Key takeaways
- Compare six pull-out kitchen faucets with spray wands from Moen, Delta, Kohler, Pfister, Glacier Bay and GROHE, with flow rates, reach and full hose details.
A fixed spout leaves the far corners of a wide sink dry and turns rinsing a roasting pan into a two-handed shuffle. The kitchen faucets with pull out wand designs below put the spray head on a hose, so the water goes where the work is. This guide compares six current models by flow rate, spout reach, hose design and spray functions.
Quick verdict
Every model in this roundup pulls its spray head out of the spout on a hose, and each one publishes the numbers that matter: flow rate, spout reach and hole count. The Moen Brecklyn leads on spray force, the Pfister Marielle on flow, and the Kohler Coralais on hose handling, while the Delta, Glacier Bay and GROHE entries suit tighter decks.
Start with the Brecklyn if the sink is wide and the pans are large, because its listing names a pull out spray wand feature and a Power Clean spray function. Choose the Marielle if a soap dispenser in the box matters, since its specification sheet lists a top filling dispenser as included. Pick the Coralais if hose manners matter most, because Kohler builds the pull-out around a braided hose and a swiveling ball joint.
| Product | Type | Best for | Key spec | Main limit |
|---|---|---|---|---|
| Moen Brecklyn 87557SRS | Pull-out, single handle | Strong spray work | 1.5 GPM, Power Clean spray | Low arc limits tall pots under the spout |
| Delta Foundations B4310LF | Pull-out, single handle | Long hose reach | 1.8 gpm, 59 inch hose | Ball valve design is older in style |
| Kohler Coralais K-15160 | Pull-out, single lever | Hose handling | 1.8 gpm, 9 inch reach | White sprayhead suits fewer kitchens |
| Pfister Marielle F532-7P | Pull-out, single handle | Flow plus dispenser | 2.2 GPM, dispenser included | Highest flow uses more water per minute |
| Glacier Bay McKenna HD67737-3001 | Pull-out, single handle | Shallow sinks | 1.8 gpm, 6-3/16 inch spout height | Short spout height limits clearance |
| GROHE Essence 32170000 | Pull-out, single lever | Single-hole decks | 1.75 gpm, 8-9/16 inch reach | Single spray pattern only |
How we selected
The shortlist comes from published manufacturer specification sheets and listing pages. A model had to be a true pull-out design, with the spray head drawing out of the spout body on a hose, and its published flow rate, spout dimensions and installation hole count had to be printed on the page, not inferred from photographs or category labels.
Models that appear only as pull-down designs were left out, because a pull-down head drops from a high arc while a pull-out wand travels forward out of a low spout, and the two suit different sinks. Finishes were recorded exactly as the maker or listing page names them. Where two pages printed different figures for one model, the manufacturer specification sheet figure is the one used in this guide.
Valve design was recorded for every model as well, because the cartridge or valve is the part that decides long-term drip behavior. That is why the buying guide compares ceramic disc designs against the Delta ball mechanism directly, instead of treating the valve as a footnote.
Kitchen faucets with pull out wand: the six picks
The six faucets below cover the pull-out patterns sold today: a low arc wand for shallow sinks, a longer hose for deep double bowls, and one model that adds a soap dispenser to the same deck footprint. Each entry states who the faucet suits, the published figures behind the pick, and the limit that could send a buyer to another model on the list.
Moen Brecklyn 87557SRS
The Brecklyn is the spray-first pick of this group. Its listing names the features plainly: faucet type pull out, a pull out spray wand, and a Power Clean spray function, with a flow rate of 1.5 GPM. Moen rates Power Clean as a stronger spray pattern for blasting food off plates, and the two-function wand switches stream and spray at the head.
The published dimensions fit smaller decks. Faucet height is 10.16 inches, the spout swivels 120 degrees, and the hole fit is listed as 3 hole or single hole, with an included deck plate covering the three-hole layout. The finish is stainless, described on the listing as a surface that helps reduce fingerprints and water spots. A single lever handle sits at the side of the spout base.
