Updated Nov 16, 2026· 14 min read

Key takeaways

  • Five food processors for making hamburger, each one backed by a maker-printed meat capacity or a booklet section on chopping meat, from 1 pound to 2-1/4 lbs.

A processor makes hamburger by chopping, not by grinding, and the difference shows in the texture. The honest evidence for this job is a maker who prints a meat capacity or a meat technique in the booklet. Every food processors for making hamburger pick below has exactly that: a stated amount of meat the maker rates its blade to chop, in print.

Quick verdict

The Cuisinart Custom 14 is the standout: its booklet names meat for hamburger directly and rates chopped or pureed meat at 2-1/4 pounds, the highest figure here. The Cuisinart Elemental 13 follows at 2 pounds. The KitchenAid KFP0921 is the compact pick, with a printed 1 pound limit for raw or cooked meat.

Product Type Best for Key spec Main limit
Cuisinart Custom 14 (DFP-14BCNY) Full-size processor Largest printed meat batches Chopped or pureed meat rated 2-1/4 pounds Single speed plus pulse only
Cuisinart Elemental 13 (FP-13DGM) Full-size processor, two bowls Big batches and small test grinds Chopped or pureed meat rated 2 pounds 550 watt peak power rating
Cuisinart Pro Custom 11 (DLC-8SBCY) Full-size processor Full meat technique sections Booklet covers chopping and pureeing meat Booklet prints no meat weight in the pages read
Hamilton Beach Stack & Snap (70725A) Full-size processor Chart-driven processing Manual chart lists meat under Chop Manual prints no meat weight limit
KitchenAid 9 Cup (KFP0921) Mid-size processor Small households, 1 pound batches Manual rates meat at up to 1 pound Smallest meat rating in the group

How we selected

The rule for this list was strict: a model counted only when a page opened for this project states a meat chopping function, a meat capacity, or a meat technique for that model. General chopping power did not count, and neither did a chart entry that names mincing without naming meat. Two strong processors were set aside on exactly that ground.

That rule is why three Cuisinart booklets anchor the list. Cuisinart prints meat capacities in its capacity charts and writes full technique sections for chopping meat, which is the documentation a buyer needs before trusting a blade with a chuck roast. The Hamilton Beach and KitchenAid manuals print meat in their processing guidance too, with the KitchenAid adding an explicit weight limit per batch.

Every figure below comes from a listing or booklet opened for this project. Where a maker prints a function but no weight, the entry says so. No model here is presented as a meat grinder, because no maker in this group describes its processor as one: the printed verb is chop, and the articles and charts use it that way.

Food processors for making hamburger, model by model

Five machines follow, ordered by the strength and size of their printed meat evidence. The first two carry numeric meat ratings above 2 pounds. The next two carry meat in their charts and technique sections without a printed weight. The last carries the clearest small-batch limit in the group.

Cuisinart Custom 14 (DFP-14BCNY)

The Custom 14 booklet does something rare: it names this exact job. In its practice section, the maker writes, “Try chopping other food, like meat for hamburger or sausage.” Its capacity chart then rates chopped or pureed meat, poultry, fish or seafood at 2-1/4 pounds, the largest meat figure printed by any machine in this roundup.

The technique pages fill in the method. The metal blade chops raw and cooked meat to the consistency the cook wants, from coarse to fine, and even to a puree. Pieces should be about the same size, and the booklet’s general chopping guidance runs at 1-inch pieces with pulse control for even results. The machine itself is a 720 watt design with a 14-cup bowl, a 4mm slicing disc, a medium shredding disc and an extra-large feed tube, listed with a limited 3-year warranty on the unit and a full 5-year warranty on the motor.

The limits are control and documentation scope. The Custom 14 runs a single speed with On and Off/Pulse levers, so grind texture is managed entirely by pulse count and run time. Its chart also groups meat with poultry, fish and seafood under one figure, so the 2-1/4 pounds is a shared ceiling across those foods rather than a beef-only rating.

Buy it if you grind hamburger in family-size batches and want the maker to rate the job in print. Skip it if you want speed steps for texture control, or if a dedicated grinder’s auger texture is what you are after, because a chopping blade gives a different, softer crumble.

Cuisinart Elemental 13 (FP-13DGM)

The Elemental 13 booklet chart rates chopped or pureed meat, fish or seafood at 2 pounds (907 g) in the large 13-cup bowl. That is the second-highest printed meat figure here, and it comes with a second, 4.5-cup bowl for the small test batch a cook runs before committing a whole roast to the blade.

The machine runs a 550 watt peak power motor, and the booklet notes the rating is based on the shredding disc, the attachment that draws the greatest current. The large stainless steel chopping and mixing blade uses the maker BladeLock system to stay seated while pouring, the cover seals with the SealTight Advantage system, and the box adds an adjustable slicing disc, a reversible shredding disc, a dough blade and a dicing kit on this configuration. Touchpad controls offer High, Low, Off and Pulse.

Two limits stand out. The 2 pound figure again groups meat with fish and seafood, and the booklet’s small bowl chart does not list a meat capacity, so small-batch meat work runs under the large bowl’s rating. The listing for this model carried no explicit stock flag in the text read for this project, so confirm sale status before ordering.

