guide carry 100 pounds per pair or 100 pounds static, while the MOVENTO 763H carries 125 pounds static, so any of them handles a nightstand drawer with room to spare.

Read the rating as a pair, not per slide, and remember that a dynamic rating is lower than a static one: the TANDEM 563H lists 100 pounds static and 90 pounds dynamic on its 21 inch runner. If the drawer will hold a stack of hardcover books, favor the higher rating and keep the heaviest items close to the back of the drawer.

Match the hinge to the door and the cabinet frame

First identify whether the cabinet is face-frame or frameless, then determine whether the door is full overlay, half overlay or inset, and match the hinge style, opening angle and adjustment range to that construction. The hinges in this guide are full overlay for frameless cabinets, with a 110 degree opening and 3D adjustment.

Check the door thickness too: the listing page lists compatibility with doors from 16 mm to 24 mm, about 5/8 inch to 1 inch. The listing page also offers a quantity calculator that estimates the hinge count from door height, and notes that the final count depends on door weight, width and material, so use it rather than guessing. For a door near a wall or another door, add a restrictor clip that limits the opening angle and keeps the door from hitting what stands beside it.

Measure the base before you order leveling feet

Measure at the actual leg locations, since a level cabinet over an uneven floor can need different settings at each corner. The leveling feet in this guide adjust from 80 to 110 mm with 30 mm of travel, and each of the three models on the listing page offers the same 30 mm span, so a taller model does not give more leveling travel.

Choose the model that covers the required setting at every support point, and leave adjustment margin where the design allows. Count the legs from the support plan, since a four-piece pack is not a promise that four legs suit every cabinet, and confirm the mounting plate and hole pattern against your base before ordering.

Frequently asked questions about nightstand hardware

These are the questions that come up most when a nightstand is built from scratch instead of bought finished. The answers below stick to what the listing pages state and to plain workshop sense. Read them before you order, since the wrong slide length or hinge type costs more to fix than to choose well.

What size drawer slides do I need for a nightstand?

Match the slide length to the drawer box depth and the available cabinet depth. A typical nightstand drawer is 12 to 18 inches deep, so the 12, 15 and 18 inch lengths in this guide cover most builds, while the 21 and 24 inch lengths suit deeper drawers.

Measure the drawer box depth first, then check the minimum inside cabinet depth for that length: a 21 inch undermount runner needs at least 21-15/16 inches inside the cabinet. A slide that is too long will not fit, and one that is too short wastes space at the back of the drawer.

Do I need soft-close slides for a nightstand drawer?

You do not need them, but they help in a bedroom, where a drawer that slams shut at night wakes the room. Every slide in this guide closes softly: the undermount runners carry a built-in damper, and the side-mount set uses a soft-close mechanism that controls the final part of the closing motion.

Soft close adds cost and needs a square, level install to feel right, since a slide mounted out of square can leave the damper feeling unresponsive. If the budget is tight, a standard ball-bearing slide still glides well, but the soft-close versions in this guide are the quieter choice for a bedroom.

What hinge opening angle works for a nightstand door?

A 110 degree opening angle gives a nightstand door enough range for everyday access while keeping the hinge stable and controlled, and it is one of the most popular opening angles for residential furniture. The hinges in this guide open 110 degrees with a built-in hydraulic soft-close mechanism.

Wider angles suit corner cabinets and Lazy Susan doors, where the door must fold back further, but a standard nightstand door does not need them. Match the angle to the cabinet layout, and check the door thickness and overlay type before ordering, since those decide the fit more than the angle alone.

Can I use edge banding on a plywood nightstand?

Yes, and it is the usual way to finish a plywood carcass: the banding covers the layered cut edge with a strip of natural birch veneer. The roll in this guide measures 250 feet long, 7/8 inch wide and 0.45 mm thick, with heat-activated adhesive already on the backing.

Measure the actual sheet before ordering, since the 7/8 inch width is nominal and a thinner panel leaves overhang to trim. Test the bond and trimming on an offcut first, and do not treat the factory-finished face as unfinished veneer: confirm what preparation and coating are compatible before sanding or staining.

How do I level a nightstand on an uneven floor?

Fit adjustable leveling feet and set each one to the height its corner needs, measuring at the actual leg locations. The feet in this guide adjust from 80 to 110 mm with 30 mm of travel, so each corner can sit at a different setting within that range until the base reads level.

Check both ends of the required span, including front and rear supports, rather than measuring only one corner. Leveling the base does not replace the required wall or floor anchoring, so follow the cabinet maker support and anchoring instructions once the base is level.

Conclusion

Start with the TANDEM 563H for a hidden drawer, the 110 degree hinges for a frameless door, and the side-mount set when the build favors visible hardware. Level the base with the 80 to 110 mm feet, band the plywood edges, and measure twice before you order anything. Order hardware before cutting the boxes, so the notches land right.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.