- Pros: Power Clean spray function for stuck-on food
- Pros: 120 degree spout swivel covers both bowls of many double sinks
- Pros: installs through one hole or three holes with the deck plate
- Cons: 1.5 GPM fills large pots more slowly than the 1.8 and 2.2 GPM models here
- Cons: low arc shape gives less clearance under the spout for tall stockpots
Buy if the daily work is rinsing, scrubbing and sink cleanup rather than filling tall pots. Skip if the sink is extra deep and a longer hose matters more than spray force, because the Delta below publishes the longer hose figure.
Delta Foundations B4310LF
Delta publishes the most complete hose data in this group. The Foundations B4310LF is a 2-function pull-out: the spout is 8-3/4 inches long and 8-29/32 inches high, it swings 120 degrees, and it operates in either spray or aerate mode. The spout connects to the valve body with a 59 inch hose, the longest published hose figure among these six picks.
Maximum flow rate is 1.8 gpm at 60 psi. The sheet lists single or 3 hole sink applications on an 8 inch centerset with the escutcheon. Inside, the lever handle control mechanism is a rotating stainless steel ball type with replaceable seats, and all operating parts are replaceable from the top. Delta lists a lifetime limited warranty on parts and finishes for this line.
- Pros: 59 inch hose reaches across wide counters and deep bowls
- Pros: 1.8 gpm flow rate fills pots faster than 1.5 GPM models
- Pros: operating parts replaceable from the top, per the maker sheet
- Cons: ball valve mechanism is an older design than the ceramic cartridges here
- Cons: plain styling will not anchor a design-led remodel
Buy if hose length is the deciding figure and the sink sits in a wide counter run. Skip if a ceramic cartridge is a firm requirement, because Delta uses its ball mechanism in this model instead.
Kohler Coralais K-15160
The Coralais builds its case on hose manners. Kohler describes ProMotion as a light, quiet braided hose with a swiveling ball joint, made for easier handling. The two-function sprayhead has touch control to switch from aerated stream to spray, and the MasterClean sprayface is an easy-to-clean surface that withstands mineral buildup.
The numbers are strong for a low arc faucet: 1.8 gpm maximum flow rate at 60 psi, a 9 inch spout reach and an 8-3/8 inch spout height. Kohler fits ceramic disc valves, and the faucet carries temperature memory, so it turns on at the temperature set during prior usage. Installation is single-hole or three-hole with the escutcheon included. The K-15160-AP pairs a polished chrome body with a white sprayhead, and Kohler lists premium metal construction.
- Pros: swiveling ball joint keeps the wand from fighting the user
- Pros: ceramic disc valves and temperature memory in a low arc body
- Pros: 9 inch reach is the longest spout reach in this group
- Cons: white sprayhead limits finish matching in stainless kitchens
- Cons: touch control on the head is one more part to learn
Buy if the wand will be in hand all day and hose behavior matters more than finish choice. Skip if the kitchen needs a stainless or dark finish at the sprayhead, since this version is white.
Pfister Marielle F532-7P
The Marielle posts the highest flow figure in this roundup: Pfister lists a 2.2 GPM flow rate for this pull-out kitchen faucet. The spray head is a 2 function pull-out sprayer, the spout swivels, and the valve is the maker Pforever Seal ceramic disc valve. Pfister lists all metal construction for the faucet body.
One feature sets it apart from the other five: a soap dispenser is included, and the dispenser is a top filling design, so the bottle refills from above the deck instead of from under the sink. Installation is 1 or 3-hole, with an optional deckplate, or single hole mounting. Mounting hardware is included in the box, per the maker sheet.
- Pros: 2.2 GPM is the fastest fill rate in this group
- Pros: soap dispenser included and refills from the top of the deck
- Pros: ceramic disc valve with all metal construction
- Cons: 2.2 GPM uses more water per minute than every other pick here
- Cons: traditional styling suits fewer modern kitchens
Buy if filling speed and a matched dispenser in the box top the list. Skip if water use per minute is a concern, because the other five models all publish lower maximum flow rates.
Glacier Bay McKenna HD67737-3001
The McKenna is the compact entry. Its specification sheet lists a spout height of 6-3/16 inches and a spout reach of 8-17/32 inches, the lowest profile in this group, which suits shallow sinks and counters with cabinets or shelves above the deck. The pull-out sprayer carries the maker TurboSpray feature, and maximum flow rate is 1.8 gpm at 60 psi.
