Updated Nov 16, 2026· 15 min read

Key takeaways

  • USB mixers for guitar compared: AG06MK2, Model 12, Onyx8, StudioLive AR8c, LiveTrak L-8 and AG03MK2, with Hi-Z inputs, amp simulation and multitrack USB listed.

A guitar plugged straight into a mixer needs the right input before it needs anything else. These usb mixers for guitar all publish a Hi-Z or instrument input for direct connection, and they split by ambition: two add amp simulation, three record multitrack, and one does both jobs at band scale, with the specs to prove it.

Quick verdict

The six divide by session size. The AG06MK2 and AG03MK2 are guitar-first desks with amp simulation for one player. The Onyx8 and StudioLive AR8c are analogue multitrack mixers with two instrument inputs each. The Model 12 and LiveTrak L-8 scale up: eight Hi-Z inputs on the Tascam, battery multitrack on the Zoom.

Mixer Instrument input USB recording Standalone recording Best for
Yamaha AG06MK2 Hi-Z on CH2, plus AMP SIM 2-in/2-out, 24-bit/192 kHz None Guitar-first tracking at a desk
Tascam Model 12 8 Hi-Z inputs 12-in/10-out 12 tracks to SD card Bands and full sessions
Mackie Onyx8 2 Hi-Z inputs 8-track multitrack, 24-bit/96 kHz Stereo mix to SD card Analogue multitrack, small desk
PreSonus StudioLive AR8c 2 Hi-Z inputs, over 1 Mohm 8×4, 24-bit/96 kHz Main mix to SD card Hybrid analogue recording
Zoom LiveTrak L-8 Hi-Z on channels 1-2, 1 Mohm 12-in/4-out, 24-bit/48 kHz 10 tracks plus mix to SD card Portable multitrack anywhere
Yamaha AG03MK2 Hi-Z on CH2, plus AMP SIM 2-in/2-out, 24-bit/192 kHz None Smallest guitar streaming desk

Read the instrument-input column first, because it is the whole point of this keyword: an impedance figure or a Hi-Z label from the maker, not a line input pressed into service. Then match the recording column to your session, from a single direct track to a full band.

How we selected

The rule for this list was strict: a mixer qualified only if its product page states a Hi-Z or instrument input and a USB audio connection. Every product below meets both conditions in the maker’s own published specifications, with the input impedance or gain range quoted where the maker publishes one.

Mixers whose pages offer only line inputs were left out, however good their preamps, because a passive guitar into a line input loses level and top end in ways EQ cannot fully restore. Amp simulation counted as a bonus, never a requirement: two of the six include it, and the buying guide explains when that matters.

Six usb mixers for guitar, compared in detail

Two small Yamaha desks built around a guitar channel, two analogue multitrack mixers with instrument inputs, and two recorder-mixers that count the guitar as one voice in a full session. Each entry states the published instrument-input evidence first, then the recording path it feeds.

Yamaha AG06MK2

The AG06MK2 is the guitar streamer’s desk: its second channel is a dedicated Hi-Z guitar input, and its DSP includes an amp simulator, so a direct guitar can be tracked or streamed with an amp-like tone and no microphone, no amp and no plug-in latency. For singer-guitarists it is the most direct route here.

The guitar channel sits inside a six-channel mixer: a combo microphone input with phantom power and a headset option, a stereo line channel, a smartphone connection over TRRS, and USB audio. The DSP block adds one-touch compression and EQ plus SPX reverb alongside the amp simulation, all monitored with zero latency, and the AG Controller app opens the detailed settings.

USB carries two channels each way at up to 24-bit and 192 kHz, and the STREAMING OUT selector chooses between a dry feed, the input mix and loopback for computer audio. The desk is USB bus powered and measures 152 x 63 x 201 mm at 0.9 kg. Cubase AI and WaveLab Cast software are included.

The limits are the format’s: one guitar input, one microphone preamp, and a stereo USB path, so a full band is out of scope. The maker does not publish a preamp gain figure for this model. What it publishes instead is the complete guitar workflow, input, amp simulation and monitoring, in one small box.

  • Pros: dedicated Hi-Z guitar input with amp simulation built in; zero-latency DSP monitoring; compact, bus powered, high-resolution stereo USB.
  • Cons: one instrument input and one preamp only; stereo USB rather than multitrack; gain figure not published.
  • Buy if: you are a guitarist who sings, streams or tracks alone and wants an amp sound without an amp.
  • Skip if: you record more than one instrument at a time or need multitrack USB.