Buy it if you want a 2 pound printed meat rating plus a nested small bowl for seasoning tests and small patties. Skip it if you want the absolute largest meat batches, or if a wattage figure beyond a peak rating matters to your comparison.

Cuisinart Pro Custom 11 (DLC-8SBCY)

The Pro Custom 11 manual gives meat the fullest technique treatment in this group: separate sections titled “To chop meat, poultry, fish and seafood” and “To puree meat, poultry, fish and seafood.” Like its bigger sibling, it also names the job in practice, suggesting the cook try chopping “meat for hamburger or sausage.”

The method is specific. The food should be very cold but not frozen, cut into 1-inch pieces for an even chop, and worked with the OFF/PULSE lever three or four times at one second on and one second off, then run continuously for a few seconds if a finer texture is wanted. The manual describes the metal blade chopping meat from coarse to fine, even to a puree. The machine is an 11-cup design with a 625 watt motor, an extra-large feed tube, a thin 2mm slicing disc, a medium 4mm slicing disc and a shredding disc, listed with a full 5-year motor warranty and a limited 3-year warranty on the unit.

The gap is a number: the manual pages read for this project print the meat technique without a meat weight in the sections quoted, so batch sizing runs on the 11-cup bowl and the technique rather than a rated ceiling. The dealer page opened for this model also carried no explicit stock flag in its text, so confirm sale status before ordering.

Buy it if you want the most detailed maker guidance on meat texture in this group, in a slightly smaller machine than the Custom 14. Skip it if a printed meat weight is the figure you plan batches around.

Hamilton Beach Stack & Snap (70725A)

The Hamilton Beach manual puts meat in its processing chart in plain terms. Under the chopping and mixing blade, the chart reads: “Chop: nuts, meat, garlic, onions, peppers, celery, herbs, bread (for crumbs), crackers.” That single line is the maker stating a meat chopping function for this model, which is what this list requires.

Around that line, the manual gives the machine’s working limits: dry ingredients up to 12 cups (2.8 L), vegetables or fruits up to 3 pounds (1.4 kg), cheese up to 40 ounces (1.2 L), thick sauces or dips up to 8 cups (1.9 L) and liquids up to 7 cups (1.7 L). The processor itself runs a 450 watt motor with 2 speeds plus pulse, a 12-cup sealed bowl, an S-blade and a reversible slicing and shredding disc, at 8.5 x 9.1 x 16.1 inches and 6.57 pounds. The control panel carries a dedicated Puree position alongside Chop, Mix, Slice and Shred.

The limit is precision: the chart names meat without a meat-specific weight, so the batch ceiling for hamburger is a judgment call against the bowl’s other printed maximums rather than a rated figure. The manual also directs that dough kneading is off the menu for this model, which matters if one machine has to cover both jobs.

Buy it if you want a stated meat function in a lighter, simpler machine and you grind modest batches. Skip it if you need a printed meat weight, or if the same machine must also knead dough.

KitchenAid 9 Cup (KFP0921)

The KitchenAid manual is the most direct of the five about batch size. Its tips section reads: “To chop cooked or raw meat, poultry, or seafood: The food should be very cold. Cut into 1 inch (2.5 cm) pieces. Process up to 1 pound (455 g) at a time to the desired size, using short pulses, 1-2 seconds each time.”

That 1 pound ceiling makes this the small-batch machine of the group, and the rest of the manual suits that role. The work bowl holds 9 cups (2.1 L), all accessories store inside it, and the parts list runs to a multi-purpose four blade, a reversible slicing and shredding disc, a whisking accessory, a dough blade and a refrigerator lid. Controls are Low, High and Off/Pulse, with pulse at high speed. KitchenAid lists a one-year full warranty in the United States, and the manual specifies 120 VAC power.

The trade-offs are size and documentation. One pound per batch means a family burger night runs in several rounds, and the manual states no motor wattage, so no wattage is claimed here. The accessories guide also pairs its Mince or Puree action with sauces and pesto rather than meat, so the meat case rests on the tips section alone.

Buy it if your hamburger batches are a pound at a time and counter space is tight. Skip it if you grind for a crowd, or if you want the maker to state a wattage and a larger meat rating.

Buying guide

Grinding hamburger in a processor is a controlled chop: the blade cuts cold meat into smaller and smaller pieces until the texture matches what the patty needs. The checks below follow the booklets in this roundup, from the evidence to look for on the page to the fat and temperature decisions that decide the result.

Demand a printed meat figure or function

Meat is the load that separates honest documentation from marketing. A maker that rates meat in its capacity chart, or names meat in its processing chart, has engineered and written for the job. A maker that prints only generic chopping claims may still chop meat, but it has not told you the batch size or the method it stands behind.

Read the figure’s scope. Most charts group meat with poultry, fish and seafood under one ceiling, which means the number is a shared maximum for dense protein, not a beef-only promise. Treat it as the ceiling for the whole batch, including any fat or seasoning mixed in.