The valve is a ceramic valve, listed by the maker for drip-free operation, and the handle is a zinc lever. Installation requires a 1- or 3-hole sink with 8 inch on-center spacing, and the sheet names a FastMount installation system. Two finishes are published: chrome as HD67737-3001 and stainless steel as HD67737-3008D2. Flexible supply lines with 3/8 inch compression fittings are part of the listed package.
- Pros: lowest spout height here, at 6-3/16 inches
- Pros: ceramic valve and 1.8 gpm flow in a small body
- Pros: two published finishes, chrome and stainless steel
- Cons: short spout height leaves little room for tall pitchers
- Cons: zinc lever handle rather than a brass or steel one
Buy if clearance above the sink is tight and the sink itself is shallow. Skip if the household fills tall pitchers daily, because the low spout will fight that routine.
GROHE Essence 32170000
The Essence is the single-hole specialist of the group. GROHE lists single hole installation, a swivel spout and a single spray pull-out with automatic returning, so the spray head draws back into the spout after use. Spout reach is 8-9/16 inches and maximum flow rate is 1.75 gpm.
Inside is the GROHE SilkMove ceramic cartridge, sized at 1.4 inches (35 mm), with an adjustable flow rate limiter for trimming the maximum flow at the faucet. The finish is StarLight Chrome. Stainless steel flex lines and a quick installation system are part of the published specification, along with integrated non-return valves and backflow protection.
- Pros: adjustable flow rate limiter built into the cartridge setup
- Pros: automatic returning pull-out keeps the head seated
- Pros: 35 mm ceramic cartridge from the maker SilkMove line
- Cons: single spray pattern, with no second spray mode published
- Cons: single hole installation only, so three-hole decks need the holes covered another way
Buy if the deck has one hole and a clean, minimal lever design is the goal. Skip if a second spray pattern or a three-hole fit without extra hardware is required.
Buying guide
A pull-out wand lives or dies by its hose, its docking and its published dimensions. The checks below use only figures a maker prints on a specification sheet, so a buyer can compare two faucets side by side without guessing from photos. Work through them in order: deck layout first, then hose and reach, then flow and valve design.
Hose length decides how far the wand travels
The hose is the key part of a pull-out faucet, because it sets how far the spray head can travel from the spout. In this group the published figures run from the Delta 59 inch hose down to models whose makers do not print a hose length at all. A deep farmhouse bowl or a compost bin beside the sink argues for the longest hose on the list.
Hose construction matters as well. Kohler publishes a braided hose with a swiveling ball joint for the Coralais, which keeps the wand from twisting against the hand. Where a maker prints no hose material, treat the hose as an unknown and weigh the models that publish their construction more heavily.
Flow rate, stated in gallons per minute
Flow rate decides both fill speed and rinse strength, and every maker here prints it. The spread in this group runs from 1.5 GPM on the Brecklyn to 2.2 GPM on the Marielle, with most models at 1.75 or 1.8 gpm at 60 psi. A household that fills pasta pots daily will feel the gap between 1.5 and 2.2 GPM at every meal.
Higher flow is not free. The 2.2 GPM model uses more water in a minute of rinsing than the 1.5 GPM model, and some local codes cap kitchen flow below that figure. GROHE answers with an adjustable flow rate limiter on the Essence, which lets the installer trim the maximum at the faucet itself.
One hole or three: match the deck layout
Deck layout rules out more faucets than any question. Most models here install through one hole or three holes, using an escutcheon or deck plate to cover the outer holes. The McKenna asks for 8 inch on-center spacing on its three-hole fit, and the GROHE Essence is single hole only, so a three-hole deck needs a separate plan for the spare holes.
Count the holes before ordering, including any hole already used by a soap dispenser or a filtered water tap. The Marielle includes its own dispenser, which claims one more hole in the deck. A four-hole sink with a dispenser hole already drilled can suit it well, while a one-hole deck cannot take the dispenser at all.