Tascam Model 12

The Model 12 is the full-session answer: eight of its ten input channels switch to Hi-Z, so guitars, basses and other instruments plug straight in alongside eight Ultra HDDA microphone preamps. It is a mixer, a multitrack recorder and a USB interface in one unit, aimed at bands that rehearse, record and perform with the same desk.

Every input channel carries a one-knob compressor and 3-band EQ, channels ride on 60 mm faders, and the recorder captures 12 tracks to an SD card at 24-bit and 48 kHz with punch-in and punch-out and overdubbing. A metronome with a click output keeps takes honest, and Bluetooth and a smartphone input with mix-minus cover playback and calls.

Over USB it is a 12-in and 10-out interface with DAW control from its surface over HUI and MCU protocols. Two headphone outputs, MIDI connections and an output delay for video work round out a specification that counts the guitar as one member of an ensemble. The unit measures 343 x 98.8 x 360 mm and weighs 4.3 kg.

The limits are size and commitment: this is a desk, not a desktop accessory, and its per-channel simplicity (one-knob compression, fixed EQ) trades depth for speed. The maker does not publish preamp gain or noise figures on the product page. For a guitarist in a band, though, eight instrument inputs is a specification nothing else here matches.

  • Pros: eight Hi-Z inputs, more than any other model here; multitrack SD recording plus 12-in/10-out USB; per-channel compression and EQ.
  • Cons: large and mains-powered; no amp simulation, direct tones are dry; gain and noise figures not published.
  • Buy if: your guitar is one of several instruments recorded together, live or in rehearsal.
  • Skip if: you play and record alone at a desk and want the smallest possible setup.

Mackie Onyx8

The Onyx8 brings the analogue multitrack format down to eight channels: two of its inputs are dedicated Hi-Z connections for guitars, basses and other instruments, beside four Onyx microphone preamps with up to 60 dB of gain. For a guitarist who also records a vocal and a second instrument, it is the balanced middle of this list.

The channel processing is Mackie’s Perkins EQ, a 3-band design with a sweepable midrange on the mono channels and a hard bypass switch, plus a 100 Hz high-pass filter and phantom power across the microphone channels. Built-in effects are handled through a full-color display, and a Bluetooth input covers playback from a phone.

Recording runs two ways: multitrack to a computer over USB at 24-bit and 96 kHz, with a four-track USB return assignable to channels for overdubs, or a stereo mix straight to an SD card when no computer is present. A control room output and aux and FX sends give it small-live-rig manners as well.

The limits: the two Hi-Z inputs serve one guitarist and one bassist, not a full band’s worth of direct instruments, and the SD recording is the stereo mix only, not multitrack. The maker’s page does not state dimensions or weight, and current stock is worth confirming before ordering.

  • Pros: two Hi-Z inputs beside four strong preamps; multitrack USB at 96 kHz plus SD stereo capture; Perkins EQ with sweepable mid.
  • Cons: SD recording is stereo only; no amp simulation; stock signals conflict between dealers.
  • Buy if: you record guitar, bass and vocals in small combinations and like an analogue surface.
  • Skip if: you need standalone multitrack recording away from a computer.

PreSonus StudioLive AR8c

The AR8c is the specification sheet’s favorite: its two instrument inputs are proper Hi-Z connections with an input impedance above 1 Mohm and a published dynamic range above 105 dB, which is exactly the evidence a guitarist should look for. Four Class A XMAX preamps with gain from +12 to +55 dB handle microphones beside them.

Every channel carries a highpass filter (a 100 Hz low cut in the spec table) and a 3-band semi-parametric EQ whose mono mid band sweeps from 140 Hz to 3.5 kHz, useful for finding where a direct guitar sits against a vocal. A stereo effects processor offers 16 presets with a footswitch bypass jack, a genuinely gig-friendly touch for a guitarist.

USB recording is 8×4 at 24-bit and 96 kHz over a USB-C connection, and a 2×2 SD recorder captures the main mix without a computer. The Super Channel adds Bluetooth 5.0, RCA and mini-jack inputs plus SD and USB playback. Capture and Studio One Artist software are included, and the unit measures 89 x 284 x 313 mm at 3.2 kg.

The limits: the SD recorder takes the main mix only, and the instrument inputs’ maximum level is +9 dBu, so very hot active pickups need the gain watched. Availability varies between sellers, so confirm current stock before planning a session around it.