Batch size and fat content for food processors for making hamburger

Batch size is the printed rating, full stop: 2-1/4 pounds at the top of this group, 1 pound at the compact end. Overfilling is the main cause of uneven grind, because pieces above the blade ride untouched while the layer at the blade turns to paste. Two half batches take minutes longer and grind evenly.

Fat content is the cook’s choice, not the machine’s rating. The booklets do not grade grinds by fat percentage; they ask for cold meat in even pieces. A fattier cut grinds softer and binds patties with less working, while a lean cut needs shorter runs to stay coarse. Decide the blend before the meat goes in, because a processor cannot add fat evenly after the chop.

Cold meat, even pieces, short pulses

Every meat section in these booklets repeats the same three instructions. The meat should be very cold but not frozen. It should be cut into 1-inch pieces so the blade meets uniform resistance. And it should be worked in short pulses, one or two seconds at a time, with the texture checked between bursts.

The reason is friction. A blade running continuously warms the fat, and warm fat smears instead of cutting cleanly, which gives hamburger a dense, sausage-like texture. Pulsing keeps the fat in distinct pieces, and distinct fat pieces are what make a ground patty cook up juicy rather than tight.

Texture control without a grinder

A processor chop is softer and less uniform than an auger grind, and the booklets are honest about the range: coarse to fine, even to a puree. For hamburger, the useful zone is the coarse half of that range. Stop while the pieces are still distinct, because the patty itself will bind them during shaping.

Work in a shallow layer and scrape the bowl sides down between pulse rounds, as the manuals direct. Meat climbs the walls under the blade, and the unscraped ring at the top is the part that stays chunky while the bottom over-processes.

Cleaning after meat work

Meat leaves fat film on blades, bowls and lids. Several machines in this group list their bowls, blades and accessories for dishwasher cleaning; others ask for hand washing of specific parts. Check the care line for the exact model, and wash meat-contact parts promptly, because dried fat and protein are far harder to remove than fresh residue.

Blade handling deserves the same care as the washing itself. Every manual in this group warns that the chopping blade is sharp and should be lifted by its hub, never by the edges, and stored on its own rather than loose in a drawer.

FAQ

Five questions cover the ground buyers hesitate on: whether a processor result counts as ground beef at all, how fine the chop can go, how much meat fits in a batch, which cuts the booklets suit, and how processor hamburger differs from a dedicated grinder’s output at the table.

How fine can food processors for making hamburger grind?

As fine as a puree, by the makers’ own wording, but hamburger wants the coarse end of the range. The Cuisinart booklets describe the metal blade chopping meat from coarse to fine and even to a puree, and the control is time: short pulses for a coarse, loose grind, longer runs for a fine one. For patties, stop at coarse, with pieces still distinct.

Overshooting is the common mistake. Once the mixture turns smooth and paste-like, it cooks up dense. If a batch goes too far, fold it together with a coarsely chopped second batch rather than serving it as is.

Is processor-chopped meat really hamburger?

It is ground meat made by a different tool. A grinder pushes meat through a plate for a uniform, stranded texture. A processor chops it with a blade for a softer, less uniform one. The booklets use the word hamburger themselves for the processor result, and the Custom 14 and Pro Custom 11 manuals suggest chopping “meat for hamburger or sausage.”

The difference shows in the patty: processor hamburger binds a little more loosely and cooks a little more tender. Many cooks prefer it for smash-style and thick pub patties alike, as long as the chop stays coarse and the fat stays cold.

How much meat can I grind in one batch?

Only what the maker prints. The ratings in this group are 2-1/4 pounds for the Custom 14, 2 pounds for the Elemental 13 and 1 pound for the KitchenAid KFP0921. The Pro Custom 11 and the Hamilton Beach print the meat function without a meat weight in the pages read, so their batches should stay modest against their bowl sizes.

When the recipe needs more than the rating, grind in rounds. Each round takes a few minutes, and the texture stays even in a way one overloaded bowl never matches.

Which cuts suit processor hamburger?

The booklets do not name cuts; they specify condition instead: very cold, not frozen, cut into 1-inch pieces. Any grinding cut that meets those conditions works in the bowl. Chuck is the traditional choice for its fat balance, and blends with brisket or short rib follow the same rule of cold, even pieces.

Trim with the patty in mind. The blade chops sinew less willingly than fat or muscle, so heavy connective tissue is better trimmed out before the meat goes in than picked out of the grind afterward.

Can a processor replace a meat grinder entirely?

For hamburger in home quantities, the makers in this group say yes by printing the job in their booklets. For sausage making at scale, long grinding sessions or very uniform commercial texture, a dedicated grinder remains the right tool, because its auger and plate are built for continuous meat work in a way a batch bowl is not.

The practical line is frequency and volume. A household that grinds a few pounds a week is well served by a rated processor. A household that processes a whole animal each season is asking a batch appliance to do a continuous appliance’s work.

Conclusion

The Cuisinart Custom 14 is the firm pick: its booklet names meat for hamburger and rates the job at 2-1/4 pounds. The Elemental 13 follows closely at 2 pounds with a second bowl for small batches. For a pound at a time, the KitchenAid KFP0921 prints the clearest limit. Buy the machine whose maker rates your batch size in print.

A
admin88
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.