How kitchen faucets with pull out wand designs dock and swivel
Docking decides whether the wand sits flush or droops after a year of use. The Essence publishes automatic returning for its pull-out spray, and the Coralais pairs its hose with a swiveling ball joint so the head rotates instead of twisting the hose. A wand that docks loosely splashes the deck and wears its hose at the same bend point every day.
Swivel range is the other half of coverage. The Brecklyn and the Foundations both publish a 120 degree spout swivel, which covers a double bowl sink from a centered mount. A single wide bowl needs less swivel, while a corner mount needs more, so match the printed swivel figure to the sink layout rather than to habit.
Valve and cartridge designs to compare
The valve is the part that wears, so its design belongs on the comparison list. Ceramic disc valves or cartridges appear in the Coralais, the Marielle, the McKenna and the Essence, and makers publish them as their long-life option. Delta takes another route in the Foundations, with a rotating stainless steel ball mechanism and replaceable seats.
Service access matters as much as valve type. Delta publishes that all operating parts on the B4310LF are replaceable from the top, which avoids pulling the faucet from the deck for a valve service. Where a maker prints a cartridge size, as GROHE does with its 35 mm SilkMove cartridge, record it for future parts orders.
FAQ
These answers stick to what the makers publish about pull-out faucets: hose lengths, flow rates, hole counts and valve designs. Where a figure varies by model, the answer gives the range printed across this group rather than a single number, so the guidance stays tied to the specification sheets instead of general habit.
Can a pull out wand replace a side sprayer?
For daily rinsing, yes. A pull-out wand does the same work as a separate side sprayer: it delivers a spray stream on a hose to any corner of the sink. The difference is mechanical. A side sprayer is a deck fitting with its own hose, while the wand stores inside the spout, so a pull-out frees one deck hole and removes one hose from under the sink.
The trade is reach and flow. A wand is limited by its own hose, and the longest published hose in this group is 59 inches. A side sprayer can also keep working if the main spout is in use for filling, while a wand cannot run both stream and spray at once. Kitchens that rinse and fill at the same time may still prefer the separate fitting.
Do kitchen faucets with pull out wand models fit a three-hole sink?
Most of them do. Five of the six models in this guide publish a one or three-hole installation, using an escutcheon or deck plate to cover the outer holes of a three-hole deck. The exception is the GROHE Essence, which is listed for single hole installation only, so a three-hole sink would need the unused holes covered by other means.
Check the spacing as well as the count. The Glacier Bay McKenna specifies 8 inch on-center spacing for its three-hole fit, and the Delta Foundations sheet describes an 8 inch centerset. A three-hole deck drilled at a different spacing will not accept those escutcheons, no matter how the hole count matches.
How long are the hoses on these wands?
Published hose figures are thinner than buyers expect. Delta prints 59 inches for the Foundations B4310LF hose, the longest figure in this group. Kohler describes the Coralais hose by construction, a braided hose with a swiveling ball joint, without a length figure on the sheet. Several makers print no hose length at all for their pull-out models.
Because of that gap, hose length should be compared only where it is printed. If a model prints no figure, the honest reading is that its working reach is unproven on paper, and the spout reach figure, 8-9/16 to 9 inches across this group, becomes the firmer comparison point for sink coverage.
What flow rate should a pull out wand have?
The models here span 1.5 to 2.2 GPM, and the right figure depends on the work. Filling stockpots argues for 1.8 GPM or higher, which covers the Delta, Kohler and Glacier Bay models and the 2.2 GPM Pfister. Rinsing and cleanup argue for spray design over raw flow, where the Brecklyn Power Clean pattern works at 1.5 GPM.
Local rules can settle the question first. Some jurisdictions cap kitchen faucet flow, and a 2.2 GPM model may not comply where a cap applies. The printed maximum is also measured at 60 psi for most models here, so a house with lower line pressure will see lower flow from any of them.
Conclusion
Choose the Brecklyn for spray force, the Foundations for hose length, the Coralais for hose manners, the Marielle for flow and its included dispenser, the McKenna for tight clearance, and the Essence for a single-hole deck. Match the printed hole count, reach and flow rate to the sink first, and the wand will earn its place.