  • Pros: published Hi-Z impedance above 1 Mohm with full gain and dynamic-range figures; effects bypass footswitch; USB-C connection.
  • Cons: SD capture is the main mix only; +9 dBu instrument ceiling is modest for hot active pickups; availability varies by dealer.
  • Buy if: you want analogue mixing with the most completely documented instrument inputs here.
  • Skip if: standalone multitrack recording matters more than the analogue surface.

Zoom LiveTrak L-8

The L-8 is the portable multitrack option: channels 1 and 2 are Hi-Z inputs at 1 Mohm for guitar and bass, with a published gain range of -3 to +41 dB in Hi-Z mode, and the whole mixer runs on four AA batteries. A guitarist can track a full session in a rehearsal room, a park or a tour van, then finish it at a computer.

Six microphone preamps with selectable phantom power, two line channels and a smartphone input with mix-minus surround the guitar channels. Each channel has 3-band EQ and a low-cut filter, eight effect types are built in, six sound pads trigger samples, and seven scene memories store whole setups for different bands or rooms.

Recording is the strength: up to 10 discrete tracks plus a stereo mix go to an SD card at up to 24-bit and 96 kHz, while USB turns the L-8 into a 12-in and 4-out interface at 24-bit and 48 kHz for a computer or iOS device. Four headphone outputs with their own mixes serve a full band. The unit measures 268 x 282 x 74 mm and weighs 1.6 kg.

The limits are stated by the maker: EQ, effects and overdubbing are unavailable at the 96 kHz recording rate, battery life on alkalines is about two hours, and the USB interface rate tops out at 48 kHz. None of that stops it being the only battery multitrack recorder here with proper instrument inputs.

  • Pros: Hi-Z inputs with published impedance and gain range; battery-powered multitrack recording; four headphone mixes.
  • Cons: processing unavailable at 96 kHz; USB interface limited to 48 kHz; alkaline battery life is short.
  • Buy if: you record guitars and bands away from a desk and want every part on its own track.
  • Skip if: your sessions always happen at one desk with a computer already running.

Yamaha AG03MK2

The AG03MK2 is the AG06MK2’s smaller sibling and the smallest guitar desk here: channel 2 is a Hi-Z guitar input, and the same zero-latency DSP provides amp simulation, one-touch compression and EQ, and reverb. For a guitarist who only ever records one microphone and one guitar, it gives up nothing that matters.

Channel 1 is a combo microphone input with phantom power, a 60 mm fader and a mute button, and it also accepts a headset microphone. A stereo line channel, a TRRS smartphone connection and the STREAMING OUT selector with loopback cover backing tracks, calls and computer audio.

USB audio runs two channels each way at up to 24-bit and 192 kHz over USB Type-C, bus powered, and Cubase AI plus WaveLab Cast are included. The AG Controller app reaches the detailed DSP settings behind the one-touch front panel.

The limits mirror the AG06MK2’s, tighter: one microphone, one guitar, stereo USB, and no published gain figure or dimensions on the opened page. The choice between the two Yamaha desks is simply channel count: a second stereo source or a guest microphone argues for the AG06MK2; a strict voice-plus-guitar format fits the AG03MK2 exactly.

  • Pros: Hi-Z guitar input with amp simulation in the smallest format here; 60 mm fader and mute on the voice channel; high-resolution stereo USB.
  • Cons: strictly one microphone and one instrument; no multitrack path; gain figure not published.
  • Buy if: your entire act is one voice and one guitar, streamed or tracked at a desk.
  • Skip if: a second player, a stereo instrument or a guest microphone is likely.

Buying guide

For guitar, a USB mixer succeeds or fails at one socket: the instrument input. Everything after that, EQ, effects, multitrack, is shared with every other recording task. Read the input specification first, then decide how much mixer around it your sessions actually need.

What usb mixers for guitar must get right

The instrument input must present a high impedance to the pickup, around 1 Mohm, or the guitar loses level and brightness before recording starts. The AR8c publishes above 1 Mohm and the L-8 exactly 1 Mohm; the Onyx8 and the Yamaha and Tascam desks publish the Hi-Z designation itself. A named Hi-Z input is the minimum evidence.

Gain range matters next, because passive pickups are quiet and active ones are loud. The L-8 publishes -3 to +41 dB in Hi-Z mode and the AR8c +12 to +55 dB shared with its preamps. Where a maker publishes neither impedance nor gain, as with the Yamaha pair, the dedicated guitar channel and amp simulation still mark the design intent.

Direct and dry, or amp simulation built in

A direct guitar recording is a dry signal: flexible in the DAW, lifeless in the headphones while you play. Amp simulation fixes the playing experience. The two Yamaha desks include it in their DSP with zero-latency monitoring, so what you hear while tracking is an amp-like tone, while the recording can still be managed in software.

The other four record the honest dry signal and expect amp plug-ins or re-amping later. That is the better workflow for producers who change tones after the take, and the worse one for players who perform to the sound. Decide which you are before choosing, because no mixer here can be upgraded from one camp to the other.

One guitar, or every instrument in the room

Count the direct instruments in your biggest session. One guitar: any of the six. Guitar and bass together: the Onyx8, AR8c or L-8, each with two instrument inputs. A full band going direct: only the Model 12, whose eight Hi-Z inputs take guitars, basses and keyboards without a single DI box in the chain.

The same count drives the recording format. Stereo USB serves the solo guitarist completely. Multitrack USB or SD recording, on the Onyx8, Model 12 and L-8, is what turns a jam into separate tracks that can be mixed later. Buying multitrack before you need it is harmless; needing it after you bought stereo is a second purchase.

Monitoring while you track

A guitarist plays to what they hear, so monitoring is a tone control. The Yamaha desks monitor their DSP directly with no latency. The L-8 gives four headphone outputs with separate mixes, so a band tracks together with each player hearing their own balance.

The analogue pair monitor through their control room and headphone paths in the traditional way, and the Model 12 provides two headphone outputs for an engineer and a player. Whichever you choose, confirm the direct or DSP path exists; playing through a DAW round trip at high buffer sizes is the one experience every guitarist here is paying to avoid.

FAQ

The questions guitarists ask when a mixer replaces an amp as the recording front end: what Hi-Z actually does, whether a DI box is still needed, and how the dry-versus-simulated choice plays out in practice. Most come down to impedance, tone and habit.

Do usb mixers for guitar replace an amp?

For recording, the two Yamaha desks come closest: their amp simulation gives a direct guitar an amp-like tone in the headphones and on the track, with no microphone and no speaker. The other four replace the amp’s input stage and recording chain, but the tone itself comes from plug-ins or later re-amping.

For playing live through speakers, none of them is an amp; they are mixers, and they feed powered speakers or a PA. The honest summary is that a USB mixer replaces the amp as a recording input completely, and as a sound source only where simulation is built in.

Why does a guitar need a Hi-Z input at all?

A passive pickup is a high-impedance source. Plug it into a low-impedance line input and the signal loses level and high frequencies, arriving dull and weak in a way that EQ can only partly repair. A Hi-Z input, around 1 Mohm as published for the AR8c and L-8, loads the pickup correctly and keeps the full signal.

That is why this list required the designation on the product page. A mixer with excellent preamps but only line inputs is the wrong tool for a direct guitar, and no amount of gain restores the top end that the wrong impedance took away at the socket.

Do I still need a DI box with one of these mixers?

Not for the instruments these inputs cover: the Hi-Z input is the DI function, built into the channel. A guitar or bass plugs straight in on the Onyx8, AR8c, L-8, Model 12 and both Yamaha desks, and the mixer handles level and impedance from there, at the desk.

A separate DI box still earns its keep in two situations: splitting a signal to an amp and a mixer at once, and ground-lift duty on a noisy stage. For a straight recording setup at home or in rehearsal, the built-in instrument inputs make the extra box unnecessary.

Can I record a guitar amp through these mixers too?

Yes, through the microphone inputs, which is the traditional route: a microphone in front of the cabinet into one of the preamps every model here provides. The Onyx8 offers four preamps with up to 60 dB of gain, the AR8c four XMAX preamps, the Model 12 eight, and the L-8 six, all with phantom power for condensers.

Many players record both at once: the direct Hi-Z track for editing and re-amping, the microphone track for the real cabinet sound. That needs two channels per guitar, which is another reason the multitrack models suit guitarists who record seriously.

Which of these is best for a guitarist who also sings?

The Yamaha AG06MK2 is built for exactly that format: one phantom-powered microphone channel, one Hi-Z guitar channel with amp simulation, and DSP that polishes both at once, voice with compression, EQ and reverb, guitar with its simulated amp. The AG03MK2 runs the same pairing smaller.

The multitrack models serve the singing guitarist too, with more room to grow, but their guitar channels are dry and their extra inputs wait for a band. If the act is one person, the purpose-built desk feels finished sooner.

Conclusion

The right first step is the input itself: a published Hi-Z spec with impedance and gain figures you can check. Match that to your session, the AG pair for direct amp-sim tracking, the Onyx8 and AR8c for analogue multitrack, the Model 12 and L-8 when the guitar is one voice among many. Choose by the next session you will actually play.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.